Wireless network problem: disconnects randomly anywhere between 1 and 4 hours.

I have a wireless network problem, it disconnects randomly anywhere between 1 h and 4 h. The network consists of a Samsung 4 G hotspot and a Linksys AE1000. The signal strength is excellent, the AE1000 is 1 ft of the computer and 1 ft of the HotSpot.  The computer is a Dell Dimension 2400. Any ideas?

Hi Jack,

Problem solved.  I did 2 assumptions about the original problem.  I assumed that the 2 Tech that I spoke made the hurt their product. Battery saver has been activated on the hotspot.

Thanks again

Greg

Tags: Windows

Similar Questions

  • How to build a VI that generates a random number between 1 and 80... Help!

    Generate a VI that generates a random number between 1 and 80

    Divide the random number by a number specified in the front panel.

    If the number of seizures is zero, the VI program should light a LED in the face to indicate a divide by zero error.

    Hai edwardty2009,

    Welcome to the forum.

    Thanks for the congratulations.

    Your problem is solved? If so can you please mark as solution what post help better to solve your problem.

    Thank you

    Mathan

  • Let a burn of LED on a random time between 3 and 7 seconds

    Hi all

    Probably, it's a matter of simpel for many of you, but not for me. I try to make a counter reaction time. And I hope someone can help me with the first part: the led must Flash on a random time between 3 and 7 seconds.

    After this need to measure the time between burning directed and by pressing the stop button

    Results ranking in a table

    After the display of ten measures of response time average.

    I hope someone can help me to launch it, I need it for school.

    Thank you!

    Matthijs

    Netherlands

    Code Simon put tapped off.  The Down button was a nice touch, but cannot be disabled so we were testing times preaction and the param 'Trial' could get pretty messy especially on a series of rehearsal

  • card 3160 AC wireless network problems

    Hello

    I bought a laptop HP Envy M6; product # G5N44UA #ABA running Windows 8.1 64-bit, and I have a problem with the wireless network card. It is a version of Intel dual-band AC3160 wireless 16.6.0.8

    The problem is that when I close the lid, do go to sleep or turn off the computer, it restarts when it says that it cannot connect. When I run the troubleshooting it says that there is something wrong with my (physical) access point. If I run the access point troubleshooting it reboots the access point which solves the problem, until he falls asleep again.

    What did I try? So far...

    (1) uninstalled and reinstalled the driver. No change.

    (2) changed some settings about «closing the lid» power management Changed for the 'status quo' when lid closes.

    Now when he goes to sleep or if there is, it does not detect the network at all unless I restart again.

    I changed the rear power settings, but I need to know if I have a hardware problem and how to get fixed.

    Thank you

    I was intrigued by the validations and proposed solutions to the question of the network adapter 3160.  I have a 8 month old G0T55AV of HP Envy 15 t-K000 Notebook 64-bit Win 8.1 with 12 GB of Ram, and of course the AC adapter / 3160 of Intel.  I should mention that I am a fan of long-time HP products.  It's my second computer of this model as first a miserably failed with Touch Pad questions and passing AC 3160 failures, if HP has requested that I return it and they were replaced by a new.  Shortly after I received my other 'News' that also came with the AC3160, I started having network disconnects when you wake up mode "Eve".  I found articles about uncheck the power saving mode.  That worked for a while and all of a sudden, I once again began to have problems.

    I contacted Tech Support Chat repeatedly and most recently of several days.  They diagnosed the problem and as usual tried to remove and download the drivers that had been made several times previously.  They also disabled several of my 'start-up' services and was intending to leave them turned off until I challenged, who also screwed up some of my services.  I also noticed that now I could not the PC to recognize the adapter in wake up.  I have to restart the PC to refresh and identify the adapter, a problem that I had not seen before.   If after all this, the recommendation was to perform a factory reset.  I objected, so I was sent a box to ship my computer in for 7-10 days service center where the reset would be carried out.  Of course, I had to delete all my data and it should reinstall all software installed after initially receiving the computer 8 months ago.  WHAT?  Of course, it would be no monetary cost to me; However, the grief of being without my PC and reload data and software has been a big emotional event.

