Windows could not transfer files. An address incompatible with the requested protocol was used.

Similar Questions

• an address incompatible with the requested protocol was used

  After I have upgrade of windows 7 starter edition to windows 7 Home Edition premium, I can't do a bluetooth file transfer and the following message appears: an address incompatible with the requested protocol was used.

  Hello
  How do you transfer the file?

  Method 1:
  Try to perform the audit and the clean boot if this can help,
  Here is the link: http://support.microsoft.com/kb/929135
  Note: When you're done to diagnose, follow step 7 in the article to start the normal start

  Method 2:
  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link.
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry
   
  You can try the steps and check.
  (a) click Start and then click Run.
  (b) type regedit and then click OK.
  (c) locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {e0cbf06c-cd8b-4647-bb8a-263b43f0f974}
  (d) right click on the folder, click on delete.
  (e) exit and restart
   
  Method 3:
  Change settings for a Bluetooth compatible device
  http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-a-Bluetooth-enabled-device

• Error message: "could not cop files. Make sure that the target disk is not dead", during the installation of the drivers scanner Epson Perfection V500.

  Original title: the scanner driver update problems.

  Problem: I am trying to install a driver for an Epson scanner update.  I get the error message: could not copy files.  Make sure that the target disk is not read-only.

  I'm running Windows XP Home edition.  Scanner is an Epson Perfection V500 Photo.

  What I did:

  • A release with the support of Epson.  They tell me that I have the admin rights.  However, I am the administrator and log on as administrator
  • I downloaded the epson driver update, which is an executable zip file.  I right-click on the file, select Run As..., opt to run it as an admin user, enter my password and select run.  The files are decompressed, but at some point in the installation, I get the message "couldn't cop files.  Make sure that the target disk is not read-only.  (Target is C:\)
  • Furthermore, I installed this driver successfully on my other computer that is running Windows XP Professional

  Why not copy the driver files?

  Hi Passport35,

  You can try the following steps and check if it helps.

  Method 1:

  You can try running the fixit article and following cjheck, if it helps.

  Diagnose and solve the program installation and uninstallation problems automatically

  Method 2:

  If the previous step fails then I suggest that scan you SFC on the computer that would be a system file corrupt on the computer search and replace.

  a. click Start, click Run, type cmd in the Open box and then click OK.

  b. at the command prompt, type sfc/scannow, and then press ENTER.

  Note: the scan may take a while, so be patient. Windows allows to fix corrupt or missing files it finds. If the information of the installation CD is required to fix the problem, you may be asked to insert your Windows XP installation CD.

  Wait for the analysis of complete and then check if you can install the drivers.

• Windows could not find a certificate to log on the network

  So I try to connect to the network that appears, and then trying to connect but it with "Windows could not find a certificate to log on the network. Now, I tried unchecking security in the properties box and also to uncheck it to 'use windows to configure my wireless network.

  NONE OF THESE WORK FOR ME!
  Also attempted to fix the network, but he says that "windows could not finish repairing the problem because it is impossible to perform the following action: connect to the wireless network '"
  I am currently under SP2, but in the process of installing SP3.
  Help!

  This error usually occurs because you have specified a connection protocol 802. 1 x.  You must configure your properties to uncheck this box.  See the following article:

  "Windows could not find a certificate to log on the network.

  <>http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-Networking/window-was-unable-to-finad-a-certificate-to-log/f68d2ea6-51c4-4B86-a5de-da4d06afb50a >

  HTH,
  JW

• error message: "windows could not find a certificate to connect to the network.

  My NetGear wireless icon shows this error message "windows could not find a certificate to connect to the network.

  Hello

  Did you change your computer before this problem?

  You can follow the procedure in the article.

  Unable to connect to the network: Validation and certificate in Windows XP and Vista errors

  http://KB.NETGEAR.com/app/answers/detail/A_ID/7334/~/unable-to-connect-to-network%3A-validation-and-certificate-errors-in-Windows-XP

  Alternatively, you can contact Netgear support to improve assistance in this regard.

  Welcome to the NETGEAR support

  http://support.NETGEAR.com/

• Internet connection issues "Limited or no connectivity." and "windows could not find a certificate to log on the network.

  I'm so unable to connect to the internet?

  Hello.

  I'm so unable to connect to the internet.

  Since I've renamed our WiFi network and add a WEP key, I have problems with wireless connection on my
  Windows XP computer desktop, which is a Dell Dimension 4700.

  The questions that I get connection are...

  "windows could not find a certificate to log on the network.

  "Limited or no connectivity."

  I did all the solutions I could try to fix the connection problem!

  1. once I received the message "limited or no connectivity", I click with the right button on the connection and click on repair. It is not always connect for me and I got the "limited or no connectivity message.»

  2. then, I disabled the network connection and then enabled. That no longer works.

