Windows does not start with the second internal HDD connected

Similar Questions

• Windows does not start with the 4G mobile broadband modum connected?

  It's just that, bunch gets to the windows startup screen but no symbols and no further?

  TREV,

  I appreciate that you have checked with the manufacturer of the modem for a pilot updated already.  You can try also usefully - MS Update site

  Microsoft update catalog service - Log in to your computer as an administrator first, use IE not another browser, navigate to the site, look for the material of brand & model.

• My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM.

  My pc says that windows does not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM. It is said it can be repaired by using the original installation CD, but we do not have. Any ideas please?

  The file is missing or corrupt is one of your files in the system registry.

  By far, the best way to recover from this is to go to another computer and create a free Hirens Boot CD.
  Download Hirens: <> http://www.hirensbootcd.org/download/ > (link at the bottom of the icon of the disk)
  Hirens CD burning <> http://www.hirensbootcd.org/burning/ >

  Once you create the CD, and then start your system of problem with this CD.  In the first window, select "Mini Windows XP" and wait for the system to start.  When it starts, go to the Hirens Boot CD menu and select
  Register-> Registry Restore Wizard.
  then follow the prompts.  This wizard will return a copy of your registry database from backups that are stored with your system restore points.  After the restoration, stop, remove the CD and restart.

  When you start your system, it is recommended to perform a system restore operation to ensure the consistency of your system
  "How to restore Windows XP to a previous state"
     <>http://support.Microsoft.com/kb/306084 >

  Also, this error is almost always accompanied, if not caused, the corruption of the file system.  Also a good idea to perform a check disk (chkdsk) operation with the option "repair".
  "How to perform disk error in Windows XP check"
     <>http://support.Microsoft.com/kb/315265 >

  The hard way to get back is covered in the following Microsoft KB article, but if you have installed a large number of service packs for your installation of XP, I don't give you many chances to get past part 1. (And there's also an installation CD to access the Recovery Console)

  "How do I recover from a corrupted registry that prevents Windows XP boot"
    <>http://support.Microsoft.com/kb/307545 >

  HTH,
  JW

• Windows does not start after the update...

  Hope someone can help with this,

  I just installed the update sp1 for my computer for Windows Vista Premium Home dir all installed with no problems, but when I restarted my pc, Windows wouldn't start. The only thing that is on display is a black screen with Windows Error Recovery on top, then he said "Windows does not start. A recent hardware or software change might be the cause. I tried to restart it in different ways, but nothing. Then he said: I have to insert my OS drive to try to fix, but that's not even start. Everyone knows about this problem? This has happened right after that I installed the update...

  L.Butler,
  Are you able to boot from your Vista DVD or recovery partion and run the Startup Repair tool?  If you do not have a Vista disc so make sure that your computer is configured to boot from the CD drive before booting from the hard drive.  Once you start with support for Vista select the "Repair your computer" option and first run "Startup Repair".  If that is not correct the problem then boot with Vista support and select the option "System Restore" and choose a date prior to the update install.
  Once you are able to boot normally again, then I suggest that you are looking for virus\malware.  SP1 was released in April 2008.  So if you install earlier means there may be other problems on your system.  If you have a backup of your current personal data then I recommend to do a clean restore to install\factory.  Then immediately install antivirus software, and then do all Windows updates before installing other software. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Machines Windows does not start with 2 virtual disks different on 2 different

  Hello

  With the help of esx.3.5.0 update 3

  I have a problem where if I have a new VM to win 7 or Win 2008 r2 with or without vmtools.

  If I reboot it up to 10 times without having to install anything, whether he'll join the black windows loading screen, then restart and then restart and try to start in safe mode, it still does not start.  the machine rendering it useless.

  The single element only on these virtual machines is as follows.

  Windows machines have 2 different virtual disks 1 on a lun, VMFS (vmfs version 3.21 c:) and a RDM VMFS (d :))

  3 questions

  Is it a problem to have 2 different discs with 2 different stores file types?