    I took a chance to solve on my own.  HQ 3160 being an Intel product, I went to the page 'pilot' of the Intel website specifically for the AC 3160.  I noticed that the iteration of driver used by HP several iterations behind the current driver from Intel.  I tried using the program to automate the update of the Intel driver.  The program has identified the adapter such as the need to update; However, the pilot would not move through their utility.  Do not know why.  I finally found a link on their site which allowed me to download and install the most recent driver manually.  I've been running for almost a week and so far, I had no network card failures.  Without losing the connection on sleep, without losing the identity of the card, nothing.

    I do not claim that it would work in every situation of AC3160 has failed, but it seemed to work for me at least to date.  My shipping box to return my PC arrived Friday 2/13; However, I hold that the driver will continue to operate successfully.  This brings a few questions in mind:

    (1) why the HP Technical Support uses them most recent updated driver from the manufacturer?

    (2) why not HP own up to the fact that the AC3160 may be defective, issue a reminder and replace them?  I know the answer! $$$$$$$

    (3) why HP joined with Intel and provide a common solution to the end user?

    (4) why HP does not provide a specialty within Technical Support Group to deal only with issues AC3160 to prevent "groping" solutions that could potentially cause more harm than good?

  • Wireless network connection disconnects when you plug in the charger and the error message "no connection available or limited connectivity.

    Original title: wireless computer does not work when plugged in and load, why?

    have a laptop Windows 7 who had originally installed XP. I have not changed anything inside her, but suddenly one day any time, I have the unit plugged my Ethernet and wireless turns off. As soon as I unplug it, the computer note immediately that there is a wireless card and connects.


    The computer has never done this until two weeks ago. It works just fine when unplugged, but still once, as soon as I plug it in it disconnects and States they has "No connection available" or "limited connectivity". I started seriously annoyed because it's my main laptop and I must wait for it to load in order to do something with him for an extended period of time.
    The device information:

    > Ze2000 HP (Pavilion series)
    > Original OS: Windows XP Home Edition
    > RAM: 512 MB
    > 100 GB hard drive
    > AMD Turion 64 Mobile Technology ML-34
    ___________________________________________________________________________________________________
    I can provide information. No errors appear in the error log or event viewer and I made backups and reset 3 times in recent weeks.

    Hello

    I appreciate your efforts to solve the problem.

    This problem may occur corrupt or incompatible drivers, missing updates or because of incorrect network connection settings.

    Are you having the same problem when you use the configuration of a network connection?

    I suggest you to check if there is no wireless or mobile network\devices which can interfere with the wireless network and remove if there is.

    Method 1:
    I suggest you to download and install the latest network driver on the manufacturer's Web site and check if it helps.

    Check out the link:
    http://h20000.www2.HP.com/bizsupport/TechSupport/ProductList.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=442888&TaskID=135

    Method 2:
    If the problem persists, I suggest you try the procedure described in the article and see if it helps.


    Wireless and wired network problems
    http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab4&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

    Method 3:
    If the problem persists, I suggest you to check that your device is allowed to the computer.

    a. click on start and type Device Manager in the box start the search .

    b. open the Device Manager and expand network adapter.

    c. right-click on the network driver and click Properties.

    d. click the power management tab.

    e. uncheck all options.

    f. click OKand then click OK again.

    See the article and check if that helps.

    Why can't I connect to the Internet?
    http://Windows.Microsoft.com/en-in/Windows-8/cant-connect-to-Internet


    Hope this information helps. Answer the post with an up-to-date issue report to help you further.

     

  • Tecra 9100 wireless network problem

    I'll have a chance by putting my Tecra 9100 with my home wireless network. The network seems to work very well. My other laptop connects to it without any problems and I can connect the Tecra with the ethernet cable. But the wireless connection, it cannot be successfully established by the Tecra.

    She claims to be connected, but he receives no package, and could get no internet connectivity. When I try to 'fix' the connection, it sits there for a while before telling me that the IP address may not be renewed.

    I managed to connect the Tecra to the network of the next door without penalty, which suggests that there is some kind of problem with our network interface. I tried to reproduce the exact settings from my other laptop, so I don't understand what the problem is.

    Any idea would be appreciated with gratitude!

