When you use the camera application, it will take two photos at the same time.  The first is in the shot, but the 2nd has movement, say a movement arm or head.  Weird.

Similar Questions

• Is cell required when you use the map applications of conduct?

  Is cell required when you use the map applications of conduct?

  Yes. GPS does not work with a Wi - Fi connection.

• DSC-WX150 will stop recording at 03:00 minutes when you use the HDMI video output

  Hello

  I have a Sony Cybershot DSC-WX150 camera.

  When using an output HDMI cable to view the camera to a television screen, the video movie recording function to 3:00minutes exactly every time automatically stops.

  When there is no HDMI cable plugged into the camera, it records fine 20 minutes.

  I tried changing film formats, changing the power settings, camera reset the values by default, etc., but with no difference.

  Why it only record at 03:00 minute exactly mark when you use the HDMI video output? Someone knows how to fix this?

  Thank you

  Hi tight,

  Welcome to the community of Sony!

  If I understand correctly, when you use your TV as a monitor while video recording automatically stops and does not cross the entire 29 minutes. Based on your manual, it is normal for the camera when it is connected to another device via the HDMI cable. This serves as protection for the camera.

  If my post answered your question, please mark it as "accept as a Solution. Thanks_Mitch

• When you use windows 7 or XP on my two computers will not allow me to attach picture files. Get an error message saying to see the details, but there is no detail.

  When you use windows 7 or XP on my two computers will not allow me to attach picture files. Get an error message saying to see the details, but there is no detail.  This has happened when I changed service providers

  When you use windows 7 or XP on my two computers will not allow me to attach picture files. Get an error message saying to see the details, but there is no detail.  This has happened when I changed service providers

  ===================================
  Try to visit the support site of your new service provider
  and search for instructions on how to set up your email.

• Why I get this message when you use the magnetic lasso tool: "WARNING: no pixel is selected to more than 50 percent."  The edges of the selection will be not visible. ?

  Why I get this message when you use the magnetic lasso tool: "WARNING: no pixel is selected to more than 50 percent."  The edges of the selection will be not visible. ?

  See here:

  WARNING: no pixel is selected more than 50%

• Loop Finder crash after upgrading to El Capitan.  'Finder close unexpectedly when you use the plug-in finder' - the message really is in Norwegian, so it may be different for the English operating system.

  'Finder close unexpectedly when you use the plug-in finder' - the message really is in Norwegian, so it may be different for the English.  The e is a compatibility issue with dropbox or Google drive in El Capitan?  Those are the plug-ins only that I could find.  Thank you very much.

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  Step 1

  For this step, the title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  In the upper right corner of the Console window, there is a search box to filter. Enter the name of the application crashed or process. For example, if Safari has crashed, you would enter "Safari" (without the quotes).

  Each message in the journal begins with the date and time when it was entered. Select the messages since the time of the last fall, as appropriate. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name, may appear in the log. Anonymize before posting.

  Step 2

  In the Console window, clear the search box, and then select

  DIAGNOSIS AND diagnostic USE information reports ▹ user

  (not diagnose them and use Messages) in the list of logs on the left. There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points downwards. You will see a list of reports of incidents. The name of each report begins with the name of the process and ends with ".crash". Select the most recent report on the process in question. The content of the report is displayed at right. Allows you to copy and paste to validate all of the content, text, not a screenshot.

  I know that the report is long, perhaps several hundred lines. Please report all this anyway. If the report is only a few lines, make sure that you have disabled the search box.

  If you don't see any report, but you know, he had an accident, you have chosen diagnostic and using the list of Log Messages. INFORMATION on the USE of DIAGNOSTIC AND choose instead.

  In the interest of privacy, I suggest that, before posting, you change the UUID ' anonymous, ' a long string of letters, numbers and dashes in the header of the report, if it is present (it cannot be). "

  Please do not post other types of diagnostic report - they are very long and rarely useful.

  When you post the journal excerpt or the accident report, you might see an error message on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• WHEN YOU USE THE CONSTRUCTOR OF MY SITE, I CAN'T COPY AND PASTE WROTE THE BROWSER SECURITY SETTINGS HOW TO NOT CHANGE THESE FOR ME TO COPY / PASTE?

  WHEN YOU USE THE CONSTRUCTOR OF MY SITE, I CAN'T COPY AND PASTE WROTE THE BROWSER SECURITY SETTINGS HOW TO NOT CHANGE THESE FOR ME TO COPY / PASTE?

  https://support.Mozilla.com/en-us/KB/granting+JavaScript+access+to+the+Clipboard

  This extension will help you implement the security policies for access to the Clipboard.
  
