Windows is uninstalling this device C21

Similar Questions

• Error: Code 43; Windows has stopped this device because it has reported a problem whiel trying to use Cyberlink Webcam

  Title: cannot activate cyberlink webcam

  My cyberlink webcam was working fine until today. It will not turn on. After you apply the troubleshooting suggestions, I received a reply as follows: 'windows has stopped this device because it has reported a problem. (code 43) What is - this and how to solve my problem. I have a HP Pavilion g6. Help, please!

  Hello

  -Did you do changes on the computer before this problem?
  -What is the operating system installed on your computer?
   
  The error code you get is due to one of the engines that controlling the device notified the operating system that the device has failed in some way.
  Method 1: Run the Microsoft FIXIT from the link and if the problem persists.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/mats/hardware_device_problems/en-us
   
  Method 2: Uninstall and reinstall the USB controllers
  You can try to uninstall the drivers and also scan for any hardware changes in Device Manager.
  (a) open Device Manager by clicking Start , and then type Device Manager.
  (b) expand the Controllers of Bus USB section by clicking on the '+' sign.
  (c) Uninstall each of the devices under the USB Controller section by right-clicking on each one, and then click Uninstall.
  (d) close the Device Manager and restart the computer.
  Windows RE-automatically install the USB controllers in your computer, without you having to do anything further. Your computer is now running properly USB devices.
  For reference:
  Updated a hardware driver that is not working properly
  http://windows.microsoft.com/en-us/windows-vista/Update-a-driver-for-hardware-that-isn ' t-work properly
  
  Method 3: If the problem persists, I suggest you to follow the steps from the link and check if it helps.
  Code 43: Windows has stopped this device because it has reported problems
  http://TechNet.Microsoft.com/en-us/library/cc725873 (WS.10) .aspx
   
  Hope this information helps.

• Error code 43 (Windows has stopped this device because it has reported problems) on nividia 8800 gt graphics card

  I have a computer with dual nvidia geforce 8800 gt graphics card graphics cards, but I recently started getting the following in my device manager error message: "Windows has stopped this device because it has reported problems. (Code 43) »

  I started getting this message out of the blue after moving from my computer to another room.  I knowingly did not change anything on my PC and have been released for about 2.5 years with no real problems to speak of her.  I tried to uninstall and reinstall the latest driver from nvidia and had no luck.  I don't have access to the nvidia due to the device being disabled control panel.  Also I tried to restore my PC to a previous save point with no luck as well.  A short reading on nvidia forums led me to try a registry scan and repair, but alas it was without result.

  Any advice on what could be the cause of the problem and the best solution would be greatly appreciated.

  Hi rd,.

  You could try to remove one of the cards, then update the driver.

  They should use the same driver and may be coflicting at startup.

  You should also check the power supply if it is a few years old.

  Also make sure it is off enough electricity for the installation of the split card.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error: "Windows has stopped this device because it has reported problems. (Code 43)

  Original title: chip Blue tooth

  Summer just check via the Device Manager and found my 'CSR Bluetooth Chip' has a problem: "Windows has stopped this device because it has reported problems. (Code 43)' checked the update driver and it's all good, no matter what can shed light on this problem?

  Hello Brady.

  Thanks for posting your concern to Mirosoft forum, I'll certainly help you with this problem.

  You might face this problem because damaged or obsolete Bluetooth drivers. I suggest you follow the steps below and check if it helps.

  1. Did you of recent changes to the computer before this problem?
  2. When you receive this error message?
  3. Your computer will detect the Bluetooth device?

  Please follow the methods and check the status of the issue.

  Method 1: Run the diagnostic tool

  The diagnostic tool is a tool that will check the hardware attached to the computer for all known with him of the issues and provides details and how to fix them. Follow these steps and run the troubleshooter.

  Connect the devices to the computer.

  Hardware devices do not work or are not detected in Windows

  If the problem persists, follow method 2.

  Method 2: Uninstall and reinstall the Bluetooth driver.

  Follow the steps below to uninstall the Bluetooth driver.

  1. Click Start
  2. Click on Control Panel.
  3. Go to system and security.
  4. Under System , click Device Manager.
  5. You can get driver Bluetooth and expand it.
  6. Right click on the driver Bluetooth and select Uninstall.
  7. Now, restart the computer and check the status of the Bluetooth driver.

  See also:

  Code 43: Windows has stopped this device because it has reported problems

  Devices & drivers

  Let us know if you need more assistance. We will be happy to help you.

  ____________________

  Thank you best regards &,.

