Why can't the PCI 6040E under devices and Interfaces
Hello!
I intend to use a PCI 6040 E connected to a BNC 2010 to measure 3 different voltages as an entry. I installed the mx of NOR-DAQ 9.7.5 on windows 7 (64-bit). My question is why I can't see my devices under the "devices and Interfaces? even by Labview, DAQ assistant, acquire the signal, anaolge of entry... I can't configure the devices of this error: no supported devices found.
Any idea? Thank you
You're going the wrong way. The latest version of DAQmx that supports PCI-6040 is 9.5.1. See this article for more information: OR-DAQmx and NOR-DAQ Driver Support: PCI/PXI devices. And LabVIEW 2011 is the latest version of LabVIEW that supports DAQmx 9.5.1.
Tags: NI Hardware
Similar Questions
-
Hi - Have cRIO
Can someone help me get the NI 9871 (Scan Interface) work? My two 9477 and two 9425 and 9403, function with the scanning Interface. In MAX > software > NOR-Serial RT 3.82 > NOR-Serial 9870 and Scan Engine Suport 3.8.2 9871 BUT NOT == MAX > devices and Interfaces > series & parallel = number of Ports Com for 9871 listed? Project, 4-port RS-485 NI 9871 is in slot1? Any help appreciated thanks
the serial ports on the NI 9871 also appear in MAX with serial ports integrated target under devices and Interfaces
NEITHER 9871 (Scan Interface)
I left the Slot 1 Slot 8 9871 Know works and MAX displays 4 COM ports. Something is misconfigured in Slot1?
Solved!
Thank you
-
Satellite L500 where I can download the PCI drivers audio No. 82801IB/IR/IH
Help, please. I have not installed the sound drivers / audio of my Toshiba Satellite L500, can someone please tell me where I can download the PCI drivers audio No. 82801IB/IR/IH
Its a chip intel.
Thank you.Hello
If you need drivers then I recommend the European driver of Toshiba page.
If you have a series of Australian for Toshiba laptop, then you should check the driver Toshiba Australia page.But if you need more specific information here, then you should put more details on the specifications and BONES as posted by Akuma.
-
Why can't the person I'm talking about does not hear me.
Why can't the person I'm talking can't hear me
Your question implies Skype? If so, the following support Skype can help: http://support.skype.com/en-us/faq/FA897/Why-can-t-the-other-person-hear-me
If the question is about Skype and it does not help, the Skype forum is: http://community.skype.com/t5/English/ct-p/English?profile.language=en
If you are not asking questions on Skype, please respond with more details. -
I have been using this Toshiba 750 GB USB 2.0 Portable Hard Drive to clone my computer with NTI echo regularly, but now I want to use the player to launch mirror Carbonite image on. Because the player was not visible under 'Computer' on my machine, I tried the portable player to the computer for Windows 7 to my wife where it displays correctly and I was able to do a full format of the portable drive. Despite this, my computer is not displayed under 'Computer' portable player, but it appears under "devices and printers"... Thank you for your understanding!
Thank you for your helpful answer. I tried all through and including uninstall NTI Echo without any resolution.
During the process, I found myself 'Computer management' which includes 'Disk management' where I saw the external hard drive in 'offline' status due to a conflict of signature. I clicked to the external drive to go "online" and now, it seems to work fine and is visible to E:
Thank you, once again!
-
In Dreamweaver CM³ why can't the workspace options? Where can I find 'AP draw div?
In Dreamweaver CM³ why can't the workspace options? Where can I find 'AP draw div' or one of my tools of "designer"?
Apart from APDivs, I don't know what are the other tools you talk, but DW has been modernized in the last version of delete a large number of redundant and old tools and shaped controls. APDivs are such a tool which has been deleted (and should be removed versions there are many, many).
With respect to the workspaces, you just create your own. Configure them as you want and you can have as much as you want.
-
MAX does not list the devices and Interfaces in the tree
When I open MAX, the tree displays only software in my system. I'm trying to access the devices and Interfaces, that should be included in the tree as well as a number of other elements. I've attached a screenshot of what I see. Why everything is not listed, and how can I solve this problem?
Spuleio,
You won't see if device drivers are not installed. Notice the button in the example that says "Open VISA Test Panel"? VISA is loaded with device drivers OR. You can find the drivers here. If you want just the VISA, I think you might be able to find it here. But, in both cases, NEITHER needs a way to talk to the port, hence the need for the driver.
Cheers, Matt
-
Computer listed under devices and printers in Windows 7
Hi all
I was wondering, is your computer itself supposed to be listed under devices in the peripheral zone and printer to Windows 7? Or is it a driver problem.
