When I start the system, I get the message "failed to load Launcher dll" I hit OK and the system load and seems to work.

Similar Questions

• When I start my computer I get a message that says that the file < root windows > \system32\hal.dll. is damaged or missing.

  file HAL.dll

  When I start my computer I get a message that says that the file \system32\hal.dll. is damaged or missing. Please reinstall a copy of the file. I have the original Windows XP CD and I tried to re - install, but it will not go beyond the implementation of window. I can't sign in to windows. How can I reintall this file?

  It's extremely likely that you will need to replace the hal.dll and since there are seven files on the XP installation CD that will extend into hal.dll, which would you choose?  It depends on your hardware, but it is extremely likely that the problem (did I already say that?).  I've never had to replace a file hal.dll for this problem.

  The real problem is most likely that XP just can not find the file because of a file system corruption or a file c:\boot.ini afflicted.

  For this error, I would always be first boot from the XP Recovery Console and sometimes run a chkdsk-r that will fix things right to the top.

  If the chkdsk /r is clean and you have the same problem, and then re-create your c:\boot.ini file but rename the old one first so you don't build on top of those afflicted - this tidbit is absent from MS KB article that assumes too.

  You can do all this in the XP Recovery Console, but do go through these methods in this article and see how you go.

  For example, method 1 will not work if your system does not start.  You may have more luck with other "methods".

  If that doesn't work, then I suggest to provide a little more information about your system:

  Since the Microsoft Answers forum does not have any kind of information system request when a new question is asked, we know absolutely nothing about your system.  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Thank you MS Answers, allowing the resolution of simple problems as frustrating and a lot of time as possible.

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Your system have IDE or SATA disks?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  You have a real installation CD bootable XP which is the same Service Pack as your installed Service Pack? (this is not the same as any recovery CD provided with your system)?

  If the system works, what do you think might have changed since the last time it did not work properly?

• When I start my computer I get a message saying c:windows\system32\ambrune.dell, how do I solve this problem?

  When I start my computer, I get a message saying c:windows\system32\ambrune.dell how can I solve this problem?

  Original title: ken asked

  See: http://answers.microsoft.com/en-us/windows/forum/windows_7-performance/cwindowssystem32ambrunedll-the-specified-module/5c928ca6-e7e3-40ab-87f4-0224c2fc7759?msgId=c3b91db6-876f-484c-8216-2ffce4473a24

• When I start my computer, I get this message: fm3032.exe. application error fail to initialize and it is not allowing me to open the files on my desktop or access the system restore? My OS is XP

  My operating system is windows xp

  http://www.file.NET/process/fm3032.exe.html

  Read this thread and see if you have list them installed programs.

  Also, follow these steps:

  Download, install, update and scan with these full free malware detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/

  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  http://www.Microsoft.com/security/scanner/en-us/default.aspx Security Scanner   

  Post back with the results of the analyses and also answer the following questions:

  brand and model of the pc

  current antivirus

  What service pack?

• When I start my computer I get an error message about V protect Application on the Windows XP-based computer

  When I start my computer, I get an error message, "V Protect Application has encountered a problem and needs to close".

  System information Utility version 1.0.0.1

  OS version: Microsoft Windows XP Home Edition, Service Pack 3, 32-bit

  Processor: Intel (r) Celeron (r) CPU clocked at 2.66 GHz, x 86 Family 15 Model 4 Stepping 1

  Number of processors: 1

  RAM: 1 GB

  Graphics card: RADEON 9250, 128 MB

  Hard disks: C: Total - 76316 MB, free - 47785 MB; KC: total - Mo 305168, Free - Mo 304760;

  Motherboard: MICRO-STAR INTERNATIONAL CO., LTD, P4M266-8233,

  Antivirus: AVG Free Antivirus, update: Yes, On-Demand Scanner: enabled

  I run the above system and would appreciate any help with the removal of this message as if I don't send it to Microsoft, it goes.

  Thank you

  Roy.

  You can try those Microsoft committed the 'experts' ideas Support Engineer (1, 2, 3) for safe, clean boot Mode, Online Scanner, but I think that most of the people who know how XP would recognize that there is no component 'V protect' in Windows XP and a simple search Google reveals that your problem is with your AVG software and has nothing to do with Windows XP.

  You should look in their forums (like me) and here's what they suggest:

  Vprotect belongs to AVG Security Toolbar.
  Please try to run repair installation using the latest installation package.

  If the problem persists, please follow all the steps in the instructions to complete reinstallation .

  I think that if I were you, I would follow the instructions on the page AVG to uninstall and reinstall your AVG because there may be other parts of AVG who are afflicted that you have not yet discovered, but in AVG, some people with V forums protect problems find that AVG repair install works.

• Get a box to enter the password when you start the computer

  * Original title: turn my computer

  When I start my computer, I get abox asking you the windows xp startup password.  This has never happened before and I don't know the password.

  Hello

  -Have there been recent changes made on the computer before the show?

  I suggest you to check if you can connect to your account or the account of default administrator in safe mode.

  Check out the link for more information on how to enter Safe Mode.

