Windows will not be updated 360 controller driver

Similar Questions

• My windows will not recognize my CD/DVD drive

  My computer crashed recently and since then windows will not recognize my CD/DVD drive. My removable disk (e :)) is there, but I was told that windows cannot access the disk.) Also when I try to eject a developed error warning.

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP - Windows Expert - consumer: bike - Mark Twain said it right.

• Windows will not see my DVD/CD drive

  I have Windows Xp Professional SP3. Windows will not see my DVD +-RW which is internal drive, or my double-sided external DVD RW lightscribe. I tried the FixIt tool and the registry hack. They can work at the same time, but whenever I try to use the car, they both disappear again. Anyone have any new ideas?

  Hello

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  ·        What registry hack you speak and what patch did you use?

  Method 1:

  I suggest you try the steps mentioned in the articles below and let us know your progress.

  Drive CD - R or CD - RW Drive is not recognized as a recordable device

  http://support.Microsoft.com/kb/316529

  Advanced Troubleshooting for issues that occur when you are installing a new CD or DVD drive in Windows XP

  http://support.Microsoft.com/kb/314096

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  Method 2:

  I suggest to update the firmware of the CD/DVD drive on the system and check if the problem persists.

  Method 3:

  In addition, run the fix that is present in the link mentioned below.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Windows will not be updated vista, error code 8007010 error help 643.__please b!

  Windows will not update

  eddyboylip,
  If you are still having this problem then you might be able to do both of the following:

  Disk error checking

  System File Checker

  If the System File Checker corrects some problems then try the updates again. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows will not install on the new drive for HP Pavilion Elite m9510f

  I have a HP Pavilion Elite m9510f operation with Windows Vista Home Premium 64 - bit SP1 and with a Seagate Barracuda 7200.11 HDD of 750 GB.

  The HARD drive broke down a few weeks ago and is unrecoverable.

  I bought Seagate 1 TB hard drive to replace the 750Go again and used the HP recovery discs provided by HP to wipe the disk and reinstall Windows on it.

  I can run all the recovery discs 3 without problem, the computer goes through its paces to reinstall Windows and all of a sudden, the computer stops and I get the message "installing Windows could not configure Windows to run on a hardware on this computer."

  What is happening with this?  I use a HARD drive with recovery disks provided by HP.

  HARD drive replacement need to be 750Go like the original?

  Any help would be appreciated

  Probably a problem with the hard drive being the new type of AF. Windows 7 with SP1 should work better than Vista... but your Vista key will not work with ISO download linked above.

• Envy 17 j120na: 10 Windows will not start because of the driver installation failed

  History:

  I have a computer laptop j120na Envy 17 that came with windows 8.1.

  I did the free upgride for windows 10 the 18th of this month with success, but because I was not able to decrease or increase the brightness of my computer, or put it to sleep, I realized that I still had to download/update drivers. First I updated the driver GeForce since my SWsetup folder but for the other, I searched online for her, then I saw the driver download progress bar but no progress has been made. I closed the dialog close and there you go, laptop does not start, I just saw a spark between the mouse pointer and the circular blue contraption. Sometimes he shows me a BSOD with lock core auto boost with irql higher acquisition.

  Question:

  Is this a problem with the driver installation? And if so, how do I return it?

  P.s: System Restore is not an option, I restore point.

  Hi there @Aj1baba,

  Thank you for joining the Forums HP's Support and welcome! It is a great place to ask questions, find solutions and assistance of HP and the community! I read your post on the Forums of HP Support. I wanted to join you and help! I understand that you are receiving an error message that says "acquisition of lock core auto boost with irql high ' on your HP ENVY 17-j120na Notebook PC.

  The question could be deemed to occur by downloading the update. It is difficult to say at this stage. As to return to it, your best bet would have been the restoration of the system, but you mentioned only that a system restore does not work because you do not have restore points.

  Have you tried to go into Safe Mode?

  You have media or recovery disk?

  Have you tried to do a Reset BIOS?

  Have you tried perform a hard reset?

  You have beep codes or flashing LEDs?

  Please ensure that all Bluetooth device that you use with the laptop is disabled (including mobile phone).

  Please note: delete all USB/Bluetooth devices. Disconnect all devices of non-essential, as these can cause some problems.

  You can update all your drivers by going to the Web site the driver HP or by using the HP Support Assistant. If you enter Safe Mode, I suggest trying to erase the driver that you have downloaded your downloads (or the folder that you saved it in), so I suggest to make updates using updates of Windows or HP Support Assistant for now.

  Please let me know if I answered your question by clicking the "Thumbs up" if the troubleshooting in this post steps solves the problem for you please click on the button "Accept as Solution" . This will allow to the others is that present the same problem a solution also. If you need assistance, I would be more than happy to continue to help you. Please just re-post with the results of the resolution of the problems.

  Have a great day!

