Wireless printing has stopped working, but ONLY on my G72... not on other computers on my network mobile home.

Similar Questions

• HP P1102W WIRELESS PRINTING HAS STOPPED WORKING

  Our P1102W lost the wi - fi connection and we cannot get it back.  Seems to be a printer WiFi issue.

  It is one of two HP printers (other is a 5510) using a wifi network at home (WPA2, w/password), accessible by a Dell laptop and an Apple MacBook AIr (mines).  Two computers can access the 5510.  Both lost the P1102W.

  The blue network on the P1102W is no longer regularly lights up.  By pressing the button on the P1102W wireless accomplishes nothing.  Electric bike achieves nothing (but used).  Moving the printer does not help.  P1102w works fine on USB key.

  We tried to reset the Modem and the router. No change.

  We have reinstalled the software. No change.

  We tried to run the instructions from HP to make the printer wireless using Printer HTML Config Utility, but there page does not load in Safari. (Very frustrating).

  Self test shows

  Firmwarer Datacode 20120814

  Version of the driver software = 20091104

  State of the information network not connected

  Hardware address = 00:00:00:00:00:00

  IPv4 = 0.0.0.0

  Subnet mask = 0.0.0.0

  default gateway = 0.0.0.0

  Hello name =

  802. 11 b / g wireless

  Status = active

  Comm mode = invest

  Name the network SSID = myuniquenetworkname

  = WPA/WPA2 authentication

  IP configured by = manual

  Server DHCP/BOOTP = 0.0.0.0

  0.0.0.0 WINS server

  Printing of pages = 6218 so far

  Hi @maddog8212 ,

  I see that you have lost connection with the P1102w wireless. I will definitely do my best to help you.

  I would like to reset the printer first to clear the previous network settings.
  Turn the printer off, press and hold the wireless button and cancel (x button) while turning the printer on and do not release both buttons until the printer stops making the noise.

  Print a configuration report and check the SSID address and IP are disabled.
  Print a Configuration Page.

  Plug the USB cable from the printer to the computer.

  I have provided Windows and Mac steps, you can choose how you want to set up the printer again.

  Windows as follows:

  Run the Wireless Setup to set up the printer on the network again.

  Go to start, all programs, HP, HP Laserjet P1102w, then select Wireless Network Configuration.

  Steps to configure the wireless.

  Then, unplug the USB cable.

  Test the printer.

  Mac as follows: (since you mentioned that you had the HTML option for your Mac)

  Make sure that Safari is set as default browser. (sometimes the SAP will not open if it is not set by default)

  Open Safari, at the top, select the Safari menu, select Preferences, general, as a default value.

  Close all applications.

  In the Apple menu bar, click Go, computer, MAC hard drive, library, Printers, HP, LaserJet, click the folder for your printer, click browser EWS or HTML config, it should open the webserver integrated for the printer to set up the wireless, and then click the network tab, click on wireless on the left and fill out your information. (be sure to infrastructure is selected and alpha or numeric is selected) Apply the settings.

  You should get a solid blue light on the printer in 1 minute about.

  Remove the USB driver, then add the network printer:

  Click on the Apple.
  Click on System Preferences.

  Click the printing and scanning.

  Select the printer, and then click the sign - to remove the printer. (USB driver)

  Unplug the USB cable.

  Then click on the + sign and select the printer from the list and click Add. (Hello P1102w)

  Try to print.

  If you have run Setup for the wireless again on Mac in the first place, on the Windows computer, simply create a new port.

  Go to start, devices and printers, click right on the printer and on the left, click printer properties, select the ports tab.

  Click Add Port, select the Port TCP/IP Standard, then New Port and follow the instructions in the wizard.

• The CTRL key on my macbook pro has suddenly stopped working, but only for

  Hello

  I have a Macbook Pro with Yosemite, and suddenly today the ctrl key stopped working but only when it comes to special characters, not to do a right click. I have accidentally set something off the coast, or what happened? I write a lot in Swedish on this computer (that I bought in the USA where I live too), I need these special characters, so is there an easy way to solve this problem?

  See you soon,.

  Leo

  Special characters would be the key to the default

• HP touchsmart IQ775 Wireless mouse has stopped working.

