When the pc is a sleep he doesn't.

Similar Questions

• Dv6 7000: charging does that when the lid is closed (sleep mode)

  I have a laptop HP DV6 7000. The battery doesn't work that when the lid is closed (sleep mode).

  If I close the lid and plug in the charger, the light indicates orange and the battery will deliver to load almost full.

  If I open the lid before the orange light changing to white, battery icon always says: _ % available (plugged in, does not support).

  Several different Chargers give identical results. EACH of them is fully charge the battery in two hours; as long as the cover is closed. If I open the lid, even to say 50% load, the orange light glows white and the battery icon always says: _ % available (plugged in, does not support).

  Thank you, Ed.

  Hi @ElyMayor

  Thank you for your response.

  The last thing I can suggest to try a restore to factory.  Performing a recovery of system HP (Windows 7)

  While the recovery, there is an option to backup your personal files. If you have not already done so, it is now a good time.

  Restore files that have been supported to the top using HP Recovery Manager (Windows 7)

  Alternatively, you can contact HP support for assistance. They can access your system remotely to help alleviate the difficulties.

  Please contact our technical support at 800-474-6836. If you do not live in the United States / Canada region, please click on the link below to get a number of assistance for your region.

  World wide phone holder

• time machine updates when the iMac is in sleep mode

  Should I stop using energy saver, when is my time machine backup. In the past, I noticed that when I was copying files copying stopped when the machine went to sleep snd started again when I woke the machine.

  What is there to back up on your computer when it is ' sleep?

  I put my iMac to sleep every night.  Never a question of backup w/Time Machine because there is nothing to back up!

  

• Music on iOs 9.2 playback stops when the phone goes to sleep

  I get a lot of e-mail music files.  I used to be able to read the files, leave email and use other functions, and could still play music.  Now when I go out of the enamel, the music stops when I upgraded to 9.2

  So, I listen to music from an e-mail and hung up and when the phone "goes to sleep" music station.  It didn't happen before 9.2.

  Please fix this.

  I have the same problem. In my case, the music also stops when I get out of the e-mail application.

  Please, how to fix?

• Continue to application play when the device goes into sleep mode

  Hey guys,.

  wondering if anyone knows how to maintain an active application when the unit goes into fashion watches?

  My application needs continue to work when the device goes into sleep mode if he went in that State by itself, or if the user put it to sleep.

  Yes I tried it on a physical device. It works, I promise you

  To clarify, here is what you will see when using KEEP_AWAKE:

  1 device shall not sleep when the application is currently active

  2. the device shall not sleep if the application is reduced, and you are in mode carousel

  3 device WILL sleep if the user switches to another application and full screen.

  In addition, another thing to know, if the unit is not assigned to the showcase mode, which is not by default, the audio stops when the user leaves your app. This is not related to sleep and is totally out of our control, but could be a good thing to add to your product details.

• Will be that the download stops when the computer goes into sleep mode?

  Will download, install, or all these action stops when the laptop goes to sleep.

  MK

  Yes, it will be.

• X carbon 1: after open the cover in mode 'sleep' it doesn't wake up

  Dear all

  power option is implemented in sleep when I close the lid and after opening it, he did not wake up. I have to press the power button for 5 seconds about to reboot the system

  I use windows 8

  Help, please...

  Thanking you in advance

  Asher

  The same problem with my 20 has 7. Lenovo said machine is DOA and I should have the motherboard replaced (they have no respondent relly on that much, technology has decided that, in 1 minute).

  That's what I discovered when I went to install Win7 to a factory condition: I has nothing to do with the power manager; the problem persists with the PM old or newer version. When it is plugged into the internet connection wired and wifi not activated - sleep and Awakenings are solid as a rock. When WiFi - reproducible gel mode "sleep".

