Windows not mark the ad hoc network.

Similar Questions

• 'Windows not will mark the Ad Hoc network'

  Hello

  User of the computer without experience here.  I have an iPad that works very well if I have WiFi available.  I don't have WiFi at work, so I am interested in the connection through my work Windows 7 computer, which is connected via a connection to the local network.

  I did everything according to the instructions on:

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network

  However, when I put my key name and the network security and press 'Next', I get the message, "Windows could not configure [network name]."

  There is no other error message and no indication on what I could do so that Windows is able to put in place the ad hoc network.

  What should I do?

  Thank you

  Rob

  Hello Rob,

  Thank you for the update.

  As you said that the computer is connected to a domain network, I would like to advice post you your query in the TechNet forums because they have more expertise on these issues. Follow the link below to do the same.

  Forums TechNet for Windows 7
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Hope this information helps.

• DeskJet 3070 unable to connect to the ad hoc network

  Hello

  I'll put up my new HP Deskjet 3070. This printer has wireless capability. I would use it wireless with my laptop Macbook Pro (OSX 10.6.8).

  I don't have a wifi network or router at home. That's why I created a wifi (one to one) on my mobile ad - hoc network, named MyPrinterNetwork. This is the type of network used to connect a computer to the other on wifi. MyPrinterNetwork is then visible to other devices compatible wifi (other computers, smartphone,...), and devices can connect to the network (and share files or Internet by wifi). This thread http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/Connect-Deskjet-3070A-wirelessly-to-my... suggests that this printer is able to connect to ad hoc networks.

  I then launch the HP utility to configure the printer. But when the screen appears with the list of available wifi networks, MyPrinterNetwork is not in the list. The list contains only the other wifi available through networks points (values in wifi mode column are all infrastructure) access. If I try to enter the name of a network manually, the software indicates that the printer cannot see or connect to this network.

  Executive Summary:

  -Someone would confirm that the printer Deskjet 3070 is able to connect to the ad-hoc wifi networks?

  -If so, why my adhoc network isn't in the list in the configuration utility?

  Thanks and greetings

  Johnny

  Hello Johnny.

  Deskjet 3070 Network Infrastructure support only, it does not support the ad-hoc connection.

  As you can find in the user manual:

  Traditional wireless connection (requires router)
  
  To connect the HP All-in-One to an integrated wireless WLAN 802.11 network, you will need the following:
  
  - A wireless 802.11b/g/n network that includes a wireless router or access point.
  NOTE: 802.11n will only support 2.4Ghz
  
   A desktop computer or laptop with either wireless networking support, or a network interface card (NIC). The computer must be connected to the wireless network that you intend to install the HP All-in-One on. 
  
  Page 33:http://h10032.www1.hp.com/ctg/Manual/c02887357.pdf
  

  As an alternative, try feature that allows the mac to act as a router in Mac OS X internet sharing Infrastructure mode:

  http://docs.info.Apple.com/article.html?path=Mac/10.7/en/mchlp1540.html

  A limitation, you should be aware, the Internet sharing security supports WEP in shared only authentication mode that is not supported by the printer you can find below:

  http://support.HP.com/us-en/document/c02871178

  Therefore, you should keep sharing without security password in order to connect the printer to the network.

  It will be useful,

  Shlomi

• Does not mark the emails as unread - iOS 9.3 and Exchange account

  Hello

  It drives me crazy! I'm an iPhone user for many years since the first iPhone.

  I use the mail with exchange account application.

  Given that I have updated to iOS 9.3 I does not mark the emails as unread after they are read.

  The status "unread" is constantly reset to 'read '.

  I lose emails because of it!

  Who can help on this?

  Thank you

  Oded

  This isn't the behavior that I'm observing.

  Have you tried a simple Reset by pressing the Home and Power buttons until the Apple logo appears.

