Windows 7 does not start after the installation of updates - sounds familiar!

Similar Questions

• Windows XP does not start after the installation of an SSD.

  Windows XP SP3 and Intel Smart Response Technology

  Recently, I built a new computer and installed Windows XP Pro and Windows 7 Pro in a dual-boot arrangement.  Everything worked very well.  I then installed an SSD in the hopes of using the Intel Smart Response Technology (SRT) to speed things up.

  I shut down the computer, installed the SSD, brought up in Win7 and follow the easy guests in SRT to activate the player.  Restarted several times and things SSD speed up significantly.  Wonderful.
  I so restart and select Windows XP so I can SRT it.  After you select Windows XP in the boot menu, a few seconds and I get a quick flash of a BSOD and the computer restarts spontaneously.  I can't enter in WinXP, not even without failure or last known good config Mode.
  I again in Win7 and disable the SRT, reboot and I can enter Windows XP very well.  So obviously WinXP has a problem with the SRT is activated outside the XP.  That being said, I can't activate SRT in WinXP first either.  "Accelerate" option does not appear in the menu.
  Any ideas on that?
  Thanks for your help!
  -Matt

  Hello

  In these cases, we always recommend to update the system BIOS of motherboard, update the firmware of the controller RAID and disks installed. If the problem persists, you will need to fix the compatibility problem directly with the manufacturer of the motherboard and add it to the RAID controller itself.

  I suggest you to contact Intel support site to improve assistance on the issue.

  http://www.Intel.com/p/en_US/support?IID=HDR+support

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  See also:

  http://download.Intel.com/support/chipsets/SB/intel_smart_response_technology_user_guide.PDF

• Windows XP does not start after the installation of 3 GB of RAM. Will start with only 2 GB or less.

  I installed the new RAM on my desktop Compaq EVO D500.  Everything was working fine until 2 GB.  When I tried to install no matter what the computer does not start.  Specifications of the computer say maximum RAM is 3 GB.  All the memory and are good because I swapped taken in all the combinations possible and memory.  Any ideas. gknapp_ny

  If their were any memory related settings that had to be changed I would have no idea how do.  I had initially 512 MB of RAM (256-2 sticks).  I added a stick of 1 GB aditional third availabel taking and all went well.  Then I had two more identical 1 GB sticks and added them one at a time.  With 2 GB without problem.  But with the third stick of 1 GB that I couldn't start - I just beeps. I swapped one of the sticks of 1 GB for an old 256 MB and still no start just beeps.  When I run 2 GB everything is fine.  The BIOS recognizes the 2 GB of RAM. gknapp_ny

  Sounds as if your BIOS will not identify no matter what says the spec, 3 GB.

  It seems as if you may need a BIOS update in order to recognize the 3 GB of RAM - especially if it is a very old Compaq Evo D500.  See the "Improvements" tab to the page linked below.

  See http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=96295&swItem=PSG_I15378-37635&prodNameId=97121&swEnvOID=1093&swLang=13&taskId=135&mode=3

  Note that the patch on the link above is for models Evo D500 "with a ROM family 686Y2."  Read the "Release Notes" on this page to determine if your machine is one of those and if so, see "Instructions of Installation" to install the upgrade.  If your D500 is a laptop, you should Flash the ROM ONLY (i.e., update the BIOS level) when the computer is plugged - loss of power during this process can potentially cause irreparable harm to the computer.

• ENVY M6 - 1184ca: 8.1 for Windows does not start after the installation of update KB2919355

  Updating Windows 8.1 KB2919355 has proved to be extremely problematic for me. When he was released at the beginning of 2014 that I was not able to get installed it with the exception of two occasions, the first being several months ago and the second time, a few days ago. I have constant pain to try to get the update of KB2919355 until recently. What finally got the update installed was opened as administrator command prompt and type the following commands,

  DISM/Online/Remove - Package PackageNameackage_for_KB2919355 ~ 31bf3856ad364e35 ~ amd64 ~ ~ 6.3.1.14 

  and then

  DISM / online/cleanup-image /startcomponentcleanup

  So now, the update of KB2919355 has been installed. Only one problem: like the first time I had the installed, Windows Update leave commissioning. As the HP splash screen that normally appears during the startup process appears after about 3 seconds, Windows displays an error Stop, and for a fraction of a second will display SYSTEM_THREAD_EXCEPTION_NOT_HANDLED error, which as I read, is related to the graphics drivers. The thing is, after the cancellation of the update (the computer in Mode safe start put Windows automatically uninstall the update and everything goes well after), then go in and uninstall the graphics driver, restart, reinstall the graphics driver and reboot again, and then reinstall the KB2919355 update, the problem recurs. I also tried to download and to install the new update of firmware for my particular DESIRE machine which was released a few days ago, but which has not helped either.

