WiFi, WPA2 Personal, error

My company wireless network uses WPA2 Personal encryption. "After entering the password on the pre, it displays a message' IP Configuration error '.

Anyone encountered this?

Your company allows you to use a static ip address requires? If so, you can always rely on the network that you have selected to configure the address (after that it says the ip configuration has failed).

That said, I saw problems like that when you are too far from the access point. You can easily check putting themselves under the access point and try to connect (this isn't a solution, of course, but if the beach is indeed the question, you might want to check with HER and see if they can do something about the power of the signal or deployment). Mobile devices have smaller antennas compared to laptops...

Tags: HP Tablets

Similar Questions

  • Why is the WPA2-Personal encryption type does not when I create an Ad Hoc WiFi network?

    When I try to create an ad hoc network with WPA2-Personal encryption, then try to connect to it, it is said that he could not connect. I tried all of the devices that I have and none of them worked.

    Any help is appreciated.
    Thank you!

    Hello

    Thank you for contacting Microsoft Answers.

    Check that the devices are supported by WPA2-Personal Security? If they don't you can not use the type.

  • WiFi WPA2 on PowerBook G4 - possible?

    Hey PowerPeeps - updated my wifi router uses WPA2 Personal encryption by default (preferred); more old Powerbook G4 can deal w encryption WEP (& LEAP) only, then it rejects the attempts to connect to the wifi

    Does anyone know if there is a device or application that can help this old faithful dog make the leap to this level of security?

    I know I can go down the encryption on the router to WEP for the Powerbook (and everything else), but then security level is decreased for all my other newer devices (assuming they will work using WEP), would be so def prefer not to do

    Any help, advice or recommendations appreciated - thx! Kyle

    Solurion if you are running 10.5.x.

    http://eShop.MacSales.com/item/NewerTech/MXP3802NU2CO/

    http://eShop.MacSales.com/item/NewerTech/MXP3802NU2C/

  • Connection to a new router with WPA2 Personal

    I recently had to buy a new router - a Linksys WRT610N. It uses WPA2 Personal wireless security settings. I can't connect to wifi with my Palm T / X I have the latest version of Enterprise installed, but it is a home connection. I can't downgrade my WEP security - is there a way for it to work? Thanking all in advance...

    Oh happy day! Using the checklist as suggested work - changed from mixed to B/G setting on the router and all of a sudden, it was my network, plain as day, on my T / X - a few insertions of password and I am strong. I don't have the download of the company on my T / X and I had to go home in two other devices but it is a painless procedure otherwise. Thank you, once again. I should add that Linksys support gave me 2 different answers, a flat-out "No way." and the second "you will have to change all your settings on each device-good luck!  (not very encouraging). Palm phone support wasn't better "can't do" - I did not pay, of course.

    I'm passing this because I have an "instinct" that, despite all the negativity, I read there are some VERY bright, helpful people there voluntarily helping each other.  I hope that this post will encourage the other NOT to give up.

  • WRT54G2v1 - can't change from WEP to WPA2-Personal or Devil WPS

    Hello.  I have a router WRT54G2v1.  I set up WEP with a couple of years.  However, I want to go with WPA2-Personal for greater security.  I tried to change the WEP setting by choosing WPA2 I want in the drop-down list existing wireless > Wireless Security in the router configuration window accessed via my browser.  Immediately after that, I get the following message appears with the options "OK" and "Cancel".  The message is this:

    It will stop WPS WI - FI protected setup is not compatible WEP/WPA/WPAZ-company/Radius

    If I say 'OK', I do not then get to select something from the menu drop down.  I find myself immediately with the message each time.

    If I go into the basic settings and attempt to adjust the configuration wireless on "Manual" of the current value of "Wi - Fi Protected Setup", I get the following message (with the same options as above).  The selection of "Manual" returns immediately at the same time, thus denying me to change the setting.

    Wi - Fi Protected Setup does not support WEP/WPA/WPA2-Enterprise/RADIUS. Please use WPA/WPA2-Personal.

    So, I seem to be able to change the setting to WPA2 in WEP (or change to disabling WPS also).  Any thoughts on what is happening?  TIA.

    Hi brianborutoo. Perform a factory reset by pressing the reset button on your router for 30 seconds. Be sure to saw this power will blink to make sure that the reset was successful.  After that, powercycle your router for a minute. Try if it works. You try to browse another or another computer for insulation.