  3. I tried to withdraw from the ordered list of connections, and it still doesn't work.

  4. I checked the driver manager, and initially the Ethernet driver was outdated and missing of its pilot. He had a yellow question mark with a black sign and yellow with an exclamation mark inside.

  5. I used DriverZone, downloaded the driver, installed and rebooted the computer after the installation of the it. Apparently, it worked. But I could not always connect.

  6 I have ensured that I entered the correct WEP key, and then adjust the settings correctly. I did it like 10 times in a row and would not always connect.

  7. I tried to go to the command prompt and typed in IP Config/All and that's what I mean.

  Windows IP configuration
  Node type: unknown
  Active IP routing: no
  WINS proxy enabled: no
  ETHERNET connection to the Local network card
  State of the media: Media disconnected
  Description: Intel PRO/100 VE Network Connection
  Ethernet card 2 wireless network connection:
  Suffix the connection-specific DNS: (EMPTY)

  8. after that, I typed the command: ipconfig/release
  and then I got this error...

  No operations can be performed on the connection to the local network, although it has its media disconnected.

  9. after that, I tried Googling for some solutions, and the solutions I found were not any use.
  A solution was

  10. opening of Services...
  Start | Run | Type: services.msc | Click OK |
  Scroll down to and double-click Client DNS | Set to automatic on startup
  type |
  Click apply | Click the Start button | When it starts, click OK
  Do the same for the DHCP Client.
  Do the same for the remote procedure call (RPC).

  and it still doesn't work.

  11. when I look in the menu network connections, I see my connection with a lock on the side, with a red X under the lock and key. In the description, I see not connected, protected by a firewall. How could I remove the internet connection firewall? I disabled the firewall and that did not work.

  12. I tried to uninstall and reinstall the network card and who does not work either.

  It is not the network itself that is the problem.  It is not the modem or the cable. There are no disconnected son or something like that. We have other computers in the House and the internet works fine on other computers. As I said, since I renamed our WiFi network and added a WEP password, I had problems with connecting to my Windows XP computer.

  My computer has updates that must be installed as well. Updates would fix the problem? I just need to have internet.

  What should I do? Thank you for your time.

  Sincerely,

  Justin

  Have you tried to set the value of the link speed/duplex mode? I had the same problem you describe. Your card is only capable of 10/100 communication.

• NO wireless network connection - message "Windows could not find a certificate to connect to the network Shaida. How to fix this problem?

  I had just restored my Thinkpad T60 the default setting. Reformatted and reinstalled Windows XP, but I am unable to connect to the wireless network connection - message "Windows could not find a certificate to connect to the network Shaida.

  Shaida is my wireless modem.

  How to fix this problem?

  Before the resumption of connection Internet worked normally.

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://support.Microsoft.com/kb/870702

  It will be useful.

• Unable to connect on the internet on another computer - "Windows could not find a certificate to connect to the network (named).

  When I try to connect to internet on my other computer I get a message saying "Windows could not find a certificate to connect to the network (name)". It's only since I've had a second computer as it does on my old computer which is

  a laptop HP Pressario with Windows XP Home Edition. Someone told me to go to authentication in wireless networks, but can highlight something here as everything is gray.

  Hello

  · What type of encryption do you use on the router?

  · You have the latest drivers for your wireless network card?

  Make sure the authentication IEEE 802. 1 x wireless card is disabled, and check if that helps.

  a. Click Start, then select run.

  b. term ncpa.cpl type dialog box and then click OK.

  c. right click on wireless network connection icon and select Properties.

  d. click the wireless network tab.

  e. click on the properties button next to remove it.

  f. click on the Authentication tab, and then clear the authentication 802. 1 x IEEE select this network check box.

  g. click OK to update the settings.

• I could not transfer file usin bluetooth of my acer v3-571

  I have OS Windows 7, Bluetooth in my laptop is not working or I could not transfer and receive files via Bluetooth.

  Hello

  I understand that the Bluetooth file transfer fails in your computer.

  I would be grateful if you could answer the following questions:

  1. did you of recent changes made to your computer?

  2. What is the exact full error message that you receive?

  I suggest to follow the steps below and we update on the State of the question.

  Method 1: Run the fixit proposed below and check:

  Bluetooth devices do not work correctly on a computer that is running Windows 7:

  http://support.Microsoft.com/kb/980396

  Method 2: If the previous step fails then check and make sure that the Bluetooth function is running on the computer

  (a) click Start, type services.msc in the Search box and press on Enter.

  (b) right click on the Bluetooth support service, and then click Properties.

  Make sure that the service status is set to "started" and the service type is set to "automatic".

  Reference:

  Add a Bluetooth device to your computer

  http://Windows.Microsoft.com/en-us/Windows7/add-a-Bluetooth-enabled-device-to-your-computer

  If you have additional questions, or if this problem persists, come in and we will be happy to help you.

