Windows could not complete the installation. To install Windows...

on this computer, run the Setup again.

HI - trying to proceed with the restoration of the Vista operating system using recovery discs sent by HP.  It runs the entire sequence and uses two disks, installed all software, updates of fact and on what appears final reboot displays this message in a black screen. When you click ok, it will restart and run Setup again is not resolved. Am in a endless loop.

I see the office if I complete the runonce process in the Task Manager, but if I close the Windows Installer window, it goes in the reboot and the cycle starts over.

Please help someone!

This is the error message after running HP on HP pavilion dv6700 laptop system recovery disks. OS is Vista Home Premium. p/n KC415UA service tag dv6756us

I order usually Newegg.com but you can probably find one at any Best Buy store, Staples, etc. Newegg usually has the best prices. You need a hard drive 2.5 "sata mobile. The old hdd will have also an adapter plastic through the pins that you need to remove and place on the pins of the new hard drive.

Tags: Notebooks

Similar Questions

  • Windows could not complete the installation. to install windows on installation of HP DV6-7007TX, this restart of the 64-bit computer

    I buy a new HP Pavilion DV6-7007TX. I don't want the pre loaded Windows 7 Home Premium 64 bit that's why I decided to format it using Windows 7 Ultimate 64 bit, but after reboot before the Installtion "filling" to finish an Error Message is displayed "windows cannot complete the installation. to install windows on installation, this restart of the computer", I rebooted several times but the same error pops up

    Why not just do you do an Anytime Upgrade of Windows 7 Edition Home Premium to Windows 7 Ultimate?

    If the license for Windows 7 Ultimate, you have access to is a retail version update or complete, you can use the product key and the Express upgrade to Windows 7 Home Premium to Windows 7 Ultimate. First of all, check that the edition of Windows 7, you are upgrading is already enabled (if it isn't, you will encounter complications and that you might start all by performing a clean installation). Click Start, type Anytime Upgrade, click on the option enter a key, enter the key of Windows 7 Ultimate edition at the request, click Next, wait while checking the key, accept the license agreement, click on upgrade, wait while the software upgrades, (it may take 10 minutes or more depending on the if updates are required) your computer restarts automatically, after the reboot, Windows 7 will notify you updating the computer, the computer will restart once more automatically and will be completed the upgrade, a window will appear notifying the upgrade was successful and your computer is ready to use, click Close, you should be upgraded to Windows 7 Ultimate files the stored settings and programs.

  • Windows Vista - after the RESTORE partition HARD drive: WINDOWS COULD NOT COMPLETE the INSTALLATION. TO INSTALL WINDOWS ON THIS COMPUTER, RESTART THE INSTALLATION

    Hello

    I have WINDOWS VISTA and just tried to reinstall my laptop of restoration on a HARD disk partition.

    The restore went through, but then I got the error: WINDOWS COULD NOT COMPLETE the INSTALLATION. TO INSTALL WINDOWS ON THIS COMPUTER, RESTART THE INSTALLATION

    When I press 'OK' (which is the only option), it tries to start again, until I get the same error through the black screen.

    How can I get out of this loop please?

    Thank you.

    Lucie

    Hello

    For any problem with the help of the recovery Partition that has been copied to the hard disk by the computer manufacturer, you must contact them.

    This recovery process is the manufacturer, not Microsoft.

    ________________________________________________

    You never told us why you wanted to do a restore. If you had serious errors and the recovery process does not work, you will have hardware problems. BUT we're only guessing at this stage due to lack of information to help you.

    See you soon.

  • Windows could not complete the installation - Message in Vista 32

    Windows could not complete the installation. To install windows on this computer, run the Setup again.

    I get this message when I switch on my compaq CQ40 with Vista 32. From this screen, I can go into Manager tasks and go online, see the program files on the C: drive, change passwords, etc. Anything except support Vista. I just downloaded and installed SP2 via the Task Manager. Always stops after the Welcome screen. Another thing I never noticed before: during the boot and just after opening orb, the Welcome to Windows message lights up with the small circle of progress, then I hear a sound of gong just before startup fails. Curious. Any help out there?

