will not display the table correctly; displays OK in Internet explore all versions

Table will not correctly display in Firefox; Removes the first section of < b >... < /tr >, move the section 2 of < b >... < /tr > right. The table shows correctly in all versions of IE.

You should never use several hyphens in a comment.
Firefox will toggle the status comment after that each two hyphens (-), if you need a lot of luck with this many as in this case:

<!----------------------------------Geograhphy, etc. ------------------------------------>

Firefox treats the code that follows as comment until the next two "-" found in the next section. You can see through view > Source of Page as green comment.

<!---------------------------------- Accessibility ------------------------------------>

You're code here shows a < td > additional vacuum that causes a column empty to appear to the left, if that's what you mean.

<TR align="center">
<Font color="#ff00cc">
<Font color="#ff00cc">
<Font color="#ff00cc">

You can use the DOM Inspector to examine the code.

Tags: Firefox

Similar Questions

  • Why the SD-R6112 drive will not read the table of contents through DVD Decrypter?

    Why the hell used my reading of DVD-ROM/R/RW Toshiba SD-R6112 the TOC through DVD Decrypter?
    She normally does! I use nero, Decrypter, DVD Shrink, and even Windows medai Player 9 series.

    It was working fine 2 days ago now pfft, will not work. Everything in the settings of the device checked, said everything works properly without conflicts. I unloaded the driver and rebooted then loaded it, same problem. I tried a disk driver that came with my laptop and is responsible, it is very good, so I take this CD work correctly, but won't load DVD. With DVD Decrypter, it says: could not retrieve the table of contents.

    There must be a solution!


    Are you trying to make illegal copies of DVD? ;)

  • Color picker will not change the color correctly?

    Hi guys,.

    I have a weird problem with color. When I changed the color of dark green to bright lime green on the color picker. The color picker shows the specific color I want and then I click 'OK '. It has not changed black lime green to green light... instead it shows the dull green color. It's really listen to me because I can't figured it out what wrong with it. I checked the color (RGB mode) Mode and colors... everything seems to be good for me.

    Here is the quick screenshot:


    I also tested with another color, it still has the same problem. They do not show the bright color, it shows the dull color instead.


    I hope you guys can help out me!

    Thank you


    According to the information, you're supplyng we using the screenshot, it is very clear, you're wrong, the color Mode is CMYK and non RGB just look at you screenshot and you'll see what I mean.

    The color mode of the Document in two screenshots shows CMYK.

    The color you see is planned. Change the color correctly in RGB mode and it will solve your problem.

  • DeskJet 3510 all-in-one will not feed the paper correctly

    I have a Deskjet 3510 all-in-one and it is only about 6 months.  She went from fine print one day not to catch the paper or grab 2 or 3 pieces at a time.  Sometimes, it will sound as he begins to print and then a beep of 2 or 3 times.  Suggestions to help?

    Yes! I wasn't in the lower plate, and that's where he was suspended. Thank you!

  • Drive external HARD USB will not access the files correctly on Satellite A100-033

    I have a laptop Toshiba Satellite A100-033 (PSAANE-03J02GEN), running Windows Vista Home Basic Edition.
    I have a Western Digital passport external hard drive, which has no power source, because it pulls its power via the USB port.

    Sometimes the player works fine, but I often have huge problems to access files on the drive. Opening a folder can make Windows to hang.

    Open an audio file or a Word can do Word or audio software crash. Copy files often fails and in the process can make the Explorer Windows stop working.

    Recently I tried to copy a 33MB file from the external hard drive to my laptop, and while he did it took more than an hour. So many things can happen, none of them pleasant.

    Problems can occur if the external drive is the only device connected to a USB (apart from an external mouse, I always use), or if the external hard drive is one of a number of devices plugged into my laptop - either separately or through a USB hub (powered or unpowered).

    Anyone know what is happening and how I can make my USB external drive usable? I have two other external drives (powered by their own power source) and they work perfectly.

    Why, most of the time, do drive limp along so badly that they are virtually unusable?


    One thing is clear; the problem is definitely related to the external HARD drive and not the laptop. It seems that this problem still occurs if the HD has been connected.

    It of really difficult to say what could be wrong with your external HARD drive
    Maybe HARD drive sectors are corrupt, and therefore you can not open folders and some files stored on the HARD drive.

    Have you tried to format the HARD drive? Check this box and try to save and re-open cases.

    In the worst case that the external HARD drive has a hardware malfunction

  • Will not except the wordpad window placement... is moving all over the screen.

    I have this annoying problem... I open a wordpad document and set the widnow investment that I love and that you close the document. When I re - open the document window has shrunk and moved to another part of the screen.

    Often the window will be very small... almost half the size of my screen.

    I know that I can use the properties to maximize the window always open to but I work with several documents simultaneously and need access to my other links and expanded running does not allow this.

