Windows has prevented my device Infarred "Serial Cable using IrDa Protocol" to 43 of the Labour Code

Similar Questions

• How to fix it. Problem of "Serial Cable using IrDA Protocol" it says Code 43 I use window XP

  How to fix it.  Problem of "Serial Cable using IrDA Protocol" it says Code 43 I use window XP I have no idea what the point is that the origin of the problem. Is there a link I can go to-to solve this problem? Thank you in advance.

  Yes, just right click on the device in Device Manager and select uninstall.  When you restart, Windows can detect the device and try to reinstall.  If the error is returned, post back - if this error is related to a laptop that has an infra-red (IR) integrated connector, you can disable this device in the BIOS.

• Serial cable using IrDA protocol does not work correctly. Steve Stephens, * address email is removed from the privacy *.

  The difficulty it Center Microsoft said that my serial cable using IrDA protocol does not work properly.

  Appreciate any suggestions on how to solve this problem.

  Steve Stephens, * address email is removed from the privacy *.

  Hi, Steve Stephens.

  Did you run the fixit available in the link below?
  Hardware devices do not work or are not detected in Windows

  Method 1: Check for any error message in Device Manager

  When a device is not functioning, Device Manager also typically displays an error message with an error code that comes with it. First, search for errors in the Manager of devices to do this, follow the steps below:

  (a) open Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager.

  (b) If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  (c) in the Device Manager, find your device, and then double-click the device name.

  (d) If an error code has been generated, the code appears in the status area of the device under the general tab

  
  Method 2: download and install all available Windows Update

  Install Windows updates
  http://Windows.Microsoft.com/en-us/Windows-Vista/install-Windows-updates

  Method 3: Download and install SP2

  Learn how to install Windows Vista Service Pack 2 (SP2)
  http://Windows.Microsoft.com/en-us/Windows-Vista/learn-how-to-install-Windows-Vista-Service-Pack-2-SP2

• How can I correct a problem of "Serial Cable using IrDA Protocol"?

  I have added a second hard drive of my computer. According to Windows Vista it works, however; After I did I received a ' infrared devices message both in my control panel, that has never been there before and in the devices Manager pane.» Also, in the Device Manager, I got a "serial cable using IrDA #2. Protocol. I don't know what is "IrDA". the best I can get out of windows, is that it is a code 43. When I use the check for button solutions I am told that the drivers for the infrared problem is that the driver software is not installed. If I click on the button get the updated drivers, which is to say that the latest drivers are already installed. I do not know what device does not work, and I don't know what is infrared device, and what is a "IrDA Protocol". I can't find a definition of these terms or anything like that ales thereon in respect of aid. So I was not able to find anything about them in the windows of the library of the line. I don't know where to get more information about this problem. Please help me. Thank you.

  Install the hotfix from the link below, should resolve your problem

  http://support.Microsoft.com/kb/941997

• AMD Radeon HD: Windows has stopped this device because it has reported problems. (Code 43)

  In my device manager, in graphics cards, for my AMD Radeon 7500,7600 M graphics card in the series, the properties display the following error message:
  "Windows has stopped this device because it has reported problems. (Code 43) »

  I uninstalled the drivers and reinstalled them - it's the 12.104.0.0 version, which I have confirmed is the last. I have the Catalyst Control Center installed as well.

  Can someone help me understand this error? Why would he stop? What would be my next steps to try to solve it?

  See you soon,.

  Sam

  Hi thanks for trying, but the Dell drivers are those which deal with the problem of restart.

  I find the most recent driver Intel HD 4000 (Win64_15313_intel) and installed version, then I installed the latest drivers AMD (13-4_mobility_win7_win8_64_dd_ccc_whql_AMD) on the site of AMD. This solved my problems and my graphics card works fine now.

  So yes, just repeat those it tells me to install when I get my serial number and OS (Windows 7) were:

  Intel: 5423_Video_Driver_T6XGJ_WN_8.15.10.2669_A02

  AMD: 5423_Video_Driver_VGR24_WN_8.951.9.0_A02

  And these caused problems without end - the graphics card would not work, and then when I installed drivers from AMD, Dell, it would cause my system to reboot every 2 or 3 minutes. It looked like some kind of incompatibility between the two graphics cards and the drivers provided.

  The other representative of Dell told me the same thing that you - so I wanted to post my solution in case anyone else has this problem.

• I think Windows has stopped this device because it has reported problems. (Code 43) when connecting iPod to the PC.

  Original title: Code 43 problem

  iPod is no longer detected when plugged to the USB port.  Instead, I get the following error message: "Windows has stopped this device because it has reported problems. (Code 43) »

  Crisis averted!  On another head shot... I thought that maybe the problem could be in the sync cable since the Apple store employee had no problem with the iPod.  I bought a new cable and the computer immediately recognized my iPod.  The old cable is now in the trash.

  Thank you for your help.