    Hello

    This article explains how to troubleshoot problems when you install a service pack for Windows Vista or Windows Server 2008.

    http://support.Microsoft.com/kb/947366

    Use this forum link for all questions related to Windows Vista SP1, Windows Vista SP2 and Windows Server 2008 SP2 below.

    http://social.technet.Microsoft.com/forums/en/itprovistasp/threads

    or repost in the Windows Update forum link below

    http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all

  • Sysprep is not - Windows could not complete the installation

    Original title: Sysprep failed

    I started a sysprep on my windows7 pro computer restarts and says

    From Windows, it jumps to "Setup prepares your computer for first use.

    After 5 seconds an error occure

    / "Windows is unable to complete the installation. To install Windows on theis compuiter, re-run the installation. »

    I press Ok and it says installation continues after the reboot.

    and in this loop im stuck.

    Is it possible to do a new sysprep without getting the OS to start?

    Hello Simon,.

    Thanks for posting your question on the Microsoft community.

    We need more information about the issue so that we can help you better.

    Your computer is connected to a domain network?

    Thank you for details on the issue.

    Preparation system (Sysprep) tool prepares an installation of Windows for duplication, auditing, and customer delivery. Duplication, also called imaging, allows to capture a customized Windows image that you can reuse throughout the organization. Audit mode allows you to add additional device drivers or applications to a Windows installation. After you install additional drivers and applications, you can test the integrity of the Windows installation. Sysprep also allows to prepare an image to be delivered to a customer. When the customer boots Windows, Windows Welcome starts.

    You can check the suggestions of MarkBeacom responded on 28 June 2012 and Mark l. Ferguson responded on November 3, 2009.
    http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/Windows-could-not-complete-the-installation-to/bf09c3c5-298B-459F-AED5-4f431b8398f5

    I hope this information helps.

    Please let us know if you need more help.

    Thank you

  • Windows could not complete the installation.

    Hi, I use the windows 7 edition starter with ASUS Eee flare series.  This message appears when I do the system restore, "Windows could not complete the installation. To install windows on this computer, restart the installation.

    Hello

    Welcome to the Microsoft community.

    According to the description, it looks like you get the error, such as "Windows could not complete the installation" when you perform a system restore.

    However, we need more information about the issue to help you better.

    Please help me to answer these questions.

    Why you perform a restore of the system on the computer?

    Try this method and check:

    Method 1:

    Try to choose a different restore point and check.

    Method 2:

    Perform a startup repair

    Note: you can perform this step only if the mode of the Windows recovery environment is enabled on your computer by the manufacturer of the system (Acer). This mode allows you to use the recovery options.

    Click: Startup Repair

    Also check:

    What are the system recovery options in Windows 7?

    http://Windows.Microsoft.com/en-in/Windows7/what-are-the-system-recovery-options-in-Windows-7

    Hope this information helps. If you have any additional questions with Windows do not hesitate to answer and we will be happy to help.

  • hure Pro XI could not complete the installation process, even if the progress window said it was downloaded 100%. In the installation process it uninstalled my previous version of Acrobat, now I can't open the PDF files.

    Acrobat Pro XI could not complete the installation process, even if the progress window said it was downloaded 100%. In the installation process it uninstalled my previous version of Acrobat, now I can't open the PDF files.

    Hi RKrensel,

    Please let me know the version of the operating system installed on your computer?

    If you are on windows system, run this tool cleaner Download Adobe Reader and Acrobat tool - Adobe Labs & restart your system.

    Make sure that there are no Adobe process running in the background using the Task Manager.

    Then try to download & install Acrobat XI using this link Download Adobe Acrobat products. Standard, Pro | DC, XI, X & serialize using your Adobe ID

    Let me remind you that your subscription for one year has already expired on 4 September

    Kind regards

    Nicos

  • Red flyer 15.6 "15-f272wm: Windows could not complete the installation

    I just got my new laptop and when I turned it on, a window appears and says that Windows is unable to complete the installation. Install windows on this computer, run the Setup again. I rebooted several times and it's all the same result. Nothing happened. Help, please!