  A description of the start in Windows XP Mode options:
  http://support.Microsoft.com/kb/315222

  a. the built-in Administrator account is disabled by default.

  b. you will see an icon for the administrator on the homescreen mode without failure.

  c. connect you (the password will be a white)

  If you are able to start the computer in safe mode, try to check and restore the system.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  Important: System Restore will return all your files non-system as documents, email, music, etc., to a previous state. These files of types are completely affected by the restoration of the system. If it was your intention with this tool to recover a deleted file to non-system, try using a file instead of system restore recovery program.

  Please get back to us with the information above to help you accordingly.

• When I start the listener, I get the following "status UNKNOWN"...

  Oracle 11g R1 on Oracle Enterprise Linux
  
  
  Here is the configuration of my listner
  **********************************************************************
  [oracle@oracle-test admin] $ cat listener.ora
  listener.ora # Network Configuration file: /u01/app/oracle/product/11.1.0/db_1/network/admin/listener.ora
  # Generated by Oracle configuration tools.
  SID_LIST_LISTENER =
  (SID_LIST =
  (SID_DESC =
  (SID_NAME = PLSExtProc)
  (ORACLE_HOME=/u01/app/oracle/product/11.1.0/db_1)
  (= Extproc PROGRAM)
  )
  (SID_DESC =
  (GLOBAL_DBNAME = orcl.o - test.mydomain.name)
  (ORACLE_HOME = u01/app/oracle/product/11.1.0/db_1)
  (SID_NAME = orcl)
  )
  )
  
  LISTENER =
  (DESCRIPTION_LIST =
  (DESCRIPTION =
  (ADDRESS_LIST =
  (ADDRESS = (PROTOCOL = TCP)(HOST = xxx.xx.xx.xx) (PORT = 1521))
  )
  (ADDRESS_LIST =
  (ADDRESS = (PROTOCOL = CIP)(KEY = EXTPROC1521))
  )
  )
  )
  
  *************************************************************************
  
  
  
  
  When I start the listener, I get the following messages of "Status UNKNOWN".
  
  
  Why?
  
  
  
  [oracle@oracle-test bin] $. / lsnrctl start
  
  LSNRCTL for Linux: Version 11.1.0.6.0 - Production on February 19, 2010 11:22:04
  
  Copyright (c) 1991, 2007, Oracle. All rights reserved.
  
  From /u01/app/oracle/product/11.1.0/db_1/bin/tnslsnr: Please wait...
  
  TNSLSNR for Linux: Version 11.1.0.6.0 - Production
  System settings file is /u01/app/oracle/product/11.1.0/db_1/network/admin/listener.ora
  Log messages written to /u01/app/oracle/product/11.1.0/db_1/log/diag/tnslsnr/oracle-test/listener/alert/log.xml
  Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=xxx.xx.xx.xx) (PORT = 1521)))
  Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))
  
  Connection to (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST=xxx.xx.xx.xx) (PORT = 1521)))
  STATUS of the LISTENER
  ------------------------
  Alias LISTENER
  Version TNSLSNR for Linux: Version 11.1.0.6.0 - Production
  Start date February 19, 2010 11:22:04
  Uptime 0 days 0 h 0 min 0 sec
  Draw level off
  Security ON: OS Local Authentication
  SNMP OFF
  Parameter Listener of the /u01/app/oracle/product/11.1.0/db_1/network/admin/listener.ora file
  The listener log file /U01/app/Oracle/product/11.1.0/Db_1/log/diag/tnslsnr/Oracle-test/listener/alert/log.XML
  Summary of endpoints listening...
  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=xxx.xx.xx.xx) (PORT = 1521)))
  (DESCRIPTION = (ADDRESS = (PROTOCOL = ipc) (KEY = EXTPROC1521)))
  Summary of services...
  Service 'PLSExtProc' has 1 instance (s).
  Instance of 'PLSExtProc', status UNKNOWN, has 1 operation for this service...
  Service "orcl.o - test.mydomain.name" has 1 match (s).
  Instance "orcl", status UNKNOWN, has 1 operation for this service...
  The command completed successfully

  There is nothing to worry about it. UNKNOWN means, the listener knows the orcl SID because of the list of SIDS. This is called static record. If your instance orcl's up, PMON dynamically registers the listener (if you are using port 1521 without additional configuration), which leads to a READY State.

  Kind regards
  Uwe

  http://uhesse.WordPress.com

• I have a Canon MG6120. When I start it up I get the error code 5050. Does anyone know how to fix this?

  I have a Canon MG6120 all-in-one. When I start it up I get the error code 5050. Does anyone know how to solve this, more power to the wide / power?

  Hello gregg.

  Please, try the following to see if we can solve your problem:

  1. turn off the printer.

  2 disconnect the power from the printer for at least 5-10 minutes.

  3. once unplugged, remove any paper from the device.

  4. check for obstructions in the paths of the unit or the paper.

  5 If no obstacles are, plug the power back in and switch on the device.

  If the problem persists, the unit will require repairs for the correction.  We apologize for the inconvenience.  Please contact our support group using the 'Contact us' below for further assistance.

