wireless network

Similar Questions

• Add a preferred wireless network

  I want to configure the wireless preferred networks on a pool of 25 computers at once while no users of the console/GUI/admin is entered, that is to say the computers are provisioned waiting on the registration screen. All computers are properly configured for access "remote management".

  I'm looking for something in Apple Remote Desktop to add some favorite wireless networks with the terminal command "networksetup" to these remote computers

  I got the terminal command:

  sudo networksetup - addpreferredwirelessnetworkatindex en0 ssid 0 wpa2 password

  Any help?

  Hi basil,

  -Something that should work can use the ARD from the Mac Admin officer, to run ssh sessions by officials of the ARD on clients, and then run the Terminal command.

  -J' used a script like this before restart locked ARD Agents on clients via ssh.  No GUI sessions running on the clients.

  The script Unix in ARD would be similar to:

  for N in 'client1.local' 'client2.local' 'clientn.local '.

  do

  {

  SSH '$N' 'sudo networksetup - addpreferredwirelessnetworkatindex en0 ssid 0 wpa2 password.

  }

  fact

  -The script is run using an adminuser which is available on each client with ssh keys setup (no password) and an entry in/etc/sudoers so the sudo command prompts nor a password.

  -L'adminuser can be activated for this task in a separate script:

  Disable: chsh s operation adminuser

  Administer enable: chsh-s/bin/bash

  hope this helps, dwbrecovery

• HOW THE AIRPORT TIME CAPSULE WIRELESS NETWORK IS PROTECTED?

  I implemented the airport Time Capsule, using a DSL modem connected to the internet as its bridge.  MacBook Pro was used for initial set up by the bolt of lightning to Ethernet connector and then disconnected and works perfectly.  Now, I would like to use Wi - Fi for my Samsung phone not iOS.  On the Samsung wireless I connect to my home network using a password.  Well, I don't think that a password was never set.  How can I configure my wifi at home to establish a password?   I don't think that the modem settings should enter in solving this for me, but I'll add that the modem required a static IP address be entered for this connection when its router features have been disabled for the connection of bridge.

  If the Time Capsule (TC) provides the wireless network, then you can secure it using AirPort Utility, as follows:

  • Run the AirPort Utility.
  • Select the TC and then, select change.
  • Select the wireless tab.
  • In the wireless security, select the type of security. I highly recommend that you choose: WPA2 Personal
  • Enter a password in the field password wireless. Enter the same password in the verify password.
  • Select Update.

  

• How better to create a wireless network

  I just moved into a property where every room has an Ethernet jack.  I intend to wire hard as many devices as I can but I also want to create a wireless network that will cover the whole of the property.

  There is no single ethernet jack which will result in only a single wireless router will cover the whole of the property.  What is the best way for me to move forward?

  I have a new time Capsule and a couple of Airport Express.  Is it possible to use the Ethernet available in each room to create a unique wireless rather than Beach which extends from the time Capsule?

  How would I do that?

  The 'best' way would be something like the following:

  • Where the Internet stream comes home, it's where the Internet modem should be located.
  • Connect a wired router only or your Time Capsule near the modem and connect it to the modem by Ethernet.
  • If this place has an Ethernet distribution panel which feeds on Ethernet wiring to the rest of the House, then connect the router or the Time Capsule to this Panel.
  • You can then place your AirPort Express base stations where you need a Wi - Fi connection by connecting to the appropriate outlet.

• How to reconfigure wireless network extended with several base stations

  I have a wifi network in an Airport Extreme wired to the modem from our Internet service provider and an Airport Express Terminal extended wireless in another part of the House. I recently added a second Airport Extreme (also extended wireless) to boost coverage in another area of the House. I want to have the Express and the extreme second each wireless connection directly to the base station to the modem to have the shortest path to the main base station, but the Airport utility network diagram seems to keep showing the network of linearly (main Extreme base - second extreme - Express). So, two questions: first, represents the schema of utility Airport the signal path real (linear Express by Extreme II, then to Extreme II/modem)?  And secondly, if so, how to reconfigure the network to have both Express and Extreme II forking the extreme base I directly, rather than having the food by Extreme II, then Extreme I Express. The network showed that the desired branched network yesterday, but today went back into the linear trajectory. I tried a simple drag and drop graphic to move the Express, thinking that surely the Apple would implement such a simple, logical and direct way to manage the network, but no. Have not seen another way to configure the network manually, so any suggestions would be appreciated.

