With regard to Taredo tunnel

Yes, I called my network provider, Time Warner Cable and the tech said that they are constantly changing IP address in constand mode.  My linksys router which is connected to the cable Modem Time Warner is the material which is assigned the 192... IP xxx.  I have no problems connecting to the internet.  It's my security system Norton that I check every day which appear in the historical section of the IP address of 169.xxxxx as a pseudo WARNING tunneling interface.  Time Warner said that as you responded to me that Windows problems the 169... XXXX IP address when comes into conflict with the IP address of the router.

Everything goes well without any problems of internet connection.  Thanks for your reply.

Advertisement

Everything goes well without any problems of internet connection.  Thanks for your reply.

Do not worry.  Be happy.

You'd be happier if you dumped your Norton Security software.  (If you do, be sure to use the Norton removal tool).

You can stop reading here, but if you want more details, read on.

Your ISP - Time Warner - properly explained that it assigns you a "dynamic" IP address  This means that the IP address can change from session to session (assigned external IP address will always remain the same until you disconnect from your ISP).

Because you are using a router, however, you can never see the IP address Time Warner assigned to you unless you have to look at the page 'Status' of the utility of configuration of the Linksys router or (b) go to a Web site such as http://www.whatismyip.com/

I guess it's possible that Norton can access this address and report it, but for most people that would be superfluous.  Unless you're running a web server or otherwise need to know how to reach your computer over the Internet (for example, to access your computer at home during a trip) there is no need to know your external IP address.

If you open a command prompt window (start > run > cmd > OK) and type
ipconfig/all
You can see - among others - the local IP address that is assigned to your computer by your Linksys router.  The output will look much like this:

Ethernet connection to the Local network card:

The connection-specific DNS suffix. :
... Description: Intel(r) PRO/100 Network Connection
Physical address.... : 00-07-E9-ED-0C-47
DHCP active...: Yes
Autoconfiguration enabled...: Yes
... The IP address: 192.168.1.100
... Subnet mask: 255.255.255.0.
... Default gateway. : 192.168.1.1.
DHCP server...: 192.168.1.1.
DNS servers...: 4.2.2.3.
205.171.3.65
Lease obtained...: Wednesday, December 14, 2011 17:26:06
End of the lease...: Thursday, December 15, 2011 17:26:06

If you see an IP between 169.254.0.1 and 169.254.255.254, which is called a (APIPA) automatic private IP address and is assigned by Windows for the network card in your computer when the NETWORK adapter is configured to obtain an IP address automatically (default) and (b) the NETWORK card fails to reach the server DHCP (usually in your router) which is supposed to automatically assign this address.  It is almost always an indication of password bad wireless encryption.  This has nothing to do with a conflict with the IP address of the router.

If you see something on 'Teredo Tunneling Interface' you are most likely using Vista or Windows 7 rather than XP, but what version of Windows you have, the "Teredo Tunneling" Interface relates to IPv6 and you don't need and almost certainly not using it.  What follows is not my mother tongue, but it is accurate:

To make a long story short, this means that you have IPv6 is installed as part of your network components. Check the following;

Go to control panel and double-click on network connections. Right-click on the icon for your connection to the Local network and select properties from the menu.

On the general page of the property sheet, there is a box which should contain an entry for Microsoft TCP/IP version 6.

I won't bore you with the details, but the main thing is that most people have no need at the moment for IPv6. That said, it will not cause problems if leave you it installed on your computer. That said, uninstall IPv6 will not cause you to lose your internet connection. The entry see you for the Internet (TCP/IP) protocol is important.

If you are curious about IPv6, here is a website with more information.

IPv6 for Microsoft Windows: frequently asked Questions http://www.microsoft.com/technet/network/ipv6/ipv6faq.mspx

Tags: Windows

Similar Questions

  • I uninstalled ms taredo tunneling adapter by chance and now I have no access to the network or access to any windows system

    I uninstalled MS Taredo TUNNELING ADAPTER NOW I HAVE NO NETWORK or WINDOWS 7 to access anything help how can I solve this

    Hello

    Thanks for posting your query in Microsoft Community.