  It has not responded to your question or problem? Find more help at the Contact Us.

• When windows starts, the user name is not displayed, almost all programs do not work, or I get a message saying that they do not have authorization to run the service

  When windows starts the user name is not displayed, almost all programs do not work, or I get a message saying that they have permission to run the service, sometimes windows not loading some programs of initialization and I can't turn off the pc by using the start menu, when it arrives, sometimes everything works normally when I turn on the pc except of my antivirus (avast!) and firewall (comodo) , they are responsible, but avast! said that the service is disabled and when I him there is a message saying that he had ceased to maximize or in an inconsistent state and comodo said that the application of the agent is not running.

  My Windows is XP Professional SP3.

  Thanks in advance.
  (Sorry for my English)

  * original title - I have starting problems I've ever had and I can't find a TomTom.*

  Salvation exodus REV,

  You did it of any material changes or software on the computer before this problem?

  I recommend you to uninstall Avast! & Comodo temporarily from Add / Remove Programs. Later, check to see if the problem persists.

  To uninstall Avast!, you can use utility aswClear to uninstall Avast!.

  For more information, refer to this link: Uninstall Utility

  You can not install Comodo since Avast! has a built-in & antivirus firewall.

  Hope the helps of information.
  Please post back and we do know.

• When I start my computer, I get an errror messege, (c:\program v1.8.4 specials\webspec.dll, the specified module could not be found

  WHEN I start my computer I get an error message, (program v1.8.4 specials\webspec.dll specified module cannot be found

  Hi stinger2165,

  1. did you of recent changes on the computer?

  2 when was the last time it was working fine?

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• When I start the system upward, it goes to my logon screen and the computer crashes

  I have a windows vista computer and when I start the SUST until it goes to my login screen, I connect the Welcome screen comes the computer hangs... I do a control-Alt - Delete that returns the desk top

  When you get on the desktop, open the start menu to search msconfig and press ENTER.

  When the popup window appears, it should start under the general tab, and you should see normal startup. For now, set it to start diagnosis, press ok and restart the computer. If it still crashes, then replace the and set it back to normal startup, as something else is causing this problem.

  If she does not hang, and then back up the, set back to normal and this time go to the Startup tab. The list is all the things that are set to start when you start your computer. One of them is causing the computer to crash.

  If you have an idea that it might be that you can deselect it, apply, then reboot and see if it still crashes. Or you could just go in the list, one at the same time turn them off then restart suspended far, so you know which is the cause.

• When I start my computer, I get a screen that tells me the EULA has expired and I need to call the computer of the company rented to renew, however is not a rental?

  When I start my computer, I get a screen that tells me that the CONTRACT has expired and I need to call the company, that the computer can be rented to renew, however is not a rental? I have no idea what this same refers to, however, it gives me a password to enter, tells me that I have to wait 10 minutes, then it resets a chipset and allows the computer to, and then starts. I can't even take a screenshot of this message, because what it comes to control over the computer. I've scabbed virus and comes back clean. All this shows is a name of agent: HLZR4G1, then the Version 5.6.5 (Build-a-1028). The password was Wanker that seemed fishy, now the password is numbers and letters. Can someone explain this to me?

  Hello

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  make it work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• I get "Can'tOpenLogFileException ' when I start the computer

  When I start the computer, I get the following: path to the file Can'tOpenLogFile Exception: newspaper: C:\ProgramData\Juno\Accelerator\MainException.log,open mode: 10 to WinMain(.\main.cpp:170) caused by: failure of fopen with errno ErrnoException:Call (2) "no such file or directory"

  When I try to open Juno he opens not and said that Juno detected error then the next screen is a Windows form that says "Juno has stopped working.  A problem caused the blocking of the work programme...
  I need to open the Juno - Please HELP!  Relocation of Juno changes nothing!

  I uninstall Juno and then reinstall again - maybe that will create the appropriate links and do work (it cannot be initially installed correctly) - don't reinstall it just (uninstall first).

  If this does not work, please transfer your question in the Forum program: http://social.answers.microsoft.com/Forums/en-US/vistaprograms/threads where people who specialize in programs that are not Vista or IE will be more than happy to help you with your problem.

  Good luck! Lorien - a - MCSE/MCSA/network + / A +.

• My Lightroom worked the perfect time, but today when I start the program I get a message "Lightroom has stopped working".

  My Lightroom work all the perfect time, but now when I start the program I get a message "Lightroom has stopped working".

  I use Windows 7 pro SP1and Photoshop and Lightroom CC. I think that it is a more recent version.

  Yes, I use the administrator account

• I can't install the update when I start the creative cloud. I'm getting an error 1002. I run a PC with Windows 7, 64-bit version.

  I can't install the update when I start the creative cloud. I'm getting an error 1002. I run a PC with Windows 7, 64-bit version.

  Hello

  Please, try the following steps:

  • Uninstall Adobe CC (Creative Cloud help |) Uninstall the creative Office Cloud app)
  • Reboot the computer.
  • Install the latest Adobe Creative cloud version from the link: CC help | Creative cloud desktop

  Kind regards

  Sheena