  Isha Soni

• iPhone 5 Code 43 Windows has stopped this device because it has reported problems

  Then, only in the past few days windows can't recognize my iPhone when I plug it via USB, and so does not charge or sync with iTunes. When I open the Device Manager, it says that the iPhone is an "unknown device" and displays the error code 43 (windows has stopped this device because it has reported problems). According to my computer, the device has malfunctioned somehow and now will not work in any USB port on any computer in my house. In addition, he went up to this ceases to be able to charge through the outlet. I doubt it's the USB at the origin of the problem, but I am extremely frustrated and have gone through many hours trying to solve the problem without success. Help, please.

  Hello

  Welcome to the Microsoft community.

  I can understand that the windows computer is unable to recognize the iPhone 5 and when you try to check in the Device Manager it prompt the error "unknown device" with error code 43.

  This must be due to the problem with hardware drivers or a device in the system.

  The code 43 error means that Device Manager will stop a hardware device, because the material reported to Windows that is having some sort of problem not specified.

  I need some clarification from your end to refine the question.

  1. what security software is installed?

  2. don't you make changes to the computer before the show?

  3. the other recognized devices in the USB ports?

  In order to solve the problems in this regard, let us try these methods:

  Method 1. I suggest you to uninstall and reinstall the usb controllers to check the status.

  To remove and reinstall all USB controllers, follow these steps:

  1. Click Start, click Run, type sysdm.cpl in the Open box and then click OK.

  2. click on the hardware tab.

  3. click the Device Manager button.

  4. develop Bus USB controllers.

  5 right-click every device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  6. restart the computer and reinstall the USB controllers.

  7. connect the USB device and perform a test to ensure that the problem is solved.

  Method 2. Run the tool material and features.

  This built-in troubleshooting will attempt to identify the problem and then solve the problems. It checks common issues related to any installed device or hardware attached to your computer.

  1. click on Start , then click Control Panel.

  2. in the search box, type Troubleshooting, and then click Troubleshooting.

  3. under hardware and sound, click set up a device and follow the instructions on the screen.

  NOTE: If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  You can also refer to the below the Microsoft Help article:

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = WS.10) .aspx

  For more information, see the links:

  http://support.Apple.com/kb/TS1538

  http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

  Hope he can answer all your questions. If the problem persists, let us know, we will be happy to help you.

  Thank you.

• AMD Radeon HD: Windows has stopped this device because it has reported problems. (Code 43)

  In my device manager, in graphics cards, for my AMD Radeon 7500,7600 M graphics card in the series, the properties display the following error message:
  "Windows has stopped this device because it has reported problems. (Code 43) »

  I uninstalled the drivers and reinstalled them - it's the 12.104.0.0 version, which I have confirmed is the last. I have the Catalyst Control Center installed as well.

  Can someone help me understand this error? Why would he stop? What would be my next steps to try to solve it?

  See you soon,.

  Sam

  Hi thanks for trying, but the Dell drivers are those which deal with the problem of restart.

  I find the most recent driver Intel HD 4000 (Win64_15313_intel) and installed version, then I installed the latest drivers AMD (13-4_mobility_win7_win8_64_dd_ccc_whql_AMD) on the site of AMD. This solved my problems and my graphics card works fine now.

  So yes, just repeat those it tells me to install when I get my serial number and OS (Windows 7) were:

  Intel: 5423_Video_Driver_T6XGJ_WN_8.15.10.2669_A02

  AMD: 5423_Video_Driver_VGR24_WN_8.951.9.0_A02

  And these caused problems without end - the graphics card would not work, and then when I installed drivers from AMD, Dell, it would cause my system to reboot every 2 or 3 minutes. It looked like some kind of incompatibility between the two graphics cards and the drivers provided.

  The other representative of Dell told me the same thing that you - so I wanted to post my solution in case anyone else has this problem.

• Windows is uninstalling the device. Code 21. Device_IPod

  Original title:

  Device_IPod

  Using Windows 7.  I am able to install my ipod, but it disappears as soon as I click on it.  In my devices & printer folder, is to show a problem with the ipod.  Universal Serial Bus controllers.  When I click it, the message is that windows is uninstalling the device.  Code 21.  Why this is happening and what settings should I change.  Device is connected to Port_ #0003.Hub_ #0008.

  Hello

  Code 21

  Windows removes this device. (Code 21)

  Recommended resolution

  This error means that Windows is trying to remove the device. However, the device has not yet been completely deleted. Here are some things you can try to solve this problem.

  • Wait a few seconds and press the F5 key to refresh the display of the Device Manager .
  • If this does not resolve the problem, restart your computer. Click Start, click shut down, and then select restart in the Shut down Windows dialog box to restart the computer.