  It is very important to understand that Apple "extend a wireless network" works on signal strength.

  In order to have the AirPort Express and AirPort Extreme to extend the network of the 'main' extreme wireless, two conditions must be fulfilled:

  (1) the AirPort Express and AirPort Extreme extension should both be on the same relative distance of the extreme 'main '.

  (2) AirPort Express and AirPort Extreme extension must both be closer to the extreme 'main' they are to each other.

  In other words, a well put together would have your "main" AirPort Extreme in the middle of the House, with a Terminal AirPort Express on one end of the House and the AirPort Extreme to the other end of the House.  In this configuration, the two airports are about the same distance from the extreme 'main'... and... "" oth extending airports are located more close to the "main" airport that they are with each other.

• Bridge mode breaks down wireless network

  I have a Time Capsule of 4th generation, I am creating an additional wifi network at the back of my house to cover a dead zone.  I'm not trying to extend an existing wifi, I seek to create a new wifi network but have it on the same network range as my network existing.

  My ISP is a router that I have in my basement that has wireless on it. .  It powers up to one router links AC that all my devices connect to.  Then, this device provides wired and wireless access to most of the House.  However, I have a task of dead at the back of the House for the wifi.  So I have an Ethernet cable, which goes to the back of the House and who connects in port WAN on the Apple Airport Extreme / Time Capsule (4th gen).   If I set this device to create a new wireless network in bridge mode, it works for about 20 minutes to an hour and then causes a sort of problem on my network and all my other devices go crazy.  If I disable the router from Apple or back to NAT, everything's fine.

  The only reason why I don't want to do this NAT device is because if I put it up to NAT then devices connected to the apple Airport extreme will have more access to the apple TV on the main network.

  So I need no more shots on why the bridge mode does not work on the router from apple or I need to know how to get Apple TV visible on two different IP ranges at the same time.  Unfortunately, the Apple TV can be connected to both wifi and wireless at the same time.

  Anyone have any ideas?

  Bridge should work fine... I would suspect that your TC gives signs of decomposition.

  It is now more than 3 years old which is the best before date.

  Try again using static IP method... I think it is more successful than the bridge.

  Should be enough information in this post... but if not just give me all the IP info from the existing modem router to. I can then give you specific info to set the TC.

  Re: time capsule Airport Guard disconnection

• Network: 2 routers Apple broadcasting separate wireless networks; one (Xfinity/Comcast) cable modem

  Hello community!  Need help, I want to use two routers to establish two separate wireless networks on a cable modem connection.  I searched for my answer and see some other threads on this topic, but all are either a bit too technical for me, are incomplete on the answers to my questions - and all seem to be locked.  I have also searched YouTube and only see videos to extend a network with two routers - not my goal.  So here is a long, but a detailed post on what I need someone help with - thank you very much in advance if anyone can all small-not me-I hope it will be useful to others in the future.

  The program installation/hardware: I have internet Comcast/Xfinity that runs to a Motorola surfboard cable modem (SB6141).  I also have two routers apple - a Time Capsule from Apple AirPort (to end 2013) and a new (2016) AirPort Extreme.

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  My plan is to have the cable modem Surfboard connect to airport Time Capsule, which will then connect to AirPort Extreme (even if it could be reverse - no difference, except that the data that I show below comes from the time Capsule, which is currently connected to the modem cable).

  To read the previous discussions, it seems that the starting point would be: modem router #1 Ethernet WAN, then a router cable #1 LAN Ethernet to the Router #2.

