Windows 7 not able to remember my settings of the mouse when I alternate mouse

Similar Questions

• Not able to save keyboard settings after reboot / logoff

  Original title: "Appy" of change is not saved

  1. I have an ACER Aspire One. Every time when I changed the keyboard settings and "Applied", it only works for the duration of the session. If I disconnected and then reconnected, the changes will be gone. I have loggon as administrator. Any help will be appreciated.

  Hello

  1 were you able to save keyboard settings in the past? If Yes, you did it all change hardware or software before the show?

  2. What is the exact model of your computer number?

  Method 1:

  See the following Articles from Microsoft:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  http://Windows.Microsoft.com/en-us/Windows7/automatically-get-recommended-drivers-and-updates-for-your-hardware

  Method 2:

  Uninstall keyboard drivers.  Download the drivers for keyboard from the manufacturer's website and install it.

  Method 3:

  Please start your system in safe mode and check if the settings remain unchanged, it.

  To start your computer in safe mode through the article mentioned below

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

• Windows is not able to load the selected for the following reason of backup set

  Hello;
   
  I did run a daily backup to a computer in a network with windows backup and Restore Center. the hard drive crashed on this computer and we had to install another. When I try and use advanced restore / backup made on a different computer, I can navigate to the backup on the network computer folder but when I select the folder and click Next it gives me an error:
   
  I get: Windows is not able to load the backup game selected for the following reason:

  There is a problem with the backup catalog... 0x810000E5... restore from a different place...

  Just to add additional information; The computer with the replaced hard drive running Vista family premium, the path to the backup file is \\HPDESKTOP\Public\Backup\Bobruncer-pc\.

  There is another folder under Bobruncer-pc called Bobruncer-pc and all the backup files. I restore from the correct location? Also, the backup folder is 226 concerts but the backups were made from a hard drive of 80 GB... should I worry about this too?

  Thank you

  Dave

  Hi Colt4t5,

  Just to clarify, perform you a complete PC Backup or backup and restore?

  When you do return, and restore, it can be saved as a .zip file in the backup folder. You can decompress the file and retrieve the required files.

  Restore files from a backup
  http://Windows.Microsoft.com/en-us/Windows-Vista/restore-files-from-a-backup

  Back up and restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions

  I hope this helps.

  Bindu S - Microsoft Support

  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• I get the message when you set up a new user "a temporary user profile is loaded because Windows was not able to connect you with your local profile."

  Dear all,

  I have a Windows PC in my office. Because of some configuration issue, I deleted the domain user and tried to connect to the system with the same user credentials. It identify you with the credentials of the user, but I get a message saying: "a temporary user profile is loaded because Windows was not able to connect you with your local profile."
  This system is joined to the domain and the profile is an Active Directory user.
  Here are the details of the event ID:

  Details Product: Windows operating system Event ID: 1515 Source: Userenv Version: 5.2 Symbolic name: EVENT_PROFILE_DIR_BACKEDUP Message: Windows has backed up this user's profile. Windows will automatically try to use the saved profile the next time the user connects. Explanation A temporary user profile is loaded because Windows was unable to connect with your local profile. A possible cause of this is if your local profile has been corrupted or that you no longer have the correct privileges for profile records. Note: Any changes made to the temporary profile is lost once you disconnect. User action Search the profiles additional events in the event log for more information on the reason why this happened or contact the system administrator for further assistance.

  There is currently no article for this specific error Microsoft Knowledge Base or an event message. For more information on other technical support options, you can use to find answers online, see http://support.microsoft.com/default.aspx.

  Please, help me to create the same user profile in the system with formatting system.

  Hello

  I suggest you to refer to this link and check if it helps:

  http://support.Microsoft.com/kb/947215

  It will be useful.

• Windows computer not able to find the software adobe reader XI? I have tried repairing, did not

  Windows computer not able to find the software adobe reader XI? I have tried repairing, did not

  Hi Kenneth,

  Please try & download Adobe Reader using this link Adobe - Adobe Acrobat Reader DC Distribution.

  Let me know if the problem persists.

  Kind regards

  Nicos

• Internet connection issues "Limited or no connectivity." and "windows could not find a certificate to log on the network.

  I'm so unable to connect to the internet?

  Hello.

  I'm so unable to connect to the internet.

  Since I've renamed our WiFi network and add a WEP key, I have problems with wireless connection on my
  Windows XP computer desktop, which is a Dell Dimension 4700.