  Allow the extended Clipboard support:
  
  https://addons.Mozilla.org/en-us/Firefox/addon/852

• MainStage "lag" when you use the SPACEBAR as 'play '.

  Hi all, I'm relatively new to Mainstage (V3), and I'm hoping to use it for the first time this weekend to play the extra backing with a band tracks

  The issue I'm having, is that with the SPACEBAR of laptops on 'PLAY '. It is often "lag". or simply does not start the song. I have to wait a second, then hit again, it will work.  It is almost as if in Performance mode, when you use the down arrow key to select the next song, the 'focus' is on the list of patch, and if I click in the background where are playback buttons and stop, THEN that will work. I have not, however, been able to reproduce this particular behavior on a consistent basis.

  Everyone knows the same thing? Or why it is so 'all or nothing '?

  And a question important much donor... I gave all my reading titles to the waveform appropriate the other night (so I could visually see the waveforms above the attenuator as offers of backing track model), however, once I was moving songs in a different order, which stopped working. No idea why?

  Thnaks in advance

  About the offset by hitting the space bar, a thought occurred to me.

  How Mainstage allocates 44.1/16 bit wave files used in the reading plug-in? Which means, when a song is selected, which uses, for example, to separate the 5 cases of reading, one can assume that these audio files used in that song would need to "load" first.

  Anyone know if this is how Mainstage works?

• TestStand crashes when you use the feature of LENGTH

  So I have a problem when you use the TERM built on stage.

  the first time I run my sequence everything goes normally...

  the second time I try to run the sequence it freezes teststand.

  I have notices that when I run my sequence. I can see on TRACK OR the following:

  niSE_opensession

  niSE_connect (routex)

  nise_disconnect.

  but after that the sequence is complete. It is not close to the niSE sesion. that this has something to do with the gel TestStand?

  If this isn't the case, have you had this question before?

  I contacted pickering... they got me new drivers

  Response of Pickering:

  It sounds like the problem which came first when NEITHER Visa has been changed, version 5.2 or higher, I think. In any case, I'll try first to install the latest version of the Pickering IVI driver.

  http://downloads.pickeringtest.info/downloads/drivers/IVI/pi40iv_4.10.1.exe

  I installed them and it works now...

• When you use the NI-CAN Transmit sample receive the same Harbor; can a virtual CAN channel (RCA or 257) be used?

  I work for a company that produces and transforms electric parts. We strive to get in remission at nine of the ECU, experiences, Instrument clusters etc. I'm trying to learn how to use LabVIEW to write commands and read the data on the CAN bus. I have downloaded the NI-CAN driver. I am currently 'play' with the same reception Port.VI show in the basic frame of the finder example API folder OR. I am not able to send the number in the data to write the table that it be read by the ncReadNet Mult .vi. When I put the parameter to 'Pending entries reading' the ncGetAttr.vi returns a 0 to indicate that there are no frames to read. As a result, the Mult.vi ncReadNet does not run.

  I don't have any connected equipment, I use the virtual CAN channel CAN256. Is this the reason why I can't get data frames in my queue for the Mult.vi ncReadNet to read?

  When you use the NI-CAN Transmit sample receive the same Harbor; can a virtual CAN channel (RCA or 257) be used?

  CAN carry 256 and 257 are connected to eachother through software.  When you write about 256, you can read the data on 257 and vice versa.  I think the example you mention is a writing and reading on the same port, but what you want is to probably to make a copy of this VI, in order to run two at once, where it opens 256 and the other opens 257.  Then, when you write one that you will see on the other.  I think you might be able to use the test panel CAN too read an and use the example of the other.

• RunState.Sequence.Main vs RunState.SequenceFile? When you use the deployed software?

  RunState.Sequence.Main vs RunState.SequenceFile?  When you use the deployed software?

  Can someone explain to me why when I use something like->

  RunState.SequenceFile.Data.Seq ["Test Seq"]. Hand ["Test not"]. Result.Status

  the status will never be updated if I am set up for LabVIEW Run - Time Engine (but will work for the development of the system).

  Also why->

  RunState.Sequence.Main ["step Test"]. Result.Status

  Update for LabVIEW Run - Time Engine and development?

  I solved my problem with RunState.Sequence.Main ["step Test"]. Result.Status but I'm still curious why the reverse does not work?  Can someone give me please a validation test?

