Why is the battery loses power even when connected to the wall of entry?

Similar Questions

• Satellite P855 - 10G is low on battery power, even when it is off

  Hello world

  I bought the Toshiba Satellite P855 - 10G, but I m terrified because he is low on battery power, even when it is off...
  Anyone know how I can fix the problem?

  Best regards
  Igor Tarelho

  Hello

  Access the BIOS and disable options like: wake-up on LAN and keyboard.
  In Toshiba HW Setup I should disable the USB Sleep and Charge feature as well

  The two options enabled to discharge the battery, even if the device is OFF

• The battery charge falls even when it is plugged into the satellite series

  I have a laptop satellite and although it recognizes the power adapter when it is connected and that the icon in the taskbar shows "load", the percentage of the battery charge seems down.

  It is only while the laptop is turned on, because it does not charge the battery when it is turned off.
  I didn't know that he used the power of the battery so that hip, so I'm puzzled by this not only why the battery doesn't seem to be in charge, but also why the battery seems to fall once the laptop doesn't have to use it anyway.

  Any help is appreciated!

  Hello

  I saw this problem on my own laptop in the past. even if the laptop is charging, the battery seems to fall in charge.

  This indicates that the battery life is coming to an end, there are a limited number of cycles of load for a battery before it dies.
  Also when you have the computer is off fresh is always lost at a considerable pace, because the battery is good, "die."

  You can't do anything on this issue except to buy a new replacement battery for your laptop computer to a repair center authorized Toshiba. This should answer your question.

• Pavilion dv7: HP Pavilion dv7 has no power even when plugged

  My laptop battery ran out today and would not take a load... I checked all the cord etc. and it is the power of the laptop, but now the battery is completely dead and the computer is also dead even when it is plugged into an AC.  I've deleted and reinstalled battery... no help.

  Is this a battery problem?  If it was, then, why the computer would not work when plugged in the AC?

  Any help would be appreciated...

  The first thing to try is a hard reset as follows:

  (1) remove the battery and unplug the DC power adapter.
  (2) press and hold the power button for more than 15 seconds.
  (3) plug the DC power adapter (leave the battery for now)
  4) press the power button

  If that produces no positive results, then continue with the following troubleshooting instructions.

  Is there a light power light on the laptop when the piower adapter is connected and connected to a domestic supply?

  If this isn't the case, then the laptop adapter may have failed and is unable to charge the battery or power the laptop on its own.

  Acts of power as a diagnostic power adapter LED and not lit is an indocation external power is not OK.

• I can't see the list of available wireless even when connected to wireless internet connections.

  I can't see the list of available wireless connections. So I can't connect to new wireless connections as I have not logged in before. The icon in the taskbar that would show you the possible connections disappeared. Nothing shows under connections network under Favorites network even when I'm logged in. I can pick up internet connections from earlier I can't see that one that is connected to or control it. Help, please. Thank you.

  Hi CorneliusE,

  1. what service pack is installed on the computer?

  2. what exactly happens when you try to view wireless networks? You receive error message nay?

  3. do you have security software installed on the computer?

  4 did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: You can follow the steps in the article and check if that helps you find the wireless network.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702

  Note: Article applies to Windows XP SP 2, however, can also be tried with other versions of Windows XP as well.

  Method 2: If the method above is not enough, you can consult the following articles and check.

  How to configure TCP/IP to use DNS in Windows XP

  http://support.Microsoft.com/kb/305553

   

  To test TCP/IP connections by using the ping and the commands net view

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/sag_tcpip_pro_pingconnect.mspx?mfr=true

   

  Let us know if that helps.

• Why my computer is running slowly even when I do not have a virus?

  I find the virus and there is none. but my computer is very slow

  Hello

  What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
  on this machine, including those you have uninstalled (they leave leftovers behind which can cause
  strange problems).

  ----------------------------------------------------

  Follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows Vista
  http://support.Microsoft.com/kb/929135
  How to troubleshoot performance issues in Windows Vista
  http://support.Microsoft.com/kb/950685

  Optimize the performance of Microsoft Windows Vista
  http://support.Microsoft.com/kb/959062
  To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
  Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
  reference (if you have a small box at the bottom left - show for all users, then check that).

  How to check and change Vista startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  A quick check to see that load method 2 is - using MSCONFIG then put a list of
  those here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out which files, key of registry and other objects processes have opened.
  What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
  each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically when you start your system
  and you log in. Autoruns also shows you the full list of registry and file locations where applications can
  Configure auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  -Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
  When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
  Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
  a program that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe not. The window
  Watcher says it all, reporting of any window created by running programs, if the window
  is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp

  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
  get new manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ===========================================

  Refer to these discussions because many more excellent advice however don't forget to check your antivirus
  programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
  first.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  Hope these helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Why battery loses power when Satellite-A-50 is stopped?

