WINDOWS CANNOT FIND ANY ADDITIONAL NETWORK (DIAL-UP AND VPN) OTHER THAN THE WIRELESS NETWORK

Similar Questions

• Windows cannot find any additional network?

  I am currently using my laptop that can connect to my home network but my PC can't. My PC can't find no additional network. It says it is connected to the network called 'Network', but I can't use my internetor all programs using the internet. It says "windows cannot find any additional network." I clicked on "Diagnose why windows cannot find any additional network", it told me to update my drivers and my drivers he's was updated. Can someone help me?

  Hello

  You can check the link below and try the advice given and check if that helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/Windows-cannot-find-any-additional-networks-an/ca9f086b-42A5-46E5-b894-92c009f8eba8

  Hope that information was useful

• Windows cannot find any additional network / an unexpected error has occurred

  I got this new PC Windows Vista Home Edition x 64 SP2 and I need to connect it to the network wireless in my house because that the router Netgear DG834GT wireless broadband is not very conveniently placed for wired connectivity. I have a Netgear WG111T USB wireless adapter which works fine on my other PC / laptop (XP & Vista, both 32-bit), but I can't make it work on my Vista x 64 PC.

  I have installed the version of the driver 2.1.0.26 x 64-compatible for the WG111T and the device works correctly, according to Device Manager.

  When I try to 'connect', I get 'Windows cannot find any additional network . " While the other PC at home can pick up 3 wireless networks.

  Go until the network & sharing Center, then manage the networks without wire, then Add, then manually create a network profile, I get "unexpected error ."

  I spoke to Netgear who insist the player WG111T is compatible with the x 64 visits.

  I talked to my PC provider who suggested to try the adapter on another PC Vista x 64 to see if it works there. Problem is, I don't know anyone else with a Vista x 64 PC.

  I would be extremely grateful if someone can help me before on this one. Thanks in advance for all advice.

  See you soon,.

  Arty-W

  It seems that the problem was caused by ZoneAlarm Internet Security Suite hinder and prevent the correct installation of the Netgear wireless driver. My problem has been cured by following the advice of daouda wire - see http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/58716eca-80cb-4555-a1f4-bd4e5350aeb4

• Windows cannot find any networks

  Hi all

  My dsl network connection is not discovered by vista suddenly I have tried all possible means, but to no avail any help would be greatly appreciated!

  the error message says "windows cannot find any network."

  its a DSL connected via a LAN connection

  I think I found the culprit, it turns out be a updated windows defender definition... ive stopped using my network connections now run fine LOL

• Windows cannot find any networks, but Ubuntu can! (X 32 Vista Home Premium)

  I recently replaced a faulty laptop computer mother board with an identical model (only difference is a newer version of the BIOS). After restarting Windows (Vista Home Premium 32 bit) I can't find the networks wireless where I can see usually eight networks at least an unsecured connection, but now I get nothing.

  I replaced the wireless card Atheros with an Intel Pro 3945ABG driver and installed the latest version and that I still get the same error "Windows cannot find any networks", I can get access to the internet via an Ethernet cable but I am unable to connect wirelessly. If I try to manually configure the wireless connection, I get "unexpected error occurred".

  I started the system from a CD of Ubuntu to check that it was not a hardware problem. Wireless card perfectly, sees all the networks, connects and works very well.

  It seems that something inside Vista has failed since even change the wireless adapter for a different manufacturer and the results of the modeling in the same error, pointers?

  Kind regards

  Jason.

  SOLVED

  It turns out that Kaspersky Internet Security is at fault and he was very happy to work via ethernet it had mutilated all WLAN connections.

  Removal of Kaspersky and all of a sudden all the wireless networks have re-emerged.

  Kind regards
  Jason.

• error message "windows cannot find any network."

  When I try to connect to my wireless network, I get an error that says "windows cannot find any network". Already called my internet provider and has been sent back to microsoft. I have a netbook at home and he search for connection to the internet, but my desktop running Windows Vista Home prem is this error message. I use microsoft MN500 as my router.

  Hello

  1 are there any changes or updates made on the computer?

  2. were you able to connect to the network before?

  Method 1:

  I suggest you to return the item and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  I suggest you to reset the TCP/IP Protocol and check if it helps.