Thank you
ryguy2008
It's normal.
In addition, only connected external devices or devices that can be removed will appear in devices and printers.
-
I can access the internet, get on facebook and hotmail, but I can't pllay games on facebook and I can't open or respond to my e - but, anyone know wats up?
Hi Danny
It is a problem on Facebook. Here are links where you can get help.
Facebook Help Center | Facebook: http://www.facebook.com/help/
Facebook Support Forums: http://www.thefacebookforum.net/forum
Concerning
-
Why 'Device and Interface' lack of tree MAX Config?
I am trying to integrate a range of LeCroy WS64MXs with LabView, but no luck so far. In the measurement and Automation Explorer program, there is no worksheet named "Devices and Interfaces" in the configuration tree. All I have is 'My system-> software' and 'remote systems. Max version 4.5.0f0. This sheet should be there by default and if not, how it added to the tree?
-
Original title: outlook can duplicate the same messages from yesterday, and I can't delete them.
I use outlook express for my e-mail yesterday same emails keep coming, I tried to remove them, but can't everytime I open outlook I get the same
The other post:I opened outlook express the same messages from yesterday, continue to repeat every time error 0x800CCC0F had no new messages and I can't delete these messagesHi glendamcmillan,
You did it all change hardware or software on your computer before this problem?
You can follow this link & check if the problem persists:
Hope the helps of information.
-
through my scanner/printer and my educated place window tells me that program file could not be installed or to load and go to the Help menu under 'detect and repair '? I need help with this
Hello
you say not what e-mail program, you use!
It takes a lot more information
______________________________________________
see if this applies:
Looks like you need configure Windows Mail
you need to configure your e-mail account windows mail with your ISP internet service provider
They provide you with account settings you need to do
Ask them to
username
password for your access broadband account / distance with themServer of incoming POP3 mail
outgoing mail SMTP serverand here's how to configure windows mail after getting the email correct account settings
-
A creative cloud membership can be used on a Windows device and a Mac?
I'm working on a Windows and Mac device. A creative cloud membership can be used on a Windows device and a Mac?
Yes. You are allowed to install up to two platforms and they can be a Mac and a PC.
-
right click on "Devices and Interfaces" does nothing
Hey all,.
I am trying to add a raw TCP VISA OR max socket. When I right click on "Devices and Interfaces", the line is highlighted and any drop-down list appears, much like a left click. However, when I right click on 'Software', the drop-down list appears. I have all the software AND up-to-date. Is there additional software, that I should add (I NI-VISA 5.4 as well as the watering duration) visa?
Thank you
Matt
I think I know what is happening. It seems that you have just the duration of OR-installed VISA, but not the NI-VISA full supports, which includes additional support of MAX configuration.
With the new version of MAX 5.5, devices will appear with the help of configuration limited when you have only the version of the installed driver running as opposed to in the past when nothing arise.
Here is a link to the full installer 5.4 NI-VISA - http://joule.ni.com/nidu/cds/view/p/id/4230/lang/en
-
No devices and Interface in MAX
Hi all
I recently installed the evaluation version of LabVIEW and I try to communicate with a dynamometer of Mark-10 series 5. The problem, however, is that MAX doesn't detect the device or any other instrument. It's not even a tree device and Interface.
I am running Windows 7 and Mark-10 drivers are installed (and is detected by the device as a USB Device Manager).
Someone has an idea of what could be the problem?
And how are you trying to communicate with the hardware, GPIB, serial, usb, TCP/IP,...? Did you install NI-VISA is there and equipment driver provided by the manufacturer?
Note: MAX shows not only with products OR.
Ben64
Maybe you are looking for
-
BofA charge only mode WINDOWS safe - once in normal mode after that
FF 36.0.4 B of A does not - just clocks. WINDOWS (7) starting in safe mode, it works just fine all right. In fact, return to normal WINDOWS, it will work 1 time. After nada as it just of clocks. Eventually it will show the error code: ssl_error_inapp
-
I clicked on the application, but it does not work. He does not even recognize that I clicked it.
-
Acer Aspire R7-572-6423. no sound with HDMI
Hello I am running Windows 8.1 64-bit on the R7. I got the laptop connected to a receiver and the receiver connected to a TV. I am able to see my desktop on the TV but I have not any sound through the receiver. When I look at the reading devices D
-
original title: Hi, I have wireless internet in my house and I gave my password system so that others in my home with laptops can use my internet provider. I want to change my password now. How can I do this or do I need to contact my provider to do
-
Is it possible to query the values of an enforcement strategy?
Is there an API to query the values of an enforcement strategy?