Wired controller Xbox 360 connects to Windows 7, error: USB device not recognized

Similar Questions

• Error "USB device not recognized", but nothing is plugged in and my webcam is not working. It says webcam not connected

  Error "USB device not recognized", but nothing is plugged in and my webcam is not working. It says webcam not connected

  Hello

  Since you said it worked very well recently, I'll try to do a system restore at this point in time.

  See this link: http://windows.microsoft.com/en-us/windows7/products/features/system-restore?SignedIn=1

  In addition, see the response of the Meghmala and follow the instructions listed there. I think that the three method might be the best of the bunch for you, but they have all the right steps.

  See this thread: http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/usb-device-not-recognized-in-windows-7/8106a712-a13e-4ca5-b82e-c3961cc254b1

• How < I > completely < /i > reinstall a wired controller Xbox 360 on a Windows PC?

  I have a wired Xbox 360 controller, which I use on my PC and my laptop... Who is having trouble on the PC when the Vibration is enabled in games. (Among other problems)

  I read the other post, where the answer is that the bus power supply and motherboard were not powerful enough and is that which is at the origin of the problems, now I'm not saying I wouldn't totally rule this possibility, but I'm pretty confident that my PC must be capable of this (especially if my cell phone).

  I think my problem is to do the installation, because there was a problem during the installation on the PC...

  So that the Xbox 360 controller installed its drivers and what - not the first time I plugged on my PC, my friend offline security "do not pull the Xbox off the shelf" section of wire and an error, but the installation is complete. The controller has the same way as it does on the laptop, for example, the green ring just keeps blinking while on the laptop, he moved to the "Player 1" quarter. However, the feature (buttons and sticks) works well in games, crashing less vibrations.

  To be honest, I don't really care about the vibration and have just disabled in the game options, but I recently bought a game where I can not disable the vibration and so I can not use my controller with it. (sad face). That said, it would be nice to stop the flashing green light several times.

  I tried through Add/Remove programs but do not understand how completely remove everything if I do a fresh install.

  I don't know if there are any software is installed, or elements of the registry or drivers. But I need to remove what it installed so I can reinstall it without error.

  My title should have been no doubt: "How to completely uninstall a wired Xbox 360 controller on a Windows PC" since it is the part of the resettlement of which I have a problem with.

  Can someone help me?

  Thank you! (happy face with slightly concerned Front)

  Hello

  Method 1:

  I suggest you to see link and check if it helps:

  Connect a game controller

  http://support.Xbox.com/en-us/Xbox-360/accessories/connecting-game-controllers

  Method 2:

  See the link and check if it helps:

  Troubleshooting your Xbox 360 Controller for Windows

  http://support.Microsoft.com/kb/908888

  See also the link for Xbox support:

  http://support.Xbox.com/en-us/home

  I also suggest you to report the query in Xbox forums:

  http://forums.Xbox.com/?XR=shellnav

• Windows 7 and install/recognize the problems of printer HP LaserJet P2015 error - USB Device not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  Title: Windows 7 and install/recognize printer HP LaserJet P2015 teething problems...

  I have a dell inspiron that was originally windows Vista and I changed to windows7.  I have a LaserJet where I work, a HP LaserJet P2015 printer and when I plug in the USB, it says (peripheral USB not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  How and what should I do to get the printer going or to get the computer to recognize.  Installation CD will not work and I looked online and downloaded drivers but still the same thing.

  Hi LOliver,

  Method 1: Run the hardware and peripheral troubleshooting tool and check if it makes a difference.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: Disconnect all USB (Universal Serial Bus) devices connected to the computer (unless your mouse and keyboard). Connect the printer and check to see if the problem persists.

  Method 3: Connect the printer to a different USB port and check.

  Method 4: Reinstall the USB (Universal Serial Bus) controllers.

   First of all, please disconnect all USB devices and then perform the following steps:

  (a) click on 'Start', type device manager in the search bar and press "Enter." If necessary, click on continue.

  (b) in Device Manager, double-click to expand the "USB Bus controllers", right-click on the "host controller", click "Uninstall" and click "OK".

  (c) repeat step 2 to uninstall all items under 'USB Bus controllers'.

   

  Then, restart your computer and windows will automatically reinstall all USB controllers.

   

  HP printer drivers- ensure that you download the driver appropriate for your device model package.

   

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• We get the popup "USB device not recognized", when nothing is connected.

  Original title: pop up message

  I connected the USB cord to transfer information from your old phone to new phone via Itunes.  Since that time that I keep getting a pop up message that says: device not recognized USB, the defective device, windows does not recognize.  Nothing is plugged in, but message appears every few seconds.  How can I get him to stop?

  Hello

  It seems that you are getting the popup "USB device not recognized", when nothing is connected.

  What is the brand and model of your computer?

  I suggest to uninstall the USB controllers and check if you get the context menu.