    You can try the following steps and check if it works for you:

    1. Click on start.
    2. Type Device Manager in the start search box, and then open it.
    3. Click the Action tab on top and click Add legacy hardware
      then click next and next again, he will then scan and find nothing then click on the screen after that.
      Wait a minute and you will see a list of devices appear, scroll and select network adapters and click Next, then in the left column choose Microsoft then in the right hand column scroll down and choose Microsoft Teredo Tunneling adapter, and then click Next and it will install it.
      To check simply do as it is set to show hidden devices right click on the Device Manager right click view, then show hidden devices.

    If the steps above does not work, you will need to download the driver from another computer on the flash drive and then install it on your computer.

    Hope the helps of information. Please get back with the results.

  • There is a problem with the Microsoft Teredo Tunneling adapter driver. The driver must be reinstalled.

    I notice that I need to solve problems for my computer.  The message said: there is a problem with the Microsoft Teredo Tunneling adapter driver. The driver must be installed.  One of the options is to reinstall the driver.  I tried, but it did not.  What is this adapter, and how should I do if the error message goes away?

    There is a problem with the Microsoft Teredo Tunneling adapter driver. The driver must be reinstalled.
    The device information
    Name: Microsoft Teredo Tunneling adapter
    ID: ROOT\ * TEREDO\0000
    Error code: 10
    Reinstall the device driver
    Completed
    There is a problem with the Microsoft Teredo Tunneling adapter driver. Reinstall the driver may resolve this issue.
    Problem with the PnP devices
    Detected
    There are problems with some devices PnP. Windows will take additional steps to continue troubleshooting these devices.
    It is a known problem if you have Zone alarm installed.  If you have installed remove it at least to check

    To disable Teredo tunneling 6to4 interface open an elevated command prompt and type

    netsh interface set terredo disabled state.
    To re - install
    1. Click on start.
    2. Type Device Manager in the start search box, and then open it.
    3. Click the Action tab on top and click Add legacy hardware
      then click next and next again, he will then scan and find nothing then click on the screen after that.
      Wait a minute and you will see a list of devices appear, scroll and select network adapters and click Next, then in the left column choose Microsoft then in the right hand column scroll down and choose Microsoft Teredo Tunneling adapter, and then click Next and it will install it.
      To check simply do as it is set to show hidden devices right click on the Device Manager right click view, then show hidden devices.
  • With regard to the application of Nook on the Surface RT. Is there a way to change the way that newspapers appear?

    With regard to the application of Nook on the Surface RT.  Is there a way to change the way that newspapers appear?  Like corners, they give a better way to navigate and get the overview for the different sections.

    Probably not "such what."  Next time you launch the application, make sure that the menu bar to it and see if there is a feedback icon.  You may be able to comment on what features you want and they can do just that.

  • I had Photoshop CS for a while. I use it for one purpose, which is to standardize my bronze products photos, all photos are identical with regard to the composition, lighting, backgrownd, actually, I always place the same scale of assessment pr

    I had Photoshop CS for a while. I use it for one purpose, which is to standardize my bronze products photos, all photos are identical with regard to the composition, lighting, backgrownd, actually, I always place the pillar of satisfaction even scale and then only switch products bronze... a simple task of worm. For this reason I have is no need to upgrade my old version of Photoshop. My problem is that it doesn't work anymore since Windows 10 recently installed in my PC. IO have tried to install it several times but can't. Is anyone out there help me please!

    Activation for CS is closed. Adobe provides you with a free replacement of CS2.

    Uninstall CS

    Go here: Download Adobe Acrobat 7 and Adobe Creative Suite 2 products

    Click English, download Photoshop CS2 and also copy the serial number that comes with it.

    Install CS2 and use this serial number CS2. There no need activation.

    Take your copy of the CS, it is no longer usable.

  • With regard to the previous discussion on the recent settings of the workspace page

    With regard to the post Re: recent files page , when I went back to answer, there is no way to reply to the post.  After trying the settings using the provided screenshots, page of recent files always came every time.  So the answers you have provided are not correct for my particular case.  Finally, I tried without any control in the preferences and that my custom workspace save as I wanted.  Here is how I had to define it.

    Thank you.

    cc-152.jpg

    It is doubly strange.  I just check and that the other thread is not locked and can be answered.  Someone else has a problem, you reply to this thread.

    Secondly, I turn off the settings described works for me and Photoshop opens without MRU and start work space.

    You did _uncheck_ these settings?  I like the new workspaces, so mine are checked, but it clearly says _Show_ at the beginning of each line.

