Windows 7 does not recognize scanner HP PSC 500 all-in-one

Similar Questions

• Windows XP does not recognize Portable Toshiba external 500 GB hard drive.

  I bought a Toshiba Portable external 500 GB hard and connected to my Windows XP. My windows XP will recognize any unit. I went into my computer > management > drivers to find the drive and rename it. He wasn't there. I have Windows XP SP2, and I said that Windows XP SP3 is not compatible with this device.  I went to control panel > adding hardware > allow Research Assistant for devices not installed and it still did not.

  Any suggestions?

  In the future, please start your own thread.  It does not appear that your problem has much in common with that of the previous, other than you poster, both have a problem with an external drive.

  Open disk management (start > run > diskmgmt.msc > OK)
  Your portable player should be shown here (probably as "disk 1" in the lower pane)

  

  If the disk space presents itself as "Not allocated" (as in the figure above), right-click and select "New Partition".  During the operation of the wizard, you assign a drive letter.  I suggest that your format using NTFS.  Once the disk has been partitioned, formatted, and has a drive letter, it should show in my computer.

  If the drive is already partitioned and formatted, see if you can assign a drive letter to right-clicked on.

• HP Solution Center does not see scanner (HP Photosmart C8180 All in one)

  Solutions of HP on my L:aptop will not see the scanner HP Photosmart C8180 printer.

  I can print from the laptop and my desktop computer sees the thin printer using HP solutions (same printer same router/network).

  It is a problem that has occurred before. I put on the day of Vista to Windows 7 and re-installed the program, and if I remember correctly it was working fine.

  It has now stopped working again.

  I just had to re - install the printer because it does not appear in the folder devices and printers.

  Hi DavidSK11,

  It uses a USB connection or network?  You install by using the drivers from the HP website?

  Here is a link to the driver for Win7

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-76036-1&CC=US&DLC=en&LC=en&os=4063&Product=3204788&sw_lang=

• Windows 7 does not recognize scanner Canon DR - 2580C, even after the installation of the driver

  How can I fix it?

  Hello

  1. deal with any problem with other USB devices?
  2. have you tried to connect the scanner on a different USB Port?

  I suggest you to try the steps and check.

  Method 1: You can run the corner hardware store and check.

  Open the hardware and devices Troubleshooter:
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:
  If the problem persists, you can try the procedure described in the link and check.

   

  Working with the scanner and Camera Installation Wizard
  http://Windows.Microsoft.com/en-us/Windows7/working-with-the-scanner-and-Camera-Installation-Wizard

  Method 3:
  If the problem persists, you can select the correct operating system version and try to install the drivers and software provided in the following link:

  http://www.USA.Canon.com/Cusa/support/consumer/scanners/document_scanners/imageformula_dr_2580c_compact_color_scanner#DriversAndSoftware

   

  If the problem persists I suggest you to contact Canon Support.
  http://www.Canon.com/support/

  I hope this information helps!

• Windows XP does not recognize the full HD 500 GB

  I have an old version of XP Pro. My HD crashed & installed 500 GB HD sees now only 128GB. BIOS sees 500 GB. I haven't made windows to & including SP3 updates still no change. What is the solution?

  Windows XP RTM can format only up to 128 GB - it took until SP1 (?) that the formatting of the larger disks was available during the installation.

  Your HD will have a large part of the unallocated space - you should be able to create a second partition using all that space, now that you have installed SP3.

  If you want a single system partition, then you need to extend the existing partition by using third-party tools or use a CD Pack of Service higher for installation.

• WINDOWS 8 DOES NOT RECOGNIZE THE SCANNER OFFICE HP OFFICEJET 4500

  MY WINDOWS 8 DOES NOT RECOGNIZE SCANNER OFFICE OF HP OFFICEJET 4500

  Hello

  1. don't you get any error message when the scanner not detected?

  2. do you insert scanner in another port of the computer or to another computer?

  3. were there any changes (hardware or software) to the computer before the show?

  4. other recognized devices?

  If your computer is having problems with a recently installed device or other hardware, try to use the hardware and peripheral troubleshooting tool to solve the problem. It checks the common issues of interest and ensures that a new device or hardware connected to your computer has been installed correctly.

  Run the hardware and devices Troubleshooter and see if it helps.

  a: press the logo Windows + O to open the search box.
  b: Type Troubleshooting, press on enter.
  c: now click material and its.
  d: now click hardware and devices , and then click Next 

  Answer please if you have any questions.