  Wireless mouse has stopped working. I have a HP Touchsmart IQ775 so I can touch the screen to navigate. did a restore of the system in SafeMode this morning and everything works fine now, but of course, it happens again. Last week, the computer did an update to quicktime which disabled, so I had to completely uninstall quicktime and the mouse immediately worked. looked but could not find that whatever this is updated overnight to re - train the problem this morning. However, the system closed and said 'power system failure driver' cannot know how to fix this, all say updated mouse drivers. is associated it with? This not computer savvy, usually google problems on my ipod touch and looking and staring at me but were not able to understand this. Thanks for all the tips

  Hello

  HP also has their own update so he could be there?

  I would stop automatic driver updates, because they are often older certified and MS is far behind.

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx
  ------------------------------------------------------

  This, to erase corruption and missing/damaged file system repair or replacement.

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Try to run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------

  Also check with HP support and forums.

  HP support
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Need help, get message display driver has stopped working, but has recovered

  Had no problems until recently, my freezer of mouse and screen, then get message display driver has stopped working, but recovered it gets really bad, please help

  Hello

  1. what operating system do you use?
  2. What is the brand and model of your system?
  3. Once you get this error message?
  4. you did it before the issue of any material changes or software?

  Try the steps outlined in the methods mentioned below and let us know if it helps.
  Note: The following Microsoft Articles are applicable for Windows 7 and Vista.

  Method 1: Boot your system in clean boot mode and temporarily disable your antivirus software. Check if get the same error message or not.

  Step 1: Try now to the KB article to perform the clean boot:
  How to troubleshoot a problem by performing a clean boot in Windows Vista and Windows 7:
  http://support.Microsoft.com/kb/929135
  Important: After you used the clean boot in order to solve your problem follow step 7 to reset the computer to start as usual.

  Clean boot in XP:

  Try now to the KB article to perform the clean boot:
  http://support.Microsoft.com/kb/310353
  Important: After you use the clean boot in order to solve your problem follow the steps in the "steps to configure Windows to use a Normal startup state" section to start your system in normal mode.

  Step 2: Turn off the antivirus software:
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  Important: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks

  Method 3: update the driver for
  

  Updated a hardware driver that is not working properly:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 4: Please visit the manufacturer's website and download the latest driver for your graphics card.

  Method 5: Windows 7 power save settings reduces the voltage to the video card too well when it is inactive for some video cards.

  To resolve this problem, disable the display (Plugged In) turn it off and turn off the display (on battery) power settings by using one of the following methods:

  Use the Group Policy settings:
  To resolve this issue by using Group Policy settings, follow these steps:

  (a) click Start, type gpedit.msc in the search box and press ENTER.

  (b) in the local Group Policy Editor, expand models of administration under Computer Configuration, expand System, expand power management, and then click display and video settings.

  (c) in the dialog box that opens, double click on turn off the display (Plugged In), click active, type 0 in the box to turn the display Off (seconds), and then click OK.

  (d) in the dialog box that opens, double click on turn off the display (on drums), click active, type 0 in the box to turn the display Off (seconds), and then click OK.

  Use the powercfg command:
  To resolve this issue by using the powercfg command, follow these steps:

  (a) click Start, type command prompt in the search box, and then click command prompt in the list of results.

  (b) at the command prompt, type the following commands:
  powercfg - X-monitor-timeout-ac 0
  powercfg - X-monitor-timeout-dc 0

  Get back to us if the problem persists.

• I use Windows XP, when I try to install 2 network connection on a PC, AAQMS has stopped working, but if I disable the secand connection quite well.

  original title: connection to a network PC 2

  I use Windows XP, when I try to install 2 network connection on a PC, AAQMS has stopped working, but if I disable the secand connection quite well.

  1 connected directly to the AAQMS system for the Air monitoring

  2. connect directly to the LAN of the company

  There is a solution that I can't connect two without any AAQMS system shutdown.

  Hello

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows XP Networking forum.

  http://social.technet.Microsoft.com/forums/en/category/windowsxpitpro

• Your wireless card has stopped working properly.

  Often, I receive this message "problem reports and solution:
  A problem with your wireless network card

  Your wireless card has stopped working properly.
  There is a network adapter that allows your computer to connect to a wireless network.
  To find out if a version update of your wireless network card is available, contact the manufacturer of your device or computer.

  Even if I get this message that I am able to connect to wireless internet. I checked on the DELL website, and according to them, I have the driver for my Inspiron 1520 then I would like to know how I can stop this annoying message that appear all the time? Is there an updated driver that I don't know?
  The problem refers to my Dell Wireless 1390 WLAN Mini-Card (Driver version 4.170.25.17)

  I would be grateful for any advice.
  Thanks in advance.

