will not get paper

Try to put in place. The paper is in the tray, but the machine keeps telling me to load paper and press ok.

Solved.

Tags: HP Printers

Similar Questions

  • HP F4480: PRINTER F4480 WILL NOT POWER PAPER - TO NEAR EMPTY INK LEVEL

    Hi, the book in my HP F4480 printer will not feed. The ink cartridges are nearly empty, if not empty. Weak cartridges prevent the printer from paper making to finish a job, or is it likely another question?

    Hi @80Printer,.

    Thank you for joining the HP Forums!

    I have seen your post on how your HP Deskjet F4480 printer will not feed paper. I'm happy to help you!

    Low ink cartridges can certainly be the cause of not feed paper. I recommend that you replace the ink first and see if that solves the problem. If it does not solve the problem, go through this guide, 'on paper' Error Message on the computer and the printer is not Pick Up or paper feedand let me know what happens!

    Don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

    Hope this information is useful and thanks for posting!

  • hp8550 will not feed paper

    My Hp 8550 stopped feding paper. What can cause this?

    my printer will not feed paper into the printer.  He just left.  What's wrong?

  • I went to Adobe Creative cloud to install Bridge. I pressed the button download next to the bridge and my creative cloud now says "update installation...". "but the sequence is at 0% and will not get above. Please help me, thanks

    I went to Adobe Creative cloud to install Bridge. I pressed the button download next to the bridge and my creative cloud now says "update installation...". "but the sequence is at 0% and will not get above. Please help me thank you all

    Hello

    Please quit Setup and then exit the creative application of cloud.

    After that, restart the machine.

    Let us know if that helps.

    Kind regards

    Bani

  • How can I add a footer to the main section that will not get push off-page?

    Generator 10.1.2.2.0
    ORACLE Server Release 10.1.0.5.0
    Oracle9i Enterprise Edition Release 9.2.0.8.0 - 64 bit Production

    Hi all

    I want to add a footer frame in the main section of a report that will not get pushed off the page by an extensible framework above it, which can develop vertically, but will still allow the extensible framework continue on the next page (and print another foot on this page as well. I paint a blank on how to do it with anchor or frameworks encompassing etc points.

    Extend the extensible framework until the footer frame. Change the elasticity vertical expandable framework to contract or fixed. In this case, pull-out frame will be printed until the foot of the page and will then continue on the next page.

    I hope this helps.

  • ENVY 100 all-in-one: Envy 100 printer all-in-one - will not glossy paper 250 gsm

    Difficulties that the printer will not accept 250 gsm paper past the printhead.

    Followed him orders for cleaning rollers, reset by disconnecting the power and brought etc. cartridges.

    I note others have had the same problem which seems to have been set by a semi of hardware reset. How can I get the required for the semi reset procedure?

    Thanks in advance.

    Welcome to the @noxasforums.

    I saw your post about your Envy 100 not pulling by glossy paper 250 gsm and wanted to answer you! I checked the specs for the Envy 100 and as you can see below, the printer should take in if you use a format supported below. Maybe you can try the steps from the link I posted for you. I think the cleaning rollers should help. You can also try to select different types of paper to see if one works better than the other.

    Let me know what happens!

    Tip: Make sure that the printer is plugged directly into a wall jack, avoiding bars power and surge protectors. This ensures that the printer is full on.

    Testify of my answer by pressing the thumb in the air below and hit the "accept as Solution" button, if I have you helped a resolution!

    Good luck!

  • Will not get my Acer iconia 7 b1-730hd past Acer logo when I try to start. Any help, it was beautiful!