• How can I check my sites marked in the main window, not on the sidebar

  I have all my addresses marked with a bookmark in the bookmarks menu, but they open in the sidebar not on the home page. I can change that.

  Hello

  Try: Button Firefox-> Bookmarks-> show all bookmarks

  (if you have the menu bar (i.e. File, Edit etc) at the top left to try: bookmarks-> show all bookmarks)

  This will not open them in a tab, but in a new window.

  Jack

• Unable to connect to the ad hoc network created in windows vista

  Hello

  I created an ad hoc network on the laptop to my sister that is running windows Vista Home Basic Edition x 86.
  I installed ubuntu 11.04 alongside windows 7 on my laptop. I can find the network under ubuntu, but I can't connect to it.
  Can someone help me with this please?

  Hello

  Method 1:
  You can networks troubleshooting wireless with Ubuntu and check:
  https://help.Ubuntu.com/community/WifiDocs/WirelessTroubleShootingGuide

  Method 2:
  If you have problems with Windows networks and then check out the link
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Install HP does not see the printer in network, Windows DOES. Help!

  Hello

  I am trying to add my HP Officejet k8600dn to Windows 7 (32 bit) so I can scan, but the HP Installer (add device) can not see the printer. The unit is set up by cable to a switch on my network via an ethernet cable. If I go into the menu "Add a printer" Windows, I can install the printer very well. But I have to be able to scan and I don't know what to do.

  Tips on getting functional analysis if the HP software is unable to see my printer? Subnet mask and gateway on the printer are the same for the computer and the printer. I typed the correct IP address in the "Add a device" menu of HP, but he sees not just it. ARRGG!

  Thanks for any help!

  Hello

  I think that there is some confusion because the Officejet k8600dn is only a printer, it is not a multifunction device and does not provide the capability of scanning.

  You can find the specifications below:

  http://support.HP.com/us-en/document/c01287217

  If you have any different model printer, please specify the exact model.

  Kind regards

  Shlomi

• Windows 7 does not see the xp on network machines

  We are a store Dell running XP Pro on peer-to-peer networks... deployment of Windows 7 Pro workstations and laptops. Out-of-the-box, we put it sharing, discovery, working group; etc. However, some of the machines Win 7 do not see network XP machines and thus cannot use the graphical interface to map to different files and resources. You can their ping, set using "Net Use" or "Add a network location" or "Connect Player" as long as you know the complete path (ie: \\server\server_share\home\bill\cad\cnc.) But you can't see them in the network window to map the drive to records letters. I have studied this issue, has visited many forums and talked to many other tech all with the same question. The conclusion seems to be because it is a Win 7 problem not addressed XP came out. So the current thinking seems to be to use the commands Net use in an autoexec.bat file. So to use the latest version of Windows with XP, we need to use commands BACK maps automatically records. A huge advances in technology. Really? Tell us we're wrong and there is an answer?

  Hello

  Your question of Windows7 is better suited in the TechNet forums. Please post your question in the TechNet forums.
  You can post your request here on TechNet community that focuses on issues such as
  http://social.technet.Microsoft.com/forums/en/categories

  I hope this helps.

• Transmission of data via the Ad Hoc network in LabVIEW

  Hello

  I'm trying to transmit some data (position, speed, etc.) a laptop computer to a host computer.

  The laptop and desktop have the card installed wireless so I thought this would be a good

  the idea of transmitting data via Wi - Fi using TCP.

  However, the problem is that there is no router/modem in the area where the laptop is sitting

  so, I create a network of Ad-hoc (computer to computer) between the laptop and the desktop computer.

  Then, I use "ipconfig/all" in the Windows command prompt to extract the IP as follows.

  IP address wireless laptop: 169.254.165.72

  IP address Wireless Desktop: 169.254.102.126

  Desktop Ethernet IP address: 129.94.229.230

  I then use the code example in the TCP library named 'Data Server.vi' and "Data Client.vi."

  I listen on port 6340 times the wireless and ethernet desktop on the side map server.

