Why my audio midi Setup does not recognize my external midi devices?

Similar Questions

• Satellite L750 does not recognize an external microphone

  My laptop does not recognize any external audio input device plugged into the mic port.

  I have a Satellite L750 running Windows 7 with the Conexant HD Audio Smart.

  I want to record using external mixer. I am connect the output of the bureau in the 3.5 mm microphone port, but it seems that it is still just using the internal mic.

  When I go into the sound properties, under the recording tab, it is only the internal mic. There is no option for an external mic.

  I tried updating the driver for sound card, remove the card driver sound and re - install, check all the properties under sound properties, but there is no option for the external microphone.

  I tried Googling the problem but nobody seems to have a viable solution.

  Please can someone help me get the laptop to recognize an external mic.

  > I want to record using external mixer. I am connect the output of the bureau in the 3.5 mm microphone port, but it seems that it is still just using the internal microphone

  Start a test: take an external microphone, connect it to the laptop and use a Windows 7 Audio Recorder utility (can be found in all programs-> Accessories) to record an audio sample.

  Is this possible?

  I think that the microphone that appears in the control-> audio-> recording tab panel is the external microphone jack.
  You can also click right in the recording tab and must mark the options: show disconnected devices and devices to see the disabled.

  By the way: find an old thread you created here on the similar theme:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=69099
  I advise to use only a single thread to continue the discussions.

• Desk top HP does not recognize the external hard drive

  My HP Envy Phoenix 810 does not recognize my external hard drive Seagate 3 TB, which is installed in the drive enclosure hard Bytec HD-35SU3-BX. Have you tried two different 3 TB HD and two boxes of Bytec and nothing works.  When I installed my 1 TB in the same pregnant, it works.  Why my computer won't allow me to use my 3 TB HDDs?  I use Windows 7 and Internet Explorer 11.

  I suggest you directly contact Bytecc and inquire 3 TB HD the HD manufacturer is supported. I had an old AZIO dock who does not identify / initial with WD drives.  It was a firmware issue.

• Portege Z930-118 does not recognize the external USB CD/DVD drive

  My new Z930-118, with windows 7 64 bit home, does not recognize the external CD/DVD drive when I plug it into the USB port.

  The CD/DVD device does not even appear at all in Device Manager.

  The reader is a SE-S084 Samsun and works well on another laptop.

  I already checked for the "upper_filter", "lower_filter" with the regedit, but entries are not there, so no help.

  Hello
  I m not very well how to help you.

  I found some information about this WEIRD disc and it seems that he didn't need an external power supply. Its USB bus powered so I guess around 500mA power since it is the default value provided by a USB 2.0 port.

  I don t think that there is a problem of missing software. It is a plug n play device so you need to connect it to the USB port and the system should automatically recognise.

  From my point of view of the few you try to connect the external USB ODD two ports to aid a * Y * Cableusb.
  I think the reader needs more power provided by a single USB port.

• Lenovo B50-50 does not recognize my external hard drive

  I recently bought a laptop Lenovo B50-50 and it does not recognize my external hard drive. It's a WD elements with USB 3.0 storage device. I tried a few of the fixes recommended on other forums, but none of them work. The hard drive comes up is the list in Device Manager, and all my usb drivers are up to date. The hard drive works perfectly on other devices. Other work of readers of fine nib. Normally when the hard drive connected to the aa one device in flashing lights. This does not happen when I connect it to my laptop.

  Any help much appreciated.

  Make sure you use your laptop, 3 USB ports, not then a USB 2 port to see if one will work. If it does not power up to contact Western Digital for support.

  Good luck.

  CB

• Backup Win XP does not recognize my external hard drive

  Windows XP Backup Wizard does not recognize my external hard drive and does not list it as an option for storing backups.  I suspect a registry problem because the backup wizard previously recognized this drive and saved on it several times before I was running ARO 2012 for cleaning the registry errors.  I can always open the player in windows Explorer and see the files it contains, but Explorer Windows XP now lists the drive as an "expansion disc" instead of a 'removable disk '.  When I right click in windows Explorer and open 'properties' for this drive, it shows it as a 'local disk' instead of a 'removable disk '.  The drive is ok when I click the button 'Remove hardware safely', and it reports "safe to remove hardware" after I click on "USB storage device - Drive (J :). ».  Help!

  Who did.  Thank you!  Now... I used Aero2012 to clean up the errors in my registry that's because my computer is desperately slow, especially when you start (8-10 minutes) and also with internet explore (move cursor to previous typos when you compose a new e-mail message).  Is there a safe way for me to speed up my computer?

• Microsoft does not recognize my external dvd burner.

  Microsoft does not recognize my external dvd burner.

  External DVD drives tend to require a driver for it.  Check the support web site of the manufacturer of the drive for details on how to install the player.

• computer does not recognize my external hard drive, how to fix

  my computer does not recognize my external hard drive and need to know how to fix it. I need to access files on the hard drive. AS SOON AS POSSIBLE

  Hello

  I suggest you to follow these steps and check if that helps.

  Method 1:
  Step 1:

  Go to Device Manager and check if the hard drive is it recognized.

  Step 2:
  Go check and management disk if the hard drive is recognized, if so, then try changing the drive letter and check if it helps:
  http://Windows.Microsoft.com/en-us/Windows-Vista/change-add-or-remove-a-drive-letter

  Method 2:
  Try to run this under fixit and check if it helps:
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Also check out this link:
  http://support.Microsoft.com/kb/948911

  It will be useful.

• Windows 7 does not recognize my external screen.