    Hello

    It's really not easy to say what is happening here. The functionality of the laptop is ok and it's very confusing if it works with other local wireless networks.

    I recommend putting your access point to the factory without some specific parameters settings and try to connect it.

    Sorry, but I don? have another idea.

  • ReadyNASOS 6.4.0 - T136 (beta 4) - network actions disconnect randomly

    After you have installed the latest beta version of ReadyNAS (T136) my network shares are randomly falling sporadically.

    Model: ReadyNAS 102

    SW: 6.4.0 T136 Beta 4

    Network connection: CAT6 Ethernet

    -Tired of changing the cables, always randomly disconnects

    -Tired another port on the router, always randomly disconnects

    Protocol: AFP

    Any suggestions? I'd be happy to send the log files. I am not versed in the Netgear ReadyNAS log files, so I haven't looked at them.

    Which firmware you would update go?

    What version of Mac OS X you are running?

    Yes, send logs (see newspapers of sending a link in my signature).

  • Hp1102w connection printer wireless network problems

    I can't get my connection between my Linksys WRT54G and my printer wireless hp1102w wireless. The configuration page shows the following: network not connected, I have a host name, hardware address. There is 0.0.0.0 for IPv4, the IP subnet mask & gateway IP. Configured IP said manual.

    Under wireless 802.1b/g/n: status: activated, common mode: infrastructure, my name network & authentic WPA/WPA2
    Under Direct Print Config: Off, HP-Print-40-Laser Jet 1102, Channel 6 and there is an IP v4 address. What should I do?

    Also my iPad4 does not see the hp1102w printer, do I have to download the software? I don't have a USB connection? I am very new to the Apple OS, if you couldn't tell.

    Salvation, TarNation,

    Welcome to the HP Forums, I hope you enjoy your experience!

    I understand that you are unable to set up the printer on the wireless network.

    I'll be happy to help you.

    Please provide the following information so that I can better help you.

    What operating system do you use?

    Mac OS X: how to find which Mac OS X Version is on my computer?

    You also have a PC?

    Once the printer is configured on the network, the Ipad connects on behalf of network from the router and the printer should allow you to print using Airpint. You don't need to download software for the Ipad.

    Thanks for posting on the HP Forums.
    Have a wonderful day!

  • Envy 14-3010NR card wireless network problems

    Someone at-all information about the adapter wireless with this model, my laptop doesn't see wireless networks.

    When I go to the peripheral page he has PN533 with a yellow triangle, it says the drivers are not installed, I downloaded the drivers from the hp site, but it still does not see the wireless card? It works very well with the Ethernet cable, can not get anywhere with the troubleshooting wizards.

    Thank you

    jagnewr

    Your operating system is 8 or 8.1?

    Sorry my mistake

    Near a window of Communication of field 8

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=CH&LC=de&DLC=de&softwareitem=ob-115616-1

    Near a window Field Communication 7

    http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=CH&LC=en&DLC=en&softwareitem=ob-103277-1

  • Hosted wireless network problem

    I'm currently located in a place where the WiFi you buy will only link with one device and the IP and MAC addresses to confirm the device before you connect to the internet. I am to avoid paying for both (laptop and smartphone) devices through a wireless network but my laptop using Microsoft Virtual WiFi Miniport Adapter. However, when I start the hosted network, either through the "netsh wlan start hostednetwork" command in the command prompt or via the software free virtual router Manager, my computer freezes completely and does not respond to anything except a hard stop. When I started this, everything worked well and I could use the network hosted without any problems, but in the last few weeks, I had to shut my computer down several times a day because of this problem. Can someone help me understand why my computer keeps freezing? Any help will be greatly appreciated.

    To help you, we suggest that you try to check on the link below:

    WiFi/SoftAP virtual fails to start with "the hosted network could not be started" on Windows 7 and Windows Server 2008 R2

    An update on the result.

  • Network drives disconnect randomly on PC in Win7

    My home network consists of a router and 2 file servers with 2 external drives attached to each server.
    I have 3 PC connected to the network. Run two computer laptop XP and the third PC is a desktop computer
    running Win7.
    The XP PCs do not have this problem, only the Win7 PC.

