[Wireless-Vista] Disable the automatic access point.

Similar Questions

• 4402 wireless controller and the 1130AG access points

  I have a bunch of 1130AG (35) and 1231 points of access. I just bought a controller 4402 so I could handle these much easier access points. I currently have the offline access points, so I could control. With the wireless in the mix controller, that I have to fix these to light mode or can I leave them offline.

  We know not the operating instructions so I can leave them in stand-alone mode. Most of them is in the rafters in our warehuse, and I didn't have to pull of these if I have to. If I can use them offline, how can I do that?

  Thanks much for any info!

  Dave

  Hi Dave,.

  A WLC manages autonomous APs.
  So if you want to centralize the management of your APs through the WLC, you will need to convert it to light and enter them on the WLC.

  To convert the lightweight access points, you can choose between several options:

  1. thanks to a specific upgrade tool that you could install on a PC:
  http://www.Cisco.com/en/us/partner/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html

  2. [the most evolutionary] by WCS, with a model of migration that could apply to several APs:
  http://www.Cisco.com/en/us/docs/wireless/WCS/7.0/Configuration/Guide/7_0apcfg.html#wp1054876

  3. [not in any book] by the following steps:
  3 (a) download the CEC lwapp recovery image and store it on a TFTP server.
  3 (b) Telnet to the stand-alone PA and issuing the following command:
  Archive Download-sw / overwrite/reload tftp: / // [lwapp recovery image file path]

  As a general recommendation, before to convert the lightweight access points, you can be sure that the wired infrastructure behind is ready to direct them to the WLC for recording.
  It's suggestions explained in the link on the above option #1.

  Hope this helps,

  Fede

  --
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Windows 7 wireless emphasizes the connection to the wrong access point

  I use a model of wireless USB Netgear WN111 with Windows 7 64-bit adapter, connect to a D-Link wireless access point.

  Every time I have connect or wake the computer from sleep, he insists on connecting to the wrong access point - it connects to an unsecured Linksys device somewhere within the range.  I then manually connect to the correct access point - my D-Link.

  I went into the network sharing Center > manage the wireless networks and removed the network Linksys of rogue, but it always comes back.

  Any ideas or advice?

  Hello

  I don't know why he keeps picking up the 'rogue' network after that you deleted. My Windows 7 does not behave like that, and my research can reveal a way that I could do. Maybe someone else can tell you why he does. However, as a solution, you can try the following in manage wireless networks...

  1. do not remove the network of thugs, move it to the bottom of the list all the way down.

  2. open the rogue network properties and uncheck the box "connect automatically when this network is in range.

  3. open the properties of your network and check the box "connect automatically when this network is in range.

  4. you can even try to untick "connect to a more preferred network if available" both networks.

  Please mark this as useful or response if applicable.

  Tricky

• How can I reset or fix my router wireless or (lost the ability to connect wirelessly to the internet) access point

  Wireless hub works, other computers are connected

  On a laptop, I lost the ability to connect wirelessly to the internet (message: limited connectivity)

  Recommended by the system solution: reset or repair your access point or wireless router

  How can I do?

  I think that what you aim for is "power cycle".

  To do this, simply unplug the router/access point power adapter. Wait a minute. Then reconnect it.

  Hope this helps

  Post back if necessary

  ___________________

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to disable the automatic creation of folders of documents under Vista?

  How can I disable the automatic creation of folders on my desktop windows wista SP2 documents?

  Hi ZucOrc,

  (1) since when are you facing this problem?

  (2) remember to make changes?

  Method 1: Run the fixit available in the links below and check if that makes a difference-Worth to try
  Diagnose and repair Windows files and folders problems automatically
  Difficulty of broken desktop shortcuts and common system maintenance tasks

  Note: FixIt would attempt to recover bad sectors on the hard disk, in the course of this process there are chances of DATA loss from that particular area.

  Method 2: Run Microsoft Security scanner (MSS) to any threat and try to correct

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: Infected files can be deleted from your computer; There is a chance of data loss.

• How can I disable the automatic connection on Ubuntu OS Netbook

  During initialization of the machine AUTO LOGIN has been already highlighted.
  Unfortunately I only noticed that I hit the next key.

  How can I disable the automatic connection?

  I think I change the etc/gdm/gdm.conf, but would like confirmation that there is a slightly different version of Linux.

  malcolli

  Decided to give the full answer on this point Ubuntu system and it works fine.
  In a terminal, run the command: sudo/usr/sbin/gdmsetup

  This will bring up the gdm gui and there you can disable auto login and the login timed.

  malcolli

• Ordered the wrong access point!

  I thought that I had ordered a 1130ag but looks like I ordered a 1131ag LWWAP.

