With the NI USB-6008 case error-200077

Similar Questions

• Generate a binary sequence with the NI USB-6008

  Hi all

  I'm new to LabView and I am trying to generate a binary sequence with a box NI USB-6008. The sequence, I'm currently generate is a counter of 5 bits, i.e. 00000 00001 00010, 00011... 11110, 11111 placing each bit in a different digital IO of the of the 6008 NOR, so that I can use the County as the bits of selection in a decoder/demux.

  I managed to simulate the binary sequence and produce a graphical interface, but I have not found how to generate the sequence of bits with the NI 6008.

  Totally, I'd appreciate any help you could provide. Thank you very much.

  Hi JosephM,

  Good Afternooon and I hope your well today.

  I just tested the code on a 6008 and also released the above code is very complex - I was for some reason any fixed on using Boolean tables.

  Please see the attached code, in LabVIEW 8.6.

  Mind you, I have configured the task as a channel for all lines. i.e. digital single I spent, is the task value should apply to all channels selected in the entry. So if you select only port0/Dev8/$line0 for example, the DAQmx driver will examine the LSB of the digital and work so $line0 must be true from the false. It will NOT update all other channels. So when I select line0:4 - it will update the first 5 lines (bits) in digital. As the code generates a number from 0-32 he emotional generates 00000 to 11111.

  

  I hope this finds you well and sorry for the first post!

• Apple Watch magnetic charging Dock is compatible with the adapter USB 12W power and if so, is the adaptor 12W shorten the charging time?

  Apple Watch magnetic charging Dock is compatible with the adapter USB 12W power and if so, is the adaptor 12W shorten the charging time?

  Yes and no.

• Satellite M30X-129 loses connectivity with the external USB device

  I have a problem with my laptop that has regularly been do worse and I can handle is no longer!

  Whenever I work with external devices via USB ports (all kinds of devices but my external hard drive Smartdisk CrossFire and my iPod in particular), after a certain period of time (sometimes minutes, sometimes hours) the laptop loses connectivity with the device.

  If happens to be listening to the music, download photos from a camera or laptop computer for the ' net or sync of the iPod, the connection is cut off, turning off the device and I have to start all over again!

  I'm almost at the point of launch of the laptop by the window, so any help is most welcome.
  Thank you
  Abderrahman

  Hello

  This happens also with the external USB mouse?
  This occurs if the power adapter is plugged or only if the laptop running on battery?

  In-hubs properties > Device Manager USB root-> power management
  You will find the option called allow the computer to turn off this device to save power.

  I would recommend the brand and disable this option.

  Maybe it helps.

  By the way; When do you update the operating system? I think that it s there long time, perhaps some system files or registry entries are corrupted or a 3rd party application affect the USB functionality?

• Error: A connection has been established with the server, but then an error occurred during the connection process.

  Hello

  I have MsSql running in the cluster environment and recently face the problem when there is a security agent installed in MsSql server, which the agent does nothing but only to capture the local database activity. The error led is as below:

  ID from step 1

  Server NIBKSQLCLUST

  Job name LSBackup_DRIB

  Newspaper log shipping backup job step name.

  Time 00:00:02

  SQL severity 0

  SQL Message ID 0

  Operator by e-mail

  Operator Net sent

  Operator paged

  Retries attempted 0

  Message

  2011-03-21 08:00:02.62 * error: could not retrieve parameters of backup for primary ID '26f46141-a676-41b2-8653-11f1b13de43a '. (Microsoft.SqlServer.Management.LogShipping) *.

  2011-03-21 08:00:02.63 * error: could not connect to the server NIBKSQLCLUST. (Microsoft.SqlServer.ConnectionInfo) *.

  2011-03-21 08:00:02.63 * error: a connection has been established with the server, but then an error occurred during the connection process. (provider: Named Pipes Provider, error: 0 - no process is on the other end of the pipe.) (.Net SqlClient data provider) *.

  2011-03-21 08:00:02.63 - END OF THE TRANSACTION LOG BACKUP-

  The process to run correctly when I turned off the security officer. Advice kindly the cause of this problem and is where all configurations should be set / changed in MsSql server.

  Thank you

  Boonlep coulibaly

  Hello

  I suggest you to send your request from the link and check.

  http://msdn.Microsoft.com/en-us/hh361695.aspx

  http://msdn.Microsoft.com/en-us/library/bb545450.aspx

• Ripple packaging error: Oh, Snap! Build request failed with the message: zip i/o error: no zip file or directory error: could not create output file

  I am trying to package and sign an application with ripple and I get this error: Oh, Snap! Build request failed with the message: zip i/o error: no zip file or directory error: could not create output file

  What can possibly be the problem here?

