With the help of a second domestic airport to extend the network

Similar Questions

• Windows system error: there is an IP address conflict with another system with the network. How do I remove this error message?

  I just installed a new internet provider and all of my connections are working fine, but I constantly get this "Windows system error: there is an IP address conflict with another system with the network." I have my electrician of the internet modem connected to my office. I have also two wireless devices connected to the appearance of the Modem wireless. I constantly get this error message mentioned above, and I want to get rid of it.

  This means that all that he says.  Your Windows system has an address that already exists on your local network.  Turn your system off and use a working system to locate this address and to which unit he belongs.  In most LANs, the router's DHCP server.  You may be able to ask the router which addresses are used and see what device uses this address, but I suspect not.

  Duplicate addresses can occur when two systems received the same address manually, or when we got an address in the DHCP of the router range. It is unclear when this happened because he is not in control of the address and puts the address duplicate to a second system.  You need to track down, ensuring that all addresses manually asigned are out of the DHCP range, that you book the address of the router, if you want the device to use this address, or configure all devices to request the address of the router using DHCP.

• Empty blackBerry Smartphones host routing table, will not register with the network.

  I want to apologize if I put this post in the wrong thread.

  So here's the question. I sent a request to my service provider to upgrade several SIM's have Blackberry service added to them. I asked specifically for them to make sure that the SIM card have been set to BES not BIS. The first SIM card I try to register with the network does the following for me. The phone, before I save it with the BES server can call and surf the internet. Once I have sync the phone with the company's server and I go back outside to check on her send and receive these emails, I try to control the internet and it says that the service is not available. I have 3G (Yes capitol) service and I can make phone calls. The host routing table is empty and when I try to save the phone it just says 'sent message' but I never receives the roads. I wiped the phone and repeat the steps with the same result. I contaced the carrier because all the Google search I did pointed to the carrier but they swear the correct plan is attached. Please if anyone can help me it would be greatly appreciated.

  Hello and welcome to the community!

  In fact, he should persist with the carrier. But first try to remove this BB to your BES, then by the ResetToFactory WIPE to remove the it strategy. Then run everywhere with the BB, ensuring that you can do all the activities of BIS (including filling of the HRT) before activating the BES. If it continues to fail, then you must climb the carrier and BIS get work before you activate BES.

  HRT and the functions of BIS should not be affected by BES, unless there is something in your it strategy that does. It is not very likely but it should impact the devices ALL active BES, not one only.

  Good luck!

• When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

  When I try to establish a wifi connection, it shows that the problem with the network card is not fixed. How can I solve this problem?

  Hello

  Thank you for writing to Microsoft Communities.

  Until we start troubleshooting on this issue please provides us additional information by answering a few questions, this will help us better solutions to the problems.

  1. What is the full error message do you get?

  2. are - that you be able to access or connect to the Internet via wired?

  3 have there been recent changes to the computer before the show?

  Please go ahead and follow the steps mentioned and later a update on the State of the question.

  Method 1:
  Try to run the network troubleshooters. Check if it enumerates and helps resolve the errors.
  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

  Method 2: If the problem persists, try to follow the steps from the link.

  In the Windows wireless network connection problems:
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Check this link for more information:

  How can I troubleshoot network card? http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Please follow these recommended steps and post if you still experience the problem.

• Windows Media Player cannot play the file because of a problem with the network or firewall settings.

  Windows media player cannot play the file because a prblem with the network or firewall settings, you can help me solve this problem?

  original title: windows media player

  Hello

  1. you remember to make changes to the computer before this problem?

  2. do you get this error when you try to play a specific file or all files?

  Follow these methods.
  