  Would this questions we see above?

  Also, I thought that you might not? VMotion/clone? a virtual machine if she drives in 2 different places?

  I tested and I can vmotion live VM with records stored on 2 different LUN.

  Hello.

  With the help of esx.3.5.0 update 3

  I have a problem where if I have a new VM to win 7 or Win 2008 r2 with or without vmtools.

  If I reboot it up to 10 times without having to install anything, whether he'll join the black screen windows loading and then restart and then restart and try to start to > safe mode, it will not even start.  the machine rendering it useless.

  Windows 7 and 2008 R2 are not supported in this version.  5 update brings support for these two operating systems.  Go to U5, maybe it's the solution.

  3 questions

  Is it a problem to have 2 different discs with 2 different stores file types?

  Laughing out loud

  Would this questions we see above?

  It is unlikely.

  Also, I thought that you might not? VMotion/clone? a virtual machine if she drives in 2 different places?

  I tested and I can vmotion live VM with records stored on 2 different LUN.

  VMotion requires shared storage.  Local storage would be a problem if you tried to change hosts.

  also would it be a problem if 1 store was running 3.2.1 vmfs and other store runs 3.31 and a v on each disc is used for the VM 1?

  Lol this is explained in KB 1005325.

  Good luck!

• BlackBerry 8250 new smartphones does not start with the connected SIM card

  I'm having a problem with my new Blackberry of Virgin Media (mobile).  I just got it and when I have a connected SIM card I only get the loading screen timer and the blackberry does not start.  If I have no connected SIM card the device starts in the operating system, but was told that there is just no SIM connected (obviously).  Once I put the SIM card in again once it is stuck on the loading screen.  As you probably already figured out that I did many resets hard with the battery pull and it has not solved the problem.  A consultant because it would be greatly appreciated because the only advise I got support was remove the boot of sim and put it back and start again duh!

  Carrier - Virgin Media / Vodafone
  Model - 8520
  Version of the OS - 4.6.1
  Free space - 130679088 bytes

  BT device - I have the details as HDW - 22736-002 Rev 1 Ver 2 4509 (is that correct?)

  Apps & free space - nothing installed new device installation is not complete.
  Blackberry 4.6.1 Basic application
  Basque 4.6.1
  Galician 4.6.1
  softwqare system BlackBerry 4.6.1
  1.0.1.20 Application Center
  Attachment Service 4.6.1
  4.6.1 cards
  Messenger 4.6.0
  BrickBreaker 4.6.1
  browser 4.6.1
  documents to go 1.003.018
  configuration of e-mail application 4.6.1
  help 4.6.1
  Klondike 1.4.8
  4.6.1 Memopad
  password keeper 4.6.1
  Phone 4.6.1
  Sudoku 1.0.11
  4.6.1 tasks
  King of hold'em Texas 2.3.0
  Word Mole 4.6.1

  1 is the news provider's SIM card?

  Old to another device?

  2. do not place you a memory card in the camera?

  New media card?

  or from another device? What device?

• Machine virtual Windows does not start on the MBP retina with 10.9 Mavericks DP3

  Mavericks 10.9 DP3 running on a MacBook Pro 15 "with Retina display 2012 and the TP2013 merger causes the following problem:

  None of my virtual machines created in Fusion 5.0.3 will begin.  I have Windows 2008 R2 and Windows 8 x 64.  I also tried to create a new virtual machine from Windows 8 x 64 with all defaults under the technology preview, and the same problem occurs just after the BIOS screen clears, and above all expected Windows 8 installer would (do not press any key to start from DVD, etc.).

  VMware Fusion has encountered an error and has stopped Windows.

  Click on restart Windows to start Windows again. Click report to collect data and to ask the support of VMware.

  [Ignore]     [Report...]     [Restart Windows]

  Ignore everything stops the system down

  I have reports of existing Windows Server 2008 R2 and Windows 8 x 64 virtual machines as well as the test of the virtual machine.

