Wireless ISP and NATing / Remote access

Similar Questions

• 4402 wireless controller and the 1130AG access points

  I have a bunch of 1130AG (35) and 1231 points of access. I just bought a controller 4402 so I could handle these much easier access points. I currently have the offline access points, so I could control. With the wireless in the mix controller, that I have to fix these to light mode or can I leave them offline.

  We know not the operating instructions so I can leave them in stand-alone mode. Most of them is in the rafters in our warehuse, and I didn't have to pull of these if I have to. If I can use them offline, how can I do that?

  Thanks much for any info!

  Dave

  Hi Dave,.

  A WLC manages autonomous APs.
  So if you want to centralize the management of your APs through the WLC, you will need to convert it to light and enter them on the WLC.

  To convert the lightweight access points, you can choose between several options:

  1. thanks to a specific upgrade tool that you could install on a PC:
  http://www.Cisco.com/en/us/partner/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html

  2. [the most evolutionary] by WCS, with a model of migration that could apply to several APs:
  http://www.Cisco.com/en/us/docs/wireless/WCS/7.0/Configuration/Guide/7_0apcfg.html#wp1054876

  3. [not in any book] by the following steps:
  3 (a) download the CEC lwapp recovery image and store it on a TFTP server.
  3 (b) Telnet to the stand-alone PA and issuing the following command:
  Archive Download-sw / overwrite/reload tftp: / // [lwapp recovery image file path]

  As a general recommendation, before to convert the lightweight access points, you can be sure that the wired infrastructure behind is ready to direct them to the WLC for recording.
  It's suggestions explained in the link on the above option #1.

  Hope this helps,

  Fede

  --
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Back to my Mac drive remote access

  I tried to set up my Time Capsule and the hard drive connected to it to be accessible on the internet via Back to My Mac. My Time Capsule is the main router and the modem to the ISP provided is in bridge mode. I followed the instructions of installation to the letter, but it still not connect when I try to on the internet. I tried to connect life iPhone tethering and friend home as well with no luck.

  Tried to help out a little and when I go to the iCloud tab in system preferences, I get the following message on the CCMM: Back to My Mac can be slow because multiple devices on your network provides network services. Turn off NAT and DHCP on one of the devices and try again.

  The problem is that NAT is enabled, my Time Capsule is set up for back to my Mac and I enabled sharing of files on it, as well as on WAN access records. I also tried the deactivation and activation CCMM on both Time Capsule and in settings iCloud, still the same error. My only goal is to be able to connect to the Time Capsule and access the files remotely.

  I hope someone can help.

  Thank you!

  provided the ISP modem is in Bridge mode

  It may or may not be, because ISPS generally have some strange ideas about what the term "Clipping" might mean.

  What is the number and model of your modem?

  If all goes well, it is a simple modem.. .with a single Ethernet port the device... as in the example just below, which is the type of device that you really need to be able to access on your network from the Internet devices.

  

  I hope once again, it is not a type of modem/router or gateway device, which combines the functions of the modem router and separated in one package... as in the example below. Often, it is not possible to configure this type of law only as a simple modem device... and what the ISP calls 'Clipping'... is not really. Thus, you're left with a problem NAT which slows down and restricting remote access.

  

• Static IP remote access for the media center

  I NMH410 work through a WRT610N router.   My ports are configured for static IP access.  Seems to just going through www.ciscomediahub.com does not work well for me.

  Can someone provide the 'exact' URL I would enter in order to access my media center?

  Documentation of assistance through Cisco shows: https://Wan_IP_Address but that doesn't seem to work.  The demand is just there and finally once outside.

  To everyone:

  Apparently, I discovered and corrected the problem that I had with 'Remote access' to my Media Hub.

  Somehow, there are two configurations of router that had to be done.  On two port forwarding configurations has been necessary and once allowed me to access the media center.

  It seems that my ISP has a 192.168.x.x address router that was different from the address of my router 192.168.x.x.  It is on the home router when I incoming and make changes to the information of port forwarding.  The fact that I was getting an error message indicating that I wasn't even reached my router alerted me to the fact that my ISP was blocking remote access.  In the end, that's where my problem was discovered.

  Translate:

  If you have problems to access your media "at a distance" pole through its IP address (and not by the cisco media center), make sure that you configure the ports of the router specified by your Internet provider address, as well as the ports of the router that you have on your network home.

  I have forwarded port 443 on the two addresses of router port, and I can now access my media hub remotely.  Now if I can't play videos remotely, I'll be set.  This leads to another problem that I'll send it in another thread.

  Thanks for the help and suggestions of each.