  Hi dtw1970,

  While I was researching online error message met that it is a known issue on dell computers and there are a few steps available in the dell Web site.

  Check the link and try the steps mentioned below.
  http://en.community.Dell.com/forums/p/19094058/19217044.aspx#19217044

  You can also try posting your query in the Dell Community, see the link below.
  http://en.community.Dell.com/

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP Pavilion DV6: at startup BIOS showing CPU fan has stopped working, but I checked the fan is in good condition

  Hello

  I bought my HP Pavilion dv6 laptop 2011 as it starts a is overheating, freezing windows with noisy fan sound etc... but now, on information in BIOS boot indicating that the CPU fan has stopped working so immediately, I checked that I couldn't hear any noise from fan and no symptoms as fan works so I disassembled my laptop and removed CPU cooler fan only. Simply with the help of the battery, I checked the CPU fan it is running perfectly alone. but it does not work with the laptop.

  Please help me and guide what is the cause of this problem and how to solve this problem.

  Gassab

  HI @Kartic

  Welcome to the HP Forums!

  This is a fantastic place to find answers and suggestions!
  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums Learn how Post and more

  How can I find my model number or product number?

  I understand that since you had the laptop he had an overheating problem with a loud fan noise that causes freeze it.

  Recently, you have received the message that the CPU fan has stopped working and you couldn't hear the rotation of the fan to the top.

  You have removed the fan and checked, but the fan works.  It is possible that the connection was not safe in Notepad.

  Here is a link to an overheating and Auto Shutdown problem troubleshooting.

  Have you checked for an update of the bios of your laptop. You have provided the series of laptop you have, but not the exact model, so I'm not able to check it for you.

  You can run the Wizard to help HPin order to facilitate this process.

  Like a bios update has the potential to cause damage, you can contact HP technical support using this procedure.

  Please contact our technical support at 800-474-6836. If you do not live in the United States / Canada region, please click on the link below to get a number of assistance for your region.

  World wide phone holder

  Here is a link to the guide to maintenance and Service Guide HP Pavilion dv6000 Notebook PC for your laptop.

  You can replace the thermal paste on the processor. Here is a link to a YouTube video on this process.

  How to apply thermal paste

  Good luck!

• PC-Doctor module has stopped working, but do not know if I have it on my computer...

  In the last 3-4 days I get a window intermitant arise seems them to be a "Microsoft Windows" its origin in the upper left corner of the window saying: "PC-DOCTOR MODULE has stopped working. A prolem caused the program to stop working correctly.  Windows will close the program and notify or if a solution is available. "Then a box of"close the program ".  I find 'FIND' to search for a program of the PC-DOCTOR MODULE and can not find one on my system. and "googled" it and came up with some info, but I'm not sure if it's a real source of assistance of a scam 'spyware '!   What I treat, something real, or something trying to eat me alive somehow?

  In the last 3-4 days I get a window intermitant arise seems them to be a "Microsoft Windows" its origin in the upper left corner of the window saying: "PC-DOCTOR MODULE has stopped working. A prolem caused the program to stop working correctly.  Windows will close the program and notify or if a solution is available. "Then a box of"close the program ".  I find 'FIND' to search for a program of the PC-DOCTOR MODULE and can not find one on my system. and "googled" it and came up with some info, but I'm not sure if it's a real source of assistance of a scam 'spyware '!   What I treat, something real, or something trying to eat me alive somehow?

  Hey Toccet

  to be on the good side for malware scan

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem if it is malware before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If this does not work in normal mode only the above work in SafeMode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Walter, the time zone traveller

• Wireless printer has stopped printing

  (HP4680) wireless printer suddenly stopped printing wireless.

  She can still attached USB printing another PC. Windows 7 64-bit.

  The printer wireless network Test report shows excellent connectivity and no problem.

  Try printing a test of PC printer properties page and nothing happens. Queue shows 0 items.

  Reinstalled and stopped and restarted Printer Spooler, has not been set.

  Advice appreciated.

  Problem solved.

  Stop the spooler caused properties of the printer to disappear so I could not directly print a test page.

  Since nothing else has worked so far, I did a restore of the system to 12 Nov and that fixes the problem.

