What steps should I take to find out what & where a program is constantly running on my computer. I have a Vista laptop comaq

Similar Questions

• How and where should I go to find out how to configure my joystick so I can use the joystick to use the flight simulation game that I bought from microsoft?

  I can't find out how to configure my joy (attack3) stick to play Flight Simulator. I don't want to use the keyboard on my computer to steal the game... Where can I find the instructions on how to configure and use the joystick?

  Hello

  1. what happens when you connect the joy stick?

  2. do you get an error message?

  3. what version of Windows are you using?

  Perform the steps mentioned below and check if that helps:

  Step 1:

  Flight Simulator x: using a gamepad

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=16624

  Step 2:
  Usually, vista Windows 7 will find and automatically install the necessary drivers when you plug your game controller into your computer.

  (a) connect the joystick to the USB port via the adapter.

  (b) see if it is detected.

  (c) Windows should recognize the new hardware and set in place to work properly.

  If this isn't the case, install the relevant drivers for gamepad for the manufacturers Web site.

  Step 3:

  I suggest the following steps and check for the device.

  1. in Control Panel, open game controllers. To do this, use one of the following methods:

  a. click Start, typejoy.cpl in the Search box and press ENTER.

  2. click on your game controller, and then click Properties.

  3. on the Test tab, test the game controller to verify functionality.

  Here is the link:

  http://support.Microsoft.com/kb/831361

  I hope this helps.

• After a system restore to a time before Windows XP, should I leave Safe Mode and restart normally? What other steps should I take in Mode safe?

  After a system restore to a time before Windows XP, should I leave Safe Mode and restart normally.  Completely restored restore operation the registry both before the intrusion of viruses if the date and time specified as the restore point is earlier than the time of the intrusion, but in the same 'on' the cycle of computer?  I have to do something else before going back to safe mode?

  Time as about 23:00 last night 7/29 restoration, first known intrusion by "XP Home Security 2012" was shortly after midnight 7/30.

  I ended up a sde.exe process, which stopped the pop-ups.  A full scan with Norton quarantine, JS. SecurityTool.  After a restart of the computer, the normal features of the programs has been lost by the "Run" menu or icons on the desktop.  By clicking on the icon for the normal .exe files redirected to the dialog box "select a program to open.

  I restarted in Mode safe mode with networking and then restore.  I tried opening IE and Excel and that they work properly in Mode without failure.  They will work correctly when I leave Safe Mode and restart normally.  Should I test other specific applications.

  XP Home Security 2012 seems to have accessed or modified some files to DropBox (not sure how this program was installed, but it was already on).

  Should I delete all DropBox files, just those showing a modification date corresponding to the intrusion of XP Home Security 2012, or don't you worry about this?

  After a system restore to a time before Windows XP, should I leave Safe Mode and restart normally.  Completely restored restore operation the registry both before the intrusion of viruses if the date and time specified as the restore point is earlier than the time of the intrusion, but in the same 'on' the cycle of computer?  I have to do something else before going back to safe mode?

  Time as about 23:00 last night 7/29 restoration, first known intrusion by "XP Home Security 2012" was shortly after midnight 7/30.

  I ended up a sde.exe process, which stopped the pop-ups.  A full scan with Norton quarantine, JS. SecurityTool.  After a restart of the computer, the normal features of the programs has been lost by the "Run" menu or icons on the desktop.  By clicking on the icon for the normal .exe files redirected to the dialog box "select a program to open.

  I restarted in Mode safe mode with networking and then restore.  I tried opening IE and Excel and that they work properly in Mode without failure.  They will work correctly when I leave Safe Mode and restart normally.  Should I test other specific applications.

  XP Home Security 2012 seems to have accessed or modified some files to DropBox (not sure how this program was installed, but it was already on).

  Should I delete all DropBox files, just those showing a modification date corresponding to the intrusion of XP Home Security 2012, or don't you worry about this?

  System Restore IS NOT the way to remove malware. The reason why you do not see the effects of the malware in safe mode is probably due to the fact that the process for most malware does not load in safe mode, and therefore not active.

  Restart the computer in Safe Mode with network. Click HERE. Download Malwarebytes. Update Malwarebytes and perform a full scan.  Choose to quarantine found nothing. Once completed click HERE and download Superantispyware Portable. Run a full scan quarantined found anything yet. Restart your computer in normal mode and perform a quick scan with Malwarebytes.

• Within a single class what steps should I take to implement a selection MenuItem "get"?

