Why I can't command show running on cisco switch

On a single switch, I found that some commands because they show execution or copy running-config tftp: on cisco switch WS-C2960X-24TS-L does not work it see more below. How I can use the command then show generally. Thank you.

Building1_FAA_6F_SW3 #sh run
Building configuration...

Current configuration: 100 bytes
!
! No change since the last restart configuration
!
boot-start-marker
boot-end-marker
!
!
!
!
!
!
end

---------------------------------------------------

Building1_FAA_6F_SW3 #copy running-config tftp:
^
Invalid entry % detected at ' ^' marker.

OK, so the information you provided in your latest messages confirm that the privilege level you get via telnet/vty is different from the one you get via the console. This is due to the configuration of AAA which applies to the vty ports but not on the console port.

So if you want the same rules apply to the console port, then you must configure the port console for AAA as well.

If you don't want these rules then you need to remove the AAA configurations. The best way to remove these is by typing 'no new aaa - model' However, careful not to lock you out of the unit. Make sure you have local accounts with the privilege level 15 and you also know the active password/secret.

I hope this helps!

Thank you for evaluating useful messages!

Tags: Cisco Security

Similar Questions

  • Can you keep programs running even if switch you users?

    I work for a College radio station, and we strive to simplify our broadcasting system. We are building a new computer and want to get rid of the 2 computer we use now.  We used Adobe Media encoder to broadcast our stream. We want that, running on a single account and let the DJs use a different account, so they don't mess with the settings or play with the encoder without authorization. is this possible?

    Switch users without logging

    If you have multiple user accounts on your computer, the fast user switching is an easy way for another person to connect to the computer without logging or close your programs and files. For instructions on creating user accounts, see create a user account.

    1. Click the Start button and then click the arrow next to the button stop.
    2. Click on change user.

    3. Press Ctrl + Alt + Delete and then click the user you want to switch to.

    Note

    If you are connected to a remote computer (for example, using Remote Desktop connection), you cannot use the quick change of user on this computer.

    Warning

    Be sure to save all open files before switching users because Windows does not automatically save files that are open. If you switch to another user account and the user shuts down the computer, any unsaved changes to the files that are open on your account will be lost.

    http://Windows.Microsoft.com/en-us/Windows7/switch-users-without-logging-off

  • Why can't I just run netsh wlan show drivers on my windows desktop 8?

    Original title: on wify

    Why can't I just run netsh wlan show drivers on my windows desktop 8?

    Hello

    Please answer a few questions to refine the question.

    1 are logged as administrator? What exactly is the problem you are having?

    2. what happens when you enter the command?

    3. do you receive any error messages?

    Make sure that autoconfiguration WLAN service is started in the Services. Otherwise, you can start the service and check the results.

    Autoconfiguration WLAN service is a service which configures wireless connectivity and security settings.

    a. press the Windows key + R and type "services.msc" and press ENTER.

    b. in the details pane, under name, access the autoconfiguration WLAN Service.

    c. right-click the autoconfiguration WLAN Serviceand click Propertiesand then click the general tab, do the following:

    d. in Startup type, select Automatic.

    e. the Service status, click Start.

    f. click OK and check the status.

    Hope this information helps. Provide more information so that we can help you.

  • I have an Imac - route Safari super, super slow.  Google Chrome fast? - why Safari can't run fast

    I have an Imac - route Safari super, super slow.  Google Chrome fast? - why Safari can't run fast

    Try to reset the settings of Safari:

    1. open Safari

    2. click on the Safari menu at the top (to the right of the Apple logo)

    3. Select the Preferences/Privacy tab

    4. click on remove all data from the Web site

    5. close Safari.

    Remove cache Safari files:

    1. click on finder

    2. look for the menu GO to top

    3. click on GO and hold down the option key. This will show a user library folder.

    4. click library and find the Caches folder

    5. in the folder caches com.apple.Safari Ouvrezledossier

    6. move the Cache.db file Trash.

    This should solve the problem. If it does not help, try to disable the Safari extensions

    1. open Safari

    2. click on the Safari menu at the top (to the right of the Apple logo)

    3. Select Preferences

    4. find the Extensions tab

    5 disable all extensions of

    6. relaunch Safari

  • can someone tell me why I can't update to El Capitan 10.11.2? the line "Show details" gets up and I click on it to make the update. When I do this, it just goes back to doing nothing, so I can never get past this point.

    can someone tell me why I can't update to El Capitan 10.11.2?

    When I try to update "updates available have changed" guest shows up.i click "Show details" prompt to complete the update and when I do that, it just goes back to doing nothing, so I can never get past this point. can someone help me with this, please?

    Thank you very much.

    In some cases, this error message is caused by a problem in the network. Restart your router as your device at wide band, if they are separated. If there is no change, see below.

    This procedure will remove some temporary and cache files. The files are generated automatically and do not contain any of your data. Sometimes they can become corrupted and cause problems like yours.

    Please, back up all data and read this message before doing anything.