  After a few days the battery of my Satellite-A-50 (two months ago) going from 100% to 4%, while the laptop is turned off.

  I tried with the start - stop function (windows 8.1) and tried to close by maintaining that the button for 5 seconds and the laptop is closed.

  But in a few days, the battery is low.

  How is that possible? What can I do?

  Thank you
  Adrianus

  This has been discussed several times here in the forum.
  I recommend you to use the search function of the forum and read some other discussions.

  But let me tell you that win 8.1 does not power the cell phone completely off by default. It defines the laptop only hybrid close mode for faster start.

  To turn off this doc check function:
  http://APS2.toshiba-tro.de/KB0/TSB2B03EY0002R01.htm

  Also the BIOS contains options that allow the laptop to power all its completely OFF. For example: Wake up LAN or Wake up on keyboard mode.
  These options wasting energy from the battery even if the device has been turned off.
  That is why it s advisable to turn it off.

• Why does my internet work randomly even when the screen saver is turned off?

  When I connect and start the computer to the top and all, computer speakers begin to work as if I was already on the Internet. When the screen saver went off the screen and the screen is black, you can hear the speakers go to random times, as if I was online but I'm not. Need help please, my computer looks like its haunted by video ads. This was initially the Visa Commercial card, secondly the advertising of McDonald's.

  My updates are not updated, I also tried for two weeks, I need help here too. I have now accumulated 17 updates to download, but they do not.

  WIndows XP

  Use the link below to search for viruses you machine.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

• Why cfstat still poster reqs qued even when it is not all traffic to the site?

  I try to use cfstat to help understand some performance issues with our production server. Its CF 10 Ent on a Windows 2008 VM. I'm also 10 ColdFusion installed on a local Windows VM.

  I run cfstat with a 1 Refresh second on the local production and the VM server. The local VM Reqs Q column ' ed shows a constant 10 even if I'm not hitting all sites on the server. The production server shows a constant 20-Reqs Q'ed and some Run Reqs'g.

  Is this normal? I have to make some adjustments to the CF or the JVM?

  Thank you

  Hi Phil,

  CF10 CFSTAT seems not to be as convenient as CF9 or earlier version.

  Requests queued seems to be displaying the value of tomcat for minSpareThreads connector. Tomcat minSpareThreads is the minimum number of threads still kept running. If not specified, the default value of 10 is used.

  HTH, Carl.

• Satellite P200-1IE: battery goes down even if connected power outlet

  Hope someone can give me some good advice here as an urgent decision to make about my P200-2 - week old 1IE, under Vista Home Premium, I bought the Portugal where I live. I was told that I have 15 days to return the machine to the store if I am not satisfied, then I must act quickly.

  Background info: I have not yet downloaded SP1 updates or drivers or bios on the Toshiba site. That once the machine has been run on battery (accidentally when the power was off) - he ran down, beep and a time that I realized and turned on the power, is it charged normally. The machine works very well, and then last night a strange problem occurred.

  The machine was left unattended and ends by closes. When it has been restarted the battery alert was a sound signal. My husband na? A´t realize that it was, and close again the machine. When I got to watch it I noticed that even though the power light was there was no light to the battery, or orange or blue, nothing.

  I turned on and checked the battery which was about 20%, but that the power supply has been connected to the taskbar icon energy showed that the battery was not charging in fact it unloaded quickly at a minimum. I stop the machine, then the battery light orange came for about 5 minutes, then went out again. Play with this problem, try to troubleshoot gave strange and unpredictable results i.e.

  -unplugged and re plugged the power supply at the end of the machine and then no lights came, not even the power sector led.
  -is turned off and turned back on the power at the end of the plug and the sector and battery (orange) lights came on.
  -battery charge indicator is out after 10 minutes.
  -unplugged and reconnected the power to the machine again and this time the sector and battery lights came on - even once, they came out after about 10 minutes.
  -power the computer on. The power icon showed about 25% power. Not powered down the new machine - no lights at all.
  -entretienavec and re-connected turns on power to the machine again and this time and battery charging sector came and stayed on.
  -After about 2 hours, the battery light showed charged (turns blue) and so I unplugged the power socket and left for this morning.

  As I suspected, this morning the battery power was 100%. Everything seems normal (except the battery light is released briefly on starting the machine, which is maybe normal and I just never paid attention to the front). I unplugged the power supply and let it run on the battery for about 10 minutes (this is plan is Equilibrado which I believe is balanced). I then reconnected power and loaded back up to 100% as you can imagine.