  I have a single class that extends screen that contains a single menu that contains MenuItems:

  • New
  • Edit
  • View
  • Output

  For the New, Edit and display screens, I just want to use a class that extends the screen.

  When one of these MenuItems are selected, I need to be:

  1. Get an identifier for the class that extends the screen, looking at the method MenuItem.getId ().
  2. Pass a parameter of the run() method in MenuItem to the class that extends the screen.

  The goal of each is well just to get a unique identifier that tells the screen to get the various parameters to change the layout of the screen and repaint.

  What is a good design implemented or the best implementation which is recommended?

  Thank you

  passing the parameter or by calling a setter on the screen are very good.

• to use the help of a friend (distance) the configuration steps should I take?

  Hello

  use the help of a friend remotely, configuration steps I have to take?

  1. I see nothing in the services to enable

  2. I don't see anything in the windows firewall so that it

  3. what one thing I see in the computer properties in the Advanced section, I can help vink (enable) of distance.     Wil only be this option enough to get help from a friend or remotely?

  My second question is

  I know there are third party software to make contact with the client computer (remote assistance).

  are there any simple quiet easy to use for customers and third party free software, if so wat is the name of it?

  Thank you

  Johan

  Hi Johan

  You can use built-in Windows 7 Remote Assistance.

  What is Windows Remote Assistance? :

  http://Windows.Microsoft.com/en-us/Windows/what-is-Windows-remote-assistance#1TC=Windows-7

  There are also third-party products.

  Access, manage and support computers remotely:

  https://secure.LogMeIn.com/

  TeamViewer:

  http://www.TeamViewer.com/en/index.aspx

  Concerning

• Try to find out which version of Adobe Premier is compatible with my computer

  Hello everyone, I am in the process of transition in Adobe video editing software. I have used Final Cut Pro for the past (12) years and I'm finally deserting a ship. I was wondering that if I could get some guidance as to what Version of Adobe editing work better with my Machine. I have a Power Mac Pro (mid 2010). Below you will find my profile. By comparing what my machine is composed of and do not bounce these specifications out of my mine are like trying to read the hieroglyphics, at least for me. Thank you all for your help and I'm really excited to start using this software and interact online with what I know is some very technically savvy technicians and artists. Thank you!

  Treatment

  8-core (standard configuration) two-processor 2.4 GHz Quad - Core Intel Xeon E5620 "Westmere".

  12 MB cache L3 entirely shared by processor

  Turbo Boost dynamic performance up to 2.66 GHz Hyper-Threading technology for up to 16 virtual cores

  Quad-core

  (standard configuration) A processor at 2.8 GHz Quad - Core Intel Xeon W3530 "Nehalem".

  8 MB cache L3 entirely shared by processor

  Turbo Boost dynamic performance up to 3.06 GHz

  Hyper-Threading technology for up to 8 Virtual cores

  Advanced Intel microarchitecture

  Integrated memory controller

  SSE4 SIMD 128-bit engine

  64-bit data paths and registers

  Optimized for energy efficiency

  Audio connections

  Four ports FireWire 800 (two on the front, two on back panel)

  Five USB 2.0 ports (two on the front, three on the back panel)

  Two USB 2.0 ports on keyboard included

  Taken minijack headphone of façade and internal speaker

  Audio digital optical and output TOSLINK ports

  Mini-prises of output and analog stereo line level input

  Multichannel audio via Mini DisplayPort

  Graphics and displays

  Double width, 16 channel PCI Express 2.0 graphics slot with one of the following installed graphics cards:

  ATI Radeon HD 5770 with 1 GB memory GDDR5, PCI Express 2.0, two ports Mini DisplayPort and DVI port to double bond

  ATI Radeon HD 5870 with 1 GB memory GDDR5, PCI Express 2.0, two ports Mini DisplayPort and DVI port to double bond

  Possibility of installing two cards ATI Radeon HD 5770

  Support for up to six screens

  Support for digital resolutions up to 2560 x 1600 pixels

  Support of analog resolution up to 2048 x 1536 pixels

  Video cards available for:

  Additional DVI output Mini DisplayPort to DVI (optional)

  Additional dual-link DVI, output Mini DisplayPort to DVI dual link (optional)

  Output VGA Mini DisplayPort to VGA or DVI to VGA Display Adapter (optional)