  First issue of clarification - the connecting cable should go to the Ethernet WAN port on the Router #2 or a LAN Ethernet port?

  Now that the first easy question is the road, I need help to configure two routers connected to allow two separate networks.  A lot of discussions about the positions of static IP addresses, cascade, etc..  I need specific help with AirPort Utility on what to change on what router.  It seems obvious that the settings under the 'Internet' and 'Network' tabs are those who need to set - the 'wireless' tabs simply treats the name of the wireless network and settings - these, at least I can understand!

  I'll organise this tabbed - here go us.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Next up, the 'Network' tab utility AirPort/window.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  If I click on the 'Network Options' button at the bottom of the window, it takes me to the "Networking Options" window Here I have areas of entry to specify the DHCP lease duration, can specify the DHCP IPv4 range, as well as part of the extended DHCP IPv4 comments.  There are checkboxes: enable NAT Port Mapping Protocol. Select the host by default (with input if selected text box); Enable the IGMP Snooping; Block incoming IPv6 connections; Allow the Teredo Tunnels; and allow inbound IPSec authentication.

  For this window, here is the current settings on the Router #1:

  DHCP lease is 1 day; Beach DHCP IPv6 is 10.1.2 to 200; Hosts IPv4 DHCP Range is 172.16.42.2 to 200.  The following check boxes are enabled/checked: enable NAT Port Mapping Protocol. Block incoming IPv6 connections; And allow inbound IPSec authentication.

  Who can help me? What parameters, if all do I need to change the #1 router?  How to set up router #2 to make a second wireless network?

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  What you really need is a combination router / Ethernet switches that s supports VLANdedicated. Given that Apple routers do not, at best, you can potentially get the results that you are looking for, but at a performance cost. In other words, you can have two separate WiFi networks where clients connected to a network can not 'see' those related to another and both routers will always provide access to the Internet through Comcast modem. Note: Arris / Motorola SB6141 isn't a gateway device. Instead, it's a simple modem. A gateway is a router modem combination.

  To do this, should do the following:

  • The Time Capsule (TC) would need to be directly connected to the modem using an Ethernet cable. This base station would remain in its default configuration of the router. In other words, the router Mode (in AirPort Utility) would establish: DHCP and NAT.
  • AirPort Extreme would be directly linked to TB by Ethernet. The cable must be connected to one of the LAN ports on the TC on the WAN port to the extreme. It must also be configured as a router. However, there are differences in the extreme:
    • Use a different name to the Wi - Fi network.
    • Use another range of IP DHCP address. By default, Apple base stations use IP addresses in the 10.0.x.x range. I suggest that you set the base station of the second on 192.168.x.x range.

  There is a major drawback with this configuration. The second base station will be in a State of "Double NAT". Although this "separating" the two networks on different subnets, this condition is not very effective and connected to this network of customers will get lower throughput performance. There is no way around it and it is not recommended.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  The two should be: DHCP.

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  These leave it as what. The TC is information of IP address of the modem. The extreme, he'll get the TC.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  These leave it as what.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Unless your ISP provides your IPv6 service, change the IPv6 configuration option to: 'Link-local only' on two base stations.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  Router mode should be: DHCP and NAT to two base stations. Ignore the DHCP reservations and Port settings for now. Let the current DHCP range for the TC. Change the DHCP range for extreme for: 192.168.1.2 a.200. At this point do not access control for each base station.

  Since you seem to need the step by step instructions or need help to understand the different terms networking, I highly recommend that you help you to become familiar with networking, specifically on Apple systems. I suggest you consider taking the e-Book to the next control: take control of your Wi - Fi Applehttps://www.takecontrolbooks.com/apple-wifi network

• can I erase the disc without any wireless networks

  I have a time capsule which is my wireless router.  I have not used for time machine because he has older backups of Mac and does not place to save my current iMac.  I can erase the disc without any wireless networks?  I do Air Port utility?

  I can erase the disc without any wireless networks?

  Yes

  I do Air Port utility?

