When I try to start the Remote Access Connection Manager in services.msc, the service will not start.

Similar Questions

• Can not get to start remote access connection manager and the connections don't work Internet

  Original title: wired & wireless connections does not.

  I can not get the remote access connection manager to start and so no internet connection is not working, also I can't open the system restore to go back on this machine. What is this?

  I am running a Dell Studio 1735 PP31L w model number / Edition Vista Home premium.

  Hi Rick,

  1. what happens when you try to start the remote access connection manager? You receive messages or error codes?

  2. you receive error codes or restore messages when you perform the system?

  You can check the status of the following services and make sure that the services are started.

  a. Click Start and type Services in start search and press ENTER.

  b. in the services with the right button on the phone and then click Properties.

  c. under the general tab, select automatic next to startup type.

  d. under the general tab, click Start under the service status and then click apply and then click OK.

  e. Repeat steps c & d to the remote access connection manager and Remote Access Auto Connection Manager service.

  Hope this information is useful.

• Error 1068: the dependency service or group failed to start and failed to start the remote access connection manager service.

  Original title: Windows could not start the service of connection manager on the local computer remote access

  amplifier

  Windows could not start the service of connection manager on the local computer remote access

  Error 1068: The dependency Service or group could start.

  Hi sunelchandraoli,

  1. when exactly you receive this error?

  2. you remember to make changes to the computer before this problem?

  Step 1:

  "Make sure that all the services of the dependence of the"Remote Access Connection Manager"" are launched in the list of services...

  a. Click Start, type services.msc in the box start the search.

  b. select Services from the list programs. If you are prompted for an administrator password or a confirmation, type your password or click on continue

  c. right click on the Remote Access Connection Manager service and then click Properties.

  d. under the general tab, click Manual next to startup type.

  e. under the general tab, click Start under the service status and then click OK.

  f. also check for long-term services.

  The dependency of 'Remote access connection manager' services include:

  i. secure Socket Tunneling Protocol Service

  II. telephone

  III. Plug-and-Play

  IV. Remote Procedure Call (RPC)

  c. of DCOM Server process Launcher

  VI RPC end point mapper.

  Make sure that the above services are started in the services list. If this is not the case, start all services above and check.

  Step 2:

  You can also try a system restore to a prior restore point you have been affected by the issue.

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  To run the system restore, you can consult the following link:

  System restore

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Hope this information is useful.

• Failed to start Remote Access Connection Manager Service. Get the 20 error: the system cannot find the specified device.

  This seems to have started with the last batch of updates of Windows 7 (including SP1).
  I can't connect using dial-up.  Get the message:
  Cannot load the Remote Access Connection Manager service
  Error 711: The operation could not complete because it could not start the remote access connection manager service
  in time.  Please try the operation again.

  When I try to start the Remote Access Connection Manager service manually, I get the message:
  Windows could not start the service on Local computer remote access connection manager.
  20 error: the system cannot find the specified device.

  My phone displays the modem works properly, and telephony and the Secure Socket Tunneling Protocol service started.

  I don't know what else might have changed.

  Hello Vince_867,

  Thanks for your post.  Take a look at this thread for a possible solution to your problem.

  See you soon

• The remote access connection manager could not start. Error 2: cannot find the specified file.

  I've updated from vista to the most recent update.

  I have windows vista Home premium 32-bit.
  I want to get this matter resolved without having to reinstall as I have a few games installed it on this system.
  The modem is not the issue as other computers connect very well.
  Thanks for the help from Microsoft.
  Recently, I tried to connect to the internet but that was not possible, because no connection could be established. The remote access connection manager does not start 2 error: could not find the specified domain. the RasMan-dependent services are started, but Manager logins remote does not start.

  Hi Mundilfar,

  You can try the folliwng steps and see if it helps.

  Step 1:

  You can try to scan the file system [SFC] checker on the computer that will replace missing or corrupt files & check if the problem persists.

  For more information, you can consult the following link.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  Step 2:

  If you are always faced with the question, then you can try to give permission for the Rasman registry key and see if it helps.

  Important: The following steps show you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, follow the steps from the link below:

  Back up the registry

  a. Click Start, type regedit in the search box and press ENTER.

  b. Locate the following subkey:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\RasMan

  c. right click on the key and click Permissions.

  d. Select Advanced, click on owner tab, click your user name, and check the 'Replace owner of subcontainers and objects', click Apply - click OK.

  e. click the user or group name that you want to work with.

  f. check allow total control. Click apply and then click OK.

  g. restart the computer and check.

  Hope this information is useful.