  Windows 7 does not recognize my external screen.  I checked the driver and even of the went to the NVIDIA site and plugged my material for my graphics card ID to get the correct driver and yet, it does not recognize it!  So here's what I have right now since I've upgraded to Windows 7 Ultimate edition = Standard VGA graphics card.  If someone has a legitimate solution to this problem, feel free to comment! Thank you

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows Vista does not recognize my external hard drive, Eagle Consus AND-CS2PSU2-BK

  I have an HP Presario laptop running Windows Vista and it does not recognize my external hard drive, or my flash drives.

  I have an external hard drive Eagle Consus AND-CS2PSU2-BK.  It worked fine on my desktop, which works on XP.  I plug it to my computer laptop and nothing.

  When I plugged it in the first place, he says that he needed to download the drivers.  I clicked 'ok' to automatically download drivers and a few seconds later, he said that it successfully completed the driver download/install.

  I look under the drives in my computer and he's not here.

  I went to start, right click computer, left you click on Manage and double-clique then under storage disk management.  All I see are C drive and recovery disc (D).  No other drives displayed.

  I exitted who and set up the Control Panel, double click on Device Manager.  He said in the other topic peripheral USB to ATA/ATAPI bridge.  I don't know whether or not it is my external hard drive.  It indicates the Type of device: Other Devices and under device status it says: "the drivers for this device are not installed. (Code 28).  This operation requires an interactive window station.  To reinstall the drivers for this device, click on reinstall the driver. »

  He asks if I want to reinstall the drivers, so I clicked that.  He couldn't find them / install them.

  Still, I don't know if USB to ATA/ATAPI bridge is still linked to my external hard drive.

  Help, please.  The same thing happens when I try to plug a flash/USB.

  Try this:

  In the right click 'USB to ATA/ATAPI bridge' Device Manager under the other devices section, click unsintall or press the delete key. Reset with the connected hard drive it must be reinstalled, but under the USB controllers. Make sure the device works on the other computer cable can also go to bad.b

• W7 Device Manager does not recognize the Intel AMT devices

  Please help: where can I find - how to install the latest drivers Intel AMT for Windows 7.

  Hello

  Thank you for the question to Microsoft Community. I'll give my best to help you.

  From your problem description, I understand that the Device Manager does not recognize the Intel AMT devices

  What is the brand and model of the computer?

  Check out these links and see if they help.

  Computers that use Intel's vPro technology can have devices that are not recognized in Windows 7 Device Manager

  http://support.Microsoft.com/kb/976728

  Clean installation WARNING: Back up your files before you begin reinstalling Windows, even if you're reinstalling Windows on a hard disk partition. A clean installation replaces the current version of Windows and all personal files.

  If your motherboard supports AMT technology, you can download, install the drivers from this link.

  AMT: Intel® AMT Driver for Intel® motherboards

  http://Downloadcenter.Intel.com/Detail_Desc.aspx?&DwnldID=16936

  Note: This download is valid for the products listed below.

  Intel® card mother DB43LD

  Intel® card mother DQ43AP

  Intel® card mother DQ45CB

  Intel® card mother DQ45EK

  If the problem persists, I suggest you to contact Intel support. http://communities.Intel.com/Community/Tech

• Windows 7 64 bit does not recognize the external hard drive.

  Windows 7 64 bit does not recognize the external hard drive.  I have an old 250 GB Western Digital external hard drive.  Neither of my windows 7 machines recognize it.  It does not show in the device, Manager of the computer Manager or Explorer.  Any help would be appreciated.  THX Mike

  Hello

  Initially, check if the hard drive is compatible with Windows 7.
  Check out the link - http://www.microsoft.com/windows/compatibility/windows-7/en-us/default.aspx
  See the help article and check if it helps.
  
  My drive does not appear in Windows Explorer
  http://support.Microsoft.com/kb/330140
   
  Tips for solving problems with USB devices (this also applies to windows 7)
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
   
  It will be useful.

• Aspire V does not recognize the USB/phone device. Why not?

  Why does my laptop recognize my phone more?       He knows some device USB is plugged in, but it does not recognize.

  Download and install the USB Samsung drivers:

  http://www.MoDaCo.com/forums/topic/361286-26122015-latestsamsung-USB-drivers-for-mobile-phones-15550...

• Why Satellite L300-10 q does not recognize wireless network

  This new laptop works well on a wired LAN but does not recognize a wireless local area network. Received the message no network found. In the same room with another PC laptop Toshiba the wireless LAN is located and has good signal strength.
  The wireless LAN switch is on and the 'antenna' pictogram led burns red.

  Seems that it is not configured for detection. No idea how to solve this problem?

  Hello

  You´re sure you checked all THE settings? I mean, if the local wired network works and the wireless is enabled, you need to check all the parameters available that could be done. One idea would be to check the L300 on another access point to make sure that the problem persists on different brands of wireless routers.

  Please check this first and make sure that your settings are all on "automatic" so if you do not find the reason, come back and we will try to find another solution.

  Welcome them

• Setup does not recognize connection to printer

  have hp photomart c4180, reformatted and cant install now.  running windows 7 64 bit and I tried several times to hp Web site to download and comes to where it says device plug and it does not recognize the printer.  gone through all the troubleshooting steps and ready to throw it out the window, btw, printer works when connected to another pc.

  Hi duckhookob,

  OK, if the printer works when you connect it to another computer and then your question has to do with the USB ports on your computer does not. I suggest you contact the computer is built to solve the problems with the computer.

  HP has designed a quick and easy tool that diagnoses and solves many problems of printing, scanning and connectivity: The HP Print and Scan doctor. HP recommend you to download and install Print and scan doctor no matter what time you need to solve a problem with your HP printer from the link below.

  I would like to know what are the errors you receive?

  http://www.HP.com/go/tools