  I'm really stuck. I looked up and down, and I scoured Internet for anything that might help. I need to update KB2919355 be installed because without it, I can't book my free upgrade of Windows 10. This laptop is about 2 years and a half old now, so it fulfills all the prerequisites for Windows 10.

  Please do not suggest that I do a Refresh of the system or a system reset, as I have no way to back up my programs, that which some I would not be able to reinstall because I have more drives for some of my programs. Also, I can lose to save him for some of my games.

  When people ask me "What's up?", I always say 'the CAP '.

  So that seems to have solved the problem that is described in this post here. I followed the suggestion, which was to uninstall the driver, SPDT DuplexSecure (which has something to do with the SCSI devices, I'm not quite sure) using the SPDTinst (download here) and now it seems that Windows has started without crashing after installing the update KB2919355. I'll check my Windows Update history and see if it is there.

  Low and behold, a year to be really behind value is ultimately more. I have successfully obtained the update of KB2919355 works on my computer.

• computer does not start after the installation of updates

  Just click on the button "installs the update and the computer shuts down."  When the computer turns off automatically, I pushed the power button and now it is frozen the computer in start mode.  What should I do now?  Can I power off and try again (or which will mess up the configuration of the update that he just installed.

  Note: There are 21 updates installed last night without problem; then 1 update again (that set up correctly when I restarted this morning).  After a successful this morning launch, I noticed there was an another update to install, which is what made me at this point.

  Single computer at home (I use my work computer to submit this application).

  Wait awhile and see if, during the initialization of the problem to be solved or not. It is NOT a good idea to unplug the laptop.

  If this does not work, then try to press F8 and choose last known good configration, but you may need to reinstall the update again.

• Reviews of Ubuntu does not start after the installation of updates

  I have a Windows 10 host and a guest Office Ubuntu 15.10. Ubuntu installs and runs fine until I have install updates, and then it gets so far through the boot sequence, but blocks trying to start the GUI.

  What should I do?

  Hello

  can confirm: after installing the last invited Ubuntu patches of the slaughtered 3.16.0-62 core during startup.

  Latest posts is: failed to start the vmware services.

  logfile VMware stops at the loading HGFS subsystem.

  To access the guest computer resolution: Boot with advanced options (hold SHIFT to start, until the menu loader grub is shown). Now select boot option (!) lower than 3.16.0 - 62.

  With 3.16.0 - 60, the guest operating system will start normally. Reinstallation or reconfiguration of the vmware tools don't fix this behavior. If something seems broken with kernel 3.16.0 - 62

  Any solution with core 3.16.0 - 62?

  Best wishes

• System does not start after the installation of update (10thFeb10)

  Updates to auto (windows Update) using.  Downloaded automatically update yesterday (10thFeb10) and when I shut my computer down it started to install them - as usuall.  However start my computer than this 11thFeb10 am and he began to run through regestry files when starting up.  Then it is impossible to load windows.  Just went to a blank screen.  Rebooted several times and were able to start it in safe mode.  Tried system restore but the same thing happens.  Obviously there was something to this update that 'changed' my computer and I'm not happy about it!  Also thought that there could be new updates (perhaps to fix the last update) but I can not even Windows Update to open it.  Tried online and he tells me that I have never downloaded updates and that none are available.

  I use Windows Vista Ultimate x 86.  I hope someone can help me!

  Got a response from Ms.  Good all who have this problem - you have an ATI Radeon graphics card?  Driver is causing the conflict.  Uninstall all the stuff ATI goes on ATI web site and install the download of 'single driver '.  Reboot and then you can download and install other fancy programs that come with your graphics card.

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

  Original title: xp does not start after the installation of avira

  I have a HP Slimline s7410
  XP Home Edition SP3
  I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
  I have a cd/dvd drive of work.
  I don't have an XP bootable installation CD

  My system worked well until: I installed the free version of Avira

  Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
  I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

  Here's what my BSOD looks like:

  Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

  Any help is greatly appreciated! :)

  My first suggestion is to do a system restore at this time point.

  second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

  third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

  Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

  so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

  fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

• Z600: computer does not start after the installation of the 5 TB SATA drive

  My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

  Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

• computer does not start after the installation of vista updates.

  computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

  Hello

  Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

  Hope that information was useful

• HP elitebook 2540p does not start after the successful bios update

  Hello people,

  I need your help.

  my hp elitebook 2540p with 2.5 "hhd does not start after a successful bios f.03 to f.24 upgrade done through windows 7.