    Is there a way to keep the wordpad to remember the location of the window?

    And while I'm on this subject, my excel 2000 does the same thing, but it slides to the top of the screen, each opening until the title bar is off the screen (I keep my taskbar at the top).

    Thanks in advance

    Go to start / Control Panel / folder Options / display and check the box next to remember each folder view settings.  If it is already done, this obviously won't work.

    I don't know what else to think.  This should not occur and there is no settings in Wordpad to control this type of behavior (or on the desktop also).

    As far as Excel goes, try to post the question on the Excel Forum: http://social.answers.microsoft.com/Forums/en-US/excslcreate/threads where experts in Excel will be happy to help you.  Maybe this solution will solve Wordpad as well.

    I hope this helps.

    Good luck!

    Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • I'm unable to complete a download process. pop download - up appears and it seems to be downloading, but several tabs pop up and the point I'm trying to download does not show the end upward. my download using internet explore works very well

    The tab section keeps adding several tabs that I select something to download. It ends up a loop and keeps appearing as if it is the downloading of multiple copies of the same thing and I can't even get to a point where it allows me to stop the download or the closing of firefox

    See Firefox opens several times empty tabs or windows after clicking on a link

  • plugin.expose_full_path will not keep the value "false".

    I am able to change the value of the "true" to "false", but it will not retain the value 'false' to restart Firefox.

    All my plugins and extensions are uptodate. I use XP Home, also updated.

    You can check for problems with preferences and try to rename or delete the file prefs.js and possible prefs - numbered # .js and a user.js file possible to restore the values all default prefs.

  • My laptop Sony VAIO with Vista will not connect and stay connected to my wireless internet.

    My laptop Sony VAIO with Vista will not connect and stay connected to my wireless internet.  All other laptops in the House are perfectly.  Internet disconnects, says local only, then reconnects constantly making internet hard work.

    Hi Tinkerbellfancolorado,

    1. When is this last work fine?
    2. Do you receive an error message or error codes?
    3. Recent changes on the computer?

    There could be several causes for this problem.

    Try starting with these methods.

    Method 1

    Step 1

    1. Open Network Diagnostics by right-clicking the network icon in the notification area, and then click diagnose and repair.
    2. Make sure that all cables are connected (for example, make sure that your modem is connected to a working jack or cable phone connection, either directly or through a router).
    3. Reset your modem and router. Remove the power cord from the modem or router, wait at least 10 seconds, then plug in the modem and/or router back.

    Step 2

    Another reason may be windows disable your network adapter to save power. Turn off the power saving option in the properties of the network (wired network only cards) card:

    1. Open network connections by clicking the Start button, clicking Control Panel, clicking network and Internet, click network and sharing Center, and then clicking manage network connections.
    2. Right-click on the connection and then click Properties. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
    3. On the Networking tab, click Configure.
    4. On the power management tab, clear the allow the computer to turn off this device to save power option, and then click OK.


    Method 2

    Temporarily disable the firewall, and check the status.

    NOTE: To re-enable the firewall after check you the status. If you are connected to the Internet or a network during the time that your /firewall antivirus software is disabled, your computer is vulnerable to attacks.


    Hope that was heloful.

    Bindu S - Microsoft Support
    Visit our Microsoft answers feedback Forum and let us know what you think

  • "Non-rectangular objects will not display correctly when you export with the help of CSS."

    I use Ind CC 2014 export a document to an epub recomposable.  The document contains a picture .ai.  The image export correctly in some parts of the the.epub, but not others, when it is deformed. There is a warning on export: "Non-rectangular objects will not display correctly when you export using CSS."  Any suggestion is appreciated.


    For these objects, the best option is to 'rasterize container"to preserve appearance of the page layout setting in the Options of the Export Object dialog box and then export to EPUB recomposable.

    Kind regards


  • My Muse site will not display the customized html images that work in chrome?

    My Muse site will not display the customized html images that work in chrome? Here's my url www.simplesites.com.au.

    Works fine here on Linux.

    Note that the uploads has 'ads' in name and come from simplesites.net.au, so be sure that content blockers not get triggered.

  • Firefox will not display on the screen even though with Process Explorer, I see active Firefox.exe but no CPU usage

    I use Firefox as default browser v10.0.2 on Dell XPS8300 Intel Core i5 and Windows 7 Ultimate and Compaq Presario CQ57 IO IO Intel Core i3 and Windows 7 Home. More frequently on the (approximately 90% of attempts) that Dell (50% of attempts) Firefox will not display on the screen when I click the icon. Cannot display other programs when it happens. I expressly say display because I believe that Firefox has started. To work around the problem, I installed Process Explorer on both machines and launch this program first, then click on the Firefox icon. When the problem occurs I see process Firefox.exe in the list of processes; some CPU consumed but, then, no CPU activity. If I click on the Firefox icon, yet another process opens in the list of processes, but with the same answer - some consumed CPU and then no CPU activity. If I have 2 processes running and kill the process from the 1st, the 2nd poster and then everything is normal. If I do not open it treat a 2nd, but kill the 1st process then click the Firefox Firefox is displayed and all then is normal. This problem has occurred since the original on the two new machines installation. I have updated the video drivers on both computers.