  • With regard to the update of the locations of cards-oracle

    HII everyone,

    In my application, we using mapviewer, which was installed locally on our server, for map rendering and showing the locations of a client like pinball machines.

    Suppose that some places (address, City) is updated map... How mapviewer (which has been installed on our server locally) will update this site all in rendering...

    Thank you

    learner

    It depends on how you got the map features.  Mapfeatures are usually stored in the cache.  If a change in database may not appear in the card immediately.  If, however, given the characteristics of the map as a vectorlayer, then simple vector update updates map.  You should consider two options with regard to the update database process.  You can store the geometry as a function that is updated on the fly as change attributes of database, or you may use a database trigger to update the geometry when the attributes change.  Thus, using a combination of correct space architecture and mapviewer correct functions.

  • With regard to the management of exceptions in coherence

    Hello
    I use c ++ connection of consistency

    try {}
    String::handle gridHandleCache = GridCacheName;

    if(hCommCache == null) {}
    hCommCache = CacheFactory::getCache (gridHandleCache);
    }
    else {}

    "cost < <" Info: "< < GridCacheName < <" Cache already in a State of assets "< < endl;"
    }
    }
    {catch (exception::handle Vex)}

    "' cost < < ' consistency exe;
    }
    {} catch (std::exception (e)
    cost < < e.what ();
    }
    catch (...) {
    cost < < 'unknown exception ';
    }


    When the error occurred (duration or other errors), I still get an exception unname. It will never enter the Exception::Handle part of vex.

    When he calls on Wrestling (Exception::Handle vex) {.} I want to separate the duration and connection error ecpetion sepeartyely.

    Can I know what would cause / or how to handle it separately.

    What are the mistakes is possible to connect / put/get/invoke (touchprocessor). serializable cast?


    -Thank you

    Edited by: 882600 August 31, 2011 05:51

    There are several ways to achieve this. Perhaps the simplest is to simply catch Exception as std::exception const &, or one of its derivatives, then call what(). However, if you want to use the specific exception hierarchy richer consistency, you can get the equivalent of the what() result by calling getDescription()-> getCString(). With regard to the rankings largely what types of exceptions are "fatal", which would be RuntimeException and its derivatives, but the scope which it was caught in general is going to be more telling.

    Mark
    The Oracle coherence

  • with regard to the teredo tunneling adapter.

    I'm running on windows 7. My office just had re-vamped. Now I receive an error code 10. This could be to use a version of windows 8 in brains of windows 7?

    JBM

    If you're on a home network you can simply disable tunneling

    To disable tunneling

    http://blogs.msdn.com/b/richin/archive/2010/11/26/how-to-disable-Teredo-tunneling-pseudo-interface-6to4-adapter.aspx

    Open an elevated command prompt > type netsh interface terredo disabled state.

  • With regard to all MIRACAST

    Dear Sir.

    I have computer laptop dv6 7013 cl, argues, WIDI or the function active wireless display, I mean the fact function Miracast suport, I windows 8.1 I want to share my screen on samsung smart tv but my laptop does not recegnize who... grace wireless. You have any idea how to solve this problem

    Best regards

    Granite

    Hello Doberdolani,

    Unfortunately, your laptop does not support Miracast (WiDi display / wireless). It is a feature of Intel and available only in laptops with processors Intel took in charge. According to the specifications page, your laptop running an AMD processor.

    I hope that answers your question. Thanks for posting on the HP Forums.

  • Problem with the Microsoft Teredo Tunneling adapter.

    Appears in the device as Manager: Version 6.1.7600.16385 dated from 21/06/2006

    but appears in C:\\Windows\System32\drivers\tunnel.sys (properties/details) as:

    Version 6.1.7601.17514 dated 11/20/2010

    My computer cannot find the device and I can not print online.

    I don't have the authorization to fix, and I don't know how.  Is there a fix from Microsoft for this?

    Lesax

    I suspect that the printer (if earlier) has installed an older driver. I would like to uninstall in Device Manager and then restart your computer.  Windows should install the new a correctly it is unclear if the printer (since you don't tell us what it is) will work with the new driver.

  • Site VPN to IPsec with PAT through the tunnel configuration example

    Hello

    as I read a lot about vpn connections site-2-site
    and pass by PAT through it I still haven't found an example configuration for it on e ASA 55xx.

    now, I got suite facility with two locations A and B.