    I was reading on my Tablet and started to get flashes of Google has stopped playing and different applications, then they say something about the pitcher and he quit. When I tried to revisit the logo Acer turns on and it will not go to the lock screen. I even let it go until the battery is dead and the tried and the same thing! Help! Please, I beg you! Thank you

    Try the solution:

    https://community.Acer.com/T5/Android-tablets/need-help-Acer-B1-730HD-stuck-on-USB-logo/m-p/318495

  • 2nd computer on the wireless network will not get on the internet

    my computer is xp my 2nd computer is vista through the wireless receiver dlink615 and dlink. is on the network but will not go to any willing internet change workgroups the same two as said is on network and said to the internet, but where to go to get on it turns at the local level only

    Hello

    Please make sure that your services are working very well and started, has not stopped.
    1 wireless zero configuration
    2 Server
    3 workstation
    4 Netlogon
    You can find these services, start > run > type services.msc then, a window will open, check for these services if they are running, then there should be no problem with internet.
    If all services are working correctly, then give IP addresses to your PC manually according to the parameters provided by your ISP or registration of your ADSL modem.
    Hope this solve your problem...
    Thank you
  • Can't reinstall Vista. Because Vista will not get to the Setup screen.

    Hi people. Got a prob a little. Vista stopped booting the other night. So, I tried safe mode, and it hung on crcdisk.sys. So, I decided to get in shape. Problem is, it will boot from the DVD, but will not load / access the Setup screen (I waited for 7-8 minutes and nothing's happened, shows just the thing with the green bar).

    Not too sure if it's because the hard drive is 1 TB (but Vista was on the same front hdd with Windows 7). I tried to remove the 2 GB of ram (I use 4). No go. Tried another DVD rom, not go. Removed USB devices that have been connected. No go. I know that the DVD itself is fine. I tried on the other PC here, the installation screen came within 2-3 minutes. But his is not a 1 to (its 250 GB) the only DVD that will work / I install is the Windows 7 DVD.  So, how can I reinstall Vista?

    I deleted all partitions / recreated with the Win7 installation as well. Still couldn't get Vista to get to the Setup screen

    Any info appreciated

    Thank you

    Finally fixed it. I read that USB legacy can also cause this. So, I disabled it. Everything is good. Managed to get to the Setup screen, then reinstall Vista

  • Pavilion HPE-552SC: HPE-552SC and ASUS GTX750TI - will not get past the BIOS

    Hello.

    My installed shipped with the HPE-552SC has failed and I bought a new ASUS GForce GTX 750TI. After installing, the computer will not exceed BIOS.

    Looking at some of the messages in the support forums, solutions would be to turn off the UEFI - how ever when I press "ESC" at the start of the BIOS, I can not run the application "Run Application UEFI" - see photo below.

    BIOS is updated to 7.15.

    What should do?

    Best regards

    Andrée

    Hello

    The NVIDIA GTX 750TI requires a BIOS to version 8 HP with a few exceptions depending on the graphics card.  Your PC is four years, so don't expect HP to publish a version 8 BIOS.

    The NVIDIA GTX 660 or 660 TI would be a good choice.  You may need to upgrade the power supply according to the map.

  • EA6500 will not get the rental

    Small business, under 10 computers, printers Wi-wired and wireless, simple network. Don't no need (nor yours especially) Smart Wi - Fi, Cloud Connect, or or anything other than a simple router configuration manually. Have a new EA6500 I intend to use in replacing an E1000 who plays up (must be reset to zero every morning) connection to Verizon East (former GTE) aDSL. Connected the EA6500 to a laptop via ethernet, router password changed even as E100, put in place redirects it two port I need (IP addresses on the internal network are static in the 192.168.1.0/24 block), DHCP server changed to start at 101 (don't ask), leave the Type of Internet Connetion setting "Automatic Configuration - DHCP" (the same as E1000) close the two routers and modem (Westell 890-210015-04 wire speed). Connect to EA6500 for modem, turn on the modem, router, switch and...

    Nothing. Not getting any external IP address via DHCP.

    If I switch back to the E1000, it immediately picks up the lease of the IP.

    So what hurts?

    No, I can't use PPPoE (former GTE is DHCP, as I mentioned), no, I have no intention to replace a modem to work when it has nothing to do with the problem, I need to clone the MAC address.

    The solution was simple, and the problem (I suspect and implicit in my original post) was my mistake. I simply forgot to release the lease on the old router before attempting to obtain a lease on the EA6500. Tested with my home system (to avoid downtime in the shop) and the EA6500 cheerfully acquired a DHCP lease on my home DSL after I published the lease on my DD - WRT router.