  You can try to uninstall the iPod from the Device Manager, restart the computer, and connect the iPod. It should automatically detect and install the drivers for it. Check if it works.

  If the steps above fail, please contact the Apple support team for help.

  It will be useful.

• Unknown device: Windows has stopped this device because it has reported problems (Code 43).

  I have Windows 7 Ultimate. Recently an unknown device keeps popping up in the device manager every time that I start to win. It is reported the location is in the front USB hub, but I haven't changed it anything lately. The device status says "Windows has stopped this device because it has reported problems (Code 43)". I can uninstall or disable it but it will get picked up again the next time that I reboot. All other usb devices (mouse, keyboard, webcam, UPS APC, external hard drive, printer) work very well. How can I get rid of this nuisance so that it is not reappear?

  If the problem coincided with connecting the inverter APC that may indicate the problem is with the inverter.

  Somewhat similar situation discussed in the following link:

  http://www.velocityreviews.com/forums/t527369-APC-ups-USB-as-unknown-device.html

  Your situation sounds similar as "Information system" leading the 'problem of the device' has an error Code "this device is working properly" but still "unknown device".

  I would say to detach from the APC UPS of the computer and uninstall any software related.

  Restart the computer and see if the "Unknown device" problem resolves.

• Transcend storage device when connected gives error "Windows has stopped this device because it has reported problems. (Code 43) »

  Original title: Windows has stopped this device because it has reported problems. (Code 43) ».

  Hi, I have a storage device 'Transcend', but when I connect it it gives me "Windows has stopped this device because it has reported problems. (Code 43) »

  . in the last ididnt have had problems with this unit. what I can do.

  Shirly

  Hello

  1. What is the brand and model of the device of Transcend storage?

  2. other USB devices work on your computer?

  Error code 43 indicates that one of the motors controlling the unit notified the operating system that the device failed in some way.

  Method 1:

  Step 1:

  I suggest you try plug the storage device Transcend to another computer and check if it works.

  Step 2:

  Also, try to connect the Transcend storage device on another USB port and check if it's work (which you know are working perfectly).

  Method 2:

  You can run the diagnostic Fixit tool. Check out the following link.

  Hardware devices do not work or are not detected in Windows http://support.Microsoft.com/mats/hardware_device_problems/

  Method 3:

  You can check after uninstalling and reinstalling the USB controller. Follow the steps.

  (a) click Start and then click Control Panel.

  (b) click System and Maintenance, click System, and then click Device Manager.

  Note: If Control Panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  (c) in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  (d) repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Reference:

  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
  Note: the information provided in the article mentioned above are applicable to Windows 7 too.

  Method 4:

  You can try to install the latest drivers for the storage device Transcend on the manufacturing site and check if it helps. Check out the following link.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  See also:

  Install a USB device

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  Code 43: Windows has stopped this device because it has reported problems

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = ws.10) .aspx

  It will be useful.

• Error "Windows has stopped this device because it has reported problems. (Code 43) "when I try to plug my mouse optical usb into the USB port.

  Original title:

  First here is my card http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02479651&cc=ca&dlc=en&lang=en&lc=en&product=4299342 desktop pc
  and my mobo card http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02560084&tmp_task=prodinfoCategory&cc=ca&dlc=en&lang=en&lc=en&product=4299342
  (running windows 7 x 64 and not changed all my pc hardware so everything on the Web page is true)

  in any case, when I try to plug my mouse optical usb in the port of e/s (usb port) on the front panel (which supports usb 2.0) a notification pops up saying
  "one of the usb devices attached to this computer has malfunctioned and windows does not recognize it. Help to solve this problem, click this message. "
  so I click it and and called up pop-up windows
  "the usb device not recognize."
  display 1 unknown device. Link to the image: http://img38.imageshack.us/img38/3579/usbdevicenotrecognizewi.jpg
  Then I double click on it, next pop up another window called "unknown device properties" and under "device status", he said:
  "Windows has stopped this device because it has reported problems. (Code 43) »
  Link to the image: http://img204.imageshack.us/img204/8597/unknowndeviceproperties.jpg

  Also the same things happen when I plug in usb, keyboard , but not when I plug a flashdrive usb 2.0 without notification or anything pop up.

  Here's what I'm trying to fix it but ended up with saying it was installing the device, installation failed and getting the error failed and unrecognized again...