  Memory

  Dual processor systems

  2.4 GHz system: 1066 MHz DDR3 ECC SDRAM

  2.66 GHz and 2.93 GHz systems: 1333 MHz DDR3 ECC SDRAM

  Eight memory slots (four per processor) supporting up to 64 GB of memory main using 1 GB, 2 GB, 4 GB or 8 GB DIMMs

  Single processor systems

  2.8 GHz and 3.2 GHz systems: 1066 MHz DDR3 ECC SDRAM

  3.33 GHz system: 1333 MHz DDR3 ECC SDRAM

  Four memory slots supporting up to 32 GB of memory main using 1 GB, 2 GB, 4 GB or 8 GB DIMMs

  The system configuration required

  Premiere Pro - http://helpx.adobe.com/premiere-pro/system-requirements.html

• Test to run to find out which version of DirectX, I'm running

  DirectX test

  Click Start and type "dxdiag" in the search box, and then press ENTER. The window that displays a list of system information, in the lower will be your version of DirectX.
  Note:
  If you have XP you have DX9 at least, but probably DX10/11
  If you have Vista you have DX10 probably DX11
  If you have windows 7 you have DX11

  I hope this helps.

• I have windows vista and I had to use my recovery disk, but an error came as it ended. I tried to use the menu options of recovery but now she plays as if I had no drivers. What should I do?

  I used my recovery discs and some sort of error came. so, it has not fixed the computer. so I think that some how drivers were not loaded. However what seems to be a driver came when I press my f12 button to use the system recovery options menu. but I insisted on using it, and another box came to tell the software installation media or something to use to load the drivers. I also tried to use the Startup Repair tool restore and system by surprise that I have on an external drive listed under windows backup care but nothing has worked. I don't know anything else to do.

  1. Open the 'computer '.
  2. Right-click on the drive in question
  3. Select the tab "Tools".
  4. In the error-checking box, click .

  Well you can suffer the consequences of not running it who are often worse. CHKDSK found and try to
  repair disk problems, it does not really create them.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

• Did someone already bought a HP dv9700 Entertainment PC & find out more late it is a model of dv9810us?

  Hello.  Has anyone ever bought a HP dv9700 Entertainment PC to find out later that it is actually a model of dv9810us?

  I bought my laptop as a HP dv9700 Entertainment PC. However, the properties of the system display incorrectly.  The property system indicate that it is a HP dv9700 Entertainment PC like the box your laptop came in; however, sticker service tag on the bottom of sweep of website of the laptop AND my laptop for drivers of HP indicated the model is a dv9810us.  A specialist of the HP Support told me that the models failed to height in the properties of the system due to an error in Imaging, but I'm not sure about this because I'm not familiar with the operation of the "imaging".  I guess it probably has some kind of ini or another file (or something) that tells it what to display system properties.

  Anyway, has everyone except I never bought a laptop to learn later that this is not the model you thought you bought?  I really want to hear from you if this has happened to GOLD if you know why this happened to me.  The only reason I found out that it of because I started having problems with the device and was looking for drivers to download from HP and the pattern does not match.

  Thanks for your time and your answers!

  Have a fantastic day,

  Tammy :-)

  Thanks for letting me know the system information is pulled from the BIOS. However, don't would not support HP on HP Web site scanning detected the correct when model it detected my model as a dv9810us as opposed to the dv9700 shown in my System Info?   It seems that everything points to a dv9810us except the system information.

  Earlier, I noticed that besides the service tag indicating it's a dv9810us, the sticker on the laptop near the keyboard said also that my laptop is a HP Pavilion dv9810us Entertainment PC (instead of HP Pavilion dv9700 Entertainment PC).  It seems that the BIOS must have incorrect information as well.  I've ALWAYS relied on my system information to be correct, but in this case, it is incorrect.

  I still don't understand WHY this happened. The information system has been the same since I bought the laptop but I never had any issues so far, so it didn't matter.  This error/mixup with the model numbers were able to settle the bad sound and drivers QTOSD before I decided to use the Restore Manager feature to try to get this back to factory driver settings.

  Once again, thank you very much to tell me where the information system is shot, but I still don't know why it would be wrong, but it seems not be wrong.

  Good day!

  Tammy

• I tried to clean my screen with moisture and got some inbetween can I take my screen out I have a Dell laptop

  I cleaned my laptop screen with a Kirkland optical care kit, it's a lens clearner and I got some inside my

  my screen humidity can I take the four little screws ot of the corners to get to the screen, I have a Dell laptop

  I thought using it will clear up, but must have a leak.