  Method 1: Open the troubleshooting Windows Media Player settings Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-Windows-Media-Player-settings-Troubleshooter

  Method 2: I suggest that you disable Antivirus software and firewall temporarily and check.
  Disable the antivirus software

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software Tour

  Enable or disable Windows Firewall
  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off
  Note: Firewall and antivirus to protect your computer against viruses and other security threats.  In most cases, you should not disable it.  If you have to disable it temporarily, you should reactivate as soon as you are finished.  If you are connected to the Internet or a network while the firewall and anti-virus are disabled, your computer is vulnerable to attacks.

  
  Method 3: try to change the proxy settings.

  a. open Windows Media Player, press the Alt key to bring up the file menu.

  b. click on the Tools menu and select Options. Click the network tab.

  c. Select a Protocol (HTTP and RSTP), click Configure , and then select Autodetect proxy settings or use proxy settings of the Web browser (available for HTTP protocol only). Do this for each protocol.

• Unable to connect with the network via iphone or ipad

  Unable to connect the Apple TV (2nd generation) with the network via Wi - Fi using the remote app!

  The remote application required the devices to be on the same network, and home sharing enabled on Apple TV. The physical remote control would be necessary for the installation if this has not been done already

• TCP on PC server with the network interface has 2

  If I need to create a TCP on PC server with the network interface has 2 with a different IP address, for example 192... and 172... and the IP address of the client side is 192..., is there something I need to take care.

  Any suggestion, thank you.

  No, by default the server listens on all interfaces.

• Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Hi stuckfree,

  The question you posted would be more appropriate on the TechNet Forums. I would recommend posting your request here.

  http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

• Problem with the network connection Wireless since installation of win 7.

  I ve just installed Windows 7 last week and no problems until yesterday when all of a sudden my laptop can´t to connect to my wireless network... Strange because my Iphone can't, so it seems like there is no problem with the network.
  And the funny part is that when it detects one network different, other than mine, it connects and works very well!

  I ve tried unplugging the laptop and Wi - Fi connection, but it just says that it can´t to connect to the network... He finds it, but when I click on connect it says only: No..

  What to do?

  Hi KlinzmannFussballspielerin,

  Welcome to the Microsoft Answers community.

  Before you try the procedure below, change the security settings for the firewall at various levels and check if the problem persists.

  I suggest you to update the network drivers.

  Steps to update of network driver:

  1. click on the Start button.

  2. in the search box type devmgmt.msc, and then press ENTER.

  3. Select the network device and right click on it

  4. now, select Properties.

  5. in the Properties window, on the driver tab, click Update driver.

  6. After installing the updates, restart the computer.

  For more information visit http://windows.microsoft.com/en-US/windows-vista/Finding-drivers-What-to-do-when-your-hardware-wont-work-with-Windows-Vista

  To solve your problem, try to turn on network discovery. To do this follow the steps below:

  1. Open advanced sharing settings by clicking the Start button, then Control Panel. In the search box, type network, click Network and sharing Center, and then, in the navigation pane, click on change settings for sharing advanced.

  2. click on the chevron to expand the current network profile.

  3. click turn on network discovery and then click on save changes. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  To learn more about this feature, please visit the below mentioned link:

  http://Windows.Microsoft.com/en-us/Windows7/what-is-network-discovery

  If the problem persists then I suggest you to reset the network adapter settings. Then follow the steps below

  To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

  http://support.Microsoft.com/kb/299357

  Disable the IP helpdesk:

  1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter

  2. scroll down to the IP assistance service, right-click on it and select Properties

  3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.

  4. then click on "Stop" to stop the service from running in the current session

  5. click on OK to exit the dialog box

  Disable IPv6:

  Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.

  NOTE: You should do this for each network connection.

  Disable the DHCP broadcast flag: link: http://support.microsoft.com/default.aspx/kb/928233

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756

  (How to back up and restore the registry in Windows)

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:

  1. Click Start, type regedit in the search box, and then click regedit in the list programs.

  If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

  2. Locate and then click the following registry subkey:

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}

  3. in this registry path, click the (GUID) subkey that corresponds to the network adapter that is connected to the network.