  Solved!

  I had the field output folder of the same value as the name of the archive

• What is wrong with this sequence, it does not work when, after 3 inserts, I add a new record with the trigger it gives an error.

  Mr President.

  What is wrong with this sequence, it does not work when, after 3 inserts, I add a new record with the trigger it gives an error.

  --SL_CUSTOMERS table data
  
  
  INSERT INTO SL_CUSTOMERS VALUES(1,'Kamrul Hasan',NULL,NULL,'Moghbazar', 'Dhaka','0456789123',NULL,NULL,NULL,'Y',NULL);
  INSERT INTO SL_CUSTOMERS VALUES(2,'Rabiul Alam',NULL,NULL,'Motijheel', 'Dhaka','0567891234',NULL,NULL,NULL,'Y',NULL);
  INSERT INTO SL_CUSTOMERS VALUES(3,'Shahed Hasan',NULL,NULL,'2-G/1,2-2,Mirpur', 'Dhaka','0678912345',NULL,NULL,NULL,'Y',NULL);
  
  
  
  

  CREATE SEQUENCE  "ALIZA"."SL_CUSTOMERS_SEQ"  MINVALUE 1 MAXVALUE 9999999999999999999999999999 INCREMENT BY 1 START WITH 1 NOCACHE NOORDER  NOCYCLE ;
  
  
  CREATE OR REPLACE TRIGGER SL_CUSTOMERS_TRG 
  BEFORE INSERT ON "ALIZA"."SL_CUSTOMERS"   
  FOR EACH ROW   
  BEGIN   
  IF :NEW.CUSTOMER_ID IS NULL OR :NEW.CUSTOMER_ID < 0 THEN  
    SELECT SL_CUSTOMERS_SEQ.nextval   
      INTO :NEW.CUSTOMER_ID  
      FROM DUAL;   
    END IF;   
  END;   
  /
  
  
  
  

  When I try to insert several records with the seq.nextval it gives error

  violation of primary key.

  INSERT INTO "ALIZA"."SL_CUSTOMERS" (CUSTOMER_NAME) VALUES ('sdfsd')
  ORA-00001: unique constraint (ALIZA.SL_CUSTOMERS_PK) violated
  ORA-06512: at line 1
  
  
  
  
  One error saving changes to table "ALIZA"."SL_CUSTOMERS":
  Row 4: ORA-00001: unique constraint (ALIZA.SL_CUSTOMERS_PK) violated
  ORA-06512: at line 1
  
  
  
  
  
  
  
  

  Concerning

  Mr President.

  I find the solution by creating a function before the triiger

  as below

  CREATE SEQUENCE  "ALIZA"."SL_CUSTOMERS_SEQ"  MINVALUE 1 MAXVALUE 9999999999999999999999999999 INCREMENT BY 1 START WITH 1 NOCACHE NOORDER  NOCYCLE ;
  
  CREATE OR REPLACE FUNCTION get_SL_CUSTOMERS_vId RETURN VARCHAR2 AS
  BEGIN
     RETURN SL_CUSTOMERS_SEQ.NEXTVAL;
  
  END;
  /
  
  CREATE OR REPLACE TRIGGER SL_CUSTOMERS_TRG
  BEFORE INSERT ON "ALIZA"."SL_CUSTOMERS"
  FOR EACH ROW
  DECLARE
  dummy VARCHAR2(200);
  BEGIN
    dummy := get_SL_CUSTOMERS_vId();
    :NEW.CUSTOMER_ID := dummy;
  END;
  /  
  

  It works very well

  Thank you all for the suggestions.

  Concerning

• What SD memory cards work in HDR-CX210? I tried 3 with the same C:13:01 error!

  What SD memory cards work in HDR-CX210? I tried 3 with the same C:13:01 error! I tried microSD with adapter sandisk sandisk SD and SONY brand SD cards. I tried to format it so and not luck.  I chose this device for use with memory cards, and he so far has not been very useful for my needs. PLEASE ADVISE!

  Hello Clark,.

  Welcome to the community of Sony.

  This error message is displayed if you use the recording medium is either not supported for use with the camcorder or the support has a problem.

  Check the link below for the memory card, you can use with your camcorder.

  http://eSupport.Sony.com/docs/dvimag/HDR-CX190_CX200_CX210_PJ200_guide/Eng/contents/03/04/02/02.html

  A formatted by a computer (Windows OS/Mac OS) memory card has no guarantee of compatibility with your camcorder.

  Power reset the camcorder.