  Run the utility of the Lenovo software update and install optional install WLAN Intel 17.12.0. Or check in your control panel to win if you have the Intel "Proset/Wireless Software 17.12.0 already installed. This update fixed the problem for me. But I have not any 3rd party software turns yet, so I can't say that this is the final solution.

• iPad Hotspot stops when the ipad goes to sleep!

  I have an iPad unlocked and locked iPhones.  When I go on a trip I put a sim card in the iPad and use the hotspot service for my iPhone to connect to the internet. The problem is the last time that I did two years ago and at that time there in iOS 8 every time the iPad fell asleep the hotspot goes out.  The only solution I found was to disable the "sleep mode" the ipad and stop the brightness all the way down.  This drained the battery on the iPad quickly because even with low brightness, the screen is activated.  Someone came up with a better way to do this with an iPad or is this problem fixed in iOS 9.2?

  Joe

  Hi there Joe_Dawson,

  I see you want to save a the battery life on your iPad while using Personal Hotspot by disabling your iPad screen. One way to do would be to use a function of accessibility called screen curtain to your goal:

  Turn on or off the screen curtain. Triple-tap with three fingers. When the curtain of the screen is enabled, the content of the screen is active even if the screen is off.

  Use iPad with VoiceOver - iPad User Guide

  http://help.Apple.com/iPad/9/#/iPad9a24752e

  Thank you for using communities Support from Apple!

• Yoga 2 Pro advertising plays when the computer goes to sleep

  Hello, so I recently bought a Yoga 2 Pro and have almost no complaints. One small thing I noticed is that my computer from time to time upon entering the mode "ensure" with the lid open, instead of displaying a black screen as planned will instead show an advertisement stating "4 NEW MODES, LENOVO YOGA 2 PRO" and will begin to show a video advetisment.

  I would rather the computer make a traditonal sleep mode when the lid is left open, how can I disable this advertising? I tried to play with the sleep settings in windows, but not luck. This occurs when both on battery and plugged in. I also tried to uninstall the software of Lenovo's Transition, but that did not help. Any ideas? It seems that the computer may be in demo mode? Thanks for the help.

  Good afternoon and welcome to the community.

  This is the default screensaver.

  To change it, right-click on the desktop, select Customize, then select the screen saver at the bottom right. You can then make changes in the window that appears.

  I hope this helps.

• Windows wireless service turns off when the computer goes into sleep mode

  Windows 7 64 bit, HP DV4 laptop. Was working fine until the update of adobe reader may also have a windows update. Have since been uninstalled adobe reader software and reinstalled. Updated the qualcom wireless driver.  WLAN keeps logging service when my laptop goes to sleep. I can restart with services and it works again. Autoconfiguration WLAN service is set to restart the service for 2 trys.

  Hello

  . You receive an error code or message?

  Please follow the methods and mark the question below:

  Method 1:

   

  You need perform a clean boot to prevent possible ask contradictory from interfering with your computer.

  To put the computer in a clean boot state, you must follow the steps in the article mentioned below.   How to solve a problem by performing a clean boot? : For more information on the execution of clean boot, follow the link.

  http://support.Microsoft.com/kb/929135

  Note: You must follow step 7 of the article mentioned above to recover the computer to Normal startup after you complete all the steps.

   

  Method 2:

   

  Using the troubleshooter from network in Windows 7:

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

   

  Method 3:

   

  Why am I disconnected from my network? :

  http://Windows.Microsoft.com/en-us/Windows7/why-am-I-being-disconnected-from-my-network

   

  Method 4:

   

  Wi - Fi and in Windows network connection issues:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  I hope this helps.

• My computer is connected to a router via ethernet but my wifi stops when the computer goes to sleep. How can I stop this?

  I just installed the router today.  Wifi a works fine until the computer goes to sleep, then my wifi for my Ipad, nook etc off.  This should not be the case.  Why would he do that?

  Hello

  1. have there been recent changes to the system before the show?

  2 is the issue limited to Wi - Fi?

  Method:

  Follow these steps and check if that helps.