  The questions that I get connection are...

  "windows could not find a certificate to log on the network.

  "Limited or no connectivity."

  I did all the solutions I could try to fix the connection problem!

  1. once I received the message "limited or no connectivity", I click with the right button on the connection and click on repair. It is not always connect for me and I got the "limited or no connectivity message.»

  2. then, I disabled the network connection and then enabled. That no longer works.

  3. I tried to withdraw from the ordered list of connections, and it still doesn't work.

  4. I checked the driver manager, and initially the Ethernet driver was outdated and missing of its pilot. He had a yellow question mark with a black sign and yellow with an exclamation mark inside.

  5. I used DriverZone, downloaded the driver, installed and rebooted the computer after the installation of the it. Apparently, it worked. But I could not always connect.

  6 I have ensured that I entered the correct WEP key, and then adjust the settings correctly. I did it like 10 times in a row and would not always connect.

  7. I tried to go to the command prompt and typed in IP Config/All and that's what I mean.

  Windows IP configuration
  Node type: unknown
  Active IP routing: no
  WINS proxy enabled: no
  ETHERNET connection to the Local network card
  State of the media: Media disconnected
  Description: Intel PRO/100 VE Network Connection
  Ethernet card 2 wireless network connection:
  Suffix the connection-specific DNS: (EMPTY)

  8. after that, I typed the command: ipconfig/release
  and then I got this error...

  No operations can be performed on the connection to the local network, although it has its media disconnected.

  9. after that, I tried Googling for some solutions, and the solutions I found were not any use.
  A solution was

  10. opening of Services...
  Start | Run | Type: services.msc | Click OK |
  Scroll down to and double-click Client DNS | Set to automatic on startup
  type |
  Click apply | Click the Start button | When it starts, click OK
  Do the same for the DHCP Client.
  Do the same for the remote procedure call (RPC).

  and it still doesn't work.

  11. when I look in the menu network connections, I see my connection with a lock on the side, with a red X under the lock and key. In the description, I see not connected, protected by a firewall. How could I remove the internet connection firewall? I disabled the firewall and that did not work.

  12. I tried to uninstall and reinstall the network card and who does not work either.

  It is not the network itself that is the problem.  It is not the modem or the cable. There are no disconnected son or something like that. We have other computers in the House and the internet works fine on other computers. As I said, since I renamed our WiFi network and added a WEP password, I had problems with connecting to my Windows XP computer.

  My computer has updates that must be installed as well. Updates would fix the problem? I just need to have internet.

  What should I do? Thank you for your time.

  Sincerely,

  Justin

  Have you tried to set the value of the link speed/duplex mode? I had the same problem you describe. Your card is only capable of 10/100 communication.

• someone is using my email address to send emais. I tried to reset my password but I am not able to. He says that the answer to my secret question does not.

  someone is using my email address to send emais. I tried to reset my password but I am not able to. He says that the answer to my secret question does not. I know I'm getting the correct ansewer. Help, please.

  Hi, Catherine.

  You'd better post in the Windows Live Solution Center-Hotmail like that is dedicated to Windows Live Hotmail.

  If you have not implemented alternative methods to check your Hotmail credentials, I suggest do it after your account is returned.  For more information, see Security Hotmail to protect and recover your account .

  Good luck!

• Unable to connect on the internet on another computer - "Windows could not find a certificate to connect to the network (named).

  When I try to connect to internet on my other computer I get a message saying "Windows could not find a certificate to connect to the network (name)". It's only since I've had a second computer as it does on my old computer which is

  a laptop HP Pressario with Windows XP Home Edition. Someone told me to go to authentication in wireless networks, but can highlight something here as everything is gray.

  Hello

  · What type of encryption do you use on the router?

  · You have the latest drivers for your wireless network card?

  Make sure the authentication IEEE 802. 1 x wireless card is disabled, and check if that helps.

  a. Click Start, then select run.

  b. term ncpa.cpl type dialog box and then click OK.

  c. right click on wireless network connection icon and select Properties.

  d. click the wireless network tab.

  e. click on the properties button next to remove it.

  f. click on the Authentication tab, and then clear the authentication 802. 1 x IEEE select this network check box.

  g. click OK to update the settings.

• Please help, my other computer shows an error message: "Windows did not start because of an error in the software: load needed DLLs for kernel.

  Please help, my other computer shows an error message: "Windows did not start because of an error in the software: load needed DLLs for kernel.