  • WPA2-Personal wireless network, which is not yet in wireless networks accessible to the general public?

    Original title: lost our connection to network WPA2-Personal wireless internet which is not even listed as an option to connect to the internet, how do solve us this problem?

    Our WPA2-Personal wireless network fails to connect to the Internet and not yet in the available networks? Is this a problem with the adapter or modem (Cox)? And how to fix this? Help!

    Hello

    Check with the manufacturer of your router Support and Forums. If the router is configured to not show

    the SSID, then it will not appear in the available list. Maybe the router must be
    reset.

    Log in to hidden networks configuration of the control panel - network and sharing Center - a
    new connection or network.

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

  • need for WPA2 Personal Mode CLI commands

    I saw this example but I need the CLI generates the GUI. Can anyone help please?

    https://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml#pers

    That's what I have to do without the GUI on a 1142N 12.4 running

    Configure in personal Mode

    The term made personal mode refers to products that are tested to be interoperable in mode PSK only of operation for authentication. This mode requires manual configuration of a PSK on the AP and clients. PSK authenticates users via a password or code identification, both the client station and the AP. No server authentication is required. A client can access the network only if the client password matches the AP password. The password also provides the numbers that TKIP or AES uses to generate an encryption key for encrypting data packets.       Personal mode is intended for SOHO environments and is not considered safe for enterprise environments. This section contains the configuration that you need to implement WPA 2 in personal mode.

    / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

    Hello

    Here are the commands for WPA2 personal mode CLI

    Configure the terminal

    dot11Radio interface 0

    encryption ciphers aes - ccm mode

    or

    encryption mode vlan ciphers aes - ccm< ---="" if="" you="" have="" multiple="">

    output

    dot11 ssid

    open authentication

    authentication-key wpa version2 management

    WPA - psk ascii

    Kind regards

    Madhuri

  • Can not get on the net via wifi apt, dns error msg

    Howdy, hey i cant get on the net with any browser through my wifi apt. I can very well with any other wifi in the range but my wifi apt has the best signal. I get a msg of DNS server and tried everything that the computer recommended to fix. Why this only happen with wifi at my complex?

    SteveAustin71,
    Thank you for visiting the Microsoft Answers community forum.

    When you say that your wifi apt, it's your own personal network or provided by a complex of apartments for the residents?  Is that what you must pay for, or is it a free hot spot?  What is you get the exact error message?  If it's your personal network in your own apartment, what type of router is and is it secure?  If it is fixed, what kind of security it uses?  Answers to these questions will help us better diagnose your problem and propose solutions.

    DNS errors can mean different things, depending on what is the exact error message, but generally means that your computer does not have the DNS information from the router or server that is supposed to provide the IP address, gateway and DNS information on the computer when you log on.

    Let us know the answers to these questions so that we can better help you.
    Thank you

    Gloria
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • WiFi WPA2 Enterprise with RADIUS - connection problem

    Hello

    I have here a new ISA 570w with the latest firmware (1.2.17).

    Anyway, I can't get wifi to work in mode WPA2 Enterprise with RADIUS authentication.

    Mode WPA2 PSK are not a problem.

    I have configured the BEAM properly and I can connect directly to him via NTRadPing without any problem. Also the test in the web interface works without any problem (see Figure 2, 3).

    The RADIUS server is a server Synology RADIUS on a Synology NAS, which is a FreeRADIUS server under the hood.

    In the settings of the ISA wireless, I put this RADIUS server for authentication (see screenshot 1, 4).

    However, I can not connect to connect to the network:

    On the iPhone (iOS 6.1.3) I get a prompt for a user name and password, but when I click on connect, it says 'connect to 'cisco3'... ". "and stays there.

    In ISA 570w newspaper, he said:

    Information

    Wireless

    MSG = add MAC station in the list of the ATU. VID = 5; MAC = 5 C: 59:48:02:78:3E;

    Information

    Wireless

    MSG = Wireless mode is a 802.11 mixed b_g_n

    When I cancel the connection attempt, he said:

    Information

    Wireless

    MSG = the Client has dissociated;

    On my Thinkpad with Windows 7 Professional I have everything configured as usual (see screenshots 5,6,7,8) but when I try to connect I do not get a command prompt where I wonder username and password, and finally the connection cannot be established (see Figure 9). Also tried with the same configuration on an another Windows 7 Pro installed costs for laptop with the same problem.