    I applied to the difficulty of Microsoft PC Win7 it 50494.

    That he correct text States 3 items to:

    (1) I checked the registry value - \lanmanserver\parameters autodisconnect is value ffffffff.
    (2) the registry value - \lanmanworkstation\parameters value: KeepConn does not exist.  I'm not
    of course what I'd do in this regard?
    (3) I used the command net config server /autodisconnect:number to disable the automatic disconnection by setting the
    Number-1.

    Do I need help to make sure that I applied the adapt 50494 correctly and if so, why the problem still happened?

    I saw the method 1 to verify that the patch has been applied to it.  This is with the exception of
    value: KeepConn in \lanmanworkstation\parameters.  It does not exist in the
    record on the Win7 PC or exists - it in the registry on the XP PC 2.

    What should I do about it?

    I examined the method 2 and that the Working Group on the Win7 PC not found
    the name correctly.  I fixed it so now all 3 PC's have the same
    working group name (MSHOME).

    Your help is appreciated.

  • When I connect to the wireless network, it shows that I'm offline and I can't open a webpage as Google or Skype.

    Original title: network Ethernet NIC network adapter wireless network device

    I WAS USING MY COMPUTER, THEN HE WAS BLOCKED COMPLETELY, SO I HAD TO REINSTAL IT AGAIN, BUT WHEN IREINSTALIT AGAIN ONCE I STARTED TO HAVE A PROBLEM THAT IS (WHEN I CONECT TO WIRLESS AFTER 5 MIN SHOWES TI I'M OFFLINE AND I CAN'T OPEN ANY PAGE ON GOOGLE OR EVEN MY SKYPE) ALTHOUGH I AM STII ONLINE, SO I HAVE TO SWITCH IT OFF AND TURN IT BACK ON, CAN YOU HELP ME FIX IT, THANKS

    Hello

    1. what version of windows you are using on the computer?
    2. do you get any error code or error message?
    3 were there any hardware or software changes made on the computer before this problem?
     
    See the help article and check if it helps.
     
     
    Response with more information to help you.
  • Problem with IPsec VPN between ASA and router Cisco - ping is not response

    Hello

    I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):

    my network topology data:

    LAN 1 connect ASA - 1 (inside the LAN)

    PC - 10.0.1.3 255.255.255.0 10.0.1.1

    ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0

    -----------------------------------------------------------------

    ASA - 1 Connect (LAN outide) R1

    ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252

    R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252

    ---------------------------------------------------------------------

    R1 R2 to connect

    R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252

    R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252

    R2 for lan connection 2

    --------------------------------------------------------------------

    R2 to connect LAN2

    R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0

    PC - 10.0.2.3 255.255.255.0 10.0.2.1

    ASA configuration:

    1 GigabitEthernet interface
    nameif inside
    security-level 100
    IP 10.0.1.1 255.255.255.0
    no downtime
    interface GigabitEthernet 0
    nameif outside
    security-level 0
    IP 172.30.1.2 255.255.255.252
    no downtime
    Route outside 0.0.0.0 0.0.0.0 172.30.1.1

    ------------------------------------------------------------

    access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
    object obj LAN
    subnet 10.0.1.0 255.255.255.0
    object obj remote network
    10.0.2.0 subnet 255.255.255.0
    NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static

    -----------------------------------------------------------
    IKEv1 crypto policy 10
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 3600
    Crypto ikev1 allow outside
    crypto isakmp identity address

    ------------------------------------------------------------
    tunnel-group 172.30.2.2 type ipsec-l2l
    tunnel-group 172.30.2.2 ipsec-attributes
    IKEv1 pre-shared-key cisco123
    Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1

    -------------------------------------------------------------
    card crypto ASA1VPN 10 is the LAN1 to LAN2 address
    card crypto ASA1VPN 10 set peer 172.30.2.2
    card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
    card crypto ASA1VPN set 10 security-association life seconds 3600
    ASA1VPN interface card crypto outside

    R2 configuration:

    interface fastEthernet 0/0
    IP 10.0.2.1 255.255.255.0
    no downtime
    interface fastEthernet 0/1
    IP 172.30.2.2 255.255.255.252
    no downtime