  Sorry for the long description, but even if all is well, now strange problems yesterday let me feel that there is a potentially serious problem within the machine. Has anyone encountered anything like this before and what do you think I should please?

  Hello

  It s a long and very strange history.

  My first idea was a battery issue but to be honest it is really not easy to say why this problem occurred, it would also be possible that this would cause to loses connection

  I think you should visit you laptop dealer and eventually you could substitute other P200.

• Re: Satellite U400 - battery loses power while he is in charge

  Hello

  I did not do anything with my laptop, just to turn it off and then after a few hours later I turned it on, and then he said: battery charge, but instead to go from 90 to 91, 92 down from 99 to 90, then 80 and he cut it while the battery recharges ;(

  That please?

  Once I finally sucssed the full battery but then when I shut down the pc, NOT SHUT DOWN just that close to start the hibernation, then he the of to is the same thing that happened once again I have to charge the battery and then it comes down to % instead of upwards, why ;(?

  thnx.

  What version of BIOS that you use?
  As much as I know the BIOS must be updated to version 3.0 or higher.

• The battery will be discharged when my Satellite L670 is turned off and unplugged

  I have the Satellite L670-1john 3 months.

  the battery will discharge when the PC is turned off and unplugged.

  How to solve the problem?

  > the battery will discharge when the PC is turned off and unplugged.
  How to understand this?
  Does it means 24 hours battery is completely discharged or what?

  Battery loses power when the laptop is turned OFF and unplugged and there is nothing unusual.
  Enter the BIOS settings and disable Wake up on LAN.

  After doing this watch carefully what will happen and let us know if the battery will discharge both than before.

• My battery does not charge even when it is plugged and my orange light blinks when it is plugged.

  My cord broke first, then I got the exact cord to fit my computer. Them I got 75% battery charge, but even when it is plugged in the light to connect it to the computer itself has never been white once again, it flashes orange. Now, I'm down to 2% and I tried to load it. It will not be loaded. I tried to take the battery out and just have it is plugged in, but still it flashes orange. Not white as before. What could be wrong?

  The battery? Batteries will you know. Tried to contact the Office of support for your laptop brand?

• My new Kindle Fire HD when connected to USB causes files on my external HARD drive to go away, they come back when the Kindle is disconnected and after a reboot, any help please

  If after installation with kindle, connected external HARD drive disappears

  USB ports are usually "matched" in groups, called hubs root.  These root hubs then control and distribute the power to the USB ports.  If any device on one of the two ports, the hub root, requires too much power, the other port loses power.  When a port USB Hub root loses power, the devices connected to the port 'disappears' of the Windows session.  Normally, after you disconnect the devices from the USB port and reconnect them "must" bring these.

  A free USB powered hub can help.  These allow usually additional power over USB ports, on its own USB ports.

• Modification of the Module dependency entries in the generated file to COD

  Hi all

  I am trying to build a blackberry application that uses web services. I use my own implementation of web service client because most of the mobile does not support RPC or JSR 172. So I do not use net_rim_jaxrpc blackberry module. I tried to deploy the application in 8130 (Verizon) Pearl and Curve 8320 (T-Mobile). It works very well in Pearl but he launched 'Net_rim_jaxrpc Module could not be found' error in curve 8320. I looked for versions of software to both phones. Pearl has a version 4.3 and curve has a version 4.2. I know that version 4.2 doesn't have a net_rim_jaxrpc module, then it throws the error message. I looked in the JAD file and it has an entry for net_rim_jaxrpc in "RIM-COD-Module-dependencies. My question is, since I do not use net_rim_jaxrpc API why he puts this entry in the JAD. I even tried to delete this entry from the JAD but curve 8320 always up the error message. If its configuration "RIM-COD-Module-dependencies" in another place in the COD file. If under its weight so why is - do this so that even when I'm not using the API. And how to remove this entry for dependence. I use eclipse 3.2 for development.

  Someone please help me on this.

  Thank you

  Gopi

  The problem is resolved. Problem is not with the development version. Problem is with the import statement. There was an import for 'javax.xml.rpc.Stub' statement, and I don't notice it. But when I changed the JDE 4.2 development, he began to show an error message for the unknown variable in the IDE. I changed the import to my own Stub class and everything seems to work very well.

  Thank you for everything that you guys!

  I have another question. I have a custom button and clicking on it opens the BB browser. On the development, I need the button to look like a hypertext link with the symbol of the hyperlink (a symbol of the hand). Can anyone suggest me something on this? I have to do something in the drawFocus or onFocus the custom button?

  Thank you

  Gopi