  1. Turn off the camcorder.
  2. Remove the battery for 30 seconds and then reinsert.
  3. Finally, turn on the camcorder.

  Reset the camera by pressing the RESET button with a PIN object did during 2-3 seconds.

  If my post answered your question, please mark it as an "accepted Solution".

• plugin VMware update manager returns with "the remote server returned an error: (404) not found."

  Hello

  We have recently updated our virtual Center Server to version 4 and now when I try to download and install from the page manager plugin vmware update manager plugin is back with "the remote server returned an error: (404) not found"

  Has anyone had this problem before and eventually worked out how to fix this?

  Gregg Robertson, VCP, MCSE, MCSA, MCTS, MCITP

  You are welcome!!

• How can I improve the rate of acquisition with daqmx and usb-6008?

  Hello

  I am trying to acquire data of analog voltage with a USB-6008. I'm under Labview 8.5 student on an HP laptop with a 1.33 Ghz cpu and 736MB RAM, apparently. I tried using the Daq assistant and the low-level Daqmx functions. My best results come with a task set in MAX for my analog input, and using the function 'Daqmx read' the 'unique double 1 d sample' value in a while loop. I insert the values returned in a table which built in the while loop, and then when I'm done, I check the number of samples in the table. In the test VI attached, I also use the time to Get before and after all loop. The best sampling rate I made using this method, is around 40samples/second. I have attached a VI below that illustrates this concept. In my actual application, the data acquisition code runs at a time while loop with 1ms, parallel to other code that controls the device I'm collecting data of. The sampling rate is roughly the same for my test below VI and my application program.

  The 6008 datasheet gives the sampling frequency maximum 10 kHz. I'd be happy with 2 to 2.5 kHz, or as soon as possible; I'm sure that I can achieve a little more than 40 Hz. My first idea was tied to the hardware, but the 6008 cannot make acquisitions NI hardware.

  My question is: How can I implement a faster sampling of analog voltages to a USB-6008 in LAbview? If I can't do it, is there another way I can taste the data more quickly?

  Thank you

  -SK-

  

  To the best of my knowledge, the USB-6008 can do timed equipment acquisition. Don't forget that this is a multiplexed device, so if you add 8 channels so the maximum you can set is 10 k/8

  If you are new to LabVIEW, I suggest that you try this sample program first

  \examples\DAQmx\Analog In\Measure voltage. llb\Acq & Graph tension-Int Clk.vi

  Amit

• I get BSOD with the key USB TV Tuner PX1211E-1TVD

  Hi all

  I just bought the model tuner TV USB Toshiba px1211e-1tvd and whenever I turn it on I get a blue screen error on my hp Pavilion dv6821el pc... dv6000 series.

  I tried to update the BIOS and the driver of my pc's display, but without results...

  The USB device is properly installed and the program (savvy tv) included with the cd as well, but I still get the Blue error screen...
  The operating system is Windows Vista...

  What can you suggest me to do folks?

  Please... I need help :-(

  Hello

  The BSOD appears usually due to a hardware problem problem or software commutabilite.
  I think in your case it s a software problem and I recommend updating the driver.

  The new driver could be found on the European driver Toshiba page in the Options area.
  On the driver page choose this:

  * Options-> Office Accessories based-> tuner TV USB hybrid TV Tuner Windows Vista 32 bit *.

  There you can find Savvy TV driver.

• Acquisition of vibration with the NI USB-9234 using the NIDaqMxBase library

  I have a NI USB-9162 linked to a NOR-9234 properly configured and installed under OpenSUSE 11.3. It's the output of ldaq:

  >lsdaq
  --------------------------------
  Detecting National Instruments DAQ Devices
  Found the following DAQ Devices:
  NI USB-9234: "Dev1"    (USB0::0x3923::0x72B5::0164852A::RAW)
  --------------------------------
  

  I'm developing a simple application to acquire the values of vibration of a project connected with an accelerometer.
  We start from the example of acquireNScans - AnlgStart.c of NIDaqMxBase 3.4.5 documentation.

  Unfortunately, the program fails and generates the following error:

  "DAQmxBase Error -200428: Value passed to the Task/Channels In control is invalid."
  