    I can't see any attempt of 570w ISA to authenticate anything in the logs of the RADIUS.

    Also the capture of network traffic on the LAN to the Synology NAS port does not show the RADIUS datagrams.

    I already disabled COP because I read that it can cause problems, but it did not help.

    Can you please suggest something else I can try?

    Thanks in advance!

    Kind regards

    Dominik

    I saw these screenshots, but that screen settings just select the button set up next to the authentication method in the section user authentication, under users.  In each of your screenshots, the RADIUS server identification number is 1, so I would also ensure that I configured the server ID RADIUS 1 that can be configured by going to users-> RADIUS servers.

    All that said, I have seen that your tests have passed and I also do not understand the point of having the RADIUS settings on other screens and then to have info ID RADIUS.  My thought is that you'd be able to pre-set RADIUS users of-> screen RADIUS servers and then select the RADIUS server ID in all other screens without having to enter the RADIUS news over and over again.  He also thinks that you could ignore the users-> screen RADIUS server and enter RADIUS information over and over again and it should work... as you set up initially.  However, based on the past experience of programming errors, I recommend configuring the ID from RADIUS server 1 under user-> RADIUS servers if you have not already... just in case where.

    Shawn Eftink
    CCNA/CCDA

    Please note all useful messages and mark the correct answers to help others looking for solutions in the community.

  • E4200 and WDTV live via wifi without DNS error?

    Someone does it, I mean EVERYONE, got a WDTV live hub to successfully connect to the E4200 via wifi without getting a DNS error?

    My system:

    E4200, fw c. 2.1.39.145204

    WDTV Live Hum, fw c. 3.08.14

    DWA-160 (Rev.) (A) usb wifi dongle fw v. 1.80

    My sony wifi equipped blueray connected to the E4200 without boredom and access the USB HDD connected to the E4200.

    Any help, suggestions, comments are welcome.


  • DeskJet 3520 wifi WPA2 compatibility

    Hello

    I would like to know if the 3520 Deskjet is compatible with WPA2 wifi security.

    The data sheet does not include the compatibility of wifi (WPA, WPA2, WEP) security.

    Thank you very much.

    Hey,.

    I understand the frustration, but I wanted to at least specify on the issue.  I have the 3510 e - all - in - one where I find myself and this model is currently connected to a WPA2 (AES) connection type.  The 3510 and 3520 have the same network with the same capabilities of networking card.

    Good luck

    Jason

  • How to delete a profile type wifi WPA2-Enterprise when delete is not available.

    I have a WPA2-Enterprise wifi Windows 7 type profile that does not allow me to remove it. The delete icon is missing and it is listed in a section of managing networks wireless named "Networks you can see." The property screen reads, "these settings are managed by your system administrator." I am the administrator of the system.

    It is a profile of wifi which at one point was configured as a WPA2-Enterprise type test, but has been restored to a type of WPA2-PSK. Not the wifi profile is unusable because it says, "the settings saved on this computer for the network do not match the requirements of the network."

    How can I delete the wifi profile and start over?

    You could try the netsh wlan command delete profiles...

    Here's the syntax...

    http://TechNet.Microsoft.com/en-us/library/dd744890 (v = ws.10) #bkmk_wlanShowProfiles

    http://TechNet.Microsoft.com/en-us/library/dd744890 (v = ws.10) #bkmk_wlanDeleteProfile

    http://sdrv.Ms/QPTtQY

    Go to Start and type cmd in the search line. Right click on cmd.exe and select run as administrator , and then run the netsh commands...

  • WiFi access limited, error: "the default gateway is not available.

    I just bought a laptop Windows 8 last December. It had been repaired twice (change the motherboard). He works all fine until last week, wifi connectivity started showing limited access. Furthermore, my IPV6 shows no access. I tried many solutions to many websites, but all will not work. Is there another way? When I trobleshoot the problem, it will show wifi Internet but when I run Google Chrome, it displays an error of internet connection. After I trobleshoot, the stated problem is "the default gateway is not available. In addition, he recovers in about 5 minutes after trobleshooting access. I need a solution as soon as possible. URGENT!  In addition, may I know what caused this do? I hope some of you can help. :(

    Dell Inspiron 7420, unique language of Windows 8

    Hi Amos,.