  Unfortunately using Restore from know the exact cause of the problem.

  Thanks for you help.

• All of a sudden my wireless mouse has stopped working. The mouse is on and relatively new.

  Tonight my mouse (Logitech) wireless has stop working.  This happened once, and one of my friends told me to remove the receiver, shut my computer down and put the mouse back in.  However, I don't remember the exact steps he gave me.   I tried several different things, but none seems not to work.

  Hello

  What is the model number of the mouse?

  Method 1:

  I suggest you run the Microsoft fixit tool and check.

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 2:

  Support for Microsoft mouse, keyboards, LifeChat, LifeCam & more

  http://support.Microsoft.com/ph/7746

  Method 3:

  Mouse, touchpad and keyboard with Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/Mouse-touchpad-and-keyboard-problems-in-Windows?T1=Tab03

  I would suggest you also contact the Logitech support forum and check.

  http://www.Logitech.com/en-us/support

• Hello, could someone tell me how to install Photoshop, Lightroom and first? I had a subscription to Adobe and installed all three versions on my new Lenovo Erazer 510 which, unfortunately, has stopped working after only 15 days. The device

  Good evening , someone pourrait inform me How to install Photoshop, Lightroom and first? I bought a subscription Adobe and installed all three versions on my new Lenovo ERazer 510 which, unfortunately stopped working after only 15 days. Le device has been in service for forty days and I do not know How do I reinstall your applications. I tried by my Adobe account, but without results. Thank you.

  These FAQS should help you:

  FAQ: How to download and install the Adobe Creative Cloud Desktop App?

  FAQ: How to download and install creative cloud applications?

  FAQ: How to launch creative Cloud Apps

• sMy Microsoft UDB wireless mouse has stopped working. Can it be repaired or is it just did.

  My Microsoft 3000 wireless optical USB mouse has stopped working.  Can it be repaired or is it just did.

  Hello

  -Don't you make changes to your computer because of which the question began?

  I would recommend that you follow the steps in this article and see if they help.

  Troubleshoot the incidents of the response to the mouse or wireless keyboard

• my wireless mouse has stopped working

  I have two mouse Microsoft Wireless in the 3500 Series and 4000 series, I had the 4000 first order works now my 3500 has stopped working can help a whole?

  Hi Richard,

  Here are a few troubleshooting steps that you can try to solve this problem.

  
  Method 1: Run the Microsoft fixit tool and check.

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems

  If the method above does not work, proceed to the next method.

  Method 2: Refer to the suggestions for the following links.
  Troubleshoot a wireless mouse that does not correctly
  http://support.Microsoft.com/kb/321122
  
  Troubleshoot the incidents of the response to the mouse or wireless keyboard
  http://support.Microsoft.com/kb/838398

  If you have additional questions, or if this problem persists, come in and we will be happy to help you.

• Your wireless card has stopped working properly, because a compatible driver is not available for this version of Windows.

  I'm not very tech-savvy... like everything. So I have no idea what to do on this subject, but the problem is very irritating because my wireless just randomly stops working for a short period of time, and it happens quite often. Does anyone have any suggestions?

  My computer told me to go to the website of Buffalo, but I had no idea what to do from there.

  Hi Chadbassett,

  Thank you to contact the community Microsoft and we will be happy to help you with your concern.

  According to the description provided, I understand that you are facing a problem connecting to the wireless network.

  He would be grateful if you can answer this question in order to help you further.

  1. have you made changes on the computer before this problem?

  2. What is the brand and model of your computer?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Run the windows network troubleshooter, and check if it helps.

  Using the troubleshooter from network in Windows 7: http://windows.microsoft.com/en-US/windows7/Using-the-Network-troubleshooter-in-Windows-7

  Method 2:

  I suggest you to download and install the latest drivers wireless in the factory.

  Note: If the drive is not compatible with windows 7, I recommend you to install the driver software in compatibility mode and check if that helps.

  Windows 7 Compatibility Center: http://www.microsoft.com/windows/compatibility/windows-7/en-us/default.aspx

  Make older programs in this version of Windows: http://windows.microsoft.com/en-us/windows7/Make-older-programs-run-in-this-version-of-Windows

  Reference:

  Problems in Windows wireless and wired network connection: http://windows.microsoft.com/en-US/windows/help/wired-and-wireless-network-connection-problems-in-windows

  We would be more than happy to help you if the steps above did not solve the problem.