• Remote access VPN Cisco 1811

  Hi forum

  My question is very simple. At my office, we have a Cisco 1811 router that is connected to our internal network. Dialer0 is connected to our ISP. We have an IPSEC tunnel running between one of the branches to a different place. Our 1811 is not a mainstream, and we have another firewall for remote users. But the problem is one of the workstations is a MAC book wouldn't connect to our firewall so I had him put through 1811 to access internal resources.

  Since I am under an IPSEC tunnel on the interface dialer0 how to configure VPN Client Access and how I map it to the dialer interface.

  Your help is greatly appreciated

  Thank you

  Attached, is an example of configuration that you can use to serve the site-site static and dynamic remote access on the same router.  Please let me know if you have any specific questions.

• Failed to start remote access service

  Hello

  I get a vps and I install ca and iis and the remote access service

  I allow it as a vpn server

  When I try to run the remote access service there gives me an error

  The Routing and remote access is dependent on the Remote Access Connection Manager service, which could not start due to the following error:

  The dependency service or group was able to start.

  I reslove this problem to run these commands:

  netcfg u ms_sstp

  netcfg - c p-i ms_sstp.

  net start sstpsvc

  net start rasman

  now when I am tempted to throw there gives me this error:

  The Remote Access Connection Manager service terminated with the following error:

  The system cannot find the specified device.

  So what is the problem?

  Thank you.

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft TechNet forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/categories

• Problems with Windows 7 Pro Remote Access

  I'm on a Windows 7 Pro machine, but it is connected to a working network.

  I'm trying to access Windows 7 Pro machine to my parents at home.

  I went through These Instructions.  We have created a password for one of the user accounts.  I checked the name of the computer (there is no listed area).  We confirmed that remote access has been enabled and allow remote access has been verified in the firewall settings.

  However, when I start "Remote Desktop connection" on my computer and put their computer name in the box, I get a message that it cannot find the computer.  Then, the message indicates that the computer cannot belong to "the network specified."  But there is no specified network, and I see no where to do it.

  In addition, it is possible that my work security settings prevent me from remote accessing another computer?

  Last question: if I used the Fusion of the virtual machine on my Mac, with Windows 7, I can remote access to another computer?

  Real technique.  The problem boils down to the IP address.  Your computer probably has an IP of 192.168.1.8 or something like that.  But the router any fact domestic in the world.  So when you want to connect to the remote computer, you must use the IP public face (which the internet service provider home assigns to your router/home, not that of your router assigns to your computer).  But then, you're always short because now you have at home, but you have to tell the House what PC actually send this letter too.  It's like an envelope with an address half. Port forwarding it tells the final step which PC should receive the message.

  But yes I agree they could at least put a link or an explanation.

• exsi how to remotely access safely

  Hello

  I'm building a lab at home consisting of a router and a server. The plan is to install exsi and a couple of windows on top of exsi servers.

  I need distance in the laboratory of the internet servers and also remote access to the exsi (to manage).

  How can I set this up, I was thinking about vpn for windows servers, but what about the noninale of exsi?

  Thank you

  You could RDP in a windows machine in your laboratory and then manage ESXi from there.

  Set up a VPN or open a port for RDP through your router.

• Windows disabled remote access to my wireless printer

  My printer is connected wireless to the computer at home (so a 'network', I guess).  But the recent problems led me to authorize remote technicians, and apparently, as collateral damage, my printer does not print now.  At one time gave a convenience store, I found a statement that "Windows has denied access to distance", but I can't find out how to restore remote access.  Printer is now installed, and the work and watch as the default printer, with options for "start printing immediately.

  Anyone know how to force Windows to restore remote access to my computer to the printer?

  Thanks in advance

  Rich

  Hi rich,

  Follow these methods.

  Method 1: Follow the steps in the article.

  Resources for the resolution of the printer in Windows XP problems

  http://support.Microsoft.com/kb/308028

  How to troubleshoot a network home in Windows XP

  http://support.Microsoft.com/kb/308007

  Method 2: Uninstall and reinstall the network drivers.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  For reference: printer in Windows problems

• Can not get to start remote access connection manager and the connections don't work Internet

  Original title: wired & wireless connections does not.

  I can not get the remote access connection manager to start and so no internet connection is not working, also I can't open the system restore to go back on this machine. What is this?

  I am running a Dell Studio 1735 PP31L w model number / Edition Vista Home premium.

  Hi Rick,

  1. what happens when you try to start the remote access connection manager? You receive messages or error codes?

  2. you receive error codes or restore messages when you perform the system?