    I understand that your WiFi connection fails.
    According to the guidelines of the error (the default gateway is not available), there is a problem with the gateway IP address that does not connect to the internet.

    I would be grateful if you could answer the following questions:

    1. did you of recent changes made to your computer (installation of updates, device drivers)?

    2. which antivirus app do you use?

    What are the troubleshooting steps you have tried?

    Here are a few troubleshooting steps that you can try to solve this problem.

     

    Method 1: Manually assign the IP address and the default gateway and check if it works very well. Before you assign manually the IP address and the gateway by default, do
    a note of the IP address of the computer. To do this open command prompt, type ipconfig and press to enter. This displays the IP address, make a note of it.

    To manually assign the IP address and default gateway, follow these steps:
    a. in the system, right click on network icon tray. Choose the open network and sharing.

    b. click on change adapter settings

    c. right-click on the card's wireless connection and click on properties.

    d. Double click on Internet Version 4 (TCP/IPv4) Protocol and assign the IP address manually.
    Example: Old Ip address is 192.168.0.1
    Replace the IP 192.168.0.50
    e. leave the subnet mask and default gateway are the same.
    Subnet mask = 255.255.255.0
    Gateway by default, would usually 192.168.0.1 or 192.168.1.1
    f. click apply then click Ok and restart the computer and check if it helps to solve the problem.

    If the method above does not work, proceed to the next method.

    Method 2: I suggest you try the steps from the link given below:
    Wireless and wired network problems

    http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-8&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1


    If you have additional problems, please reply to this post and we will be happy to help you further.

  • No fix for the iPhone 6 WIFI "incorrect password" error?

    Was started shortly after the iOS Update 9. We have several customers experiencing the same problem with iPhones and iPads.

    Yes, we have been meticulously enter the password. We are aware that it is case-sensitive.

    Apparently, there is some sort of strange intermittent problem. My child MX5X2LL/A 6 IPhone will connect to WIFI for a week or two, and then completely to 'forget' the passwords to each wireless network unique, that it is never connected to any notification and without any warning. Then, a week or two later, miraculously connect wireless once more. This weird bug is driving us bananas - especially with all the data overages. It all seemed begins at the time of upgrade to iOS 9. Here's what we've done since September:

    • upgrade to iOS 9.1 and later 9.1 updates

    • Re-set to update to iOS 9.3.1

    • clear and reset the network settings at least 12 times

    • clear and reset the entire phone three times

    • Reset all wireless routers, change the SSID, changed passwords

    A few things that do not seem to give us at least some sort of progress, but still unacceptable:

    • people with disabilities find my iphone - connected to WIFI immediately, then he lost again a week later

    • connected to the public WIFI hotspot by Bright House, but not through WIFI interface type

    • connected to two 5G wireless networks, even if it would not connect to 2 same G network with same or different passwords

    The signal strength is great in the world. I checked all the obvious and not so obvious stuff. Running a password access point is dangerous and not an option. It is not heat, because in this case from a cold start. The only thing I can find is a difference of firmware in the authentication in the WIFI chip used on the sellers of MX5X2LL / a. are swapped mid-year model in all mobile phones, computers and tablets and is usually transparent, so there may be a problem specific to the provider, Apple is not aware of.

    Apple support has been useless and unfortunately pompous as usual, declining several times there is a problem and asking I have send my phone to paying off-warranty service or a replacement, which is NOT a solution, thank you. There are at least hundreds if not thousands of people posting here who have EXACTLY the SAME PROBLEM. My last post was removed because some Apple genius assumed somehow it's funny business going on, but I can assure you and to prove it has NOT NEVER been hacked, cracked, unlocked or jailbroken, whatever that means. Maybe they have a mandate to delete messages that indicate their equipment cannot 'some work '.

    < published by host >

    No problem on other networks that are managed professionally?

  • Have the intermittent connection when you use WiFi and conflict error IP address when using Ethernet

    I have intermittent problems with my wireless internet connection. I contacted the ISP and they analyzed the configuration of the modem-router, changed some and told me to try to reconnect. I try again and the connection is OK. The ISP has caress each other on the back and sent me on my merry way not-so-small. Problem is at an unpredictable time, problems (do) happen.