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357

  Method 3:

  See the link and check if it helps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/kb/928233/en-us

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up the registry, (http://support.microsoft.com/kb/322756/) see link:

  Back up the registry

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

• Windows cannot find any neworks with Wi - Fi

  I have a Toshiba laptop that connects to the internet via a Belkin N router.

  During an internet session, the laptop can lose connection and if I try to connect to a network I get the error message "Windows cannot find any network."

  Nothing has been changed during the session.

  Laptop computer shutdown and restart will allow the laptop to auto automatically reconnect to the preferred network.

  My impression is that it is a software problem.

  Hi kaspercat,

  Rather than restart you tried the option "diagnose and repair"? Right click on the internet icon (two monitors flashing) in the notification area and in the menu drop-down, select diagnose and repair. This usually works fine for me if the laptop on my network loses connection.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: Web: http://www.winuser.co.uk ; Web: http://xphelpandsupport.mvps.org ; Web: http://vistasupport.mvps.org ; Web: http://www.silversurfer-guide.com

• Windows cannot find any network (unable to connect to the internet!)

  I use Vista on my laptop... All of sudden my connection to laptops is down... and when I searched for my wireless connections... I get a message indicating that Windows cannot find all the networks.

  I can find networks and connect to our wireless through other cell phones in the House.

  I am, however, not possible to connect to the same if internet I connect the cable from the laptop to the router.

  I also tried to restore the system to 3 days before the problem happened, however, I had no chance to fix the problem!

  Please... anyone know how I can fix this problem?

  Any help will be very appreciated!

  SHWC9507

  Hello

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Windows cannot find filename.extention in "search programs and files".

  Hello all, there is a program called "Recuva" by Piriform there (it is a data recovery program). When I try to find the program (Recuva64.exe) on "search programs and files", I see "recuva", (the r without ceiling). When I click on that, a message box appears, saying "Windows cannot find '' Recuva64.exe' '. Make sure you typed the name correctly and try again. »

  Its running Windows 7 Home Premium 64-bit.
  If someone could help me solve this problem, I would be very happy. Thank you.
  PS: Same problems occur with Defraggler of Piriform CCleaner too.

  I'm not sure that I follow the problem then, sorry?

  It is just this program that fails, or all searches fail?

  If you click on "Recuva64.exe" it runs?

  Have you tried to remove and reinstall it?

  NOTE: later found this on a google - http://www.pcerrorfixtip.com/Recuva64.exe-318841.html I don't know on this site or one of its suggestions, I just found on google. But it does not mention "Windows cannot find C:\Windows\Recuva64.exe make sure you typed the name correctly and try again ' in the ' Recuva64.exe error messages:" section. Not sure if this is useful. AV check anything you download (as appropriate) from the site that I don't know anything about them, just a response from google. It will be useful.

  
  

  I hope that someone else may have an idea and help.
  

  
  

  
  

• «Windows cannot find setup.bath...» "Help, please!

  When windows starts, there is an error message «windows cannot find setup.bath...» "and when I click ok my pc restart. What should I do? (Sorry for the bad English)

  To access the system recovery environment in Windows 7, simply start your PC, just before the system loads the Windows operating system. Press the [F8] key function 8 on your keyboard which will launch the menu Advanced Boot Options. You will see a new option "Repair your computer", select this option and press 'Enter' on your keyboard.

• Windows Vista cannot find any networks after reformat

  Windows Vista cannot find any networks after reformatting. Help!

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

  The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.

  See you soon.

  Mick Murphy - Microsoft partner

• When I perform a net view on, I get the error system error 51 next. Windows cannot find the network path.

  Net 51 with a view system error

  I have two boxes of Windows XP that I login as administrator account. I was able to synchronize files, map network drives and can do a tracert to reach one of them.

  However, when I perform a net view on, I get the following error

  51 system error has occurred.

  Windows cannot find the network path. Make sure the network path is correct and the destination computer is not busy or turned off the coast. If Windows still can't find the network path, contact your network administrator.

  How to make this command work?

  Hello

  ·         Your computer is on a domain network?