  You can check the status of the following services and make sure that the services are started.

  a. Click Start and type Services in start search and press ENTER.

  b. in the services with the right button on the phone and then click Properties.

  c. under the general tab, select automatic next to startup type.

  d. under the general tab, click Start under the service status and then click apply and then click OK.

  e. Repeat steps c & d to the remote access connection manager and Remote Access Auto Connection Manager service.

  Hope this information is useful.

• stop windows remote access connection and access the CD dirive

  I use windows 7 ultimate 32 bit OS

  There is a problem called "windows remote connection" which is not allowing me to access the CD drive for CD writing

  no disc burning software nero8, ashampoo burning studio, power iso; None of them can write data to dvd using my dvd burner

  I need solution; What kind of sequrity program is this "Windows remote connection?

  Here's how to turn on remote desktop (and therefore, how to disable - just check the other box):http://www.howtogeek.com/howto/windows-vista/turn-on-remote-desktop-in-windows-vista/.  See if the ' turn off resolves the problem.  If necessary, try to turn off remote access as well (above) - If this does not work, put in the less remote access back on (you may need it if you need someone to connect to your computer for assistance - as your ISP or Microsoft Support or even a computer repair shop that works remotely).

  This isn't a security feature, but a function of access to allow others on the internet to connect to your PC and you can connect other PCs (and show their desktop and work with their mouse on your computer - or they can do the same with you the authorizations if many use other 3rd party software to do this work easily and smoothly).  FYI, here's how to use remote desktop in Windows 7:http://forums.techarena.in/guides-tutorials/1187281.htm.

  If this does not work, please repost your question in the Forums Windows7: http://social.answers.microsoft.com/Forums/en-US/category/windows7 where Windows7 experts will be happy to help you.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to configure VPN remote access to use a specific Interface and the road

  I add a second external connection to an existing system on a 5510 ASA ASA V8.2 with 6.4 AMPS

  I added the new WAN using another interface (newwan).

  The intention is to bring more internet traffic on the new road/interface (newwan), but keep our existing VPN using the old interface (outside).

  I used the ASDM GUI to make changes and most of it works.

  That is to say. The default route goes via (newwan)

  Coming out of a VPN using a site to character the way previous (out) as they now have static routes to achieve this.

  The only problem is that remote incomming VPN access Anyconnect do not work.

  I put the default static route to use the new interface (newwan) and the default tunnel road be (outside), but that's the point is will not...

  I can either ping external IP address from an external location.

  It seems that the external interface doesn't send traffic to the - external interface (or at least that's where I think the problem lies). How can I force responses to remote VPN entering IPS unknown traffic to go back on the external interface?

  The only change I have to do to make it work again on the external interface is to make the default static route to use external interface. Calling all internet traffic to the (external connection) original

  Pointers appreciated.

  William

  William,

  As it is right now that you will not use the same interface you have road to terminate remote access unless you know their IP addresses by default.

  In one of the designs that I saw that we did something like that.

  (ISP cloud) - edge router - ASA.

  The edge router, you can make PAT within the interface for incoming traffic on port udp/500 and UDP/4500 (you may need to add exceptions to your L2L static) of the router. It's dirty, I would not say, it is recommended, but apparently it worked.

  On routers, this kind of situation is easily solved using VRF-lite with crypto.

  M.

• L2l VPN and remote access VPN

  Hello

  I have 2 Cisco Pix (Pix1, Pix2) 515E (8.0.4). Between these devices exist VPN L2L, which are configured on the external interfaces. On Pix2 I configured remote access VPN on the external interface, too.

  Is it possible to achieve LAN behind Pix1, by using remote access VPN on Pix2 then VPN L2L?

  I don't want to set up remote access on Pix1.

  Thank you very much.

  Kind regards

  Vladislav

  NAT (outside) 1 140.40.30.0 255.255.255.0 (PAT for RA vpn to access the internet if you complete tunnel)

  It is simply because I have configured tunnel RA as complete tunnel instead of split, nat (outside) 1 at the RA 140.40.30.0 pool have internet access through your firewall ASA_SITE_B and translate with global ID 1 who is your external interface of the firewall SA_SITE_B. This has nothing to do with what you are trying to accomplish, but I posted it because it was part of the very common scenario. There are some example PIX 6.3 cases where you will need split tunnel so that RA users have internet access not passing not through the encrypted tunnel code 6.0 does not feature of intra-interface support but 7.x above is of the code. Other examples are that some people configure split RA RA user tunnel will have access to their local resources in their homes as the printers network etc...

  It is therefore, I need to translate 172.27.1.0/24 RA pool?