  Please could someone tell me what the difference between a 1130 and 1131. I understand I can load the IOS on the light AP software using a tftp server, but I do not know which exit to load on this subject. 12.3JX, 12.3JA, 12.3JEA, 12.3JEB! can anyone help please? either by the way, I am in the United Kingdom, do not know if this affects image to install. Thank you.

  Hi Paul,.

  This happens all the time, so it shouldn't be a problem :) I'm guessing that you have received this AP - AIR - LAP1131AG - x - K9 LWAPP. When you really wanted this AP - AIR-AP1131G-x-K9 Cisco IOS software. Look at the comparison;

  http://www.Cisco.com/en/us/products/ps6087/products_data_sheet0900aecd801b901c.html

  That being said, you should be good to go with 12.3 (11) JA1.

  To access Cisco Aironet to Cisco IOS version 12.3 Points (11) JA1

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b11jar1n.html

  Cisco IOS version 12.3 (11) JA1 supports 32 MB independent platforms. 16 MB platforms and platforms supported by Cisco IOS version 12.3 (8) JA and earlier versions (350, 1100, 1130, 1200 and 1230 access points and access point/bridge 1300 series) are supported by Cisco IOS version 12.3 (8) JEA1.

  Do not install a "JX" (it is a software image support to upgrade and recovery Cisco Lightweight Access Point Protocol (LWAPP));

  These release notes describe features, improvements, and caveats for Cisco IOS release 12.3 (11) JX1.

  Note: This version must be loaded on points of access to the plant or by using the lightweight stand-alone mode upgrade tool. Your access point may become unusable if you install this software without using the upgrade tool.

  http://www.Cisco.com/en/us/docs/wireless/access_point/iOS/release/notes/b311jx1.html

  Returning to standalone Access Point

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  You can convert an access point of the mode light return to autonomous mode by loading a Cisco IOS version that supports stand-alone mode (Cisco IOS release 12.3 (7) JA or earlier version). If the access point is associated with a controller, you can use the controller to load the version of Cisco IOS. If the access point is not associated with a controller, you can load the version of Cisco IOS using TFTP.

  By using a TFTP server to revert to a previous version

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  --------------------------------------------------------------------------------

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 Rename the access point image file in the folder of the TFTP server c1200-k9w7 - tar.default for a series of 1200 point, c1130-k9w7 - tar.default of access for a series of 1130 access point and c1240-k9w7 - tar.default for a series of 1240 access point.

  Step 4 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access point.

  Step 7 hold the MODE button until the status of the LED turns red (approximately 20 to 30 seconds), then release.

  Step 8 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 9 after the access point reboots, reconfigure using the GUI or the CLI.

  This doc.

  http://www.Cisco.com/en/us/products/HW/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272

  I hope this helps!

  Rob

• Windows 7 PCs are not connected to the closest access point

  Windows 7 PCs are not connected to the nearest access point.  Any ideas?

  For example:

  We have AP 1 and 2 of the AP for exaple.  They have the same SSID.  AP 2 is further with a bad signal.  AP 1 is closest with an excellent signal.  Why my laptop does not connect to the AP 1?

  You MUST use the same SSID.  I think that you misread my post.

  And Yes, a channel problem is that what I have proposed.  You can try to configure access points using the 3 discrete channels (1, 6 and 11) to minimize any overlapping units to the same channel coverage.
  At least this is the traditional way, we do it, although the automatic selection increases common and 11n 40 Mhz channels (if defined in this way) are also in.

• Disable the automatic optimizer statistics

  Hello
  
  I wanted to request user_tab_modifications track, the number of rows updated in a week. Because this view is updated automatically when the automatic optimizer statistics collects statistics, I have disabled the automatic optimizer statistics. Now, I will carry out run dbms_stats. FLUSH_DATABASE_MONITORING_INFO(); manually to get the full view with the number of rows updated.
  
  My concern here is, I get the exact number of rows updated per week of user_tab_modifications in doing this? Also, is there anything that is also updated from this point of view outside of optimizer statistics that are collected on a table.
  
  Thank you

  You might try to write a few PLSQL yourself.

  What:

  SQL> create table count_X_updates (update_count number);
  
  Table created.
  
  SQL> insert into count_X_updates values (0);
  
  1 row created.
  
  SQL> commit;
  
  Commit complete.
  
  SQL>
  SQL> create table X (col_1 varchar2(5), col_2 varchar2(5), col_3 number);
  
  Table created.
  
  SQL> insert into X values ('a','first',1);
  
  1 row created.
  
  SQL> commit;
  
  Commit complete.
  
  SQL>
  
  SQL> create or replace trigger count_x_updates_trg
    2  after update of col_1,col_2,col_3
    3  on X
    4  for each row
    5  declare prev_cnt number;
    6  begin
    7  update count_X_updates set update_count = update_count+1;
    8* end;
  SQL> /
  
  Trigger created.
  