• Why can't I start Remote Access Connection Manager

  I am not able to connect to internet using my 3G Broadband. I try to resolve the status of the remote access connection manager to "on the road", but the error message invites up to said "Windows could not start the service on local computer remote access connection manager. Error 1068: the dependency service or group could start. "I find the dependencies are Remote Access Auto Connection Manager, routing and remote access, Sharing (ICS) to connect Internet. I tried to put those 3 to "started", but was able to start also.

  Hello
   
  You must make sure that the underside of services are started and restart your computer and check if the problem is resolved.
   
  To start the services.
   
  1. click on start.
  2. type Services.msc in the search box and click on enter.
   
  Note: the common addiction for "Remote Access Connection Manager" and 'Remote Access Auto Connection Manager' is 'Secure Socket Tunneling Protocol Service'.
   
  Make sure that you check the properties of service no matter what you try to start, then click the dependency tab and make sure that you select the dependency registered under this service services.
   
  The dependency of 'Remote access connection manager' services include:
   
  a. secure Socket Tunneling Protocol Service
  b. phone
  c. Plug-and-Play
  d. remote Procedure Call (RPC)
  e. DCOM Server process Launcher
  f. RPC end point mapper
   
  Make sure that you try to start the Connection Manager Service dependency services automatic remote access as well.
   
  Method 2:
   
  I recommend you to update the drivers and see if it makes a difference. You must be logged on as administrator to perform these steps.
   
  1. open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the assword or provide confirmation.
  2. in Device Manager, locate the device, and then double-click the device name.
  3. click Driver tab, then click on set to update driver and follow the instructions.
   
  Try to follow the link provided to update a hardware driver that is not working properly and check the question below.
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• After you download El Capitan, I received the following error message when you try to install: the drive is not formatted in MAC OS extended (journaled). Use disk utility to enable logging or reformat the disc. Can anyone help?

  After you download El Capitan, I received the following error message when you try to install: the drive is not formatted in MAC OS extended (journaled). Use disk utility to enable logging or reformat the disc. Can anyone help? (My disk utility shows that she in MAC OS extended (journaled) format.)

  It shows that it is Mac OS extended, not journaled. Click enable logging in the toolbar.

  The thing you read is if you format the drive using the RAID settings you have selected. You have to look at the bottom of the window where it shows the Format.

• When I try to print on a printer connected to my win7 I get code "printer not responding" 105-100003

  How to fix error code 105-100003

  I am running windows7 on my host network and vista on the other computer. I am able to connect to the correct internet on vista computer, but when I try to print on a printer connected to my win7 I get code "printer not responding" 105-100003. I printed before and I have not changed or added to any software since. Both computers are desktop computers and connected by ethernet cable. I have run diagnostics and checked all cables. I have a modem 2 son I had about 2 months.

  Hi, Jimmy.

  Make the printer and model would be useful.  Thank you.

  Try the following:

  If your printer is connected via a wireless network:

  1. Make sure that your printer is turned on. (Start button / stop is turned on).
  2. Make sure that the blue LED of Wi - Fi on the front of the printer is on and stays on.
     • If the blue wireless LED flashes, your printer is not connected to your router.
     • 1. Follow the steps in the configuration of wireless network Guide (named the network installation Guide, if your printer has Ethernet printer capabilities) to connect your printer to your router.
       2. If you are unable to connect the printer to the router:
          1. Turn off the power to the router, and then turn on the router
          2. Follow the steps described in the [wireless] Network Installation Guide once again.
          3. If necessary, see what should I do if I can't configure my all-in-one printer (including the connection of wireless configuration)?
  3. When the blue LED on Wi - Fi from your printer stays on (not flashing):
     • If the error ' printer does not "occurred while you have been setting up the printer:
     • 1. Open Software Center.
       2. Select the tools of the printer, and then select Printer Setup Utility (under Tools).
       3. Follow the on-screen instructions to set up the printer.
       4. Try to use the printer again.
     • If the error occurred after you completed the roll-out of your printer from Home Center Software:
     • 1. Make sure that the print queue is online.
       2. From your computer, click Start > settings > printers and faxes (or start > printers and faxes).
       3. Click on your printer.
       4. In the printer menu, make sure that use printer offline is not checked.
          NOTE: These steps may vary depending on your operating system.
       5. Try to use the printer again.

  If the error persists:

  1. Remove the printer from your computer.
     1. Select start > settings > printers and faxes.
     2. Right click on your printer, then click on remove.
  2. If your computer is WINDOWS VISTA or WINDOWS 7 OS, turn user account control.
     1. Select start > Control Panel.
     2. Double-click user accounts.
     3. Click turn user account control on or turn it off.
     4. Select the check box use user account control.
     5. Click OK.
  3. Configure the printer again.
     1. Go to start > programs > Kodak > Kodak Printer Setup Utility.
     2. Follow the on-screen instructions to set up your printer.
  4. Try to use the printer again.