  Yes, see the procedure below

  • Open AirPort Utility
  • Click on the image of the Time Capsule
  • Click Edit in the window that appears
  • Click the disks at the top of the next window
  • Click on clear disk
  • Choose the Quick erase option
  • Click clear

  The procedure will take only a minute or two

• How can I change the name of my wireless network?

  I use OS X 10.11.4 and utility Airport 6.3.6. I would change the name of my network and I don't know how or where to do this. And once this is done, have what I would do with my extreme and Express to continue them to work?   Any help would be appreciated. Thank you.

  Cheers, Peter

  I use OS X 10.11.4 and utility Airport 6.3.6. I would change the name of my network and I don't know how or where to do this.

  You can change the name of the network using AirPort Utility as follows:

  • Run the AirPort Utility.
  • Select the AirPort base station and then, select change.
  • Select the wireless tab.
  • The network name can be changed in the field "name of the wireless network. Enter the desired name, and select update.

• Configuration of wireless network

  I have a HP SmartTouch 600-1050.

  I am connected to the internet via cable modem BrightHouse.

  I recently acquired a Nook HD + and would like to know how to set up a wireless network.

  I have a Linksys Wireless N300 router.

  YES, the installation program should look like;

  If the cable modem, wireless router and computers are in the same room:

  Coaxial cable > Cable Modem > cable > E900 Wireless Router > cable > computer + CORNER HD + on 802.11 a/b/g/n WiFI

  If the cable modem, router wireless are in the same room and the computer is in another room:

  Coaxial cable > Cable Modem > cable > router wireless E900 + computer and NOOK HD + 802.11 a/b/g/n WiFI

  Please send Bravo

• Try to install the adapter wireless network on s5503w

  Can need help, someone tell me the solution for my problem on the Pavilion Slimline s5503w wireless network adapter?

  It has an operating system of windows 7, works in 64-bit, 3 GB of RAM, proc AMD140 to 2700 mhz. Have you tried three different suppliers of network adapters wireless Rosewill RNX-N180PCe pci Express 1, TP-Link TL WN781ND pci express 1

  and now finally, Netgear WG111v3. I just want to get the wireless desktop. I have a wireless G of Linksys WRT54G Router, D-Link print server currently works wireless. I have Zone Alarm Firewall and Avira AntiVir Personal Antivirus.

  Yes, windows update is turned on and it's all good. The problem is once the driver software is loaded, then the hardware is installed. Windows never displays the wireless network adapter on any able to pick up a wireless transmitters. The error I get is: an unexpected error has occurred.   Seek to deepen, I read that he was saying that Windows could not set the IP address.

  This would indicate that my software driver wireless network adapter did not work. Yes, I have installed internet access and it indicated on the Internet site, that the cd was the most recent driver so no additional download was necessary, use the cd to install the driver. In addition, went to the Windows 7 compatibility page and the netgear WG 111v3 that my current card is authorized for 64 bit. So, where should I go from here? Oh, yes the s5503w recognizes the hardware in the device mgr. He sees the driver software, it's like something is blocking the final stages of obtaining information IP/MAC of the wireless network adapter.

  Hello:

  I would say that there is a problem with the 3rd party firewall.

  I had the same network Netgear USB v2 card no less, and it works well with my setup of W7 64 bit on my HP PC.

  I recommend you uninstall or disable the ZoneAlarm firewall.

  W7 features of a firewall, your router WRT54G has a hardware firewall. I had one of those too, but moved to the E2000. I assume that your wireless network is secured in some way.  I think that this is your problem.

  Did you know that you can get a free antivirus/antispyware software from Microsoft that works just great?

  Here is the link:

  http://www.Microsoft.com/security/PC-security/MSE.aspx

  I think that it would cause less problems with my installation of other free software system. I have yet to be disappointed.

  Paul

• HP Photosmart C4780 connects not (wireless) on Mac or wireless network

  Sorry for the long post, but please someone help me!