  Hello

  ·          What is the number and the model of the computer?

  ·          What is the service pack installed?

  ·          The meadow of operating system has been installed on the computer?

  ·          Do you remember any changes made on the computer before the show?

  Try the steps listed in the link below: how to fix a computer that does not start: http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx

  You can also check: Error Message: Windows could not start because of the mistake in... : http://support.microsoft.com/kb/326671

• Dual Boot with windows XP Pro with 2 HARD drive, error on secondary windows install: "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check boot path and disk hardware... »

  Hi, I recently bought a new Hitachi 1 TB internal hard drive. I wanted to do a clean install on the new drive (d), be able to dual boot my computer and leave my old 300 GB disk (C :) as the primary windows installation. After physically installing the new HARD drive, I noticed that "new hardware found" and the the brand name flashed in the bottom right corner. I thought I'd see the new hard drive in my computer, but I did not. I initialized the new HARD drive with the computer management window (right click on my computer - manage) and I also formatted in NTFS (I had to change my printer hard drive letter to assign the new HARD drive with the letter D, but I've made other changes after this step). Now, I could see and use in my main windows on the C: installation. I then installed a windows new copy XP pro with the installation CD I got for my C: but on the D: (Note: I have a Dell computer (and the Dell reinstallation CD) and my current version of windows has SP3 while the installation CD is only SP2) (I also reformatted my HARD drive during the installation of windows to NTFS)

  Now when I try to start on installing the new on my D: I get "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check startup disk and hardware access path. "and another line saying to refer to manuals HARD drive and windows.

  My Boot.ini file at this time was:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (0) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I looked towards the top of this help page, but for now I'm unlucky:

  http://support.Microsoft.com/kb/314477

  (The next steps I took by throwing from the Windows CD and go into the repair console)

  I tried to use the bootcfg /rebuild but the line to boot.ini for my secondary HARD drive still does not work.

  He gave me something like:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (1) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I also tried to change the signature() to multi (0), but it did not work. (or try almost all possible permutations of disk() and rdisk() partition() 0 to 2).

  I also tried to use expand F(dvd-drive):\i386\ntkrnlmp(I_have_a_duo-core).ex_ D:\windows\system32\ntoskrnl.exe and a few other combinations, but I when I login as D:\windows simply, it fails to extend with a message like "could not develop" or C:\windows I get "restricted access".

  I have not yet tried CHKDSK/r, but since I did a clean install on a newly formatted drive... I don't think it would work.

  I've also marked the partition on the D: as active (in computer management), but it did not help me.

  I've done a first installation of windows repair, strangely, I couldn't fix this one... Still does not work...

  My default windows installation yet works very well & I see that windows has been installed on the D: but I'm ideas from how to operate the dual-boot, can someone throw me a BONE on what to do?

  Maybe try to do something with the Boot Manager (whatever it is?) Create a new partition and use it as a boot manager? I don't really want to do this, because if I made a mistake I will be unable to use my computer and dual boot should work without going through all this trouble... But I found this page: http://technet.microsoft.com/fr-fr/library/ee829686%28WS.10%29.aspx

  Could a clean install two HDD help? I hope I won't have to do...

  Someone has an idea?

  PS: I'm not such an advanced user so I need a solution step by step, thanks!

  Edit: I also noted that I can't see my new HARD drive in my BIOS... weird... SATA-0 is my old drive HARD 1 and 2 are my dvd 3-5 readers are 'off' and it doesn't seem to be anything that it is plugged in. I also have 4 bays for internal HARD disks. Now, 2 are busy.

  Edit2: I looked inside my case and enabled the good Sata in the Bios after a reboot it detected the drive correctly. Dual boot doesn't always work well... The fact that it was disable in the BIOS while I was installing the new HARD drive could change anything? Hmm...

  In case I wasn't clear enough: I had a windows XP Pro installed on my C:, bought a new hard drive and installed the same copy of windows on it (d). I think that should allow me to double boot between the two installs different. Even if for some reason I can't boot from one on my D:. Andrew, I do not understand why you so far physically disconnect the other drive, the point of the whole operation is to build a boot.ini file so that the BIOS knows that it y facilities 2 windows and you allow to choose (and not have conflicting problems between the 2 systems), someone correct me if I'm wrong? "Expand" the part of my first post made reference to one of the solutions provided by Microsoft in the first link that I have included in my previous post (but I can't seem to work).