  And on the side of the customer, I opened a connection to port 6340 169.254.102.126 IP address.

  However, the connection cannot be granted. Anyone know why this is the case?

  Note: I have disabled all firewalls.

  Interesting, when 2 computers are connected to the same modem, their IP addresses

  differ only by the last number (e.g. XXX.XXX. XXX.123 vs XXX.XXX. XXX.256), but when an ad

  the House of Commons network is established, their IP addresses have 2 numbers that are different. (XXX.XXX.

  102,126 vs XXX. XXX.165.72) I wonder if this has nothing to do with the failure.

  Thanks for all your help.

  Ron Liou

  I somehow this job.

  What I've done

  -Once again set up an Ad hoc network for the labtop and Office

  -verification of the IP address is always the same

  > Portable wireless IP address: 169.254.165.72

  > Portable wireless subnet mask: 255.255.0.0

  > Wireless Office IP address: 169.254.102.126

  > Wireless Office subnet mask: 255.255.0.0

  -switch on the ICS of the ethernet on the desktop card

  (This resulted in an IP different addresses assigned beng)

  > Portable wireless IP address: 192.168.137.21

  > Portable wireless Subnet Mask: 255.255.255.0

  > Wireless Office IP address: 192.168.137.1

  > Office Wireless Subnet Mask: 255.255.255.0

  Now I use the ip address of office (192.168.137.1) to open the connection

  and it works! ??

  I am very pleased with the fact that it works but I would like to have one

  explanation on why it takes an ICS.

  Thank you!

• Computer sharing internet with mobile phones on the ad - hoc network

  Original title: ad hoc internet sharing network

  I have only 1 computer at home and 2 mobile phones. My wireless router doesn't work so I can't get access to the internet through a wired connection to my laptop. I wanted to share the internet access from my laptop to 2 mobile devices, but I do not know how to do it. I tried to create an ad hoc network by following instructional videos online, but they do not seem to work for me. I have a laptop Samsung Windows 7 Professional. Any thoughts?

  Hello Mann,

  The manual configuration of ad hoc steps network has really worked for me. I don't really know how much I missed. For my curiosity, I tried to open the link provided by Ramesh above and found some interesting things. I downloaded a software called the virtual router on the site - http://virtualrouter.codeplex.com/. In fact, it has worked for me and made my life so much easier. I just have a good concern, is this completely harmless software for my computer? I have not any refusal of Microsoft Security Essentials of any kind in any case. :)

  Please notify.

  Thanks for your help!

  JM

• RALink RT3290 does not "see" the 5 GHz networks (802.11n)

  I just bought a HP Pavilion 17 Notebook PC (number of product F9M00UAR #ABA) with victory 8.1 x 64 installed and the wireless card does not 'see' any 802.11n networks.  The driver installed is 5.0.37.0 with a date of 25/11/2013.

  I've seen problems with upgrades to 8.1 affecting the adapter, but nothing works not properly out of the box on a new machine from 8.1 to WIN.  Can anyone offer any suggestions on how to force it to see 802.11n?

  Thank you

  Mark

  Hello:

  The WLAN RT3290 card is only a single band (2.4 GHz).  He can not find the 5.0 GHz band.

  Whenever you see a suffix of bgn on a description of the wireless card, it means that it is a map only single band (2.4 GHz).

  Cards N whose suffixes ending with abgn or agn wireless dual band (2.4 GHz/5.0 GHz).

• Windows 7 - why the priority of network adapter is ignored when you are connected to the area on a lower priority NIC?

  I have two network cards installed on my laptop.  I wanted to test and see how Windows 7 Ultimate managed the priority of the network adapters so I connected to a small Internet (NIC B) router, and the other on my domain (NIC A).
  First of all, it was a pain to find network adapter priority.  After some research and fun Google I found this.  Unfortunately, the search bar has not helped.
  Control Panel-> network and Internet-> view network status and tasks-> to modify the adapter-> Hold down 'alt' to bring up the menu "File"-> select 'Advanced'-> select 'Advanced settings' in the menu drop-down-> adjust your priorities of the adapter in the 'Advanced settings' window, under the tab "maps and links.