  Windows 8 x 64 gives this error in a black translucent dialog box appears when starting a VM Windows 8 x 64, nine (before installation) or not:

  No 3D support is available in the host.

  3D virtual machine functions will be disabled.

  Windows Server 2008 R2 VM will display the EFI boot screen, then if you press F8 and choose recovery it will start loading the recovery files, but when it gets to the point where windows graphics loading screen with the Windows logo would be (after "Windows is loading files" text screen with the bar at the bottom, but before the GUI) you only ever see the graphic display and it crashes

  Opening of Fusion 5.0.3 and closing the Tech Preview, the virtual machines will be load without problem; no boot time error either.

  Seems to have something to do with the graphics, but still - no similar problems with 5.0.3

  Hi Siobhan,

  Thank you for reporting this issue. I checked your vmware.log and found this problem has been reported by an internal user, the internal PR is 1047175. Now it is fixed in the latest internal version. Since 10.9 comes after tech Fusion preview release, the issue is expected. Please be patient to wait for the next release of Fusion. Thank you.

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• C50-A-19 t satellite does not start with the battery mounted

  OK, first post here.

  I see similar questions coming, but as they are never QUITE the same, I am that posing in a new thread.

  I left my Satellite from one day to the next (do not remember if I had put off, or he simply had 'gone to sleep', but it has been connected to the grid).

  When I got to reboot, I got a power light on, but screen blank (black). After reading a few similar complaints on the internet (via another laptop!), I tried to remove the battery and power from the grid.
  This worked well (I write him in this state right now).

  But whenever I put the battery and try again, it will fail in the same way.
  I tried this company "press and hold power for 30 seconds" without success (but I'm not 100% sure of the EXACT procedure actions sequence).

  I have a few questions:

  (1) I take the laptop away from my office - is there a problem with everything just works like this (i.e. of the grid, with no battery inserted) indefinitely?

  (2) in any case, I want to solve the problem.
  If the battery has run COMPLETELY flat, and that the laptop can not it lights but also operate normally?

  Alternatively, is probably that the battery has not experienced a catastrophic failure and simply needs to replace?
  If so, I'll just buy a. BUT...

  What I don't want to do, is to pay for a costly spare battery, to find that it was actually another factor at the origin of the problem, and I'm back to square one and out of Pocket!

  Any advice would be welcome.

  Thank you

  Mike

  Hello

  According to your assignment, in most cases, you use the laptop connected to the power adapter but no battery. Is this correct?

  First we need to know that if the AC adapter is plugged in, the laptop should work correctly with - and without inserting the battery.
  If you unplug the AC adapter, the laptop should automatically switch to battery power. In this case, it is important that the battery is pretty cool power to provide the power for the laptop.
  In case the battery is empty, the laptop will not light.

  I recommend to insert the battery plug the power adapter and charge the battery for a longer period of time.

  You should also check if the battery is recognized by the Windows system and the battery charge indicator (battery in the taskbar icon) shows the State of battery charge.

  In case the battery is fully charged and the laptop does not work using the battery power only, you should test the new battery.
  If new battery does not solve the problem, s for laptop hardware needs an audit.

• Satellite Pro 460 does not start with the new drive in

  I recently received a Satellite Pro 460, but he had no hard drive.
  It starts great without a disc in but as soon as I put a new hard drive in it does not start.

  I thought that it might be again a hard drive, so I pulled out my old Toshiba Satellite with my old drive to work, and yet, it does not start.

  Someone has any ideas why this is and what I can do about it

  I think that you can not do much. Satellite pro 460 CDT, for example, comes with 2 GB of HARD drive. If you try to get it work with similar HDD without success, it may be defective IDE port on the motherboard.

  What HARD drive you are trying to use on this good old classic?

• Satellite A30 does not start with the USB device connected at boot time

  Hello

  I have a Satellite A30 and sometimes it does not start.
  After turning on, not even the BIOS starts.
  even if sometimes the BIOS starts, but the OS does not load.

