Wrong language loaded the new Satellite C660 - 2DL

Similar Questions

• Re: Time to build some Initial on the new Satellite C660-220

  Hello

  Just bought a Satellite C660-220 with Windows 7 pre-installed.
  Confirmation of load on and followed the language and operating system but nothing has changed for half an hour or more.
  How long can I wait for the original version to take?

  Thank you
  Ralph

  Hello Ralph

  When you start the laptop for the first time recovery image must be installed first. It can take up to 2 hours. I know it may seem stupid now, but all the drivers, tools, utilities and additional software included in the recovery image must be installed and configured.

  It will happen automatically. Please note: gift of installation of image recovery t interrupt.

• Windows 7 does not start on the new Satellite C660-195

  Hello

  I just bought a Toshiba Satellite C660-195 with Windows 7 pre-installed.

  This morning I turned on it and it came with a black box with x:windows\system32\drvload.exe in it. This box then disappeared and Startup Repair kicked. He then told me that Startup Repair cannot repair this computer automatically. The notice were to remove any device that had recently been attached to the laptop (such as a webcam or music device) but I did not install a hardware or devices. I clicked finish and stop you the laptop.

  I lit it again and it's the same thing (new!)

  A forum would suggest trying the following: click on the link 'Show advanced options of the system and support recovery' who asked me to choose the configuration of my keyboard, but then when I do & click then it tells me "you must register to access system recovery options" I am never given the option connect!

  When using the F8 advanced boot options I'm still not able to solve this problem. The same thing (see above) that happens when I try to start in all security modes, last good known Configuration (Advanced), debug mode, start Windows normally etc. I don't understand it.

  Looking for other forums, they suggested dΘplaτant zero while running and then one selects Windows 7 to restore the laptop to its factory settings, but the same thing happens - it shows just the black screen with x:windows\system32\drvload.exe launched then startup repair, that does not solve the problem.

  I don't have a disc of windows 7 to restore since I only bought the laptop 6 days ago and didn't have time to do a still. In addition, the laptop must have the restoration on his hard drive, but I can't access it to restore windows.

  I'm just a home user understand all technical talk. Please can someone help me?

  Hello

  Sorry to hear you I have this problem. The fact is that the new laptops come with only HARD drive recovery image and not with recovery DVDs. What you can try now is to install the recovery image using HARD drive recovery facility.
  If this works you need out of the box again.

  Please do it following the instructions in this document - http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm

  Please send us comments.

• Cannot use my printer on a new Satellite C660 - 21Q suite

  new Satellite C660 - 21Q wanted to use my Lexmark 4600 priter obviously.
  but I told myself at the bottom of the support microsoft. NET framework V.2.0
  did; then RUN; everything goes well until 'Wizard' says 'impossible to run on a system 64-bit'
  WHAT I can't use my printer on a new pc suite?

  also downloaded thought framework 4.0 patch most recent would be useful. He did not. even after it ran ok

  Help

  I just searched lexmark 4600 Windows7 64 problem and the solution in 2009/10 is cj4600Win7en64.exe downloaded from lexmark BUT I couldn't find it. Have you looked at the printer properties in Device Manager and tried looking for an updated driver?

  The only other suggestion, I've got is open programs and features in Control Panel and click on turn windows features on or off. In the window that opens 1) read the text re filled and checked 2 boxes) at the entrance to .net and click sur-pour develop it can be helpful to turn on WCF. I know nothing else to facilitate the 'communications' and you have a multifunction printer.

  The only suggestion another and another - has your laptop downloaded all updates of W7?

• Error code 101-752 dotnet framework error, problems to load the new software of the printer

  Error code 101-752 dotnet framework error, problems to load the new software of the printer

  Hello

  (1) have you made changes before the start of this issue?

  (2) when you get the error message?

  (3) is the specific question of the installation of the printer software?

  (4) what is the brand and model of the printer?

  It seems that you need to fix .net Framework installed on the computer. Follow this link and see if it helps.

  Fix the .net Framework installation

  http://support.Microsoft.com/kb/976982/en-us

  Note: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756 /) how to back up and restore the registry in Windows

  See also:

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Let us know if that helps.