  (a) click Start, type Device Manager in the search box.

  (b) click on Device Manager , according to the results.

  (c) expand the wireless adapter, right click on the drivers listed.

  (d) click on Properties, click on the power management tab.

  (e) uncheck the option allows the computer to turn off this device to save power.

  (f) click apply, click OK.

  Let us know if it helps!

• 64 bit Vista crashes when the system goes into Sleep Mode. Have cold start. Simultaneous began with the June 8 patches.

  This problem started a week ago, say at the time of the June 8 fix release. I think the relevant in case the log message is 'detected bad event COM + a system code back during internal processing. HRESULT is C 8007043 line 45 of d:\longhorn\com\Complus\src\events\tier1\eventssystemobj.epp. Error report, please contact Ms Product Support Services. "However, when I contacted MS, they would not help without paying the fees because it was an OEM installation. The system remains upward after the stabilization of the system going on in SafeMode after cold start, close and then switch to normal mode. However, once launched, it seem (ed) as the hard drive light was permanently. I did a restore to June 8, most early I could continue.  The hard drive worked without interruption after that.  I did a forced sleep and restart and the system froze again. With this in mind, I wonder if .NET patches that were released were running somehow at the time of sleep and that he could not recover.  OR, during sleep, the system was made of updates and the system has been disabled, corrupting the updates.  I looked at the Windows Update settings and it has been set to automatically install updates.  It is quite possible that the user did not know and did not recognize there are pending updates.  Maybe updates were not correctly packed in order to manage a system from going into Sleep Mode, while they were installing. In any case, any who would provide help on how to identify the problem and fix it.  There may be registry entries need to be corrected?

  Duane G. Leet, Ph. d. 45 years of experience in technology

  Microsoft support has provided a solution.  Here is the procedure:
   
  We can run reset Windows Update Tool and system update tool to detect incorrect manifests, files or data from the registry. Please follow the steps below.
   
  Step 1: Launch the tool to reset Windows Update and the update of the system tool
  ====================================
  1 download and run reset Windows Update Tool from the link below:
   
  http://go.Microsoft.com/?linkid=9665683
   
  2 download and run the update tool of the system from the link below depending on the Type of system:
   
  Update for Windows Vista 32-bit system tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=b4d90b06-c27d-4483-bc1f-04d43fa7b293&displaylang=en
   
  Update for Windows Vista 64-bit system tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=f6f353c0-d00e-43e7-97EF-0feefc7ff064&displaylang=en
   
  Note: It may take an hour or more time to detect and replace the erroneous data, please be patient. When it is finished, restart the computer and reinstall Windows Vista SP2.
   
  If Windows Vista SP2 can not always be installed, I suggest to download the stand-alone Installer and install it in clean boot Mode.
   
  Step 2: Download the installer of Windows Vista SP2 Standalone
  ===========================================
  1 download the installer of Windows Vista SP2 Standalone from the link below depending on the Type of system:
   
  Windows Vista Service Pack 2 - version independent ALL languages for Windows Vista 32 bit (KB948465) (475,5 MB)
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=891ab806-2431-4D00-afa3-99ff6f22448d&displaylang=en
   
  Windows Vista Service Pack 2 - version independent ALL languages for Windows Vista 64 bit (KB948465) (745,2 MB)
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=8ad69826-03d4-488C-8f26-074800c55bc3&displaylang=en
   
   
  Step 3: Install Windows Vista SP2 in clean boot Mode
  =========================================
  Please disable all startup items and services of third parties at boot to avoid conflict when installing Windows Vista SP2.
   
  1. click on 'Start', type: MSCONFIG in the search box and press ENTER.
   
  Note: Click 'Continue' if the "User Account Control" window appears.
   
  2. click on 'Services', check "Hide all Microsoft Services" and click on 'Disable All' (if it's not gray).
  3. click on 'Start', click 'Disable all', click 'OK' and restart the computer.
   