  Larry at * address email is removed from the privacy * thank you

  I cleaned my laptop screen with a Kirkland optical care kit, it's a lens clearner and I got some inside my

  my screen humidity can I take the four little screws ot of the corners to get to the screen, I have a Dell laptop

  I thought using it will clear up, but must have a leak.

  Larry to * address email is removed from the privacy * thank you

  Contact Dell support. But, you've probably ruined for good.

• Hearing cc 2015 is able to deconstruct an OMF song in its component titles? If this is not the case, what kind of program can? Thank you

  Hearing cc 2015 is able to deconstruct an OMF song in its component titles? If this is not the case, what kind of program can? Thank you

  I'll have to give you a qualified Yes.

  When a sequence or project is exported as an OMF file, the resulting OMF file contains a description of your audio editing (the clip in the Timeline and exit points) as well as audio files. You can use the command Export OMF if you plan to deliver your audio files to a Publisher using a digital audio-OMF-compatible station (DAW). Most of the audio facilities are capable of using OMF files.  The problem is, OMF is one of the most abused, interpreted as 'standards' autour, and lots of other audio editing programs do not correctly.

  The best I can say is try it and see.  However, if there is a problem, can I suggest that you look at a nice little app called "AATranslator" available at AATranslator - homepage

  This was written by a user of hearing to smooth a bunch of problems that produce projects exchange of a wide range of DAWS - and the good thing is that the creator is a regular here so support tends to be pretty darn good!

• How can I find out what characteristics should be power in the "turn Windows features turn on or off.

  In the section (turn Windows features on or off) how can I find out what characteristics must be on, and which must be disabled? I looked everywhere for something to tell me what are the characteristics and that it uses has been, but I am not able to find something on the subject... Could you please tell me which ones should be on and which should be turned off. Thank you.

  Hello

  It's the kind of choice: (maybe this will help you decide)

  Feature of Windows Vista Guide
  http://www.bleepingcomputer.com/tutorials/tutorial134.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• How can I find out what programs I should have started and what are the programs I can start myself to my computer to run correctly when starting?

  * Original title: startup

  How can I find out what programs I should have started and what are the programs I can start myself to my computer to run correctly when starting?

  Hello

  I understand you want to learn about programs, you should start your Windows startup. I will certainly help you to question.

  When you start Windows by using a normal startup startup, several applications and services automatically, and then run in the background. These programs include the base system, antivirus software, utility applications processes system and other software that was previously installed. These applications and services may cause interference when you install or run a program.

  The system configuration is a tool that can help identify problems that might prevent Windows from starting correctly. You can start Windows with common services and startup programs turned off and then reactivate them, one at a time.

  I suggest you to refer to the links below and check if this is useful:

  Using the Configuration System (msconfig)

  Perform a clean boot to determine if background programs interfere with your game or program

  Hope this information helps.

  Please get back to us with an update on the issue, we will be happy to help you.

• How can I find out what programs are essential to start?

  Original title: slow start

  How can I find out what programs are essential in the implementation, we can stop?

  Windows Home vista 32 premium

  Hey Stella-50,

  How slow is slow? For example, my machine (e-machine E4264 2.2 ghz with 2 GB RAM) boots in 95 seconds. For me, I call it, in the average. I am currently in the process of looking for a new machine because it is already 3 years old, so maybe that OEN will be slightly faster to start.

  What you can 'turn off' will depend on which in fact initially launches upward and, unfortunately, you have not told us that at this moment. Is that you should not disable your anti software anti-virus (updater). nothing to do with your mouse and your keyboard etc.

  Perhaps, if you made a list of what application are actually being run at startup (via the msconfig Startup tab) can someone take a look at them and see if, or what can be disabled.

  Otherwise, you might take a glance at Startup Delayer http://www.r2.com.au/software.php?page=2&show=startdelay to see if you can delay the time different applications load to allow windows to start up more quickly. I haven't used so I can't say how good/bad it is.  It's a freeware.

  Here is a review of PCWorld magazine http://www.pcworld.com/downloads/file/fid, 73002-order, 6 pages, 1/description.html

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: www.winuser.co.uk | vistasupport.mvps.org | xphelpandsupport.mvps.org | www.silversurfer-Guide.com

• Please inform me how to find out what is my user name.

  Please inform me how to find out what is my user name, so that I can install my upgrade to Flash Player.

  What userid & password should I install Flash Player?