White screen starts with Satellite P series

Similar Questions

• Collection with Satellite A200 series problem

  Hello

  I had problems at the start of Windows Vista. It does not run in any mode. When I try to recover (by pressing '0' to the screen, that nothing is happening).
  I used my recovery disks to restore the operating system. They run for awhile, and then a white screen comes up and it stops. Then I get PXE: memory, disk failure check cable.

  Finally, with some trial and error I could finally launch the recovery disks, when I try to recover with the factory settings it will stop with disc 2 does not end copy the files. Then I had to recover without recovery partition. After finishing, I found that it loaded Windows XP not Windows Vista. Where did Windows Vista go and how can get it back.

  Please someone help me with this problem.

  Thank you

  Hmmm... What Satellite A200 do you have exactly?

• Problems starting with Satellite P300 - 19K

  I have a portable Satellite P300 - 19K 1 month.

  Several times since I got it when I booted my system and got the password to logon windows my screen became a series of coloured horizontal lines and the Hung system completely. The only solution was to close by holding power button for 5 seconds. Screen start then on reboot that I would get in the trunk, but that did not work. Then, I learned that if I use the F8 key just I hit the power button I can get into a lot of upgraders and I was able to recover using the restore system but every time I lose a few programs that I need to reinstall.

  What has now happened 4 times in a month and becomes boring. I downloaded the latest display driver for the display of my card ATI Mobility Radeon HD 3650, but when I went to install it I learned the version I have on board is the same and everything is beautiful.

  Someone had something similar or have a solution?

  Hello

  If this happens with own pre-installed Vista (factory settings), please contact the nearest service provider and ask for help.
  Please do not test with some additional drivers. It WILL work properly with the factory settings.
  Addresses and phone numbers for ASP you will find under http://eu.computers.toshiba-europe.com > support & downloads > find an ASP.

  Good luck!

• Problem with the iPhone OS. Have to restore it several times and it now has white screen flashing with Apple logo

  Got my iPhone SE a little over a month since the Thailand of the Apple Store.

  First he couldn't restore entirely made from a backup so I had to delete all data and content then restored again. Then try to restore from a backup, still have problems (apps froze, failed to synchronize all of the apps, then tried to shutdown phone and glued on white background with the Apple logo).

  Try to third, I put my phone in recovery mode and restore as a new iPhone. All original content is now gone. Should it start again.

  Then small annoying problems occurred. For example, I could not find applications in the App Store, could not download new free applications, could not buy music on the iTunes Store app. It seems that Internet was frozen, when in fact it works always fine when try browsing on Safari. Facebook froze and could not push Home button to close App game graphics making static sound glitches but always disappear when him restart the application. Can't post photos on a social media application because my whole library of photos seems to be empty, when in fact he was always there. When I was taking pictures, the preview images were extremely blurry, and when checked in Photos app there is no trace of this photo that I took. I tried to close all the applications and open it again but the problem still persists. So I close the phone and restart it just to find that it stuck on the white screen with the Apple logo once more. Then, I took the phone to the Apple service provider. They restore the phone as a new iPhone for me and I had to start over once again. Only 4 days after this, my iPhone application suddenly found me a new unlock access code within 60 minutes without reason. I have to reset hard to solve the problem. And after that, the same day, my iPhone starts to blink on and outside and sometimes the white screen with the Apple logo appears.

  Whenever I said my problem of staff Support from Apple or the Apple service provider, they told me that it was a software problem. How can I when I do all these problems again and again from the beginning until now? Can anyone suggest me the right way to solve this problem? What problem do you think it's from? I can't take this anymore. I need a good show, not working iPhone undesirable. I can't keep it restore/reset/reboot over and over again like this. Please, help me.

  Sasawan

  You can watch some of my problems here on Youtube > >

  1 screen kept flashing white background with the logo apple and restart and turn off by itself. Sometimes I can go past lock screens, but it only last a few minutes, then it starts all over again > > https://youtu.be/tfygV57NmmY

  2 message when my phone push me to reset my unblocking reason code > > https://youtu.be/a_AKPWxfAfs

  3 static glitch sound on the Sims Freeplay game > > https://youtu.be/qw12RZ4yMqc

  Take it to an Apple Store for the assessment of the guarantee.  If you have restored to factory settings, and these problems persist, there is a hardware problem, no matter what you' re said.

• White screen on my Satellite A300

  Hi all

  My laptop Satellite A300 has suddenly stopped with a white screen, but I did not understand everything that I have done is force shutdown and restart again.

  It is not easy to say what was wrong there.
  You can now use your laptop without problem or this problem occurs again and again?

• White screen on my Satellite M34-S456

  -Do not know how - I managed to reload Windows XP Professional on my Satellite M34 S456.
  I got a white screen with a blinking cursor in the top left of the screen for days.
  Try of BIOS (via F12 F2 &) & kept getting the white screen).