    Triple-click anywhere in the line below on this page to select this option:

    /var/folders/zz/zyxvpxvq6csfxvn_n00000s0000068

    Right-click or Ctrl-click on the highlighted line and select

    Services ▹ reveal in Finder (or just to reveal)

    the contextual menu.* file should open with a selected subfolder. The subfolder has a long name beginning with "zyx" and ending with "68". Place this subfolder in the trash. Do not move other subfolders with similar names. You may be prompted for administrator login password. Restart the computer and empty the trash.

    * If you do not see the item context menu copy the selected text in the Clipboard by pressing Control-C key combination. In the Finder, select

    Go ▹ go to the folder...

    from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  • Why you can not run portable applications on RT?

    Why you can not run portable applications on RT?

    Nothing is installed on the system. That's all, flash USB, a folder or drive.
    You don't have to install anything. So why can not run portable applications on RT?

    I know exactly what is a portable application. It requires no additional drivers installed or libraries to run on a system, if one is required that they are either built into the executable and extracted the runtime or are included in the same location as the executable and are referenced from this location.

    No portable application is not somehow the operating system to display the current status, error messages or generate logs for its operation. If it cannot accept input during its operation or generate a form of output it has no function. This is the basic description of a program to have one or the other or both.

    When you double-click an executable file is Windows (if it's the operating system) giving you the ability to open its location, see the executable file in order to select and issue the command to run. It's Windows that then loads this program in memory to run. If necessary, Windows that displays the dialog box to provide any input and display results or error messages generated by the program. If the result is a log file that it is Windows that allows access to the drive to create the file and the result is an error state in Windows that stores the status of the error, then it can be interpreted by another program. If the output is to change the status of the computer in a way, it's Windows that gives access to this device or component. The Hardware Abstraction Layer allows access to the hardware itself if necessary by a program and even that is a part of Windows.

    So I know what a laptop program is, more important still, I also know what is Windows.

  • Why I can't run iPhoto after update to Yosemite 10.10.5?

    Why I can't run iPhoto after update to Yosemite 10.10.5?

    With no details we cannot guess... have not updated to iPhoto? What version do you have?

  • Why my macbook air back show my Facebook messages when I am not connected? What can I do to stop?

    Why my macbook air back show my Facebook messages when I am not connected? What can I do to stop?

    Hello, welcome to the discussion!

    If you are referring to push notifications on your desktop, you most likely have Facebook as an internet account on your MacBook. You can withdraw from your account, or disable notifications for it.

    Open system preferences > Internet accounts

    Select Facebook

    Uncheck the Notifications tab to disable the notifications or click on the "-" button to remove the account

  • How can I set the time axis on my waveform table to show run time that is to say whenever I start the program I should have 0 as the starting point

    How can I set the time axis on my waveform table to show run time that is to say whenever I start the program I should have 0 as the starting point. I've been messing around with the without success. I'm under Labview 2012.

    Thank you!

    Townes wrote:

    I can't understand what you mean. I have no formal training with labview. It took me a long time to write the simple program that I joined. Any guidance would be greatly appreciated!

    Its pretty normal for a beginner to take the time to write code. Right-click the map of waveform > Create > property node > historical data, you will get a property node, keep this at the beginning of the code and create a constant. You can also go to the VI properties and > run and select "clear indicators when it is called.

    I recommend you to go through the basic materials of LabVIEW which will give you an understanding on the basics of bases/components of LabVIEW.

  • Why I can't update my credit card payment information? It shows the error in the server. How can I make contact with the staff of Adobe?

    Why I can't update my credit card payment information? It shows the error in the server. How can I make contact with the staff of Adobe?Screen Shot 2016-08-29 at 9.18.44 PM.png

    Hi Purple % 20Lambs,

    Please contact Adobe support:Contact customer service

    * Be sure to stay connected with your Adobe ID before accessing the link above *.

    In case you can't reach Adobe support, please see:

    Contact the technical support FAQ: Impossible to reach support via the link "contact us".

  • Please let me know why I can not download Flashplayer because it runs the scripts on the page... I bought acrobat dc 7/10.  Thank you.

    Please let me know why I can not download Flashplayer because it runs the scripts on the page... I bought acrobat dc 7/10.  Thank you very much. @@

    Hi dmrmultimedias,

    I guess you are referring to the script error using the installer online.  If so, the DPI setting has been identified as the culprit.  If the DPI setting is not set to 100%, 125%, 150% or 200% installer will return the script error.  If your DPI setting is set to something else, please set it to one of these and Setup online should work.  The team is working on a fix for this.

    To check/change the DPI setting:

    1. start the control panel and go to control Panel\All Control Panel Items\Display

    2. in the left menu, select the custom text size (DPI)

    3. in the custom configuration Windows DPI select 100%, 125%, 150% or 200% in the menu drop-down

    4. Select OK

    5. Select apply

    6. open a session/disable

    7. online installer should now run without displaying the script error.

    This is planned which will be fixed within two 2 weeks.

    --

    Maria

  • When I m showing police area I do not see the type fonts? Why? or why I can do to fix this?

    When I m showing police area I do not see the type fonts? Why? or why I can do to fix this?