• Windows will not install updates after "update definition for windows defender-KB915597(Definition 1.21.1279.0) 03/03/09 '"

  Since I installed the updated definition for windows defender-KB915597(Definition 1.21.1279.0) 03/03/09, I was not able to install the new updates. I don't know why, but none of the updates I have been install, or at least try, are installation and saying "Success" next to them. I've used different methods to dispose of everything, if I have any, virus and still have not seen any progress. And unfortunately, I deleted all my restore points to keep the memory on my laptop. I have too many errors, report them all, but some of the things I did to check to ensure that I have no viruses do analyses of the complete system and remove a mysterious software they gave me an alert by (using McAfee Security). Any help will be considered. Help, please! :(

  If you install the hidden recovery partition to do the cleaning, you will probably not the product key. Otherwise, use one on the sticker attached to the computer. ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• my windows will not install updates - why?

  Setup does not work. whenever I power off, the computer attempts to install the updates, but nothing ever happens. one night, I let it run all night and still says 1 installation of 18. What is happening and how to fix it?

  Hello

  I suggest you follow these methods and see if it helps:

  Method 1:

  Try to install the update to the clean boot and check if it helps.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135/en-us

  Note: Don't forget to start your machine in normal mode by following step 7 of the link.

   

  Method 2:

  You can try temporarily turning on all security software and then try the updates again.

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  
  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

   

  Method 3:

  I suggest you to reset the Windows Update components and check.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

   

  Method 4:

  Follow the steps in the following article and see if it helps.

  Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2 http://support.Microsoft.com/kb/2509997

  Important: When running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area so all available data on this risk to be lost

  See also:

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

  Method 5:

  Check the State of Windows Installer and installer of Modules of Windows.

  a. Click Start and type Services.msc and press ENTER.

  b. Locate the Windows Installer Service.

  c. double-click on it to check if the service is started or not.

  d. change the startup type to automatic and Start the service.

  e. check the same thing for Windows Installer of Module service.

  f. Press ok and close the Services window.

• Windows will not be updated.

  Hey guys so I have a custom computer, I downloaded windows 7sp1 as a starter for the work of the computer.  Some updates have been made, but after these a few TI stopped automatically search and when asked if you will seek for hours to come is not with no result then either gel or blue screening. I tried I tried everything what Microsoft can offer services of troubleshooting, my windows is a legitimate copy, it has been accepted by windows, so I don't know what I can do... A person can offer help please.

  If please see this thread and follow the instructions exactly.

  Windows Update solution

• Windows will not activate after the hard drive is replaced on Windows 7 Home Premium.

  Recently, I had a hard drive crash and had to replace my hard drive. I took it to a computer to fix store, and they have installed and gave me a new drive for windows 7 Home premium. However, it was not approved, and I have no key validation. How can I validate windows now?

  Search for your key on the side of an office or downstairs (sometimes inside the battery case) of a laptop.

  How to activate Windows 7 or Vista manually (activate by phone)
  http://support.Microsoft.com/kb/950929/en-us

  1) click Start and in the search for box type: slui.exe 4
  (2) press the ENTER"" key.
  (3) select your "country" in the list.
  (4) choose the option "activate phone".
  (5) stay on the phone * do not select/press any option * and wait for a person to help you.
  (6) clearly explain your problem to the support person.
  (7) the person must give you a confirmation ID, copy it down on paper,
  (8) check that the ID is correct in reading the support person.
  (9) to enter the ID number, then click 'Next' to complete the activation process.

  ----------------------------  Alternatives -------------------------------------

  To enable the use of the phone
  1. open Activation of Windows by clicking on the Start button, right click on computer, clicking Properties.
  then by clicking on activate Windows now. ?

  2. click on show me other ways to activate.

  3 type your Windows 7 product key, and then click Next.

  4. click on use the automated telephone and then click Next.
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  5. click on the location nearest you from the drop-down list, and then click Next.

  6. call one of the available phone numbers listed. An automated system will guide you through the activation process.

  7. When prompted, enter the installation ID that is listed on your screen in your phone keypad.

  8 Note the confirmation ID the phone system gives you.

  9. under the terms of step 3, type the confirmation ID in the space provided, click Next, and then follow the instructions.

  10. If the activation is not successful, stay on the line to be transferred to a product activation agent who can help you.

  Microsoft Activation centers worldwide telephone numbers:
  http://www.Microsoft.com/licensing/existing-customers/activation-centers.aspx
  (This site is for activating Volume License, but if you call, they will help you)

  The phone number is not working:
  Microsoft Wordwide contacts: http://www.microsoft.com/worldwide/default.aspx

  Register Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/help/register
  Register Windows 7 and you automatically receive a series of three welcome to Windows e-mails
  filled with tips, creative tips and other information to you help get the most out of Windows 7.
  You also get a subscription to the monthly newsletter of Windows Explorer,
  where you will find other tips and tricks, as well as special offers.

  Activation and registration of a Microsoft product
  http://support.Microsoft.com/?kbid=326851
  Windows activation: (888) 571-2048

  Learn about Activation:
  http://TechNet.Microsoft.com/en-us/library/ff793423.aspx

  J W Stuart: http://www.pagestart.com

• Installed Windows 7. Windows will not be updated.