  Then I realize that the NI9234 doesn't support analog and digital triggers so I have decided to try with the acquire1Scan.c (a scan without triggering):

  int main(int argc, char *argv[])
  {
      // Task parameters
      int32       error = 0;
      TaskHandle  taskHandle = 0;
      char        errBuff[2048]={'\0'};
  
      // Channel parameters
      char        chan[] = "Dev1/ai0";
      float64     min = -10.0;
      float64     max = 10.0;
  
      // Timing parameters
      uInt64      samplesPerChan = 1;
  
      // Data read parameters
      float64     data;
      int32       pointsToRead = 1;
      int32       pointsRead;
      float64     timeout = 10.0;
  
      DAQmxErrChk (DAQmxBaseCreateTask("",&taskHandle));
      DAQmxErrChk (DAQmxBaseCreateAIVoltageChan(taskHandle,chan,"",DAQmx_Val_Cfg_Default,min,max,DAQmx_Val_Volts,NULL));
      DAQmxErrChk (DAQmxBaseStartTask(taskHandle));
      DAQmxErrChk (DAQmxBaseReadAnalogF64(taskHandle,pointsToRead,timeout,DAQmx_Val_GroupByChannel,&data,samplesPerChan,&pointsRead,NULL));
  
  printf ("Acquired reading: %f\n", data);
  

  Also this program fails and gives this error:

  DAQmxBase Error -200077: Requested value is not a supported value for this property. (Timing Mode)
  

  How can I get at least a single data value of the accelerometer of the device using the NIDaqMxBase API?

  Hi giaulo,

  The examples that you have tried to run are not compatible with your device.

  The 9234 does not support analog triggering, so examples of "acquireNScans" - AnlgStart.c do not work.

  He is also unable to make an acquisition of single point because is based on the architecture of delta-sigma ADC. Here is a knowledge base article explaining the limitation:

  KB 4SU94SH7: DSA Hardware Support a Point Acquisition?

  This is the reason why the "acquire1Scan.c" does not work.

  You will need run one example making an acquisition in the buffer. "acquireNScans.c" would be a good to watch. Be aware of all these examples, the default is +/-10V input range. The 9234 can only input +/-5V, so it will take a few changes. Also as you try to read an accelerometer, IEPE excitement is probably necessary. I've attached an example which is based on the example of "contAcquireNChan.c" that defines the range and allows the excitement for the device correctly.

• Population of list for the NI USB-6008 channel

  Hello

  I use labview version 2011. I have worked with USB 6008 for two months, but I encountered an error constantly even if I restart or shutdown of the PC for a while. I connected to my channel 6008 AI0 asensor and DAQ Assistant is not populating the available analog channels. Please someone help. Since it worked fine for a month, but not today.

  History was end I solved my problem after seeing the "Error in the knowledge base" pecautions on the site of NOR. Now the help data acquisition work.

  But I wonder how MAX data are linked with these DAQ contest. Some can clear me how MAX is related with all these functions of time real Labview.

  By the way, I'm using labview for two months.

  Thank you very much.

• DAQmx also write Analog DBL 1Chan 1Samp down of released NI USB-6009 - code error-200077

  I'm trying to get 5V 0V high low output of ao0 to an NI USB-6009 based on a switch in LabVIEW using DAQmx writing Analog DBL 1Chan 1Samp.

  When you use a voltmeter connected to ao0 and analog-ground on NI USB-6009; Im not getting anything.

  I also get code error-200077 for some reason any:

  DAQmx Start Task.vi:4
  Property: AO. Max
  asked the value: 10.0
  Valid values begin with: 0.0
  End with valid values: 5.0

  Channel name: Ao0/Dev1

  The task name: _unnamedTask<28425>

  Set the configuration output terminal to the CSR instead of by default.

  Five maximum value and the minimum value to zero.

  See attachment.

• Software AIO with the only USB 3.0 systems problems

  I just had problems with the installation of PSC 1510 and J5780 to be connected systems USB 3.0 only as a Fujitsu Lifebook A544 under W7 - 64.

  In both cases, download the latest package and stopped installation:

  http://www.Club-PAC.de/download/HPj5780-error.PDF%C2%A0

  W7-64 systems are fully patched, a "naked" before first Installation HP look so no HP software - lay before.

  Note: alle USB3.0 ports are in good condition!

  Reference:

  http://h30492.www3.HP.com/T5/Drucker-und-all-in-one-GER%C3%A4te-installation-und/installation-Softwa...

  http://h30492.www3.HP.com/T5/Drucker-und-all-in-one-GER%C3%A4te-installation-und/HP-J5780-keine-Inst...

  Solution (at least for Fujitsu of A544):

  If possible, use BIOS routines disable the functionality of USB 3.0 and USB 2.0 only instead.

  Windows will then take some time to install drivers for USB for USB 2.0 devices, but after that, the HP AIO software installation will succeed.

  Now, you can reactivate the USB 3.0 feature in the BIOS. Believe it or not, software, printer, scanner still doesn't work.

  Add on: evidence for quality control: using scanner in German will have Dutch expression on the button "Cancel"...