  I bought my new printer a few days (actually 14th) and began to implement on my MacBook Pro with my Wi - Fi, which is routed through a Linksys router and mainly through my desktop computer (a PC with Windows XP). I used the CD that came with the printer to set it up on my Mac and it has set up the fine by USB, but when I try to set up the wireless, I get the following message:

  "Device not connected: to configure the network settings for the selected device, please connect via USB temporarily." The device can be disconnected from the USB once the network settings are transferred. »

  I reconnected and got the same message over and over again, so I decided to set up on my desktop computer instead. This does not work either and I got the same message on my desk I have on my laptop. Uninstalled on both computers, reinstalled and I STILL got the same message. At this point, I'm about to throw all the electronics in my bath tub and be done with them but on the contrary, I checked (and double checked - and triple checked) my router via my browser settings, fact that I know the SSID and the password and reconnected to the network through my laptop... Once again, the same message. I tried the network installation of push, the installation of the network PIN, I feel I have tried everything! Probably miss me something small, but eyes fresh is always an asset.

  Can someone help me? I printed a Test report of the network so that a Page Network Configuration and settings I received both... if need be, I can post the information from my router, in order to verify to implement, but after two days of trying to implement something that should have taken ten minutes (sometimes) I'm at my wits end.

  Network Test report:

  "Your HP printer cannot find your wireless router. Check our wireless router has power. Make sure that your network (SSID) HP printer name exactly matches your router (SSID) wireless network name. If they do not exactly match, run the installation of the wireless network to set up your HP printer. »

  How to change the network name of the printer to match?

  Summary of diagnosis:

  Wireless on: PASS

  Wireless work: PASS

  Find the network name (SSID): FAILURE

  Security: PASS

  The printer settings compatible with the wireless router settings: does not work

  No filtering: does not work

  Related: Does not work

  Signal strength: does not work

  Other networks detected matching your network name (SSID): does not work

  Detected wireless networks: 1

  Downlink Count: 0

  Channel: Does not work

  Although I was given my SSID (which does not match my home network - but how can I change this?) and my MAC address (I guess for the printer), so I didn't have the IP address of my printer has no way for me to get online to check all the settings! Is there another way to get this IP address?

  Summary of configuration:

  Communication mode: Infrastructure

  Authentication type: open

  Encryption: no

  ______________________________________________________________

  Network Setup page:

  General information:

  Network status: offline

  Type of connection: no

  URL to Web server integrated: http://0.0.0.0

  Firmware Version/Hostname/serial number were all given

  Admin password: not set

  802.11 wireless

  Hardware address (MAC): data

  Status: disconnected

  Port 9100

  Status: enabled

  mDNS

  Status: enabled

  Service name: Photosmart C4700 Series [6 last digits of my MAC address]

  SLP

  Status: enabled

  Microsoft Web Services

  WS discovery

  Status: enabled

  WS Print

  Status: enabled

  PC connected (s)

  Address IP/hostname: (nothing is here) Time since last access (mm: SS): (nothing is here)      

  Number of 802.11 networks discovered: 1

  (my correct information of wireless network is here, including the SSID, Mode (Infrastructure), BSSID, Channel, privacy (RSN), Auth (WPA - PSK), Encrypt (TKIP-AES), Signal and WPS (no))

  Help!

  Did you read this on your Verizon FIOS router? : http://h30434.www3.hp.com/t5/Printer-networking-and-wireless/Connection-problems-with-Verizon-FIOS-Actiontec-routers/td-p/892967

• Pavilion dv4 2123 TX: TX HP Pavilion dv4 2123 wireless network connection problems

  Machine will connect to the wireless network, but not connect to internet.

  Have restarted, hard-rebooted and uninstalled/reinstalled all the drivers for network card.

  Any help is welcome!  Thanks in advance.

  Thanks for your suggestion

  I tried link below

  HP PC - troubleshooting your wireless network and Internet access (Windows 7)

  But it does not work.

  It seems to be driver files are corrupted on my machine.