• Windows could not configure one or two components of the system.

  I get this message after completing my update, Vista Home Premium 64 Vista Ultimate 64. All solutions?

  Hello

  1 you have a Windows Ultimate Upgrade disc, a complete edition of the full Windows disk or a Windows Anytime Upgrade disc?

  2 - is Windows XP or Windows Vista already exist on the computer before you install Windows Vista Ultimate?

  Currently, I suggest referring to the following troubleshooting article and thread:

  Windows could not configure one or more system components

  http://forums.Microsoft.com/technet/ShowPost.aspx?PostID=2409427&siteid=17

  Error message when you try to upgrade Windows Vista to a more advanced version of Windows Vista: "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation.

  http://support.Microsoft.com/kb/946078/en-us

• Windows could not start... I need the disk installation?

  Hi, so I recently uninstalled Windows 7 by accident... And I tried to make it work, but it won't, so I need the disk. I contacted microsoft asking if I can get another disc or something. And they said to go to m6mobile.fr. So I went on it, got the Windows 7 USB/DVD download tool, I got the ISO file on my USB key. And now I have everything. So I took out the laptop I did all the stuff on, I then went to the computer to install Windows 7. And it still does not work! I plugged the USB with the ISO file and then restarted, and it still doesn't work? Can someone help me? I stayed until 02:00 am trying to solve this problem!

  Thank you! Here's what the problem...

  (Sorry for the small image!)

  

  Your problem is the link below:
  http://www.SevenForums.com/BSOD-help-support/209281-boot-manager-status-0xc000000f-boot-selection-failed.html

  What is your computer brand and model?

• Windows could not start database engine of filtering on the computer local error 5 access denied. Please help someone...

  My OS is windows7 32 bit and Quick heal total security pro is loaded

  Hi Sangramkeshari,

  1. Once you get this error message?

  2 has there been recent changes made on the computer before the show?

  I suggest you follow the steps provided by rap2pac on June 23, 2012 and check if this may help.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/cannot-start-Windows-Firewall-service-error/e5c277c7-df4d-4253-91EC-5b3314488dae

  Registry warning: Back up the registry

  For more information, see the link and check.

  http://blogs.technet.com/b/networking/archive/2011/06/08/the-Windows-Firewall-service-fails-to-start-introduction.aspx

  Please update us with the results and we will be happy to help you.

• Windows could not start File: \Boot\BCD status: 0xc000000f on a HP G6 2053ef (RESOLVED)

  HI, I have this on my HP G6 2053ef, and I have an error message indicating that "an error occurred" trying to read the boot configuration data and also file: \Boot\BCD status: 0xc000000f

  How can I solve it please, I have windows won start t all hekp would be much appreciated.

  Kind regards

  Yvouille

  Hello

  The following assumes that you are running Windows 7.

  If you do not, use another PC to create a rescue CD Windows 7.  Download the ISO relevant among the links below - if you are unsure of the version, your laptop is listed as coming from a 64-bit installation.

  Windows 7 32 bit

  Windows 7 64 bit

  You must use an app like ImgBurn to burn the ISO to a CD-( Note: you can deselect additional software during installation of ImgBurn options)- hereis a guide on the use of ImgBurn to write an ISO on a disc.

  One time created, or if you already have this, typing away at the esc key when you launch Notepad to open the Start Menu.  Insert the rescue CD.  Select boot options (usually f9), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

  When loading, select repair your computer and choose the command line.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

  Bootrec.exe

  bcdedit/export C:\BCD_Backup

  c:

  Boot CD

  BCD attrib s h - r

  Ren c:\boot\bcd BCD.old

  Bootrec /RebuildBcd

  Bootrec /fixmbr

  Bootrec /fixboot

  Remove the rescue CD and try to restart the laptop.

  Kind regards

  DP - K

• Use windows could not restore because there are errors in the disk OS (C).

  My windows vista system is freezing. (Nothing new installed recently)

  I tried to restore the system to an earlier date, but references to message windows cannot be done because the disk OS (C) contains errors.

  Can I remove these disk errors. or should I just replace the drive and try again (disaster!)

  Your hard drive manufacturer will have a utility bootable disk for verification.

  Alternatively, you can run chkdsk from base; Computor > C: properties > tools > error checking

• Windows could not parse or process unattend answer file

  I try to install Windows7 on virtual machine with VMWare.  I get the windows could not parse or process of response to the message file Unattend.  I read that the product key valid maybe problem.  My key has been verified as valid.  What should I try next?

  Hi Stephens,

  The issue of Windows is more complex than what is generally answered in the Microsoft Community Forums. Appropriate in the TechNet Forums. Please post your question in the TechNet Forums.

  You can check the link to post your question:

  http://social.technet.Microsoft.com/forums/en/w7itprovirt/threads

  I hope that helps!