  No there is no address translation in place in this scenario to work and you don't need to translate something too long, there is no of networks that overlap in one of the SITES u do not need to translate, this scenario is completely free sheep as you access lists free of nat in two firewalls for networks involved in communication in tunnels ASA_SITE_B.

  Because I want to see IP addresses from PIX_SITE_A to 172.27.1.0/24, not 140.40.30.0/24. Is it possible to do it this way?

  Im not clear on this issue, but if I think what it means, it's possible but you need to have political NATing but I think this will make complicated setup, I would say to make this as simple as possible.

  Concerning

  All helpful PLS rate valid if it helped

• How can I enter username and password to access my pasworded on Server ISP space

  I need to view and download files on my space web page on my ISP server. I can connect using "via ftp. (ISP) .com but must enter my user name and password to access my files. How do I do this in Firefox?

  You can prepend the URL with the user name to force Firefox to display a pop-up connection.

  • http://[email protected]/
  • FTP://[email protected]/

• Routing and remote access - on three subnetworked, two subnet unable to reach to the internet!

  Hello

  Good evening everyone.

  I had a problem in Routing and remote access on windows 2003 server.  This server is already configured as a file server, domain server, and application server. Also configured as a router (thanks to access routing & remote) to connect the three different networks with each other. If this server has three NICs installed and each separate NIC network cards represent.

  three different networks are - 192.42.160.0/24, 192.42.161.0/24, 192.42.162.0/24

  Three cards of the NETWORK adapter installed on the server as with the IP - next

  NIC - 1 = 192.42.160.220, Sub - 255.255.255.0, gateway - No.

  NIC - 2 = 192.42.161.220, Sub - 255.255.255.0, gateway - 192.161.220.112 (this ip address for internet access then 4 g router IP)

  -3 = 192.42.162.220, NETWORK cards, Sub - 255.255.255.0, gateway - No.

  Now the question is I can get Internet & (also scathing in router ip 192.42.161.112) one network i.e. - 192.42.161.0/24, BUT when I try to access the internet from another two network (192.42.160.0/24 & 192.42.162.0/24) I can not access and in addition can not ping to internet router ip - 192.42.161.112...

  So, how do I access the internet to another two network also?

  I was already the configuration of static routing for all three network but I wasn't always successful. I don't really know what exactly static routing this should be done in access routing & remote area so that all three network can reach to the internet?

  Here is the result of the current track...

  D:\Documents and Settings\Administrateur > route print

  IPv4 routing table
  ===========================================================================
  List of the interface
  0x1 ........................... MS TCP Loopback interface
  0x2... 00 30 05 8f ad 5 c... Broadcom NetXtreme Gigabit Ethernet - Mi Teefer2
  niport
  0 x 3... 0E 00 c4 f8 a7 0c... Network Intel(r) PRO/1000 GT Desktop Adapter - Teefer2 M
  iniport
  0 x 4... 0E 00 0c a7 c5 85... Intel (r) PRO/1000 GT Desktop Adapter #2 - Teefer
  2 miniport
  ===========================================================================
  ===========================================================================
  Active routes:
  Network Destination gateway metric Interface subnet mask
  0.0.0.0 0.0.0.0 192.42.161.112 192.42.161.220 1
  127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
  192.42.160.0 255.255.255.0 192.42.160.220 192.42.160.220 20
  192.42.160.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.160.255 255.255.255.255 192.42.160.220 192.42.160.220 20
  192.42.161.0 255.255.255.0 192.42.161.220 192.42.161.220 20
  192.42.161.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.161.255 255.255.255.255 192.42.161.220 192.42.161.220 20
  192.42.162.0 255.255.255.0 192.42.162.220 192.42.162.220 20
  192.42.162.220 255.255.255.255 127.0.0.1 127.0.0.1 20
  192.42.162.255 255.255.255.255 192.42.162.220 192.42.162.220 20
  224.0.0.0 240.0.0.0 192.42.160.220 192.42.160.220 20
  224.0.0.0 240.0.0.0 192.42.161.220 192.42.161.220 20
  224.0.0.0 240.0.0.0 192.42.162.220 192.42.162.220 20
  255.255.255.255 255.255.255.255 192.42.160.220 192.42.160.220 1
  255.255.255.255 255.255.255.255 192.42.161.220 192.42.161.220 1
  255.255.255.255 255.255.255.255 192.42.162.220 192.42.162.220 1
  Default gateway: 192.42.161.112
  ===========================================================================
  Persistent routes:
  None

  Sorry if I'm not able to explain properly. Please let me know if you have to explain more about it...

  Thank you all.

  Mahesh

  Hello Manu,

  Please post this question in the forums TechNet for Windows Server 2003. They will be able to guide you further.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home