    Mijail,

    I think that it can fix:

    Open system preferences and go to accessibility. Then select display in the source on the left side list, then check the box transparency reduced.

    It was introduced in this #15 post by TheUlser:

    https://forums.Adobe.com/message/6854594#6854594

    It has been described on this page from Adobe:

    http://capitalmacservice.com/font-preview-working-Illustrator-CS-5-Yosemite-fix/

    It may also depend on the monitor, as shown in the message #29 by Loncar in the same thread.

    Of course, this also affects other things so there can be a downside to it, of course, the influences of transparency reduced the appearance of other things, but so far nobody complained disadvantages.

  • Why the following command cannot run correctly?

    Why the following command cannot run correctly?
    SQL> exec DBMS_SPM.EVOLVE_SQL_PLAN_BASELINE;
    BEGIN DBMS_SPM.EVOLVE_SQL_PLAN_BASELINE; END;
    
          *
    ERROR at line 1:
    ORA-06550: line 1, column 7:
    PLS-00306: wrong number or types of arguments in call to
    'EVOLVE_SQL_PLAN_BASELINE'
    ORA-06550: line 1, column 7:
    PL/SQL: Statement ignored

    Because it is a FUNCTION and not a PROCEDURE.

    http://download.Oracle.com/docs/CD/B28359_01/AppDev.111/b28419/d_spm.htm#CACEBBEI

  • I can't install CS4 on my new mac computer. It shows error 150:30. If I bought my photoshop CS4, why I can not install it?

    why I can not install my paid for photoshop CS4 on my new mac computer... it displays error 150:30?

    See this:

    Error "Licensing has stopped working". Mac OS

  • Why I can't grant execute on a directory?

    Why I can't grant run in a directory?

    I realized the following:

    Connect as SYS

    Prove that the oracle directory exists SELECT * from all_directories WHERE the directory_name = "nom_repertoire";

    GRANT EXECUTE ON nom_repertoire TO role-name DIRECTORY.

    The following documentation to the following address says I can grant to run:

    http://www.morganslibrary.org/reference/directories.html

    And yet when I realized the administrator to do and when I query the database to see if he did, it shows me that he has done:
    GRANTOR                        GRANTEE                        TABLE_SCHEMA                   TABLE_NAME                     PRIVILEGE                                GRANTABLE HIERARCHY 
    ------------------------------ ------------------------------ ------------------------------ ------------------------------ ---------------------------------------- --------- --------- 
    SYSTEM                         role_name                    SYS                            dir_name                     EXECUTE                                  NO        NO        
    SYSTEM                         role_name                    SYS                            dir_name                     READ                                     NO        NO        
    SYSTEM                         role_name                    SYS                            dir_name                     WRITE                                    NO        NO        
    
    3 rows selected
    When I try in my environment of xe, it throws the error:
    Error starting at line 1 in command:
    GRANT EXECUTE ON DIRECTORY dir_name TO role_name
    Error report:
    SQL Error: ORA-22928: invalid privilege on directories
    22928. 00000 -  "invalid privilege on directories"
    *Cause:    An attempt was made to grant or revoke an invalid privilege on a
               directory.
    *Action:   Only CREATE, DELETE, READ and WRITE privileges can be granted or
               revoked on directories. Do not grant or revoke other privileges.
    What is going on?

    Benton

    Benton says:
    Why I can't grant run in a directory?

    Because you cannot, according to the 10 g documentation...

    http://download.Oracle.com/docs/CD/B19306_01/server.102/b14200/statements_9013.htm#BGEJEBCJ

    However, in 11g, it can be done...

    http://download.Oracle.com/docs/CD/E11882_01/server.112/e17118/statements_9013.htm#BGBCIIEG

Maybe you are looking for

  • can not set up an e-mail account

    I use Thunderbird 31.7.0 in a Fedora 20 distribution. I installed Thunderbird using yum provided distribution. Then I tried to configure my [email protected] existing accounts and my [email protected] using IMAP and pop Thunderbird was

  • When to call DSDisposeHandle when you have a DLL function acting as a dynamic data DS source extensible?

    Hello I have a dynamic function DLL acting as a data source within a LabVIEW application (see attachment) - I use DSNewHandle to dynamically allocate an array 2D handle storage via the Manager memory LV for arrays of arbitrary in application size dat

  • can someone convert my WMM project to a wmv file?

    Hello have beeen fighting with movie maker to convert a project file to a wmv. have followed all the steps of "save computer" but instead to save only "minutes remaining" constantly climbing (in thousands) no save. used wmv files to create project bu

  • Updates will not take

    I am running Windows XP SP3 and there are three updates that it does not accept. They are KB2656407, KB2657424 and KB2604110, if that makes a difference. These three have just been back for a while now and I'm tired of seeing them. Can you help me in

  • Plant of the UCS 1.2 (1f) TFTP question backup

    I noticed that a TFTP backup (full-State) of the UCS Center on version 1.2 (1f) does not work as a restoration, however if you run a local backup in the center of the UCS and download the file, you can use this one to restore via TFTP Obviously it's