    Usually the failure scenario does not have a huge problem - plus one
    gene as a problem. I just keep trying to connect through Windows
    Network and sharing Center, and possibly the connection is made. But in some cases, time is critical; I eventually lose 10 to 20 minutes of typing-search-typing-correction-etc in a web form when the connection disappears before making a SHIPMENT. (Some time, after the failed wireless and re - connect, I was actually able to recover pretty quickly that the site has not been exceeded me.) So in this scenario I can't lost any strike.)

    I would like to connect my pc to the internet via an ethernet cable
    the modem-router. I could take this approach right after the wireless
    connection failed. Or in a preventive way, when I know I'll be typing-
    mode of research-type-fixed-etc and I want to be really sure. When I tried this, I get the error "Windows has detected an IP address conflict.

    What I do at this point to get around the Wi - Fi connection and connect through the Ethernet cable?

    The topic is edited for clarity of the moderator.* *.

    [Original title: LOST INTERMITTENT WIRELESS INTERNET CONNECTION]

    It is not clear what parameters your ISP technology management may have changed on your modem/router.  As a general rule, the ISP concerned the link between their server and your modem, but any fiddling with settings that control this link will not effect either on the link between your computer and the modem/router.

    If you still haven't reset your router to its default settings, do not unless you know the necessary internal router settings for you connect to your ISP.  If you have a cable Internet connection, the default settings may work OK, but if you have a DSL, they probably won't.

    You should not get this "IP address conflict" error when you connect the Ethernet cable.  Follow these steps:

    Open the "network and sharing Center" and then click on "change adapter settings".  You should see an icon for your wireless network adapter and an icon for your 'connection to the Local network' (your Ethernet connection).

    • Right click on each of the icons, and select 'properties '.
    • There should be a list titled "this connection uses the following items."  In this list, select "Internet Protocol Version 4 (TCP/IP)" and then click "Properties".
    • The radio buttons to "Obtain an IP address automatically" and "Obtain DNS server address automatically" should both selected.  If this is NOT the case, do so and OK your way out.  Furthermore, cancel your way.

    If a card has been configured to use a specific IP address, your "IP address conflict" should now be fixed (you may need to restart the computer for the change to take effect).

    If cards were already configured to obtain its IP address automatically, the problem lies in the configuration of your router.  You will need to access the router's Web utility to study and make changes.  To help you provide the brand and model of the router of the label on the back or the bottom.  Also do the following to a time where you have an Internet connection:

    Open a command prompt window (type cmd in the search box and press enter)

    1. In the black command prompt window, type the following command, and press ENTER after each line

    ipconfig/all > "% userprofile%\Desktop\ipinfo.txt".

    Notepad '% userprofile%\Desktop\ipinfo.txt '.

    output

    1. In the opened Notepad window, click Edit > select all (or press CTRL + A) and then click Edit > copy (or press Ctrl + C)
    2. In the body of your Question, right-click > paste (or press CTRL + V) the data of the Notepad window
    3. Close Notepad and remove ipinfo.txt from your desktop

Maybe you are looking for

  • Why is my friends and Podcasts for iOS 10 appear in my updates?

    I have iOS 9.3.2 on my iPhone and OS X.11.5 on my computer, using the latest version of iTunes (12.1.4.6) software and when I update my Apps in iTunes (under Apps-> updates) I see also find friends and Podcasts. If I try to update I tells me they re

  • Error 80070002 could not install windows SP1

    I am installing service pack 1 of windows. When I try to install it, it remains at 0% for a long time and then eventually say the installation failed with a 80070002 error code. I need help!

  • Missing appointments

    After the recent update, my work calendar shortcut has disappeared and it is not in my list of apps. I receive reminders of appointments, but I can't find the icon. My email is still there, but not the calendar. Any ideas?

  • Installation of Windows 7 on the second laptop

    first post so please bear with me. my Dell Studio 1558 running windows-7 recently deceased.  the motherboard somehow got fried.  I pulled the laptop hard disk on and recycled.  a friend gave me his old inspiron from dell (under Vista).  It is slow an

  • The creation of Oracle DB short Integrator 3.1 connection error

    Hi allI am facing a problem while creating a new connection to Oracle DB using Inegtator in version 3.1.I get the following exception:"constraint violation of the charger in the baseline interface initialization: when troubleshooting method ' oracle.