  Hello

  Long story short I'm install Windows on my new SSD. everything went to the wonder. Anti-virus software installed, all saved and updated all existing programs currently.

  So, I'm going to update windows. Keep checking for screen updates loading. I leave all night. always the same in the morning. I tried a number of things, including the Microsoft fixit program, install Windows Update standalone (two different versions published by microsoft), and windows diagnostic update.

  When I use Windows Update Diognostic, he says:

  Found promblems

  Windows Update error 0x8024402c(2016-06-23-T-12_02_41P) not fixed

  Other issues that have been resolved.

  I ran the Diognostic again to retrieve detailed information, but he came to the top has set. update still does not.

  You might look into this it's the new way to update after a clean install.

  https://blogs.technet.Microsoft.com/windowsitpro/2016/05/17/simplifying-updates-for-Windows-7-and-8-1/

  It is expected by M$, we must now jump through hoops to clean install.

  It is older but still works,

  http://www.ZDNet.com/article/sticking-with-Windows-7-the-forecast-calls-for-pain/

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-update/Windows-Update-remains-at-checking-for-updates/ff3c442e-79a6-40d3-AC35-29e130cebef1

• Making windows will not install updates 1, preserved by train now have errors 646, C355 MS12?

  I don't know what to do to solve this problem.  I tried 3 hours know how to solve this problem. And nothing I found looked like this problem. If you can help me I would be Thank YOU very much.

  Try to run the tool:

  http://support.Microsoft.com/mats/windows_update/

• Windows Vista Ultimate SP2 will not install update KB2378111 or install downloaded programs and returned with error code 80070570

  Hello... my computer will not install update KB2378111 with a code error 80070570.  In addition, I can not install all programs downloaded from the internet, specifically my anti-virus software.  I'm running without any software antivirus at this time.  I ran the most recent Microsoft malicious software removal tool and it showed that there is no problem.

  I'm running without any antivirus at this time software

  See...

  Cleaning a compromised system
       http://TechNet.Microsoft.com/en-us/library/cc700813.aspx

  Personal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows. Please note that a repair installation (upgrade AKA on-site) will NOT fix it!

  HOW to do a clean install of Vista: see the "to install Windows by performing a clean install" (or "reinstall Windows Vista") http://windows.microsoft.com/en-us/windows-vista/Installing-and-reinstalling-Windows-Vista article

  NOTE: If your computer came with a set of disks, there is a hidden partition restore (not to be confused with the restoration of the system) you would use to do the clean install (AKA a "destructive recovery").

  After the new installation, you will have the equivalent of a "new computer" in order to take care of EVERYTHING on the next page before connecting the machine to the internet or one local network (i.e. other computers) AND BEFORE to plug in a flash, SD card, or any other external drive to the computer otherwise:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  Tip: After completing the computer fully patched, download/install KB971029 manually before connecting any player external to the computer: http://support.microsoft.com/kb/971029

  VERY IMPORTANT! -Online any Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free AND download/run the removal tool appropriate prior to installing the updates, Windows Service Packs or IE upgrades AND BEFORE installing your new anti-virus application.

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  See also:

  Risks & benefits of P2P file sharing
  http://www.Microsoft.com/protect/data/downloadfileshare/filesharing.aspx
  http://blogs.technet.com/MMPC/archive/2008/10/06/the-cost-of-free-software.aspx
  http://www.us-cert.gov/CAs/tips/ST05-007.html

  Measures to help prevent spyware
  http://www.Microsoft.com/security/spyware/prevent.aspx

  Measures to help prevent computer worms
  http://www.Microsoft.com/security/worms/prevent.aspx

  Avoid fake security software!
  http://www.Microsoft.com/security/antivirus/rogue.aspx

  If you need additional assistance with the clean install, please start a new thread in this forum: http://social.answers.microsoft.com/Forums/en-US/vistarepair/threads

  If these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.

  Good luck!

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• After you have installed a second drive, computer will not install updates-error code 0 X 80070011

  Original title: it seems that since the installation of a second drive hard, PC will not install updates. They continue to fail.

  HP pc running windows 7 Home premium. error code 80070011

  Hello

  ·        What updates you are trying to install on the system?

  ·        What is an update of the application or a Windows update that you are trying to run?

  ·        If it is an update of the application, where the application, first hard disk is installed or the second drive?

  Error 0 X 80070011 occurs when you try to update any application which is not present in the location.

  For more details, see the article mentioned below.

  Error: ERROR_NOT_SAME_DEVICE (0 x 80070011)

  http://social.technet.Microsoft.com/forums/en-us/itprovistasp/thread/a2a6876d-eb2e-4238-98a9-4933ad5da996

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• My computer will not be updated Service Pack 3 for Windows XP

  My computer will not be updated to service pack 3 for windows xp, I tried to install from the Web site, as well as through automatic updates and I'm still not able to servie pack 2 on my computer and from the service pack 1 of my other... help please!

  Original title: Windows XP updates

  Just in case:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-windows_update/help-every-time-i-download-the-Service-Pack-3-for/b2ddd165-8f25-424e-8980-a55b31f87e79