  If the error persists:

  1. If you have updated to the Home Center Software v6.x or greater, disable the Hello Service.
     1. Select start > run.
     2. Type services.msc in the box, and then click OK.
     3. Locate and right click on the Hello Service and select Properties.
     4. Since the "Startup type:" drop-down list, select Disable.
     5. Click OK.
     6. Locate and right click on the network AiO Kodak Discovery Service, then select restart.
  2. If you configure your printer, run the KODAK printer setup utility.
     1. Select start > programs > Kodak > KODAK Printer Setup Utility.
     2. Follow the on-screen instructions to set up your printer.
  3. Select the Hello Service.
     1. Select start > run.
     2. Type services.msc in the box, and then click OK.
     3. Locate and right click on the Hello Service and select Properties.
     4. Since the "Startup type:" drop-down list, select automatic.
     5. Click OK.
  4. Try printing from the center of renovation again.

  If the error persists:

  1. Make sure that any firewall software blocking the required services and that it does not block the firewall of the router. See cannot use a wireless printer to computer on the same network with firewall security program.
  
  NOTE: If you use BitDefender Total Security 2010, the problem can be solved by turning on the game mode in the firewall. If it does not turn on the game mode, temporarily disable the firewall to enable wireless printing.
• Make sure your computer is not connected to a virtual private network (VPN) or wireless home another network of safe working when you use the printer on your network. See using printer with the virtual private network (VPN).
• Check that your printer is not connected to the network trouble with the same name (routers with the same default SSID in your area). It is common for users to keep the value by default, out-of-box, SSID as the manufacturer provides (for example the linksys). If your router still has the default SSID, change the SSID under a new name specific to your router.

NOTE: updated to the latest version of the firmware of the printer and the software when prompted will help you have the most reliable connection possible. Go to www.kodak.com/go/aiodownloads.

If the error persists, contact us.

http://support.en.kodak.com/app/answers/detail/A_ID/36674/selected/true

• Remote Access Connection Manager

  What is Remote Access Connection Manager and what is it?        PS. I don't know what Windows topic category and applications, this falls under, but since I HAD to choose one...  Thank you for your help.

  Hi bjeja,

  Welcome to the Microsoft community where you can find all the answers related to windows.

  Remote Access Connection manager manages connections dial-up and virtual private network (VPN) from the computer to the Internet or other remote networks.

  If you have questions about Windows do not hesitate to answer and we will be happy to help.

• Error when you try to download the application forms, not a valid Windows 32

  not a win32 application invalid and stop the download

  When I try to download tax forms IRS my computer says "application not valid windows 32 and stops downloading just 15 seconds before its filled! What the heck is wrong?

  Hello shelleyjane,

  Get the error: not a valid 32-bit application can have several origins:
  I have listed some of them below, and possible solutions.

  The file is corrupted, bad or missing.
  -If the hard disk is damaged or hurt it cause work programs to fail, either because not all data can be read from the hard drive the program is damaged on the drive. Run scandisk and defrag on the hard disk to check for potential errors.
  -If you run the program from a shortcut on the computer, verify that the program is still on the computer. In some cases if the program is no longer installed on the computer, you can get this error.
  -You can download the app again and see if you still get the error message.

  File is not designed for your version of Windows:
  -If you try to run a program that is not designed for your version of Windows, you can get this error.
  -Although many old programs designed to work in older versions of Windows will work with new versions of Windows, unfortunately, not all programs will not work.
  -If the program is an MS-DOS program more former start program or Windows, you can get this error.
  -If the program is designed for a 64-bit version of Windows and you are running in a 32-bit version of Windows, it will not work and generate this error.

  File is a virus, worm or other malicious program file.
  - This error can be generated by a file that is a virus, worm, Trojan horse or other type of malware file. Often, this will result because the antivirus installed on the computer will not allow the file to install or run. Try to analyze the file to check, it is not a virus or infected.
  -If the file has been checked and is clean, it is always possible that the virus protection program or a another program installed on the computer is at the origin of questions during installation or execution of the program. Start the computer in Mode safe and try to run the program. start the computer in Mode safe will be that nothing is running in the background that could cause this problem.
  
  Hardware incompatibility.
  -If you get this error during the installation of a program, it is also possible that the CD-ROM drive or the drive that you are installing the program from is not compatible with Windows or has drivers that are not compatible with Windows.
  -Download the latest drivers for your CD player or other of the manufacturer of the computer or the manufacturer of the equipment. (Microsoft does not pilot for other materials)

  Let us know if that helps.