    Hello

    If the laptop is unable to complete the initial installation, and as it's brand new, my best advice would be to go back to the retailer you bought it and get it replaced.

    Kind regards

    DP - K

  • Windows could not complete the installation. To install Windows on this computer, restart the installation

    Decided to reinstall Vista business after that my lenovo x 200 could not start. After you have reinstalled, had to restart and now it appears

    "Windows is unable to complete the installation. To install Windows on this computer, restart the installation.
    How should I solve this problem?

    Hello

    1. may I know the exact error you received during initialization failed prior to relocation?

    2. do you know the exact reason for the failure of start?

    I will be asked to get in touch with the manufacturer of the system on this issue.

    Installation and reinstallation of Windows Vista, you can fallow the article below:

    http://Windows.Microsoft.com/en-us/Windows-Vista/installing-and-reinstalling-Windows-Vista#section_3

  • Windows could not complete the installation. To install Windows on this computer, run the Setup again.

    Hello, here is the thing.

    Reformatted a computer with recovery discs...

    Office to the top and everything looked ok...

    Windows Installer started and makes the computer reboot several times as usual.

    BUT NOW I have a black screen with a window saying "Windows is unable to complete the installation. To install Windows on this computer, run the Setup again. »

    I opened the Task Manager and closed a 'runonce' process, which got the Explorer will... But shit message will not go away, if I close the computer restarts!

    Why did I get this? How can I make them disappear? Windows has not installed correctly? Do I need to install any additional substance to compensate for this?

    + I just noticed there is no partition for recovery in my computer... you know? This thing of 2 GB next to Local disk c

    Hello, here is the thing.

    Reformatted a computer with recovery discs...

    Office to the top and everything looked ok...

    Windows Installer started and makes the computer reboot several times as usual.

    BUT NOW I have a black screen with a window saying "Windows is unable to complete the installation. To install Windows on this computer, run the Setup again. »

    I opened the Task Manager and closed a 'runonce' process, which got the Explorer will... But shit message will not go away, if I close the computer restarts!

    Why did I get this? How can I make them disappear? Windows has not installed correctly? Do I need to install any additional substance to compensate for this?

    + I just noticed there is no partition for recovery in my computer... you know? This thing of 2 GB next to Local disk c

    Hey Abraham G

    you use discs of recovery that are made for your brand and your computer model

    and if you have problems using the manufacturer's recovery disks, you will need to communicate with them about

    It's their recovery process not microsofts

    Walter, the time zone traveller

  • "Windows could not complete the installation", Y510P

    Hello

    Just got my new Y510P and realized it's impossible to start Windows.

    Initially it displays error "Windows cannot parse or process Unattend...» [... \unattend.xml] [oobeSystem] pass... »

    After reboot he start to display a different message - "Windows could not complete installation, restart the installation.

    The operating system is Windows 8.1.

    Looks like I'm not the only person having this problem. System recovery does not help, of course (as well as the graceful Lenovo tech support).

    I think that the problem caused by the incorrect unattend.xml file that fails to install any software because of this error and unnesessary blocking Windows to complete the installation.

    I see no other way rather than installing Windows from another source. I don't want to pay for another Windows license and instead return the Lenovo laptop, but perhaps there is another way?

    Problem solved.

    I contacted Lenovo support and they offered me to send recovery discs I received a few days later. I installed the cleaning system of records and have not experienced any problems since.

    I'm still not fully satisfied because I cannot reset the laptop to the factory settings without these discs, but I think I can live with that.

  • Vista: Windows could not complete the installation. Reinstall Windows. Stops at CRCDISK. SYS in safemode, all the time.