  4. on the Edit menu, point to new, and then click DWORD (32-bit) value.

  5. in the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.

  6 right-click DhcpConnEnableBcastFlagToggle, then click on modify.

  7. in the value data box, type 1 and then click OK.

  8. close the registry editor.

  By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.

  Hope this information is useful.

  Let me know if it worked.

  Thank you, and in what concerns:

  Umesh P - Microsoft Support

  Visit our http://social.answers.microsoft.com/Forums/en-US/answersfeedback/threads/ Microsoft answers feedback Forum and let us know what you think.

• It would make a difference with the network to change to Wireless Broadband?

  original title: Iam moving so I had Internet & cable t switch now I use Wireless Broadband would be - that make a difference with the network?

  Just need to know if from cable Internet broadband wireless to have an effect on my computer >

  as with the network, I know that I have to change my USB connection?

  Hi pattylopezSP,

  See these articles for more information on the wireless connection.

  5 steps: how to set up your network wireless home

  Wireless network card: frequently asked questions

  The network connection is based on the Internet (FSI) Service provider. Speed and other features depend on the tariff or package you are using. You can also contact the ISP for further assistance and information.

• Unable to connect to the internet with the NETWORK card and Windows Millennium Edition.

  Hello

  I turned on my old computer yesterday, who has installed Windows Millennium Edition. At the back of the computer is an Ethernet port which is marked as LIEN ACT. The NIC with this port is Realtek 8139 PCI Fast Internet Adapter. I spend two hours on the Internet configuration and I did and finally got connected, but then, a few hours after, something went wrong and the Internet and the NETWORK card has stopped working! And the card has disappeared from the Device Manager, but he's still showing in network in Control Panel. I opened the computer and I reconnected it to the slot, but it did not help. At the back of the computer next to this port are two LEDs - green indicates the power that lights up when I plug the Internet cable and the other orange indicates actual connection. But now these two LEDs are not indicating something even when I plugged in the cable to the Internet, which comes from my router. In the computer a Dial Up connection PCI is installed too, but I disabled it. I used Dial-Up in 2002. So, I need help.
  But I know that I can connect with this Ethernet card to the Internet because it worked for 3 hours, I've loaded the pages and downloaded programs.
  Please don't point, should I upgrade Windows!
  Thank you.

  Hi friend,
  You can try a Bing search on connectivity to Win ME, I don't know there are still a few old sites that are not taken down you will find a few FAQ on.
  I saw not a ME machine in too many years to count!
  Good luck on your adventure.
  B Eddie

• mac address of a system changes with the network?

  I was using the dongle for the internet. in the cmd prompt, I typed ipconfig-all and it run thus:

  Windows IP configuration

  Name of the host...: C00L

  Primary Dns suffix...:

  Node... type: mixed

  Active... IP routing: No.

  Active... proxy WINS: No.

  PPP adapter rel:

  The connection-specific DNS suffix. :

  ... Description: rel

  Physical address.... :

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  IPv4 address...: 115.233.36.134 (Preferred)

  ... Subnet mask: 255.255.255.255

  ... Default gateway. : 0.0.0.0.

  DNS servers...: 220.226.6.104

  220.226.100.40

  Primary WINS server...: 10.11.12.13

  Secondary WINS server...: 10.11.12.14

  NetBIOS over TCP/IP...: disabled

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Microsoft Virtual WiFi Miniport adapt

  Physical address.... : E0-2A-82-FB-76-72

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Broadcom 4313 802.11b/g/n

  Physical address.... : E0-2A-82-FB-76-72

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Description...: Realtek PCIe FE Family Controller

  Physical address.... : 98-4B-E1-9D-4B-66

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {3BFC3875-9624-4568-AB0C-1B121CAC496C}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Microsoft ISATAP adapter

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {3C55EFA0-2AD3-434C-9191-6CA183E5F21E}:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Adapter Microsoft ISATAP #2

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Description...
  . : Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Gotta show the physical addresses of networks diff diff. Wat can b the actual physical address of the pc?