  Now that is reloaded. How can I know what is the problem?
  And how can I prevent or fix?

  For example, if it is a problen w / my HARD drive (I'll buy a new HARD drive) vs my CD/DVD, etc...

  Any suggestions?
  I have a feeling that the problem is not resolved, & as soon as I stop I get the blank screen again.
  FYI-I think that put the HARD drive in the freezer for the night may have been key to get there surgery - seriously.

  > - Don't know how - I managed to reload Windows XP Professional on my Satellite M34 S456.
  > I got a white screen with a blinking cursor in the top left of the screen for days.

  This symptom of the computer appears generally if the master boot record (MBR) on the hard drive is bad or damaged.
  It may happen due to the mechanical stress of HARD drive.

  I had the same problem several months ago and solved using the command: fixmbr or fixboot

  Concerning

• MacBook pro 2 logon screen starts with no arrow cursor and must be restarted

  2014 Macbook Pro screen Retina 2 13 "opening session starts with no arrow cursor and must be restarted once every five tests.  When the computer reboots, message appears asking you if it must open programs that had started to load or cancel.  It is a recent problem that does not occur two months ago.  Once restarted, everything seems to be OK.  That is what it is?

  Try the start mode by holding down the SHIFT key at startup. Secure boot is quite slow because the operating system performs some cleanup and verification tasks, so give it time. Once you're completely connected, restart normally.

• Re: Failed to start with Satellite L300

  Hello
  I'm on a Toshiba Satellite L300 Windows Vista,
  I recently had my browser (Google Chrome) freeze so that the page that I was on was using Java.
  I went to reset, but once Vista began to start it would not go beyond the loading bar.
  Then, I went to boot from a drive to install Vista and met the same problem.

  I tried to start with the controller Mode SATA changed compatibility.
  This allowed the Vista disc load up successfully but did not allow for options but command prompt and from the Startup Repair.
  I ran Startup Repair twice and that Vista would load to the top of the loading bar then reset and loop this model.
  I don't know where to go from here, but any help would be greatly appreciated.

  Brad Winn.

  Hello

  Perhaps, your laptop is infected with the virus, and you cannot load windows. You can search and find a software like Kaspersky Anti-virus 8.0.0.506 Emergency Bootable CD and search for viruses. I wonder why you could not start Vista drive in AHCI Sata Controller Mode, I know the sata drivers are already integrated into Vista.

  Run "bootsect/nt60 ALL" into the command prompt, and then press ENTER. Wait and eject the Vista disc, reboot. Hope, it helps to have you tried to install from hard drive recovery image?

  Post edited by: jeka-Israel

• I can't start with Satellite P10 by pressing the power button more

  I can't start my Satellite P10 by pressing the power button more.
  Sometimes, very rarely its starts when I hold the power button for a while say 10 seconds.

  I tested the power supply and a battery to my friends P10 (of the same type) and both work very well.

  So it must be a problem with the key.
  No idea what to do?

  Thanks for any help

  The best.

  Tobias

  If it s a button or a power supply electronic problem, then you can't do anything.
  In this case assistance by the technicians of laptop would be necessary.

  But the next time that you should try this option if the laptop turns on not;
  Remove the battery and unplug the AC adapter from the laptop for about 30 min.

  After this short period of time to reconnect the two parts and check if the laptop could start.

  Good luck

• White screen powering a Satellite 1130

  I bought a second hand by Satellite 1130 laptop not too long ago and it worked fine for awhile but then it died on me... When I turn on the laptop the power light on the front comes on but nothing else. Laptop computer knows that it is on, as the DVD drive scans for a disc and the cooling fan starts but nothing else happens. The screen remains blank and I can't do anything with it. While he worked, I noticed when it has been turned on the the hard drive led on the front of the laptop used to Flash several times then it loads the operating system. THIS DOES NOT EVEN LIGHT MORE. This made me think it may be the hard drive that was dead, but told me that if that were the case, the laptop screen would have at least a cursor in the upper left corner of the screen and one would expect it a command to the user.
  ANY HELP WOULD BE APPRIECIATED...

  You re right. It doesn't seem to be a malfunction of the HARD drive.
  If the HARD disk is damaged, you will see a splash screen Toshiba or with a few s information on memory, CPU, etc, then he should try to boot from the HARD drive.
  In your case I think there could be a malfunction of the motherboard.

• White screen after the Satellite Pro P200 display driver update

  I installed the latest display driver ATI Mobility Radeon HD2600 (8.432, on the site of Toshiba through Tempo) on my Satellite Pro P200 yesterday. Reboot, everything seems good as much as the screen "Please wait...". "Windows Vista professional, but instead of showing the page of connection I get an empty screen (with a mouse cursor that moves around as usual). All I can do at this point is to be able to, and I'm running out of ideas on how to move forward.