• Install Windows 8 does not recognize the system drive

  I built a new machine (chart below). Since this is a new machine and not an upgrade, I bought Win 8 Pro 64 bit OEM to do a clean install. The SSD is my system disk that Windows 8 will be installed. Four data drives are mirrored, two for the other two. Construction went perfectly. The BIOS recognizes all six disks: 1 SSD, 4 HDD, 1 DVD.

  Insert and boot the disk of Windows 8. Accept the EULA, enter the product key. Arriving at the page "Where do you want to install Windows?", only four hard disks are listed. The SSD (installation to go) is not found by Win 8. ??? I tried to change ports SATA, cables, power supply - no difference. For each new change of hardware, the BIOS still sees everything. This isn't a hardware problem.

  The question remains: why the installation of Windows 8 does not recognize the SSD drive. All five disks are on AHCI. I'm not in RAID.

  I spoke with crucial technical support of all (manufacturer of the SSD). They were also surprised that the drive does not appear in the list.

  Does anyone have a solution? I spent all the money on hardware, as well as the new version of Windows and I cannot install it.

  This is the real kick in the teeth: Microsoft won't support me. The OEM of Windows 8 version is the same as manufacturers, such as Dell or HP. Support told me I had the support of the manufacturer. HA! I am the manufacturer. Either that or upgrade from an earlier version of Windows. This means that any that a new construction machine will get ZERO assumption of Microsoft. All just great.

  Thank you in advance for any assistance.

  Windows 8 Pro 64-bit (full version) - OEM
  Intel Core i5 - 3570K
  Card mother GIGABYTE GA-Z77X-UD5H
  Crucial Ballistix 2 x 8 GB DDR3 1600
  Crucial M4 2.5 "128 GB SSD (system disk)
  WD Green WD30EZRX x 4 (data readers) 3 TB drive
  Rosewill Challenger-U3 ATX Mid Tower Case
  SeaSonic M12II 620W 620 Bronze PSU
  ASUS DVD writer

  The DSS must be LOW LEVEL FORMATE.

  Once, there may be no other [HDDs] not connected to the SATA ports.

  Install Windows 8 Pro now.

  [Edit] Can someone please mark this as answered? I can't because I posted the question. Thank you.

• Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Disconnect all USB storage.

  Run this tool by do right click and choose 'run as administrator '.

  Of course, all first extract it:

  http://www.Uwe-Sieber.de/files/drivecleanup.zip

  If your XP is 32 bits, use the Win32 folder.

  Reset.

  If you still can't find the drive, assign it a drive letter in disk management.

• Windows xp does not recognize the hp c6180 photosmart printer

  My windows xp does not recognize my hp c6180 photosmart printer

  Hello

  1. were you able to use the same printer without any problems before?
  2. don't you make changes on the computer before this problem?
  3. you receive an error message?

  See the following articles that may help you resolve this problem.
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Resources for the resolution of the printer in Windows XP problems
  http://support.Microsoft.com/kb/308028

• Windows XP does not recognize the Sony Walkman NWZ-E344 media player Red

  original title: Sony Walkman NWZ-E344 Media Player Red

  My Windows XP does not recognize my Walkman when installed in USB. All other computers do, then only, assumes that I do not have good pilot.

  Hi brumbybrat,

   

  You must install the drivers for the walkman to recognize.

   

  More information is available in the following links:

   

  Is there a CD of installation for the Walkman® player?

   

  How to install manual and the Content Transfer software for the Walkman® player

• Windows 7 does not recognize my external screen.

  Windows 7 does not recognize my external screen.  I checked the driver and even of the went to the NVIDIA site and plugged my material for my graphics card ID to get the correct driver and yet, it does not recognize it!  So here's what I have right now since I've upgraded to Windows 7 Ultimate edition = Standard VGA graphics card.  If someone has a legitimate solution to this problem, feel free to comment! Thank you

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows Vista does not recognize my Ipod Touch

  Windows Vista does not recognize my Ipod at all. He even appears in Device Manager. I know that is not my USB cable because it is new, and it isn't my Ipod because it works on Mac computers. I just need someone with expertise to help me get my computer to recognize my Ipod so I can go back to enjoy my music.

  Hello

  MTP mode for WMP11 sync - mode MSC to treat the MP3 as a reader. So you have set up in the MTP.

  -----------------------------------------
  If necessary:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Make sure that Windows is updated appropriately that there have been several USB updates.