  SQL>  update x set col_1 = 'b', col_2='secnd',col_3=2;
  
  1 row updated.
  
  SQL> commit;
  
  Commit complete.
  
  SQL> select * from count_X_updates;
  
  UPDATE_COUNT
  ------------
             1
  
  SQL>  update x set col_1 = 'c' where col_3=2;
  
  1 row updated.
  
  SQL> commit;
  
  Commit complete.
  
  SQL> select * from count_X_updates;
  
  UPDATE_COUNT
  ------------
             2
  
  SQL> select * from x;
  
  COL_1 COL_2      COL_3
  ----- ----- ----------
  c     secnd          2
  
  SQL>
  

  Note: This trigger code must be improved because
  a. several sessions could obtain the same value
  b. it introduced a serialization - several session waiting on a lock on the count_X_updates of the table line - effectively, which means that all other sessions to try to update X will wait (even if they are to be updated lines X) until each previous emits a COMMIT.

  Thus, this demo code is only to show you the PLSQL triggers. But may not be used in Production.

  Practice some PLSQL. Learn about the autonomous operations.

  Hemant K Collette

• I have disabled the automatic update, but it will however update! How to disable?

  I use version 34 and I don't want to update becase the plugins work correctly with the newer versions. I disabled the automatic updates check in preferences, but updates of firefox sometimes! It makes me very angry, I'm tired to restore my backups. What should I do to prevent the automatic update forever! I'll be able to update the program if I need!

  Mozilla Maintenance Service can be updated Firefox for you. Disabling updates of Firefox does not stop this 'service' to make updates.
  https://support.Mozilla.org/en-us/KB/what-Mozilla-maintenance-service

• How can I disable the automatic renewal of an app?

  How can I disable the automatic renewal of an application I bought?

  Applications on the MAc App Store are a time purchase only. There is no renewal.

  The app offers a renewable subscription to certain services with inside, if that is managed through the application Web site if the subscription has been activated it, or can be managed inside your Apple if that was used to activate the subscription ID.

  View, change or cancel your subscription - Apple Support

• Disable the automatic reactivation after opening of the screen

  Hello

  is it possible to disable the automatic reactivation after the idle state by opening the screen? If so, how?

  Greetings
  Mr. Auer

  Hi, Matthias

  When the laptop is in sleep or Hibernate mode after the opening of the screen for laptop wakes up automatically and display will be automatically ON.

• Disable the automatic backup in Apple applications

  How can I disable the automatic backup in the Script Editor and other Apple applications?

  I love how the captain tells us what is good for us and allows us no easy way to change things.

  AutoSave/Versions has been part of Mac OS X Lion. See these instructions. Save As will be in its normal position in all applications, and when you close the documents, you will be asked if you want to return (same result as the old do not save).

  Versions and AutoSave will always run in background for the applications that use it. You can't really turn off without disrupting some application menus, but it's been at least OS X behave more like Snow Leopard or earlier version.

• You can disable the automatically load a random number of Freecell game first starts?

  FreeCell startup in Windows 7, it automatically loads a game of chance.  I don't want it.  I ALWAYS want to choose the number of game I want to play.  Yes, I can choose the game - after - the cards are dealt, but then I have to accept defeat on the hand held before that I don't want to play.

  I want to choose the game is because I'm going sequentially through the list, game 1 to...

  Yes, is it when even disable the automatic selection, or revert to the behavior where you will be asked to each selection random or # first game? (As in previous versions)

  Duh_ug,
  Well, I'm just a casual player of Freecell, so I've never really paid attention to the stats.  However what I found is that if after the cards are dealt, if you 'Select Game' before to make some moves on in the game, it does not count as a game played or a loss.  As soon as make you any kind of move on the game, then becomes an active game and will be considered a loss\game played if you select a new game.  Try it and make sure it works correctly for you. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I disabled the automatic updates and it starts to turn itself on, W H Y?

  "WINDOWS XP HOME SP2 '!

  I have disabled the automatic update and it starts itself to spin, WHY?

  HOW DO I KILL IT?

  I want all the crud that microsoft that will come to me.

  Hi Gail,

   

  You run the computer as an administrator?

  Method 1: You can run the fixit available in the article below from the off-ramp of Windows Update and then check if it makes a difference

  How to configure and use automatic updates in Windows

  http://support.Microsoft.com/kb/306525

  Method 2: You can see the steps outlined in the article below

   

  How do I turn off the Windows Update feature in Windows XP

  http://support.Microsoft.com/kb/892894

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.
  How to back up and restore the registry in Windows

  Note: It is not recommended to disable Windows Update, automatic update, you do not have to search for updates online or worry that critical fixes for Windows might be missing from your computer. Windows automatically checks for updates for your computer.