  
  

  Method 1: Remove and reinstall all USB controllers

  
  

  a. clickStart, type devmgmt.msc in the start search box and press ENTER.

  b. expandBus USB controllers.

  c. right-click on each device under theBus USB controllers node and then click Uninstall to remove them one at a time.

  d. restart the computer, and windows will install the rear USB drivers.

  If reinstalling USB host controllers fails to resolve the issue, go to method 2.

  Method 2: See the procedure suggested by johnkelly46 responded on October 26, 2009, from this link.

  If you have additional problems, please reply to this post and we will be happy to help you further.

• Windows 7 - "USB device not recognized" - to load the new electronic Cigarette device. Help, please?

  I have Windows 7 Home Premium.  I just bought a unit of the electronic cigarette, manufacturer is "Innokin Cool Fire IV", the usb charger plugged on Acer laptop and comes to the screen "USB device not recognized".  I loaded different brand before without problem, I don't know what to do and I am NOT GOOD WITH COMPUTERS!  My settings are at "install updates automatically" and I DON'T WANT WINDOWS 10!  Can someone help me please?  Thank you for taking the time to read this.

  This seems to indicate that the charger has actually been detected as a device, but Windows can not work it out.

  Normally such a device should only connect to 5v and 0v pins and have no connection with the pins of data, in this way, that it will not be seen by Windows. I would be concerned by the quality of the device if it has some form of data connection. If you want to continue with this charger, that I would recommend to use a power supply of 5v USB instead of risking the USB port of the laptop, a lot less expensive if it does not. It has been reported several eCig Chargers catch fire. Something like this:

  

• USB device not recognized when I connect my iphone to my computer

  Original title: USB device not recognized

  I get the error message "Unrecognized USB device" when I connect my iphone to my computer.  It is the same as the one I use for months.  Same computer.  Same sync cable.  I have changed everything, including hang iphone to my wife instead of mine and get the same message.  I also did a restore on my computer that doesn't change anything.

  Hello

  At this point, I think it's a good idea to run a scan for viruses/malware on the PC with the anti-virus software that you have installed.

  Also, if you haven't already, I would try removing the USB controllers and restart again, now that the updates of Windows are installed. Don't forget, you can even download the drivers directly from manufacturer support site for your PC, if they install automatically when you restart after their removal.

  Finally, take a look at the thread I linked below. The first answer is quite similar to that mentioned above in this thread, but there are also a few other really good measures listed there as well. Then take a look at the linked thread and see if that helps at all.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/USB-device-not-recognized-in-Windows-7/8106a712-A13E-4ca5-b82e-c3961cc254b1

• USB device not recognized in windows 7

  USB device not recognized in windows 7

  Hi eyadOdetallah,

  -Is the issue specific to a particular USB device?

  -What software changes you did on the computer before the show?

  Follow the steps below:

  Method 1:

  Run the hardware and devices Troubleshooter to run the automated troubleshooting services.

  Open the hardware and devices Troubleshooter

  Disable and re-enable all the USB controllers.

  Method 2:

  This allows controllers to recover the port USB of his condition does not respond. USB controllers represent the USB ports in Device Manager.

  To disable and re-enable the USB controllers, follow these steps:

  a. Open the Device Manager.

  b. expand Bus USB controllers.
  
  Note that you have to scroll down to find this point.

  c. right-click on the first USB controller under Bus USB controllersand then click Uninstall to remove it.

  d. Repeat steps above for each controller USB is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

• Xbox 360 connects to Windows Media Center (Windows 7-64 bit)

  I can't get my Xbox to connect to Windows Media Center.  When I ran Vista it would work, but now that I am on Windows 7, 64-bit, it just does not connect.  The strange thing is that I'm able to share media from my PC to the Xbox without fail.  In addition, Windows Media Center has detected the Xbox on the network.  But for some reason, the Xbox cannot find the Windows Media Center.  It makes no sense at all.  I even tried disabling the Windows Firewall to see if it would work, but it didn't.  There is no other firewall in my home network.  Help, please.

  Hi Imautobot,

  You may need to configure the Xbox extender for Windows Media center for Xbox to work.

  Step 1: Get the key Setup of Xbox 360
  1. on your console, go to my Xbox, and then select Windows Media Center.
  2. follow the on-screen instructions.
  3. write down the 8 digit Media Center Setup key.

  Step 2: Add an Extender on your computer
  1 start Windows Media Center.
  2. click on tasks, and then click Add Extender.
  3. When prompted, enter Xbox 360 8-digit setup key.
  4. complete the configuration of the Extender.