  Bob

• Error: Code 43; Windows has stopped this device because it has reported a problem whiel trying to use Cyberlink Webcam

  Title: cannot activate cyberlink webcam

  My cyberlink webcam was working fine until today. It will not turn on. After you apply the troubleshooting suggestions, I received a reply as follows: 'windows has stopped this device because it has reported a problem. (code 43) What is - this and how to solve my problem. I have a HP Pavilion g6. Help, please!

  Hello

  -Did you do changes on the computer before this problem?
  -What is the operating system installed on your computer?
   
  The error code you get is due to one of the engines that controlling the device notified the operating system that the device has failed in some way.
  Method 1: Run the Microsoft FIXIT from the link and if the problem persists.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us
   
  Method 2: Uninstall and reinstall the USB controllers
  You can try to uninstall the drivers and also scan for any hardware changes in Device Manager.
  (a) open Device Manager by clicking Start , and then type Device Manager.
  (b) expand the Controllers of Bus USB section by clicking on the '+' sign.
  (c) Uninstall each of the devices under the USB Controller section by right-clicking on each one, and then click Uninstall.
  (d) close the Device Manager and restart the computer.
  Windows RE-automatically install the USB controllers in your computer, without you having to do anything further. Your computer is now running properly USB devices.
  For reference:
  Updated a hardware driver that is not working properly
  http://windows.microsoft.com/en-us/windows-vista/Update-a-driver-for-hardware-that-isn ' t-work properly
  
  Method 3: If the problem persists, I suggest you to follow the steps from the link and check if it helps.
  Code 43: Windows has stopped this device because it has reported problems
  http://TechNet.Microsoft.com/en-us/library/cc725873 (WS.10) .aspx
   
  Hope this information helps.

• Port_ #0003.Hub_ #0005, Windows has stopped this device because it has reported problems. (Code 43)

  my computer did not recognize my usb to the printer device.

  Hello

  1. what operating system is installed on the computer?

  2. this printer was working on the computer before?

  3. have you made changes on the computer recently?

  4. What is the brand and model of the computer?

  5. What is the brand and model of the printer?

  Try the following steps.

  Method 1.

  Connect the printer on another computer and check if the printer works fine.

  Plug another usb printer and check if the printer works fine on this computer.

  Open the hardware and devices Troubleshooter: http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2.

  I also suggest you follow the steps in this article.

  Install a USB device: http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  Printer in Windows problems: http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Refer.

  Code 43: Windows has stopped this device because it has reported problems: http://TechNet.Microsoft.com/en-us/library/cc725873%28V=WS.10%29.aspx

  I hope this helps.

• Error code 43 (Windows has stopped this device because it has reported problems) on nividia 8800 gt graphics card

  I have a computer with dual nvidia geforce 8800 gt graphics card graphics cards, but I recently started getting the following in my device manager error message: "Windows has stopped this device because it has reported problems. (Code 43) »

  I started getting this message out of the blue after moving from my computer to another room.  I knowingly did not change anything on my PC and have been released for about 2.5 years with no real problems to speak of her.  I tried to uninstall and reinstall the latest driver from nvidia and had no luck.  I don't have access to the nvidia due to the device being disabled control panel.  Also I tried to restore my PC to a previous save point with no luck as well.  A short reading on nvidia forums led me to try a registry scan and repair, but alas it was without result.

  Any advice on what could be the cause of the problem and the best solution would be greatly appreciated.

  Hi rd,.

  You could try to remove one of the cards, then update the driver.

  They should use the same driver and may be coflicting at startup.

  You should also check the power supply if it is a few years old.

  Also make sure it is off enough electricity for the installation of the split card.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error "Windows has stopped this device because it has reported problems (code 43)" after the computer start in low resolution and remains after the connection

  Original title:

  Problem occurs intermittently, but almost every time at the first start the morning. The problem can be seen during the POST and the rest after logon. After several reboots, he can come good, but at the next restart could be bad. One clue is that the Device Manager said that to display card NVIDIA Ge Force 8400 GS that "Windows has stopped this device because it has reported problems (code 43)." Driver update says I have the latest driver insalled, version 8.17.12.9573. Help, please

  Have you tried to update your BIOS? Are there updates the firmware for your video card?

• Windows has stopped this device because it has reported problems. Toshiba R830 (code 43)

  my show toshiba r830 Windows has stopped this device because it has reported problems. (Code 43)

  Windows has stopped this device because it has reported problems. (Code 43)
   
  Diagnosis
  A device driver has notified the operating system that the device failed.

  Resolution

  Hardware devices do not work or are not detected in Windows FIX IT:

  http://support.Microsoft.com/mats/hardware_device_problems

• Error: "Windows has stopped this device because it has reported problems. (Code 43)

  Original title: chip Blue tooth

  Summer just check via the Device Manager and found my 'CSR Bluetooth Chip' has a problem: "Windows has stopped this device because it has reported problems. (Code 43)' checked the update driver and it's all good, no matter what can shed light on this problem?

  Hello Brady.

  Thanks for posting your concern to Mirosoft forum, I'll certainly help you with this problem.

  You might face this problem because damaged or obsolete Bluetooth drivers. I suggest you follow the steps below and check if it helps.