  Note: Disable temporarily the startup group only prevents the start up programs from loading at startup. This should not affect the system or other programs. We can manually run these programs later.
   
  4. double-click the downloaded standalone installer and follow the instructions to install Windows Vista SP2.
   
  To restore the computer to a Normal startup, repeat step 1 above. Then click "Normal startup" in the general tab, click on "OK" and restart the computer.
   
  If there are any questions or concerns, feel free to let me know. It is my pleasure to be useful.

  +++++++++++++++++++++++++++++++++++++++
  The cause was not determined, but evidence tends to a disturbance in the download or installation process, with one of the errors in the event log is an error in checksum on one of the modules. With a large file, 745 meg, the mean time to failure on a LAN network is probably shorter than the download time.  The installation process was probably longer than the time that the system has increased...  Corrective actions for Microsoft could include more small download / install, not allowing an automatic installation for automatic download over a certain size, or deal with the best controls during installation to intercept the checksum error.  Duane G. Leet, Ph. d. 45 years of experience in technology

• iPhone not charging when the Mac is in mode 'sleep'

  Before the OS X El Capitan 10.11.6 version update, I was able to charge my phone while my Macbook Pro was in mode 'sleep' / with the lid closed. Since the update to the latest version of El Capitan, the power to the USB ports immediately turns off when the laptop goes to sleep. Is it possible to fix this?

  Try a different USB port. There is only 1 USB port can charge the iPhone when the lid closed.

• PC goes mode sleep when the Power Options are set for ever, etc. also can not wake up

  Hi, I read the other posts on this topic, but my problem seems a little different.

  I am running Windows 7 on a Dell desktop computer and I tried to run chkdsk and also the Dell diagnostics that I have some problems hard drive; However, it gets so far and the pc goes into mode 'sleep' causing me even worse problems that chkdsk/diagnoses are halfway through a volume. The pc has done this on and off tension for awhile, but hopefully not when something critical is running, even if it is a nuisance.  I did all the steps recommended here as ensure my Power Options are set, etc., but he always does.

  In addition, when the pc goes to sleep, I can't wake him up by pressing the power button or any key on the keyboard.

  I've been in contact with Dell and they said that it's a software problem.

  Someone can suggest something else I can do (stop) the computer mode 'sleep' and also how to wake him.

  Thank you.

  Hello

  I'm sorry for the late reply.

  As you mentioned in your previous post, you wanted to know how to boot from the disc, I've provided the steps how to boot from the disc on my previous post. However, you can try to repair your windows using DVD for Windows 7 backup and check.

  You can see this Microsoft article below that will help you fix Windows 7.

  http://Windows.Microsoft.com/en-us/Windows/what-are-system-recovery-options#what-are-system-recovery-options=Windows-7

  Let us know if you need help most.

• Disable the lock screen sleeps but not when the computer sleeps.

  Hello
  My goal (and thousands of other users of Windows 8) are to save the batteries without be pestered constantly to enter my password - but at the same time to preserve the security of the computer.
  My goal is the following:
  -Screen could sleep in X minutes (to save power) without the computer
  -Lock the computer when the computer goes to sleep in X + Y minutes.
  I intentionally left the details that are not important. Please do not post a response unless you have been able to do successfully is Windows 8 - i.e. only requires a password when the computer goes to sleep, but not the screen.  It was no problem in Windows 7.  Is - this another Windows 8 'development '?
  X and Y are two positive integers. 8-)
  I expect an answer of reg-edit...
  Thank you

  Hello

  1 have had any changes made on the computer before the show?

  2. have you set any screensaver on your computer?

  If you have set a screen saver, I suggest you to follow these steps and check if it works:

  a. right click on the desktop.

  b. click on Customize.

  c. click on screen saver.

  d. in the new window, uncheck the option on the resume, the logon screen.

  e. click apply and OK.

  Let us know the results.