When my DVD drive would not work, I bought an external. I get the same message when I go into properties. Pilots have been disabled.

Similar Questions

• CD/dvd drive does not work - it is recognized when the computer starts, and it is listed in the Device Manager?

  I am running Vista Home Premium on a laptop Compaq Presario F700. It is listed in the list of computers of readers, it is listed in Device Manager. The lites drive that the computer boots so I know it is detected. When you run itunes or media player the player does not open. When I push the drive button it will not open. It opens with a paperclip in the exit hole. It cannot read a CD or a DVD. None of the media players even recognize there is a disc in the drive. I tried to run fixit, but it would not drive either. I tried restoring from a previous backup, without change.

  Hello

  Check / settings (BIOS/CMOS) often F2 so watch the screen as it starts - place CD/DVD
  1st in the boot order (remember to put it at the time where the fact).

  Then put in a DVD to boot Windows and see if the driver works.

  If it doesn't then it's a hardware problem.

  =======================================

  If the drive has worked in the test above, that these can help:

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• CD/DVD drive does not work after 8 Win instalation

  Since a month since I've updated my windows in windows 8, everything works fine but the DVD - RW.

  When I put the blank cd and try to open it, it gives me error when opening by saying:
  "windows could not complete the format".

  Who's a software or a hardware problem?

  waiting for help!

  This means that your CD/DVD drive no longer works and is not recognized by the system?

  If Yes, then I would recommend checking this Toshiba document that I found on the portal of the knowledge base site:

  + Why my CD/DVD drive does not work after upgrade to Windows 8? +
  http://APS2.toshiba-tro.de/KB0/FAQ2B03F10002R01.htm

  You must uninstall the programs from Toshiba:
  TOSHIBA Recovery Media Creator
  TOSHIBA Disc Creator

• Satellite 2430: CD/DVD drive does not work - i/o error

  Hello all Toshiba people.i have recently bought a Toshiba Satellite 2430 for a very good price. One thing the carpet * a DVD - ram Uj - 810 drive does not work when I put in any type of cd or dvd, I get this error
  F:\ is not accessible.
  The request could not be performed because of an i/o error.

  I talked to my local computer Wizz and does everything that he suggested to the letter and still the same problem. He suggested updating the bios drivers and the only way to do that is on a disk drive that she cannot take the an or a CD or dvd drive is not working. Can you please help me!

  Begging you a lot
  Michael Borger

  In my view BIOS update will not change.
  I assume that the reader has worked in the past with the same BIOS version
  It is a drive hardware problem or some registry keys are corrupt.

  I think that it s a hardware malfunction may be a matter of lenses.
  But try this;
  Remove the drive from Device Manager and shut the laptop computer. After restarting again the operating system should recognize the drive again. Then you can check the functionality.

  Otherwise, you can remove the disk from the laptop, and then start the laptop without the drive. Then stop the laptop, put the drive in the notebook and start over.
  The firmware should again loads.

  But if these procedures help t, I don t see it differently as for replace the drive

• Satellite A200 - 19L: no sound after hibernation & CD/DVD drive does not work

  First of all, my laptop computer became very slow loading vista after formula 1 week to buy it.

  Second, sometimes when I put the mode 'sleep' a revival of the laptop, there is no sound and a red circle appears over the speaker icon in the bar of tasks, and when I go into control panel > Sound, he tells me that no. his drive was installed and when restarting the laptop the problem resolved?

  Thirdly, after the formula of the week 3 buy the computer also dvd - cd player has the same problem, like the sound and when you open my computer that NO cd\dvd drive icon and when I put a cd or dvd, it does not work or run and it happens all the time, even if the laptop restarts.

  Since then im able to watch movies or work.

  I'm lost and I don't know what to do!
  (Sorry for my bad English, but I hope you understand the problems)

  Hey Osama

  I think I can help you. The questions that appear on your laptop are not serious and the only one associated with software or registry.

  Regarding your noise problem:
  Please check this Microsoft document
  http://support.Microsoft.com/kb/929685/en-us
  or
  http://support.Microsoft.com/kb/937077/

  the MS update must be downloaded and installed ;)

  Regarding the missing CD/DVD drive;
  I think you should try to remove the drive from Device Manager and reboot the laptop. Then the operating system should recognize the STRANGE again.
  Secondly you should access the registry editor and should remove the upper filter and bring back the key filter
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Contro l\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  Recommend checking out:
  http://support.Microsoft.com/kb/270008/en-us

  best regards and I hope that I can help you

• I have a Dell Inspiron 1525. The player/cd-DVD drive will not work. The help section it says it is (code 10). The drivers seem to be installed. Can you help me please? Operating system is Windows Vista Home Premium

  I tried the support centre and followed their advice, but no luck yet.

  Hello

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  Please make all below even if you have done some before as it is often the set of operations which solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack.

  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• E CD/DVD DRIVE DOES NOT WORK

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: I am IMPOSSIBLE to GET THE DRIVE E (CD/DVD) TO READ. WHAT CAN I DO TO GET THE PLAYER TO WORK?

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• CD/DVD drive does not work error Code 19 a dI have tried all the solutions of correction that I can find.

  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I tried Mr. Fixit, and I still keep getting the same message again and again... It was working fine, less then a month ago.

  Hello

  19 code means there is a driver conflict such as two devices attempt to use the same resources.

  Please make all underneath the same if you've done it before as it's often the total of the process which
  solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.