  Follow the steps in troubleshooting this article and check if that helps:

  You cannot access shared files and folders or browse computers in the workgroup with Windows XP

  http://support.Microsoft.com/kb/318030

  See also this article that resembles the same error.

  Error when you try to access shared resources on a computer that is running Windows 2000 or Windows Server 2003: "53 system error has occurred" or "51 system error has occurred."

  http://support.Microsoft.com/kb/259878

• Windows cannot find a driver for HP LaserJet 1022 on the network. To locate one manually, click on OK.

  Computer (win xp 32-bit) A located 1020 printer with sharing

  Computer B (win 7 64bits) successful connect through A computer printer share

  Computer C (win 7 64 bit)

  Computer D (win 7 64 bit)

  D C & computer appeared this message: -.

  Windows cannot find a driver for HP LaserJet 1022 on the network. To locate one manually, click on OK.

  When I click OK, I get an error message:

  Required file: INF for HP LaserJet 1022 printer driver
  The file '. INF' (unknown) is needed.
  Type the path where the file is located, and then click OK.

  On the Win 7 computer...

  Devices and printers
  Add a printer
  Add a local printer
  Select create a new port:
  Select Local Port for the port Type:
  Enter the name of the network to the XP computer that is. \\XPcomputername\LJprinterid
  Install the LaserJet 1020 driver when prompted

• WILL ESX 3.5 works on my laptop that has the NIC Intel(r) PRO/1000 pl... (I'm getting "cannot find any network device error taken supported")

  Hi all

  For the purpose of learning, I try to install ESX3.5 on my "vmware workstation 5.0 ' on my laptop. Installation stops @ "unable to find any supproted network devices. I suspect that this (Intel (r) PRO/1000 PL) is not supported, can anyone confirm this?

  In the compatibility list, I can see in favor: Intel(r) PRO/1000 PT...? , mean PL is not supported?

  Thank you

  Ashwin

  You say that you are not able to change the *.vmx file? You should not have the virtual machine running, then edit the vmx file. You need to REPLACE the line indicating the type of ethernet0 (from there, all that is initially at 'e1000'. Then, save the vmx file and exit the texteditor.

  Starting the virtual machine with the mounted CD of ESX.

  Can tell you how, you get an error (and what is the exact error).

• Windows cannot find C:\Docume~1\owner\Locals~1\Temp\dwm.exe

  I get the following error at startup: Windows cannot find C:\Docume~1\owner\Locals~1\Temp\dwm.exe

  Once I click ok, I get the same error message, but it says it could not load or run it from the registry.

  In addition, I can not get on the internet on my PC. I can access the internet fine on my laptop through y network.

  I read how to solve the error message, but I can't get on the internet to access programs. Suggestions? I'm so frustrated!

  Thanks in advance!  :)

  Steve Winograd's right - no executables are normally launched from the Temp folder where you specify unless the malware put them there.

  Your system is currently or has been infected and perhaps your detection/removal software clean the folder Temp of the suspicious content but this process does not always boot entry that points to the location/suspicious file, so that each reboot (or login), he wants to run it.

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..

  It is easy to get rid of the error message by doing something like disable the startup item in msconfig (if you can still find), but I suggest you fix the problem and difficulty not only the symptom of the problem simply remove the startup message.

  I would recommend also you start to search in the register, unless you have a backup because there is no 'Cancel' or 'quit without saving changes' option in regedit.  If you make a mistake, that's all.
  These ideas relieve 'rapid' and sometimes risky of the symptom, but may not actually solve the problem.  Also, I'd be suspicious of ideas that begin with the words "try."  You don't need to try things, you need to fix things.
  Here are the detailed instructions that protect you and solve your problem in the 'right' way.
  Describe your current antivirus and software anti malware situation: McAfee, Norton, Spybot, AVG, Avira
  !, Defender, ZoneAlarm, PC Tools, MSE, Comodo, etc..
  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.
  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry. There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can use Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner.  Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information.  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove
  .  If you are not sure what it is, you can simply disable, restart and if the problem is resolved and then remove the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that you had or have an infection, followed with this:
  Perform scans for malware, and then fix any problems:
  Download, install, update and do a full scan with these free malware detection programs:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.

  Do, or do not. There is no test.

  I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!