    192.168.0.0/24 Site has - ipsec - Site B 192.168.200.0/24
    172.16.16.0/24 Site has

    ---------------------------------------------------------------------------

    Host--> participated in IP 192.168.0.4: 192.168.0.3-> to 192.168.200.20
    Host 192.168.0.127--> participated in IP: 192.168.0.3-> to 192.168.200.20
    Host 192.168.0.129--> participated in IP: 192.168.0.3-> to 192.168.200.20
    Host 192.168.0.253--> participated in IP: 192.168.0.3-> to 192.168.200.20

    Host 172.16.16.127--> participated in IP: 192.168.0.3-> to 192.168.200.20
    Host 172.16.16.253--> participated in IP: 192.168.0.3-> to 192.168.200.20

    ---------------------------------------------------------------------------

    Now that I have guests autour within networks 172.16.16.0 like 192.168.0.0,
    witch need to access a server terminal server on the SITE b.

    As I have no influence on where and when guests pop up in my Site.
    I would like to hide them behind a single ip address to SITE B.

    If in the event that a new hosts need access, or old hosts can be deleted,
    its as simple as the ACL or conviniently inlet remove the object from the network.

    so I guess that the acl looks like this:

    ---------------------------------------------------------------------------

    access VPN-PARTICIPATED-HOSTS list allow ip 192.168.0.4 host 192.168.200.20
    VPN-PARTICIPATED-HOSTS access list permit ip host 192.168.0.127 192.168.200.20
    VPN-PARTICIPATED-HOSTS access list permit ip host 192.168.0.129 192.168.200.20
    access VPN-PARTICIPATED-HOSTS list allow ip 192.168.0.253 host 192.168.200.20
    VPN-PARTICIPATED-HOSTS access list permit ip host 172.16.16.127 192.168.200.20
    VPN-PARTICIPATED-HOSTS access list permit ip host 172.16.16.253 192.168.200.20

    ---------------------------------------------------------------------------

    But, now, my big question is, how do I said the asa to use: 192.168.0.3 as the
    address for the translation of PAT?

    something like this he will say, it must be treated according to the policy:

    NAT (1-access VPN INVOLVED-HOST internal list)

    Now how do I do that?
    The rest of the config, I guess that will be quite normal as follows:

    card crypto outside_map 1 match address outside_1_cryptomap
    card crypto outside_map 1 set of AA peers. ABM CC. DD
    card crypto outside_map 1 set of transformation-ESP-AES-256-SHA
    outside_map card crypto 1 lifetime of security set association, 3600 seconds

    permit access list extended ip 192.168.0.3 outside_1_cryptomap host 192.168.200.20

    ---------------------------------------------------------------------------

    On SITE B

    the config is pretty simple:

    card crypto outside_map 1 match address outside_1_cryptomap
    card crypto outside_map 1 set of peer SITE has IP
    card crypto outside_map 1 set of transformation-ESP-AES-256-SHA
    outside_map card crypto 1 lifetime of security set association, 3600 seconds

    outside_1_cryptomap list extended access allowed host host 192.168.200.20 IP 192.168.0.3

    inside_nat0_outbound list extended access allowed host host 192.168.200.20 IP 192.168.0.3

    ---------------------------------------------------------------------------

    Thank you for you're extra eyes and precious time!

    Colin

    You want to PAT the traffic that goes through the tunnel?

    list of access allowed PAT ip 192.168.0.0 255.255.255.0 192.168.200.0 255.255.255.0

    PAT 172.16.16.0 permit ip access list 255.255.255.0 192.168.200.0 255.255.255.0

    NAT (inside) 1 access list PAT

    Global (outside) 1 192.168.0.3 255.255.255.255

    Then, the VPN ACL applied to the card encryption:

    list of access allowed vpn host ip 192.168.0.3 192.168.200.0 255.255.255.0

    Thus, all traffic from Site A will be PATed when you remotely 192.168.200.0/24

    The interesting thing is that traffic can only be activated from your end.

    The remote end cannot initialize traffic to 192.168.0.3 if there is not a version of dynamic translation on your side.

    Is that what you are looking for?

    Federico.

  • ASA - s2s vpn with dynamic ip - Dungeon tunnel upward

    Hi guys,.

    We want to set up a vpn between our central asa5520, and a new branch office asa5505 with dynamic public ip address.