    OK, let's see if we can solve this problem and make it work for you!

    First of all, if you start Firefox in safe mode (restart your computer first, then when you open Firefox, hold down the SHIFT key) it starts more reliable? This is usually caused by a defective module. If this does not help, then restart Firefox, go to the Firefox, then add-ons button and disable your extensions one by one until you find the troublemaker.

    Also, try to update to Firefox 11, it has several bug fixes that might make life easier here.

    Just as a few troubleshooting steps base to ensure that we have all the bases covered,
    Run all Windows updates, install all required service packs, etc.

    Update all of your plugins (Flash, Java, etc.): http://www.mozilla.org/plugincheck/.

    Download and install MalwareBytes Anti-Malware, run a full scan. http://www.malwarebytes.org/. This check allows that there is no virus on your computer, causing problems. You can uninstall this program after having cleaned the infections.

  • I had a paper get stuck in my printer 1310 series. I disabled the jam but it is still showing as a paper jam and will not display 6 documents in the queue

    I had a paper get stuck in my printer 1310 series. I disabled the jam but it is still showing as a paper jam and will not display 6 documents in the queue

    If it still shows paper jam and you know that there is no paper, just turn it works, and it should realize that there is no paper.

  • Sidebar calendar gadget will not display the months or days - my Recycle Bin icon is not on my desk

    Original title: Calendar Sidebar Gadget / recycle Logo

    I added calendar Sidebar Gadget - it worked very well for years and suddenly the firm timetable.  It will not display the months or days and I can not open the pages.  That's happened?

    Recycle the icon was on the desk, but disappeared and has left a space on the desktop.  How to get back in place on the desktop?
    I hope someone can help.  Thank you.   Jeanne

    Hi Jeanne,

    Take a look at the answer provided in nets below the link to solve your problem in calendar view:
    My Microsoft calendar gadget is displays a blank page, rather than the current date / month calendar

    Then try to use the Microsoft Fix It provided in the link below to get the trash on the desktop:
    How can I make the Recycle Bin on my desktop in Windows Vista or Windows XP?

    Hope that helps.

  • Vista will not display description of the file on mouse over. File name, Type, size, and Date modified see the upward, but no description.

    Vista will not display description of the file on mouse over. When I mouse over, a pop-up window displays showing: file name, Type, size and Date of change, however, it does not show the description of the file.

    So, for example if I have 5 files on different types of screw - the description tells me that the size of the screws. IE. 1.5 mm or 1. 8 mm.

    Update: try to get the description of the file displayed messing around in the file properties, now out of 10 records, only 2 includes the name of the file in the mice on the pop-up window. So now what lack us, it's the file name and the Description file.
    Help, please...

    Description of the file in as long as this is not one of the available variables, which can be shown with ToolTips - but there are others who could easily serve the same purpose. Here are the options:

    To write

    Here is an article on how to change what is shown. http://www.ghacks.net/2008/02/10/customize-windows-explorer-tooltips/ . It is to change the registry, make sure you so first back it up before doing anything so that you can recover in case you make a mistake (or do the right thing, but it does not work as expected). http://www.instant-registry-fixes.org/how-to-backup-windows-vista-registry/ .

    I hope this helps.

    Good luck! Lorien - MCSA/MCSE/network + / A +.

Maybe you are looking for

  • features of iOS 9.3 not visible

    am running on ios 9.3 on my iphone 4s, but I don't see any 9.3 features including the night shift. In addition to that my iphone eats a lot of wifi data whn I connect the charger


    I want to update my card mother p6610f so that I can install a processor AMD 8350 what changes are what I should do and what motherboards do you suggest?

  • Make a graph that is customized by using the motion of the instrument and in real time

    I am very new to LabVIEW and I need to make a graph or a table with the data being the movement of a device and the x data in real time.  I know how to get the position of the instrument information and how to put in real time for the x axis, but I h

  • How can I change the format of a film shot in Microsoft Movie Maker?

    Help! Windows Movie Maker: convert a file How can I change the format of a movie in movie maker from microsoft so that it can be universally accessed? or uploaded to youtube?

  • multithreaded Simulator

    Hi all. Not sure if this is the right place for this kind of question. If it is not, please direct me in the right way. In any case, I make an application test that will never run real device. This application don't calculation heavy and lasts approx