  Thank you very much!

  RunState.SequenceFile.Data.Seq contains the copy of time change sequences. These copies are not at all when running. At run time, a separate copy is made (and is accessible from RunState.Sequence) and only this copy of runtime is updated. These runtime copies are made for several reasons such as the following:

  (1) to ensure that changes to the sequence the runtime, do not affect the original version of the time edit of the file (you don't want to change the status to be an editing tool in the right sequence file?).

  (2) to support recursion, recursive calls in the same sequence have their own copy of the sequence so that State for a call is not crushed by one recursively calls the same sequence.

  There are probably other reasons as well, but these are probably the biggest.

  -Doug

• Need to reset the button by default when you use the structure of the event?

  When you use the buttons with a mechanical action "releasing lock" to only trigger the same structure with the same 'value has changed', the button does not jump upwards as you would expect.  I can get to behave as I want by adding a "default reset" invoke the node, but this seems somewhat exaggerated.  Is there an easier way to get the button to jump to the top after pressing on?

  The button will reset once it is read by the code. This means that the terminal is inside the structure of the event. If you move outside the terminal, it would read only the beginning of the race and then never and it will not be reset.

  If the terminal is learn the structure of the event, it is read by the code (even if it is not connected to anything) and it reset as soon as the event has a chance to run.

• When you use the touch pad, the pointer would not move.

  Original title: arrow not laptop computer movingon

  When using the touchpad on my laptop the pointer would not move so I had to plug my mouse to use my laptop. Why the touchpad pointer stopworking?

  Hi Ron123,

  1 Windows operating system you are using?

  2. What is the brand and model of your laptop?

  3. This occurs when you use a particular application?

  4. When did you start to question?

  5. did you of recent changes to the computer?

  You can try to update the latest version of the Touchpad drivers from the manufacturer's website and check.

  Updated a hardware driver that is not working properly

  Hope this information is useful.

• When you use the Windows XP Mode integration, it fails; maintains a new attempt and finally I have to cancel

  When you use the Windows XP Mode integration, it fails; continues to try again and finally I cancel it. The same newspaper for Virtual PC on the host computer has the following error message: Windows XP Mode integration error 'failed to connect in place inside the "Windows XP Mode" VM on channel 0 on the... named pipe endpoint XP, TCP port 3389 with the 0x8007274c error mode. This error occurs every time, but I don't know why he is successful a few times and sometimes fails. This question was in another post and mentioned the removal and resettlement components of integration, which I've tried, but it did not help. I also checked that I have the latest version of the integration components (v. 14.1.7600.16403). I have a separate instance of Virtual PC that I brought over my old XP machine and it was never a problem with integration. The problem with the image in XP Mode occurs also, regardless of whether or not the other Virtual PC image runs. Only the image of the XP Mode has this problem. I suspect it's perhaps a conflict of TCP port in the named pipe, but if so, I don't know how to solve. Thanks in advance to anyone who might be able to offer advice.

  Thanks for the reply. I tried to reinstall the integration features in the past, but the problem has come back at a later date. A few days after I posted this request for assistance, I needed to log out of Windows 7, so I hibernated the XP Mode image. Then, I opened a session in Windows 7 and thought I'd give it a try once again, and it worked this time! I did nothing special. So hopefully that will happen in the future, just as it went and on the past few months. Enjoyed your attempt to offer advice, however!

• Dreamweaver CS5.5 mac crashes when you use the background color palette

  Dreamweaver CS5.5 mac crashes when you use the background color palette

  Mac OS 10.11.3 El Capitan

  Hi bibledoc

  You can try to reset the Dreamweaver preferences.

  Following the file and the folder are removed from your system:

  / Users / your User Name/Library/Application Support/Adobe/Dreamweaver

  Rename the folder of Dreamweaver preferences, for example, Dreamweaver CS5.5 Old_Dreamweaver CS5.5 folder.

  / Users / your user name/Library/Preferences

  Rename the folder of Dreamweaver preferences, for example, Dreamweaver CS5.5 Old_Dreamweaver CS5.5 folder.

  Restore preferences in Dreamweaver CS4 and CS5, CS5.5

  Access the hidden library files Mac OS

  When Dreamweaver starts, it creates a new preferences file and the folder.

  If it helps doesnot, maybe you can try to create a new admin user account and check. If this is useful, you can try to uninstall and reinstall in the new user account.

  OS X Yosemite: set up users on your Mac.

  Kind regards

  Nikhil Gupta