    A hard drive the HP dv2915nr laptop was dead. Installed a new hard drive and use the HP recovery CD. installs for 4 hours and then stops: Windows could not complete installation. Please re - install Windows again. Each facility is 4 hours. Because another install and it took 4 hours and then it restarts and stop at the same error. Now, I'm administrator (locked) - turn off when I pop in the recovery CD. Message: Your account has been disabled. Please, see your system administrator. I tried Safe Mode and loading Windows files stops at crcdisk.sys all the time and then restarts and displays: Windows could not complete installation. Please install again. Can't go in the office. Only restarts with these messages. Asked HP cat (3) Tech people and they do not have the answer. Said, could be a compatibility issue with the software. I ordered this CD of recovery on their part and he got yesterday. Now, they send in the laptop. So tried advice here. Please notify.

    I found the answer. HP Tech Support Chat did not know the answer. When you run HP recovery CD, don't hit the restart WINDOWS button when it asks. The software will do it for you automatically. It will take a while (several hours 1-6 hours) to complete. You'll know it's done when WINDOWS ask you information of language, country and keyboard. In other words, don't touch anything once you start the restore CD program. Leave it alone and it will fix it for you. IGNORE the pop-up restart.

    I can't believe HP has not even tell me that and 3 chat sessions with them was a waste of time. Last HP person ask me to send in the RECOVERY CD and the laptop.

    No help from anyone on this issue. :(

    BUT I thought about it. :)

  • Windows (8) could not complete the installation.

    I just bought a new HP2000 today. I get home and start of implementation. At the end of the process, when it * must * be showing me the office (or whatevert, they call the thing in W8), I get this error message. I click 'OK' and it reboots and starts the whole process. How "complete the installation?

    I'm about to take over and get a gateway or a Toshiba!

    Try running a system recovery tapping away to the F11 key, immediately after switching on. It's just to rule out the possibility of a flaky installation which can be corrected by a factory reset.

  • Download hp psc 2110xi could not complete the installation. where do you find the drivers for windows XP?

    I was updated the software and downloaded the HP Officejet and feature full CSP and later software.  Got to the end and the final Setup could not finish, so big red X.  Could not download it again because there was no uninstall file and received the message that the software has been installed successfully and to uninstall, and then try again.  Used the XP-install wizard, but he has not found all the drivers, but admitted the printer as new hardware found. (This printer was working before downloading the update).

    draw2tom

    Hi draw2tom,

    Follow the steps below and let me know what happens?

    First step: clear temp directory

    1. Type %temp% term or search programs and files of field
    2. Select all the files in this folder, and then press the delete key to remove. If you receive a message that the file is in use, you will need to ignore this file (s).
    3. Proceed to step 2 below

    Second step: downloaded and extracted to your system:

    1 download the drivers and full software features

    http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-19447-3&cc=US&DLC=en&LC=en&os=228&Product=79491&sw_lang=

    2. once the download is complete, double-click the file to extract the software.

    3. when the installation window opens, press the Cancel button to stop the installation

    4. tap folder in the race or search programs and files of field

    5. Locate and open the folder starting with 7z (example: 7zS2356)

    6. right click on the folder and select copy

    7. close this window and all open windows, and then in the Middle the desktop right click your mouse and select Paste. This will move the 7z folder on your desktop.

    8 open the 7z, that you just copied on your desktop

    9 open the Util folder

    10 open the CCC folder

    11 start the uninstall_L4

    12. once the uninstall is complete, restart the computer

    13. run disk cleanup from the tools Accessories\ system under all programs folder

    14. download and install the latest version of Adobe flash player

    http://www.Adobe.com/support/flashplayer/downloads.html

    15 open the 7z folder and then double-click the Setup.exe file that will be towards the bottom of the open window. Follow the instructions on the screen to reinstall your printer.

    Let me know if you are able to successfully install the software and driver and are able to print & scan?

  • Could not complete the installation because of the error "acrosup64.dll is not marked for installation.

    Hi all

    In the course of implementing in place process with my computer window Mobile 7-64 bit, it was display error message "acrosup64.dll is not marked for installation" interrupt the process.

    Someone help me overcome the question please. Thank you

    Acorbat issuse.jpg

    Have you tried just download the EXE and install it from there instead of the web installer?

Maybe you are looking for