  With "B NIC", defined as the highest priority, I tried to browse the internet.  It was impossible to travel.  Then I disabled 'NIC A' (the NIC domain) and I can browse the internet.  Windows XP he handled this much better.

  Select 'NIC A', and then check 'NIC B' is the highest priority.  Then try tracert on www.google.com.  It refreshes my domain as the first hop router.  It seems to be completely ignoring 'NIC B', unless I have disable 'NIC A' completely.

  In case someone of another Vienna here, looking for the answer to this, as I did, I thought that putting the real solution to this question.  Many web pages say to change the priority of going on network connections and change the order there to what you like.  You don't have to bother with this setting.

  It does not work. He has apparently no effect on the use of connections.

  What Windows actually uses is the metric value for network connections.  The lowest metric value is tried first.  In my case, I have a connection broadband shabby home, but I can attach wireless on my phone for occasional good bandwidth.  So, I want to always use the connected wireless and ignore the wired connection, but still the chance to printers and other things on my network cable at the same time.  I want to keep both on and not to disable the wired when I use my phone.

  To resolve this problem for real, go to and right click your Wi-wired adapters and one at a time to change the properties.  Select IPv4, click and then .  For each of them, disable the "Automatic metric" checkbox and set the metric value manually.  I put the wireless cable and 1-2, which gave me the behavior I wanted.

  The Automatic metric is defined by Windows based on the speed of connection and a wired connection is generally faster than a wireless one.

• 8.1 Windows not in the store after discount

  I recently bought a HP Envy 800-060 with Windows 8, which I upgraded to 8.1. Yesterday, something happened which caused the computer not to be unable to start successfully, and I had to perform a system refresh. Apart from the inconvenience of having to reload the software, settings, etc., the restored system Windows 8, but the Windows 8.1 upgrade is not found in the store. The HP Wizard is no help on this, and when I went to the Microsoft website to try and download the upgrade from there, it just hit me back to the store. I guess somehow the Bank thinks that I've already updated, so it doesn't let me do it again. Any ideas how to solve this problem?

  Hello

  Probably you are missing some required components upgrade patches.  However, there are other conditions that could cause the same problem.  See the link below.

  Why I can't update in the store?

• Windows not reformatted the diskette.

  Hi, ive been having this problem for a long time now, I can't get windows xp to FORMAT floppies! I can read and write but do not format, Ive tried to do in the box cmd, in safe mode, I tried to change my config.sys of little help I found on microsoft support. I'm confused and I really need to get these drivers on this disk, so I can install sata on my other computer :( I have a dell dimension 8400 Windows XP Home Edition. Also when I try to format it in the cmd box it tell me "Invalid Media or track 0 bad".

  Yes, everything is properly connected and it does not be able to run at him...

  Hello Jmitchell6799,

  Thank you for your message.  Have you tried to perform a format of the Explorer window?  Try the following steps:
  Click 'Start' > click 'my computer '.
  Click the drive you want to format and select "Format".
  Did you format your drive?
  We can't wait to hear back on your part.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• I'm trying to set up an Ad Hoc network, but there is no option for the Ad Hoc network configuration when I go into the network and sharing Center.

  I looked at how to make a point of my computer because I have a usb wireless internet device for my laptop and I tried to get an ad hoc network setup but there is NO option for the CONFIGURATION of the NETWORK AD HOC when I go to network and sharing Center... what should I do?

  original title: ad hoc isn't here...

  Hi NickBean2,

  You can refer to the following articles and see if it helps.

  Set up a computer-to-computer (ad hoc) network
  Solve problems, find wireless networks

  Hope this information is useful.