  Came to know that by running the command cmd below.

  sfc/scannow

  He metnioned that some files are not repaired. Please find the journal in the CBS.log file.

  Not sure if the driver network adaptor also get corrupted.

  Please suggest.

• Impossible to extend the AirPort Extreme wireless network

  I have a wireless network set up with a time Capsule airport 4th generation.  I'm trying to take my old AirPort Extreme wireless 3rd generation. I have double. Kettle has implemented, but I get the status message on the extreme that it cannot extend the network.  I can get a strong signal on my iPhone from the point that I have placed extreme itching so I'm close enough to the time Capsule.

  Could I use a connection by current bearer through my home wiring to the extreme and extend it like that?

  Does anyone have any suggestions?

  Please follow these steps closely and report on your results.

  Power off time Capsule airport.

  Wait 10 to 15 seconds

  Power up Time Capsule airport

  Reset the AirPort Extreme back to default factory

  Set up AirPort Extreme still extend wireless signal of the time Capsule

  Report on the results

• a6755y: a6755y wired and wireless network hard

  I already spoke with my ISP nothing helps technical support.

  I recently created my desktop computer again after having been stored for several months. Before I put it there, I was using wireless internet and local wireline connections regularly and without problem, and now I can not access to either. I have a strong connection with the modem/router device, so I thought that the issue could be in how its configuration or interpret the connection from my computer, but nothing, I have discovered has indicated that this was the case, and convenience store customer support my ISP did not find anything abnormal. I was now more confused when I discovered that it also fails to connect to another computer using a direct wired connection, even though I had in the past linked their and transfer large files regularly. I would like to assume that these issues are linked, to make the simplest solution; but as one involves a separate network adapter, and the other connects directly to the motherboard, I don't think that's likely.

  For any help or suggestion would be appreciated.

  Hi there @_GS
  
  Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.

  I understand that you pulled on your desktop, storage and now you can not connect to your wireless network.  I'm happy to help you with this problem.

  Is this the same router that you were using before you put the computer in stock?

  How is the computer to the router? (Sometimes too much signal is as bad as not enough)

  What type of cable you are using for the connection from computer to computer, you mentioned?

  There is special software required?

  Have you other wireless devices that are connected to this router without problem?

  The following pages are useful to the resolution of the problems of wireless connectivity and can help solve this problem.  Try it and tell me if it helps.
  Troubleshooting wireless network and Internet (Windows Vista)

  HP and Compaq Desktop PCs - troubleshooting your network wireless (Windows Vista)
  
  In addition, you can watch the the power management of your wireless adapter:
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.
  
  Forget a network (Windows Vista)
  1. start network and sharing Center.
  2. in the pane tasks, click on manage wireless networks.
  3. right click on the connection that you want to delete and then click on remove network.
  4. in wireless networks handle - warning dialog box, click OK.
  5. the connection is removed from the list of wireless connections that you can view or edit.
  
  Reset TCP/IP on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here, but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.
  
  Test an ethernet connection:
  Explicit. Test if the problem persists on a wired connection to the adapter hardware troubleshooting wireless can be directed to the appropriate areas.

• Qualcomm-atheros 802.11 a/b/g/n dualband wireless network module is dying

  I have a problem with the 802.11 wireless network module a/b/g/n dualband Qualcomm atheros - after a few hours of work my computer starts a fall connection for 5 to 30 seconds (I installed monitoring software). It is not question of modem or router from a connection wi - fi on my laptop works very well. I also tried turning off my Norton Insternet Security, but it does not solve the issue. Once I connected my pc to the router although eithernet past all the connection problems.

  Question: what is the good replalcement for module of qualcomm-atheros 802.11 a/b/g/n dualband wireless network? I can't figure out what model it is and qualcom seems to offer a different set of products now.

  Hello again inter9115,

  You are welcome!
  
  If this answer solved your problem, can you please mark it as an accepted solution? This will help others with the same question to find the answer they're looking for.
  
  Have a great rest of your day!