  When I turn it on the blue light of wifi and power is on but nothing happen.

  I tried to remove the chip from the bios, cmos, hdd, ram, wifi battery... all, but nothing doesn't happen.

  I also tried to start it with the victory + b procedure and win + procedure four arrows so without USB key the caps lock flashing indefinitely but nothing happens, only the fan works quickly with a blue light

  with the USB the system restarts itself every two seconds and I have to remove the USB key.

  I do not know how...

  Thanks for any help.

  Luigi

  all very well now. I used the f.20 rom based on the internet and everything works again.

• Windows 7 32 bit does not start after the installation of the need for assistance

  I have an iMac 21.5 inches (mid-2011) with 8 GB Ram, 2 TB SSHD, new HL-DT-ST DVD - RW GA32N and tried to install windows 7 (32 bit) on using Boot Camp Assistant.

  I already downloaded and copied software 4.0.4033.zip Boot Camp here-> https://support.apple.com/kb/DL1630?locale=en_US for my 16 GB Pen Drive MS-DOS (FAT32)

  The installation was successful, and windows 7 loads just fine 1st time, I created UserID and password, settings etc... using the apple keyboard then installed the drivers from apple on this issue of my 16 GB USB key. Seems my Magic Mouse works but my keyboard is not detected

  Then I tried to restart so the changes would come into force, and since then my Windows will not start or run Windows 7

  Now if I start my iMac hold down the Option key, I get Macintosh HDD, windows, recovery 10.11.4 and DVD. If I select Windows or Windows DVD it starts Booting then black screen followed by this Message on the screen «Press a key to boot from the CD or DVD...» »

  If I press any button it starts booting from DVD and gives me the option to install Windows and if I do not press a button some then nothing happens

  Windows does not start a BootCamp HDD and I'm left with no option but to press on the button / stop to stop iMac.

  Fortunately my El Capitan works well, but my Windows will not start. I tried 2 times install windows 7 32 Bit on my BootCamp HDD.

  So any help, I do not understand what am I'm doing wrong, I would be really grateful if someone who knew bootcamp can guide me so that I can run Windows OSX on my iMac.

  Thanks in advance.

  Remove the DVD, boot in OSX and after the release of the following Terminal commands?

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  The "sudo" commands will prompt to enter your password, and there do not appear to come back. You can also see caution against improper use 'sudo' and the potential loss of data due to an "abuse" of the order.

• H8 - 1280t - QC461AV #ABA: desktop HP - computer does not start after the installation (Windows 10) video card

  So, I just bought a new video card an XFX R9-390 and a new HX1200i POWER supply corsair (overkill ik ) that I put on a card mother IPIWB-PB for my 3 years old HP PC, and the new stupid video card is not working. the PC just does not start, I see is a black screen. My monitor is an HP 2311gt and I can't use my computer with the old video card no probs, BUT whenever I have to install the new card does not detect my monitor just and I only see a blank screen. I HAVE NO IDEA HOW I'M DOING. Help, please

  PS. I have RMA the new power supply and the video card and they got to check and send back to me, so I know that the two pieces of equipment are working very well AND of course I am currently using my PC with the old video card

  Wiraqocha, here is the link to start safe for HPs with Win 10 and instructions to enter the BIOS. It may be useful:

  HP PC - secure boot (Windows 10)

• Satellite A300-15 a does not start after the installation of the alcohol program

  Hello...

  Satellite A300-15 has, I bought yesterday and after completing the installation of Vista, I tried to install "Alcohol" but my judgment of the laptop and now I'm not able to boot up the laptop.
  It does not start in any mode.

  I forgot to make recovery disks. I think that alcohol is not compatible with Vista. Error I get is below.

  Can someone tell me the solution?
  Please help urgent

  "A problem has been detected and Windows has shut down to prevent damage to your computer.
  If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: blah blah... "

  Looks like a problem familiar to me, as I had the same one with the Daemon tools. After installing these tools, I couldn't start my Windows XP. I guess that it somehow mixed upwards of some drivers or registry entries, but not sure about that.

  OK, you can try to uninstall tool first start Vista in safe mode (press F8 before Windows starts upward).
  You should then be able to enter in Vista without problem.