  Things I've tried:
  # start in safe mode, the video resolution or last known good configuration, result the same screen empty.
  # connect to the system using remote desktop (to disable the driver) is not possible because the system has not yet loaded the network drivers.
  # I can't go back to a restore point because Vista can't find (I did a manual after you install updates windows over a couple of days).
  I can run a system command line options of recovery and prefer to use it to disable the driver + if + I knew how before the use of the more radical options.

  A search on the web (http://www.google.co.uk/search?q=ati+catalyst+vista+blank+screen&hl=en&sa= N) reveals that this has happened on a wide range of laptops with
  previous versions of the driver, but none of the links I've looked at to give a solution which does not exist for me.

  I agree with Hairyfool, you who should solve problems using an external display. If no image appears, then something with the material might be.

  Please give some information about your situation...

  See you soon

• A known issue with Satellite C855 series

  IM about to buy C855 - 2 EV, but I would like to know if theres a question with this kind of series such as heat problem or else.

  I don't know why I can't see my other post in the thread, I see only through my control panel

  Check this forum a little and try to find some discussions on Satellite C855.
  I put t think there should be a problem with it. Machine comes preinstalled with Win8 64-bit, so after the first start just to create your account and everything will be ready to use.

• Re: Don't start with Satellite C660D - 1C7

  Hello

  I was installing Windows 7 via the toshiba Recovery Wizard, but during the installation, the laptop freezes and I need to.

  When I start it up again, it shows ups two error messages:
  (1) PXE - E61: Media test failure, check cable of
  (2) reboot and select proper boot device

  Then I can't go to the Recovery Wizard (F8), it does seem that these messages. I disabled the lan on the bios. The first message disappears, but the second is still there. The hard drive is recognized by the bios and the bootsequence is ok.

  What I did:
  (1) reset the bios to its default value
  (2) try to install with a win xp cd, but it hangs after some time and gives me a blue screen.

  What can I do else? I appreciate your help. Thank you.

  If you want to have the factory settings once again, you must install recovery image using the recovery disk.
  Have you created this disk?

• Equium A200-1VO isue - white screen start new

  I got a new laptop Equium A200-1VO Friday as a Christmas present very very end and last night (Monday), I played football coach, play with ITunes and deleting files on an old mp3 player. Everything was fine when all of a sudden there was this click / the sound muffled and the screen went black.

  The laptop is connected to the time and so connected them to clear a/c was, so was the power and charge light, but he just stayed empty.

  I then unplugged the charger and it appeared with the orange light mean low battery. I then removed the computer game disc thinking that it is possible that and turned off the phone manually. Now if I just push the power button it stands theres a click, just about where is the hard drive and it stops, if I hold it in theres a click, but it stays on, all the time the screen remains blank.

  I then turned off and it rebooted I was wondering if it was just low on battery and still nothing.
  I left the place cell phone off during the night but in the morning, the problems are still there. I even blocked the "product recovery" disk, but still no sign of life.

  I'll try to plug this moniter screen and see if this is the problem then he hopes to be able to tell you soon. Oh, one thing I can think is that I used it on my bed, is there a way it could have overheated? If Yes, then would not be leaving off all night helped / solved this problem?

  Thanks in advance!

  Have you tried to remove the battery and disconnect the AC for a while?
  I would recommend doing this!

  Remove the battery and the power adapter for about 20-30 min. After this short period of time to connect all the parts again and try to start Notepad.

  Maybe it helps

• G60-458DX CQ50z-100 CQ50-139WM: good day! A series of interchangeable CQ50 screen / Compatible with a G60 series?

  Good day! I hope that ALL have a nice time.

  HP Pavilion G60-458DX

  Compaq Presario CQ50z-100

  Compaq CQ50-139WM

  I have a G60-458DX with a bad screen. I think it's the backlight because it grayed out in front of me, but I can still see what is happening in the shadows.

  I have a CG50-139WM shipwreck which has a good screen I would use the G60.

  I also have a CQ50z-100 with a good screen that I as a substitute.

  Are these compatible screens / interchangeable?

  Your help with this project will be greatly appreciated and save me a lot of time.

  Kindness rocks!

  John V. Brennan

  Owego, NY

  Hello

  The following link shows all the parts for your G60-458DX:

  http://PartSurfer.HP.com/search.aspx?SearchText=VH171UA

  For the screen, none of them can be used with other two CQ50 machines

  488385 001
  http://PartSurfer.HP.com/search.aspx?SearchText=488385-001
  
  496764 001
  http://PartSurfer.HP.com/search.aspx?SearchText=496764-001
  
  496770 001
  http://PartSurfer.HP.com/search.aspx?SearchText=496770-001

  This is why 2 machines CQ50 screens do not work on the CQ60.

  Kind regards.