    -----------------------------------------------------

    router RIP
    version 2
    Network 10.0.2.0
    network 172.30.2.0

    ------------------------------------------------------
    access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
    access-list 102 permit esp 172.30.1.2 host 172.30.2.2
    access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
    interface fastEthernet 0/1
    IP access-group 102 to

    ------------------------------------------------------
    crypto ISAKMP policy 110
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 42300

    ------------------------------------------------------
    ISAKMP crypto key cisco123 address 172.30.1.2

    -----------------------------------------------------
    Crypto ipsec transform-set esp - aes 128 R2TS

    ------------------------------------------------------

    access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255

    ------------------------------------------------------

    R2VPN 10 ipsec-isakmp crypto map
    match address 101
    defined by peer 172.30.1.2
    PFS Group1 Set
    R2TS transformation game
    86400 seconds, life of security association set
    interface fastEthernet 0/1
    card crypto R2VPN

    I don't know what the problem

    Thank you

    If the RIP is not absolutely necessary for you, try adding the default route to R2:

    IP route 0.0.0.0 0.0.0.0 172.16.2.1

    If you want to use RIP much, add permissions ACL 102:

    access-list 102 permit udp any any eq 520

  • Unable to connect to the wireless network; Request to use the function keys and the keys on the keyboard

    * Original title: wireless connection problem

    I have an Inspiron computer (laptop).  I can't connect to my wireless Internet.  When troubleshooting it says use the buttons or the function keys on the front or side of the computer to turn on my wi - fi.  How to do that? How can I activate my wireless Internet connection?  Help, please!

    Hello

    Check with Dell support, their books online, the drivers/firmware, diagnostics and ask in their forums known issues.

    Dell support
    http://support.Dell.com/

    Dell support drivers - product manual & warranty Info (left side) - and much more
    http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

    Dell forums
    http://en.community.Dell.com/forums/

    Dell PC Diagnostics
    http://www.Dell.com/support/Diagnostics/us/en/19/
    I hope this helps.
    --------------------------------------------------------------------------------------------
    Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

  • Problem with VPN compatibility between 2811 and 2911

    Hello

    I would ask anyone had problems with the implementation of a VPN tunnel between 2811 and 2911?

    The IPSec VPN is established, but for some reason, I cannot ping the side LAN across LAN to the other end of the VPN router?

    All experience would be highly appreciated

    Thank you

    IPSec VPN can be smoothly between routers cisco (and not nesesserely cisco) set up, so there should be no problem in your case.

    If you say that this tunnel is established successfully, then the problem most likely related to routing problems between sites or incorrect configured crypto-acl. Check if the hosts located on both sites have correct routing information on how to get to subnets on the other site.

    Make more accurate assumptions, it would be helpful that you provide config on both sites and describe your topology.

Maybe you are looking for

  • Why firefox doesn't save my settings?

    I just use a registry cleaner (Untiitled_ Tool Box) and now all my settings on Firefox are gone. And even if I redo my settings (homepage, modules, etc.), when I close Firefox and reopen, I am sent to the first time user page "Welcome to Firefox" and

  • Qosmio F20-153 - strange question DVD RAM

    Hello recently bought a F20-153 (PQF22E) the DVD RAM drive was a UJ-840 and had the problem of common reading and writing on discs, I have a UJ-841 replacement, but when I set up the BIOS came with the CR ROM of ERROR report. So I bought a different

  • The runtime LabVIEW 2013 silent installation

    Hello I would like to install the LV 2013 runtime silently. I tried to use the /qb cmd option to install in silent mode (setup.exe/qb), but I get the error "invalid command line parameters. However, if I use setup.exe/r (remove the final reboot) it w

  • Cannot update the 10 latest updates to the system

    When the system downloads 10 Vista software updates, it goes through all, but then, when it restarts I get a reboot error.  It cannot solve the problem, and I have to do a restore to an earlier date.  I tried several times to make the installation of

  • Updates for Windows 7 take hours even to collect the list of updates to install.

    I have a new install of Windows 7. It takes several hours just to collect the list of installed updates and many more hours to download and install those I select Install. What's wrong? It's as if there is only 1 server to support Windows 7 on Earth.