  See the links below: connect your console to the Windows Media Center: http://support.xbox.com/support/en/us/nxe/xboxlive/troubleshooting/NetworkHelp_mcxpc.aspx

  Enjoy Windows Media Center on the Xbox 360 with your music, photos, Live Recorded TV and online media: http://www.Xbox.com/en-us/pcsetup/MCEWindows7.htm

  http://www.Microsoft.com/Windows/Windows-Media-Center/learn-more/Extenders/tutorials/Extenders-Xbox-config.aspx

  Set up a Windows Media Center Extender unit: http://Windows.Microsoft.com/en-us/Windows7/set-up-a-Windows-Media-Center-Extender

  Tips for solving problems with Windows Media Center Extender Setup: http://Windows.Microsoft.com/en-us/Windows7/tips-for-solving-Setup-problems-with-Windows-Media-Center-Extenders

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• USB device not recognized when connected to Toshiba Port Replicator II

  I recently bought the Replicator above, loaded the software, restarted my computer and only then connected the device according to the instructions.

  I get the error message "unrecognized usb device".
  When I go in my gear and check for driver for this device 'unknown' told me that no drivers have been shipped for her

  So my Replicator does not.
  I deleted the software and reloaded with the same result

  I have a laptop Tecra A8 running Windows XP Service Pack 2
  Any help or suggestion would be appreciated

  As much I know PortReplicator II only is not supported for Tecra A8. According to the sustained specification is Port Replicator III + only.

  If you try to use the option not supported, it is not easy to give any help.

• USB device not recognized when connecting to printer

  Hello Microsoft,

  Hear I have problem in my PC. I connect to my new printer (RIOCH SP 100), but in my Winodws7, they show me that your usb device is not recognized. I try to use the resolution of problems. but it was a failure of dem, so now what is the way to solve my query.

  Hello Dhruv,

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the complete model of your printer RICOH SP 100 number?

  Thank you for details on the issue.

  This problem may occur because of settings and corrupt device drivers.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the hardware and devices Troubleshooter and check.
  Reference:
  Open the hardware and devices Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  It checks the common issues of interest and ensures that a new device or hardware connected to your computer has been installed correctly.

  Please also run the printer Troubleshooter and check.
  Reference:
  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  He made sure that a printer is connected to your computer, and it checks for common issues such as whether the printer has enough paper and toner to complete printing your document.

  If this does not help, use method 2.

  Method 2:
  Controllers USB reinstall and check the issue. Please follow these steps:

  a. press Windows + R keys together, type devmgmt.msc in the run window and press ENTER.

  (b) in Device Manager, expand 'USB Bus controllers'.

  c. right-click any device under "Controllers of Bus USB" and click Uninstall.

  d. repeat the same steps for other devices.

  e. Once completed, restart the computer.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• USB device not recognized when connected to the computer

  original title: USB port problems

  When I plug a usb device, I get a message not recognized usb device (one of the usb devices attached to this computer has malfunctioned and windows does not recognize)

  Hello

  ·         Since when are you facing this problem? Were you able to use this USB device on the system before?

  ·         Remember to make changes to the system?

  ·         It happens with all USB devices that try you to plugin for the system?

  I suggest running the fix which is present in the article below and check if the problem persists.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Also, I suggest you return the item mentioned below.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

  http://support.Microsoft.com/kb/925196

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.

• Wired Controller Xbox 360 Windows 8. How to operate without the xbox 360 turn on do you get?

  Windows 8 recognizes the controller. I have to do something special with regard to the implementation of the controller? I have to disconnect the xbox360 so it does not start it.

  Thank you.

  Check this box

  http://support.Microsoft.com/kb/933710

• USB device not recognized. -"peripheral USB attached to this computer has a malfunction and Windows does not recognize it."

  My phone displays a warning that a "peripheral USB attached to this computer has a malfunction and Windows does not recognize it." I uninstalled the only devices that I had (printer and bluetooth) but still this warning. Can anyone help.

  Mike S.

  I suggest to take a look at the following Web sites and follow their advice:

  http://support.Microsoft.com/kb/871233

  http://support.Microsoft.com/kb/310575

  http://support.Microsoft.com/kb/314464

• Gamepad - "Device not recognized USB" Windows 7 32-bit

  I own an INTEX it-gpo2 plugnplay Gamepad... earlier it used to work well... but these last days, when I connect it to my pc an error indicating "USB device not recognized" I HAV changed the port, but it shows the same error... I HAV tried also to install the drivers provided on the cd, but it also won't work... someone please help...

  Hi ArkaBarman,

  This problem is usually caused due to hardware or driver related issues. I would like to know some information about this problem so that we can help you further.

  1. have you made changes on the computer before this problem?

  2 What problem confined to the joystick?

  3. have you tried to connect the gamepad on another computer?

  4. What is the model of the joystick number?

  I would suggest trying the following steps and check if it works for you.

  1. click on Startand then click Control Panel.

  2. click on system and Maintenance, click System, and then click Device Manager.

  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  3     in Device Manager, double-click on it to develop a 'Bus USB controllers', right click on the controller host, click "Uninstall" and click "OK".
  4. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Please respond with more information about this problem so that we can better help you.