  1 check that the driver letters for them, for a player, if the drive of the default drive letter is changed, what is happening.
  Mine was h: I added a device that took H: and the player stopped. So I put it back to H: and the other
  device to J: and everything worked again. If necessary start - type in the area of research-> disk management find top
  -Right-click on it - RUN AS ADMIN

  Don't forget to remember the MP3 must be set to the PSG to sync with WMP, and meteorological service of Canada to copy and delete files
  and update the firmware.

  If no joy follow these steps:

  You may need a powered hub. (all the USB ports on your computer are not powered, often only 2)

  Try these:

  Make a Restore Point

  Control Panel - Device Manager - click in the empty area - VIEW - show hidden devices

  Here, your devices are the MP3 player.

  Now look everywhere EXCEPT the USB controllers for your devices (cannot be found) and if you find
  It RIGHT CLICK and UNINSTALL all.

  now go to the USB and UNINSTALL ALL controllers in the category, but the category itself.

  APPLY/OK

  RESET

  This refresh battery USB and hopefully it will allow the unit to install. (You may need a powered hub)

  Here is the similar procedure under XP, Vista is the same, except that we need clear specific devices, as appropriate.
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer, as well as all USB devices that you previously used. Run Options and check the 1st three choices to see if one is there.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Windows 7 does not recognize my iphone

  After you download the photos on my iphone, windows 7 does not recognize my iphone. in other words when I open my computer the iphnoe isn't here; but in Panel, in devices and printers, it appears with unspecified Apple Mobile Device USB driver, in the form of a generic icon.

  When I run Auto Play in the search box; the iphone is there with the icon to the right, but there is no screen options menu. It behaves as if it were invisible.

  It is important to note that this started AFTER downloading the pictures for the first time. Until windows has always recognized my camera properly.

  Thanks in advance for any help.

  Here's your solution:

  iPhone or iPod is not correctly recognized by computer when USB drivers are not installed properly or are out of date
  http://support.Apple.com/kb/TS1538

  Follow all the methods in the order that they are listed. The above article helped a lot of people the question of fixing with iPod/iPhone not getting detected do not.

  See you soon! "That's all a pension chequer nights and days,"
  Where destiny with men for pieces plays;
  Here and there, mates and kills.

  In a world without walls and fences, who needs windows and doors? Life sucks! Getting used to!

• Windows 7 does not recognize my color and barnes noble nook

  Windows 7 does not recognize my color and barnes noble nook.  It recognizes my external WD hard drive, but when I plug my nook, plug-and-play do not come and tell me that he has found a new device.

  How can I solve this problem?

  Angi

  ______________________

  My personal website:
  Absolutely of Angi
  http://absolutelyangi.com
  _________________________

  Dell Inspiron 530
  OS version: Microsoft Windows 7 Home Premium, Service Pack 1, 32-bit
  Processor: Intel (r) Core (TM) 2 CPU Quad Q6600 @ 2.40 GHz, x 64 family 6
  Model 15 Stepping 11 processor Count: 4
  RAM: Mb 3061
  Graphics card: Intel (r) G33/G31 Express Chipset Family, 256 MB
  Hard disks: C: Total - Mo 476929, Free - Mo 349361;
  Total I: - Mo 476937, Free - Mo 363385;
  Motherboard: Dell Inc., 0FM586, CN736048B800IW.
  Antivirus: Kaspersky Internet Security 2011 - 11.0.2.556

  Look at this thread, third substantive post.

  http://bookclubs.barnesandnoble.com/T5/nook-technical-support/win-7-won-t-recognize-nook/m-p/694110/message-UID/694110#U694110

• Windows 7 does not recognize the graphics cards

  I have been using the same PC for the last six years of the game without any problem, I upgraded to Windows 10 and things went to * a few days after talking to Microsoft Care I was told that with the latest version of Windows 10 updates and other updates my system is no longer compatible with Windows 10 and I did a clean install to Windows 7. now, Windows 7 does not recognize my graphics cards 2 x 'GeForce GTX 480"with SLI configuration.

  In "Device Manager", it shows two units operating as VGA standard with no details etc.

  It install drivers for the 'GeForce GTX 480"because it does not recognize their being there.

  Any ideas or help... Please also stay simple for a non PC Geek

  No problem if nothing else, you've found the system images is now with win-10 days worth being pushed m main $ :)

  It of free and worth to be using,

  http://www.Macrium.com/reflectfree.aspx