  Normally the above will solve this problem if not work your way down through them, even if you
  done before.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  --------------------------------------------------------------------------------------

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• My CD/DVD drive does not work

  My CD/DVD drive does not work, he plays any kind of disc, I don't think that my computer recognizes that it has a DVD player that more, please help!

  See this knowledge base article http://support.microsoft.com/kb/982116/en-gb

  Remove spyware, etc., can often mess up some registry settings that make it seems that the CD / DVD ROM drive is defective.
  HTH
  Neil
  www.nwarwick.co.UK

• How to create a bootable Windows Vista USB drive? I can't install Windows Vista with a disk because my dvd drive does not work.

  I have install vista and I want to convey in the USB key... because my dvd drive does not work... Please tell me what I need to do

  Please send your reply to my email id, or post it here...

  Hello

  Vista is not designed to be installed like this.

  But others led to ways to do so.

  This may interest you on this subject:

  "How to create a USB of Vista Installation key '

  http://www.Vistax64.com/tutorials/181538-USB-bootable-Vista-installation-Flash-thumb-drive.html

  Google will help you in this matter.

   

  See you soon.

• I bought Adobe Lightroom 6 only to see my DVD drive does not work with Windows 10.  Is it possible to download Lightroom?  I have the DVD with the serial number.

  I bought Adobe Lightroom 6 only to see my DVD drive does not work with Windows 10.  Is it possible to download Lightroom?  I have the DVD with the serial number.

  Download and install the trial version of Lightdroom CC.

  Then enter your serial number, follow these steps

  How to convert a trial CC 6 Lightroom Lightroom

• Bought LR6 DVD but the installer does not connect to the internet for I can register it.  I downloaded the trial version to work around this problem, but I can't get the program to start.  I get the same message that I should connect to the internet and c

  Purchase DVD LR6 Adorama, but Setup does not connect to the internet so that I can record.  Internet works fine.   I have Adobe account.

  I went to Safari to Chrome and downloaded the trial version in the hope to bypass the DVD version, but I can't get the program to start.    I get the same message that I should connect to the internet and connect.  It seems impossible after 3 hours.  Spent an hour chatting with the support of the India.

  Also remove the cookie file and reg Lightroom then enter the serial number and check.

  Windows:

  Press Windows button (located between Ctrl and Alt buttons) with the key R together at once, you will get a command window.

  Type below command and press the enter"" key.

  programdata %

  It will open the ProgramData folder. inside locate Adobe folder.

  Go to Adobe > Lightroom.

  Open Lightroom and delete all the files inside,

  Then run LR 6 and enter the serial number,

  Mac:

  (1) right-click on the icon in the Finder, then select the 'Go - To Folder' option.
  (2) you will get a text box, type in the following command and then press the 'return '. (" Do not miss ~ symbol" "')

  ~/Library

  It will open the folder of the user's library.

  (3) then navigate to Application Support > Adobe > Lightroom.

  Open Lightroom and delete all the files inside,

  Then run LR 6 and enter the serial number,

• When I try to copy files to a CD, I get message "Windows has a problem to copy this file to a CD." How to fix? I get the same message that I click on "Copy to CD" or drag the file to copy to the CD player.

  When I try to copy files to a CD, I get the message "Windows has encountered a problem when trying to copy this file."  I press the button "Retry" without any result.  I get the same message that I have click on 'Copy' files on a CD or drag the files to copy to the CD player.  I was able to copy these same files to a CD a few days ago.  Thanks for the suggestions.

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  1. don't you get an error code along with this error message?
  2. what CD burning software is installed on your computer?
  3. what kind of CD do you use to burn?
  4. What is the status of the CD - DVD drive in Device Manager?

  Method 1.
  Let us first check the status of the optical drive in the Device Manager. Check if there is no error code or yellow mark is listed.
  Reference:
  Explanation of error codes generated by Device Manager in Windows XP Professional
  http://support.Microsoft.com/kb/310123

  Method 2.
  If the problem is to start the computer in a clean boot state and check if you are able to accomplish this task.
  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I can not load a CD rom. I get the error message is that the CD rom is 16-bit and my Vista 64 Bit.__What are solutions to make this readable CD Rom in my system.

  I can not load a CD rom.  I get the error message is that the CD rom is 16 bits and my Vista 64-bit.
  What are the solutions to make this readable CD Rom in my system.

  It seems that if the CD is read correctly, but if I interpret your message right, you have problems to install the software.  And if the facts are that it is a product of 16 - bit and Vista is a 64-bit operating system, you won't be able to install it.  Support for older, 16-bit software was removed from Vista and Windows 7.  You would need to consider using a product such as Microsoft's Virtual PC or VirtualBox from Sun Microsystems virtualization to run - and if it were a game, same virtualization may not work.

  'Herb Ellicott City' has written in the new message: * e-mail address is removed from the privacy... *

  I can not load a CD rom.  I get the error message is that the CD rom is 16 bits and my Vista 64-bit.
  What are the solutions to make this readable CD Rom in my system.

• When opening 2014 CC PS I get the message "the program cannot strt because ONCoreFoundation8.dll is missing on your computer. Try reinstalling the program to fix this problem.  I did and still get the same message.

  When opening 2014 CC PS I get message "the program can't start because ONCoreFoundation8.dll is missing on your computer. Try reinstalling the program to fix this problem.  I did and still get the same message.

  I have no errors during the installation process.   I have now gone PS cc, copied all the files with ONCore - and paste in the location of the same file in 2014 CC PS.  There is now no error report when I run CC2014 PS and everything seems to work properly.

  I'm still not sure why Adobe has PSCC2014 rather than an update on PS CC.