  • Plug my optical mouse on my other ports and it works perfectly fine (to see if its working)
  • Plug the mouse (in the wrong port), went to Device Manager and uninstall the unknown device, reboot with usb plug in and have the connection to the internet (not decided)
  • Uninstall all devices under USB bus controllers in the Manager device and rebooted with mouse in internet connection (not decided)
  • Went to device manager expanded bus controllers USB right-click on power management all the device label "usb root hub" click and uncheck the box "allow the computer to turn off this device to save power" and reboot (do not set)
  • Open the normal startup in msconfig (system configuration) selected and restarted (did not set)
  • Shut down the computer, disconnect the plug, unplug all the devices connected to all IO ports (usb port specifically) and my desktop pc has left alone for an hour and a half and start it to the top after with everything back plug (mouse in the wrong port) (has not set)

  Note: when the mouse is connected to the usb port it is light on substance, but its does not (not flashing do not and when you move, mouse is frozen on the monitor)

  Hello

  The results highlight the drivers. It is best you contact HP support and get all the latest device drivers.

  http://WWW8.HP.com/ca/en/support-drivers.html

• Windows has stopped this device because it has reported problems. (Code 43) Card problem Nvidia GT540m Grphics in Dell XPS 15

  Windows has stopped this device because it has reported problems. (Code 43)

  I have a Dell xps laptop l502x and his entry up with error code 43 in the nvidia gt540m in Device Manager. I tried to uninstall and then reinstall the drivers for it but it didn't work, again I tried with the restoration of the system and backup system too but nothing could fix the problem. whenever I try to open up the Nvidia control center a popup comes up saying "the NVIDIA display settings not available" Please help me my email - :) * address email is removed from the privacy *.
  All this stuff happened only after windows update in the afternoon and at night when I started my system it happened :/ HELP PLEASE

  You did the mistake of using windows update for drivers?

  Visit Dell support, specific to your tag # and update drivers

• Port_ #0003.Hub_ #0005, Windows has stopped this device because it has reported problems. (Code 43)

  my computer did not recognize my usb to the printer device.

  Hello

  1. what operating system is installed on the computer?

  2. this printer was working on the computer before?

  3. have you made changes on the computer recently?

  4. What is the brand and model of the computer?

  5. What is the brand and model of the printer?

  Try the following steps.

  Method 1.

  Connect the printer on another computer and check if the printer works fine.

  Plug another usb printer and check if the printer works fine on this computer.

  Open the hardware and devices Troubleshooter: http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2.

  I also suggest you follow the steps in this article.

  Install a USB device: http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  Printer in Windows problems: http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Refer.

  Code 43: Windows has stopped this device because it has reported problems: http://TechNet.Microsoft.com/en-us/library/cc725873%28V=WS.10%29.aspx

  I hope this helps.

• Error "Windows has stopped this device because it has reported problems (code 43)" after the computer start in low resolution and remains after the connection

  Original title:

  Problem occurs intermittently, but almost every time at the first start the morning. The problem can be seen during the POST and the rest after logon. After several reboots, he can come good, but at the next restart could be bad. One clue is that the Device Manager said that to display card NVIDIA Ge Force 8400 GS that "Windows has stopped this device because it has reported problems (code 43)." Driver update says I have the latest driver insalled, version 8.17.12.9573. Help, please

  Have you tried to update your BIOS? Are there updates the firmware for your video card?

• Windows has stopped this device because it has reported problems. Toshiba R830 (code 43)

  my show toshiba r830 Windows has stopped this device because it has reported problems. (Code 43)

  Windows has stopped this device because it has reported problems. (Code 43)
   
  Diagnosis
  A device driver has notified the operating system that the device failed.

  Resolution

  Hardware devices do not work or are not detected in Windows FIX IT:

  http://support.Microsoft.com/mats/hardware_device_problems

• W7 Dell Inspiron N5050, disorder of generic Bluetooth adapter; "Windows has stopped this device because it has reported problems (code43).

  I'm getting generic Bluetooth adapter, "Windows has stopped this device because it has reported problems (code 43)." It shows at the beginning > Device Manager > portable computer icon, like a yellow! -in the icon of the computer. I have and you use a wireless mouse and I don't know if that is considered to be "Bluetooth" or not. I don't have any other element without wire/Bluetooth that I use. I connect to wireless internet. When I delete the device, after a reboot it comes back with the same problem. Troubleshooting found nothing to help. I did a restore to windows from the hard drive partition, (turns out was unnecessary, problem turned have been bad screen I should have caught before to do reinstall). Month? After that this problem started. I mention this to try to be through details. I would like to remove the adapter - or - change something - or - what ever? to stop it. Thanks in advance.

  Thanks, I went to the start menu > type devmgmt.msc > left click on the result > right-click on Bluetooth radio > click left adapter > click on disable /OK. Restart and the warning went and did not return. It's not all "deleted", BUT if the warning is under control, be it. Out of sight now so happy, happy, it is me. Thank you