    This type of configuration is supported, but the tunnel can only be initiated from the asa distance (the asa central do not know how to reach the asa remote).

    prove that on this vpn also transit traffic voice, we must always maintain the tunnel.

    A solution would be to have a kind of continuous ping from the remote office to the central office... is more 'professional' wat to reach our goal?

    Thank you.

    Try, 'management-access to the inside' of the asa and ping

  • View of the horizon 3.5.0 and ThinApp v4.7 with Cisco ASA Smart Tunnel 9.3.3

    Hello

    The problem:

    Our technology smart tunnel doesn't seem to be forward traffic to our new customer from the view.  I wonder what kind of configuration changes must be considered to enable such a connection.  The error returned when searching for the host name goes in the direction of the hostname not found.  Error finding of intellectual property is related to the time-out.

    Background information and specifications:

    We are in the process of upgrading our servers from 5.2 to 6.2 connection.  As part of the upgrade, we want to improve our customers for the Horizon to use version 3.5.0.  To make it easier on vendors and remote computers we prefer also to our Horizon View Client with ThinApp 4.7.3 ThinApp.  We currently have a Cisco ASA, supporting a SSL VPN portal with "Smart Tunnel" technology.  The ASA is currently on firmware 9.3.3 in production, but we have access to version 9.5 in test.

    Preferred connection scenario:

    User > PC > VMware View Client (ThinApp would be) > Cisco ASA Smart Tunnel > view connection server > Virtual Office

    .exe running on the client to view ThinApp:

    It seems the ThinApp Client version view is only launching VMware - view.exe.

    .exe running from the customer view full/thickness:

    VMware - view.exe

    -ftnlsv.exe

    -vmwsprrdpwks.exe

    -ftscanmgr.exe

    There is something else to consider when the view client configuration ThinApp or thickness to work with Cisco SSL VPN Portal and the Smart Tunnel?  We should have ports configured in the client in connection with the same view Firewall works with SSL VPN Portal port redirector functionality.

    We have not been able to find any documentation on how to properly configure the smart to work with the New Horizon 3.5.2 client Tunnel.  A ticket of troubleshooting with Cisco suggests that the Smart Tunnel feature still perhaps not compatible with this new Horizon (thin or thick) client.  Currently, we are looking at other options because it is not not clear whether Cisco will be able to get us the confirmation or offer a solution without delay of our project to upgrade.  Maybe stick to the previous VMware View Client version 5.4.0 which we know work with Smart Tunnel in some situations and with the redirector port for others.

  • with regard to default

    Hello

    I have been using adobe cc for the moment some time. However, this month following the payment does not get Treaty and I received an email regarding the same. I contacted my Bank and they said that their server is down today and they had some problems with the treatment of all payments by credit card. So what am I supposed to do now? Adobe will try to process the payment again or what is the procedure?

    Please contact customer service to update payment information. You can use: http://helpx.adobe.com/x-productkb/global/phone-support-orders.html

Maybe you are looking for

  • TouchSmart N090sa 15: N090sa Wifi card upgrade

    I have a Touchsmart 15 N090sa and I was wondering if in the bios, there was a list of wireless card white I want to upgrade a newer version, as if there is a whitelist which would limit the options for many.

  • ReadyNAS 204 + WD Live

    Hello, just bought and put in place a 204 Readynas to replace an old pc I used in flow of. Put everything in place easily and copied all my multimedia elements on the nas. My problem seems to be continuous from the nas to my WD Live box. Movies or sh

  • HP ENVY 17-j010tx Notebook PC: replacement laptop battery

    HP ENVY 17-j010tx Notebook PC (ENERGY STAR) I can't do a battery of alternatives in Australia Companies that say they can do, are asking an extra $ 250.00 in application fees. more 4 weeks for delivery!

  • Problems using Bluetooth Lenovo Laser Mouse with Helix

    I'm from the Lenovo Bluetooth Laser Mouse to use with my Helix. Works well except that from time to time it just stops working and becomes completely insensitive. I can get it going again by going to settings > change PC settings > devices disconnect

  • Pavilion G4: My laptop HP Pavilion series G4 filter black

    My laptop HP Pavilion G4 series black screen Out.But when that I plugged into the other external monitor it shows everyting. The laptop not fall out or something like that that the problem would be someone please help The fan is runningand has so doe