  Marilyn

• Acrobat and Reader 8.  When you try to print, the memory could not be "read".

  A user (without local administrator rights) does a job batch of Microstation and exported all his drawings in pdf format.  They open correctly in Acrobat 8 and Reader 8.  When he clicks on the button print, it gets the error below.  When I login with local administrator rights, I can print these accurate pdfs very well.  Here is the event/error log entry.   Any help would be greatly appreciated.   It runs Windows XP SP3.

  Event type: Information

  Event source: Application Popup

  Event category: no

  Event ID: 26

  Date: 27/03/2012

  Time: 17:27:46

  User: n/a

  Computer:

  Description:

  Application popup: 2012-03-27 C6-01. PDF - Adobe Acrobat Professional: Acrobat.exe - Application error: the instruction at "0x0436959a" referenced memory at "0x00000d28". The memory could not be "read".

  Click OK to terminate the program

  Click on CANCEL to debug the program

  We tested with another nonadministrator account and Acrobat worked fine.  Therefore, the problem was in the user's profile.  We just its data saved, deleted the old profile and did reconnect.  This has created new profile.  Acrobat works beautifully.

• When you try to add a printer, get error Printer Spooler service is not running

  I lost my printer and when I click Add printer, I get the message of this operation could not be completed. The print spooler service is not running. Then, the computer detects the new hardware and says the RPC server is unavailable can help?

  Check the status of 'Print spooler' & RPC (remote Procedure Call) services in the services window. You can check the link below to change the status of the services.

  http://TechNet.Microsoft.com/en-us/library/cc736564%28WS.10%29.aspx

  After the services start, delete all previous printers. Uninstall the drivers and then try to reinstall the printer again.

  If the problem still persists to the print spooler, you can import the registry across the entry below machine & merge the machine to issue:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Spooler

  Also check out the link for your RPC unavailable problem:
  http://support.Microsoft.com/kb/242079

  Now, try to restart the print spooler new service & try to install the printer.

  Note: instead of copying files from another machine you can also run the SFC/scannow.

• I change my motherboard, I do not change anything else in my computer I have xp professional window, when I power my computer, the computer will not start, it asks me to insert the cd and press ENTER, I don't have the xp cd, help me please.

  install a new motherboard in my computer, I need the recovery cd to start the computer, I have Windows xp?

  Assuming that you are XP is already installed (you do not specify) and the old IDE hard drive, you may need to enable the IDE in the BIOS of the motherboard.  Sometimes on systems more recent IDE is disabled for SATA.  Other than that, I don't know.  Find a friend who has an XP Pro CD.  How is that you have it installed but do not have the CD?  If it was a computer OEM like HP, Dell, etc, then you should contact the manufacturer for a restore CD, but since you have changed the motherboard, it is possible that they won't support you more, unless it is a replacement of the factory.

• When you try to share my internet wireless connection I get this errordependency service or group was able to start

  When I try to share my internet connection, I get the following error. dependency service or group was able to start

  Hi Jason,

  1. What is the brand and model of the computer network adapter?

  2. How did you try to share the internet connection?

  Maybe not all services that run the Internet (ICS) ICS are enabled. I suggest you make sure that the slot addiction services are enabled.

  a. Click Start, select run, type services.msc and click OK.

  b. to activate a service, look for it in the right pane, double-click its entry.

  c. do not forget its Startup Type is set to automatic, and then click OK.

  All the following services must be so configured to use ICS:

  Application Layer Gateway Service
  Network connections
  Knowledge of the network (NLA) locations
  Plug-And-Play
  Remote Access Auto Connection Manager
  Remote Access Connection Manager
  Remote procedure call (RPC)
  Telephony

  After checking and automatic startup for each of these services configuration, close the Services window and restart the computer before trying again to enable ICS.

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• Error 711; Remore access connection manager service will not start

  Error 711; Remore access connection manager service will not start

  Hello

  Thanks for posting your question in the Microsoft Community!

  When exactly do you get the error message?

  This error message appears when a required service is not started on your computer. You won't be able to connect to a network, and you might not be able to install network cards.

  This problem may occur if some or all the following services are not started:

  • Plug-and-Play
  • Remote Access Auto Connection Manager
  • Remote Access Connection Manager
  • Telephony

  You can see test link following the steps and check:

  Get help with "Error 711" message

  http://Windows.Microsoft.com/en-us/Windows7/get-help-with-Error-711-message

  Do not post the State of the question.

  You can always view in Microsoft Community if you need help with Windows.