  I figured out that its related to USB devices connected at boot time.
  If no USB devices are connected, it starts without a problem.
  Even if the start-up is suspended, as soon as you unplug start it BIOS USB devices.
  Its ok to connect USB devices later, once the system has started.
  I disabled "removable devices boot" and "network startup."
  just in case, but it makes no difference.

  BIOS is version the most recent (1.70) and it comes up with all kinds of USB devices.
  printer, mouse and (self-powered) external USB hard disk.

  Is this a known issue?
  There is no known workaround solution?

  Hello

  I put t know why this happens, but it has to do with the BIOS.
  The same thing happened on my old laptop. I couldn't start my unit while the USB printer has been turned on and connected.
  The only solution is to disconnect the external USB device during the boot process.

  RSY you should check if the order of boot in the BIOS has been on the HARD drive first.

• C870-19(r) satellite does not start with the new SSD

  Hello

  I will update the Toshiba Satellite C870 19(r) with a Pro 840 Samsung SSD, but it does not start.

  He said: not found system.

  Post edited by: joch333n

  None found system means that there is no system installed on the SSD drive...

  What you trying to do?
  You start from a disk in order to install the new system?

  In this case, you should disable startup secure in the BIOS.
  I also recommend moving from UEFI mode MSC!

• Laptop does not start with the connected usb device

  Hello
  Voila, I have a Sp6100 Pro Satellite, when I try to start whith a usb printer is connected, the laptop does not start. I have the latest version of the bios 1.90.

  THX,
  Barzot @+.

  Hello

  What you mean with start won t at all? Is there any kind of reaction if you press the power button / stop?

• Why my DVD does not start with the film and not on the menu?

  HI -.

  I'm just starting to use yet.

  I import my film as a timeline, my PSD as a Menu, link the button in the menu to the timeline and tie the end to the Timeline action to return to the Menu.  I get no error, when I check prior to construction.

  But when I play the DVD, the menu is entirely ignored.  The movie just started.  End action works and I can navigate the Menu using the remote control, but I want the disc to start with the Menu.

  What Miss me?

  TIA your instruction.

  JL

  Hello

  In this case, first of all, I would check my first piece of the project. You can check the first play in the drive properties in the properties panel.

  Click on the disk icon in the window of the chart and look at the properties of the disc in the properties panel.

  If you want your menu to play first you insert the disc in the drive, then this menu must be set as the first piece of theatre.

  I hope this works.

  Thank you

  Ramesh.

• Windows 7 does not start with the new msi motherboard

  Yesterday, I bought a new motherboard, processor and 8g of ram in my computer. After all what adjustment and replacement of my old motherboard with the new, I started my computer to find that Windows 7 unbootable not. Instead of windows 7, I get the screen click on BIOS II (2). The configuration screen allows me to launch Winki but not Windows 7 because it was not found. The motherboard came with a utility disk drivers msi and AMD chipset which, when inserted in my hard disk, loads up to Winki. This version of windows 7 (Home Premium 64-bit) came pre-installed with my old mother/computer(Thus, I do not have the windows 7 installation disk) card. Is there a way I need to activate Windows 7 on my new motherboard?

  Hello

  Well, you have some problems. First of all, with a new motherboard you need a new copy of Windows - not only the DVD, but a whole new product key must be purchased. It's just the terms of the license: a new motherboard is equivalent to a new computer, and each computer must have its own copy of Windows.

  So where you buy your copy of Windows 7, I would make sure that it came with a DVD image. Otherwise, you can tell us which version of Windows 7 you (will) actually buy, and we can send you a link to the copy of the DVD for this version of Windows 7.

  To purchase a copy of Windows 7 you can check Newegg.com, here: http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&DEPA=0&Order=BESTMATCH&Description=windows+7&N=-1&isNodeId=1 .

  I hope that answers your question.

  Kind regards

  BearPup