  Hello

  When you use the command ipconfig with the/All option, this will bring up an address or a list of different addresses depending on whether you have a multiple network connected to your PC. If your computer has multiple network cards, the physical address of each adapter is listed separately

  Find the "card Ethernet connection to the Local network," which is your physical address/MAC address of the computer.

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• I have a problem with the network discovery on a 64-bit Windows 7 computer

  Frustrated.

  I have a windows 7 PC!  Machine 64-bit allowing network discovery stay on.  I have several posts and all the necessary services are started.  I tried toroll return the machine when he was working last but nothing is.  I tried in safe mode with networking, the same results.  Same results restarted, used a different network location, same results.  I have nothing seems to change that at all.  All the other computers on my network work fineand I can see and access the device from other computers on the local network and can tire of the broken machineBUT files, I don't see anything else on the network of this machine.  Every day, I shoot files on the network, so it is a very useful tool for me.  Tere is no antivirus running on the computer, but I did an analysis away from the machine with the trend micro software which found nothing on the machine based on a virus.  Any help would be great.

  good to have it fixed.  I think that it was a torrent that I downloaded.  Was a problem of windows firewall.  Open services.msc.  stop the windows firewall service.  Everything worked.  Went to tinyurl.com/pornofix and installed the software.  Entered into the software and some fix windows firewall and it ran.  restarted the computer and fixed.

• Photosmart C7280 will not communicate with the network. The diagnosis says that the Radio does not

  Photosmart C7280 C5582A work through a MacBook via a Mac (OS 10.5.7) wireless router was working fine last week.  Today when I tried to print, the printer was stuck in the "printing page 37%.  When I checked the Print Manager, the printer was "slowed" and since I had a lot of trouble with this printer connection before losing, I did what HP told me the last time which was to remove the printer and then recharge it.  Except that this time, once the printer has been deleted, he could not find the printer even after I restarted the wizard and reinstated the SSID and WPA many times.  I have reset the printer and the router by turning off and disconnect power provided, but he still had the same problem.  When I ran the diagnosis, he told me: 'Pass on Radio, Radio work on failure, not plugged cable Ethernet-Pass' the rest of diagnosis is "not run" and other data on diagnostic tests are the Mac addess.  The Diagnostic says the "wireless radio does not work.  Contact HP support.  Unfortunately, it's evening Sat and HP support is closed.  Any help or is this printer dead?  (I spent a fortune on ink cartridges)

  It is indeed a hardware problem then.  I'm sorry.

  I always believe that repair costs would be better put towards buying a new printer.

  However, there may be options that I'm not aware where do not have access to.  This document has some support listed options.

  However, I recommend you contact HP support at the 1-800-474-6836 (to the United States and Canada).  Phone support can provide that more than an estimate on the repair or replacement of the printer with HP and you could compare this with the cost of a new printer.

  A new printer is under warranty and most likely to be an improvement on an older printer.

• VM Compatibility ESXi 5.1 and later bad (VM version 9) with the network

  I'm having and ESXi host with 10 VM, all connected to the same portgroup on the virtual switch. To allow THT, I created the last slots with 5.1 ESXi compatibility and later (VM version 9), where all the other machines have ESXi 4.x and later (VM 7).

  Now, I'm having the issue 2 machines with version 9 can talk to each other, and version 7 cannot talk to each other. It is not possible to make a ping to a version 7 virtual machine vm version 9 and vice versa.

  
  

  An idea, a re there known issues, something I did wrong? From what I saw that day was to be a major change in the networking between these versions.

  Any help welcomed verrrrrry!

  Thank you, Philippe

  
  

  
  

  OK, after spending a day debugging, convert machines front and rear, delete and remove the NETWORK card I was able to convince the administrator to restart the host ESX - problem solved!