  In addition, it is the procedure that I followed: http://www.ehow.com/how_5950826_boot-two-different-hard-drives.html

  (except I've had the first installation already done).

  Andrew "also, once a new hd is plugged on the pc & running, most of the BIOS will place (them) as 1st priority hd, set the BIOS to do this", you mean that by installing separately from windows on each unit when the other is not plugged in, I could choose what disk to start from defining their priority in the BIOS once they are all plugged back? It's too tedious (as I intend to move frequently between the 2 installs) and requires a computer to other users of the lack of computer knowledge. Unfortunately, it is not a viable option.

  EDIT: I DID IT! Hmmm... Well, I double checked in the recovery console, the path of the new HARD drive with the arc command Scan. Tried to start again with the MULTI (0) in my boot.ini and it worked... I also had my windows install CD in. Maybe that is why I could not start, windows needs the CD to complete the installation? Weird, I don't know what I did to the difficulty it... but hey, it works! Thanks for your ideas guys!

• Not able to install updates to get the message: 'updates were not able to configure correctly, returning from changes'...

  Original title: I have Vista with Service Pack 2, but were unable to come down and configure updates since 07/12/11. Need help, thank you.

  Do not get the error codes. Just when I reboot, I get the message "updates were not able to configure correctly, returning from the changes".

  Hello

   
  You are able to start in safe mode, then you can perform the clean boot in safe mode and then try to boot into normal mode.
  Put your boot system helps determine if third-party applications or startup items are causing the problem.
   
  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.
  If you are able to boot to the desktop after you perform a clean boot Windows check updates history of inforamtion on the updates failed.
  Reference:
   
  http://Windows.Microsoft.com/en-us/Windows-Vista/see-which-Windows-updates-are-installed
   
   
   

• I use Windows 7 on a computer to which a printer is connected directly by a USB cable. I am able to print, but cannot find the printer when I run control/devices and printers Control Panel

  I use Windows 7 on a computer to which a printer is connected directly by a USB cable.  I am able to print, but cannot find the printer when I run control/devices and printers Control Panel. In fact, no devices appear at all.

  Can someone help me with this?

  Thank you.

  See http://www.winhelponline.com/blog/fix-devices-and-printers-completely-empty-windows-7/

  If this does not help, there is a very long thread here, which may include other suggestions--> http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/devices-and-printers-dialog-box-empty/353707a4-bcb0-4334-98bc-aab84747fecd?page=1

• Windows could not find a certificate to log on the network

  So I try to connect to the network that appears, and then trying to connect but it with "Windows could not find a certificate to log on the network. Now, I tried unchecking security in the properties box and also to uncheck it to 'use windows to configure my wireless network.

  NONE OF THESE WORK FOR ME!
  Also attempted to fix the network, but he says that "windows could not finish repairing the problem because it is impossible to perform the following action: connect to the wireless network '"
  I am currently under SP2, but in the process of installing SP3.
  Help!

  This error usually occurs because you have specified a connection protocol 802. 1 x.  You must configure your properties to uncheck this box.  See the following article:

  "Windows could not find a certificate to log on the network.

  <>http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-Networking/window-was-unable-to-finad-a-certificate-to-log/f68d2ea6-51c4-4B86-a5de-da4d06afb50a >

  HTH,
  JW

• error message: "windows could not find a certificate to connect to the network.

  My NetGear wireless icon shows this error message "windows could not find a certificate to connect to the network.

  Hello

  Did you change your computer before this problem?

  You can follow the procedure in the article.

  Unable to connect to the network: Validation and certificate in Windows XP and Vista errors

  http://KB.NETGEAR.com/app/answers/detail/A_ID/7334/~/unable-to-connect-to-network%3A-validation-and-certificate-errors-in-Windows-XP

  Alternatively, you can contact Netgear support to improve assistance in this regard.

  Welcome to the NETGEAR support

  http://support.NETGEAR.com/

• NO wireless network connection - message "Windows could not find a certificate to connect to the network Shaida. How to fix this problem?

  I had just restored my Thinkpad T60 the default setting. Reformatted and reinstalled Windows XP, but I am unable to connect to the wireless network connection - message "Windows could not find a certificate to connect to the network Shaida.

  Shaida is my wireless modem.

  How to fix this problem?

  Before the resumption of connection Internet worked normally.

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://support.Microsoft.com/kb/870702

  It will be useful.