    Of course, to get the EA6500 to release the lease so I could return to my router has been a nightmare, with the flaw in the firmware (more precisely, the pride of programmers) who does not have an exit without renewing. Had the time tearing the WAN cable (oh, just, Cisco calls an 'Internet' cable) on the modem shortly after hitting the 'release and renew' link - took a few tries, but eventually caught after the release, but before he could renew selfishly.

  • Downloads from Amazon will not get the error C00D36B4

    Download will not play have redownloaded will not play again. Play previous download from amazon

    What the file type of these downloads (MP3, WMA, WAV...)?

    What is the full text of the error message? If you click Web help, what is the URL of the web page you need?

  • HP officejet 4652: will not hold paper printer-get message paper

    Get message "on paper" don't shoot the sheet in the printer printer 4652

    Hi @jb19431,

    Thank you for reaching out to the forums! I understand that you get the message 'out of paper '. I'd love to help you.

    I'd try step 4 of this document for cleaning of the flow of the rollers and step 5: reset the printer: paper jam error.

    If the problem is resolved and that you appreciate my help, please click on the button "Accept as Solution" and the "Thumbs Up". Let me know how make you out. See you soon!

  • Backflip in Latin America will not get updated!

    is it possible that used to make us also?

    @shak2blessed,.

    As you can see on the same page which States that Latin Americans backflip will get the update, U.S. backflip will receive it. Do not worry

  • I get a message to run chkdsk and chkdsk will not get to 62% and then goes no further

    Original title: Please help someone!

    Hi I keep getting a message to run Chkdsk because I have a corrupted file, but it doesn't get to 62% verified and is not further after hours of weaiting, what this could be and what I can do to remedy this? anyone?

    ... e-mail * address email is removed from the privacy *.

    Hi I keep getting a message to run Chkdsk because I have a corrupted file, but it doesn't get to 62% verified and is not further after hours of weaiting, what this could be and what I can do to remedy this? anyone?

    ... e-mail * address email is removed from the privacy *.

    Hey, Janice.

    First of all, I want to repeat that a question is necessary and please help someone! is not in the form of a question.  This type of posts get ignored.

    http://support.Microsoft.com/kb/555375

    Start > type the word: Smart

    Select the smart Test

    It will take a few moments to run the test.

    Disable System Restore - malware is known to hide in the restore points

    http://www.howtogeek.com/HOWTO/Windows-Vista/disable-System-Restore-in-Windows-Vista/

    Have you scanned for viruses/malware when it started?  If this is not the case, download the following and a scan of your system.

    Malicious software removal tool

    http://www.Microsoft.com/security/PC-Security/Malware-removal.aspx - or -

    TrendMicro Housecalls

    http://housecall.trendmicro.com/

    When you see this message, exactly what are the steps you take?

    What is the make and model of your computer?

    You have scheduled a chkdsk scan in the past?

    Try the following:

    Right-click on command prompt and select run as administrator

    Type: chkdsk /f /r

    Press enter

    You will receive a message:

    Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts? (Y/N)

    Press y and press ENTER to schedule the disk check on startup

    Note: /f: corrects errors on the disk.

    /r : Locates bad sectors and recovers readable information.

    If you had already scheduled a chkdsk which stagnates and reboots at startup, and then follow the instructions in the link below.

    How to cancel chkdsk after it was planned

    http://support.Microsoft.com/kb/158675/en-us

    Here is a link to a fix:

    If the CHKDSK program runs every time you start, regardless whether the analysis was carried out or not, and there is no error message, it may be the result of a known problem between Windows 7 and the infrared device integrated on the laptop.

    http://bizsupport1.Austin.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&TaskID=110&prodSeriesId=4247653&prodTypeId=321957&prodSeriesId=4247653&ObjectID=c02178031

    The chkdsk program does not start successfully on a Windows 7 computer

    http://support.Microsoft.com/kb/975778/en-us

Maybe you are looking for