  1. Did you of recent changes to the computer before this problem?
  2. When you receive this error message?
  3. Your computer will detect the Bluetooth device?

  Please follow the methods and check the status of the issue.

  Method 1: Run the diagnostic tool

  The diagnostic tool is a tool that will check the hardware attached to the computer for all known with him of the issues and provides details and how to fix them. Follow these steps and run the troubleshooter.

  Connect the devices to the computer.

  Hardware devices do not work or are not detected in Windows

  If the problem persists, follow method 2.

  Method 2: Uninstall and reinstall the Bluetooth driver.

  Follow the steps below to uninstall the Bluetooth driver.

  1. Click Start
  2. Click on Control Panel.
  3. Go to system and security.
  4. Under System , click Device Manager.
  5. You can get driver Bluetooth and expand it.
  6. Right click on the driver Bluetooth and select Uninstall.
  7. Now, restart the computer and check the status of the Bluetooth driver.

  See also:

  Code 43: Windows has stopped this device because it has reported problems

  Devices & drivers

  Let us know if you need more assistance. We will be happy to help you.

  ____________________

  Thank you best regards &,.

  Isha Soni

• iPhone 5 Code 43 Windows has stopped this device because it has reported problems

  Then, only in the past few days windows can't recognize my iPhone when I plug it via USB, and so does not charge or sync with iTunes. When I open the Device Manager, it says that the iPhone is an "unknown device" and displays the error code 43 (windows has stopped this device because it has reported problems). According to my computer, the device has malfunctioned somehow and now will not work in any USB port on any computer in my house. In addition, he went up to this ceases to be able to charge through the outlet. I doubt it's the USB at the origin of the problem, but I am extremely frustrated and have gone through many hours trying to solve the problem without success. Help, please.

  Hello

  Welcome to the Microsoft community.

  I can understand that the windows computer is unable to recognize the iPhone 5 and when you try to check in the Device Manager it prompt the error "unknown device" with error code 43.

  This must be due to the problem with hardware drivers or a device in the system.

  The code 43 error means that Device Manager will stop a hardware device, because the material reported to Windows that is having some sort of problem not specified.

  I need some clarification from your end to refine the question.

  1. what security software is installed?

  2. don't you make changes to the computer before the show?

  3. the other recognized devices in the USB ports?

  In order to solve the problems in this regard, let us try these methods:

  Method 1. I suggest you to uninstall and reinstall the usb controllers to check the status.

  To remove and reinstall all USB controllers, follow these steps:

  1. Click Start, click Run, type sysdm.cpl in the Open box and then click OK.

  2. click on the hardware tab.

  3. click the Device Manager button.

  4. develop Bus USB controllers.

  5 right-click every device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  6. restart the computer and reinstall the USB controllers.

  7. connect the USB device and perform a test to ensure that the problem is solved.

  Method 2. Run the tool material and features.

  This built-in troubleshooting will attempt to identify the problem and then solve the problems. It checks common issues related to any installed device or hardware attached to your computer.

  1. click on Start , then click Control Panel.

  2. in the search box, type Troubleshooting, and then click Troubleshooting.

  3. under hardware and sound, click set up a device and follow the instructions on the screen.

  NOTE: If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  You can also refer to the below the Microsoft Help article:

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = WS.10) .aspx

  For more information, see the links:

  http://support.Apple.com/kb/TS1538

  http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

  Hope he can answer all your questions. If the problem persists, let us know, we will be happy to help you.

  Thank you.

• W7 Dell Inspiron N5050, disorder of generic Bluetooth adapter; "Windows has stopped this device because it has reported problems (code43).

  I'm getting generic Bluetooth adapter, "Windows has stopped this device because it has reported problems (code 43)." It shows at the beginning > Device Manager > portable computer icon, like a yellow! -in the icon of the computer. I have and you use a wireless mouse and I don't know if that is considered to be "Bluetooth" or not. I don't have any other element without wire/Bluetooth that I use. I connect to wireless internet. When I delete the device, after a reboot it comes back with the same problem. Troubleshooting found nothing to help. I did a restore to windows from the hard drive partition, (turns out was unnecessary, problem turned have been bad screen I should have caught before to do reinstall). Month? After that this problem started. I mention this to try to be through details. I would like to remove the adapter - or - change something - or - what ever? to stop it. Thanks in advance.

  Thanks, I went to the start menu > type devmgmt.msc > left click on the result > right-click on Bluetooth radio > click left adapter > click on disable /OK. Restart and the warning went and did not return. It's not all "deleted", BUT if the warning is under control, be it. Out of sight now so happy, happy, it is me. Thank you

• peripheral Bluetooth, Windows has stopped this device because it has reported problems. (Code 43)

  my bluetooth device does not work and this is the message I get:

  Windows has stopped this device because it has reported problems. (Code 43)

  Windows has stopped this device because it has reported problems. (Code 43)

  Diagnosis

  A device driver has notified the operating system that the device failed.

  Hardware devices do not work or are not detected in Windows FIX IT:

  http://support.Microsoft.com/mats/hardware_device_problems