• When you change the language in the new version of legacy? Thank you

  When you change the language in the new version of legacy? Thank you

  Change the preferred language in the creative cloud desktop application and let it reinstall the programs in the new language.

  Mylenium

• I cannot load the new 5.3 LR

  I cannot load the new 5.3 LR with the 1642 error msg?

  Exit Code: 7 Please see specific errors below for troubleshooting. For example,  ERROR:   -------------------------------------- Summary --------------------------------------  - 0 fatal error(s), 2 error(s)    ----------- Payload: Adobe Photoshop Lightroom 5 5.3.0.0 Adobe_Lightroom_x64.msi_5.3 -----------  ERROR: Install MSI payload failed with error: 1624 - Error applying transforms. Verify that the specified transform paths are valid. MSI Error message:  ERROR: Third party payload installer Adobe_Lightroom_x64.msi failed with exit code: 1624  ------------------------------------------------------------------------------------- 

  Hi Blecho,

  You get the same results if you download the update 5.3 directly from here? Lightroom 5.3 now available:http://blogs.adobe.com/lightroomjournal/2013/12/lightroom-5-3-now-avai lable.html

  Let me know how it goes.

  See you soon

  LP

• Webcam is blurry on the brand-new Satellite C660

  I just bought my Satellite C660 Saturday and have just opened the webcam for the first time.
  It is REALLY blurry. I can't seem to find an option in the settings to fix, and I gave him a towel to check that it was not just dirty.

  I read the posts about the different lights that can affect the quality of the image, but I just tested it out in the different lights and it did make a difference.

  Can someone give me advice! I'm not really a techno person and I really want the webcam to work so I can use Skype!
  Thank you

  Did you remove sticker protector of the cam?

• Cannot load Windows 7 - Satellite C660 guard freezing

  Hello world.

  This is a biggy. I have a Toshiba AMD Vision Satellite C660 / C660D laptop without Windows installation disc. Last week, it has become very slow, the interface resembles that of the interface of safe mode, then finally, he became completely unresponsive, therefore, through F8 on start-up I selected the option to return to the factory settings (I have this option)

  The BACK screen appeared and started normal loading then who responded, then I rebooted only to see Windows starts for the first time and carry the load, before that I had to create a cd boot from my other laptop to reboot the system that I had lost the boot mngr.

  The last part of the installation process begins whereby a white Toshiba screen appears with a green progress bar which is responsible for some drivers (see attachment). There are 39 steps to this process and I remember before the computer should keep restart itself, but it keeps freezing after about two steps. I kept turning it off and eventually the locked system administrator accounts.

  Once more, I restarted the PC, but this time in safe mode, the operating system did in fact load in safe mode and I created a few new accounts with administrator privileges, however, I still cannot load all of the operating system because it keeps freezing during the last part of the process.

  I have very limited knowledge of loading operating systems, so any help would be greatly appreciated.

  Hello

  First of all, it was a big mistake NOT to create a recovery disk Toshiba.
  The recovery of HARD drive that you were able to start pressing F8, is only possible if the HARD drive is not defective.
  I think in your case I think that there is something wrong with the HARD drive because there was a Bishop of startup notification which means that this laptop can not find a boot manager to boot the system.

  I have no other idea about trying to reinstall the system using the Toshiba Recovery disk or another drive in Windows 7 (of course if you have one)
  If the recovery fails, you will need to investigate on how much material could be affected. I think in this case it of needed to start with HARD disk check.
  Possibly the HARD drive needs to be replaced. Of course it is possible that I m wrong part is affected, but at the first step you should check the new installation of the OS.

  A recovery disc can be ordered here:
  http://backupmedia.Toshiba.EU/landing.aspx

• Re: New Satellite C660 blocked by password

  I know this will sound silly. but I'm an ODP buy my first computer (for the wife at Christmas) and I don't have any idea what I'm doing. We bought a Toshiba Satellite C660 - 28 tons Saturday

  During installation, it asked my wife to give it a name who did and she did also a password. She has set up ok and was able to access the internet, etc.. Later, she turned off and concluded that she could not use it again. When she starts the computer name is ok, but when asked for a password, the password chosen does not work. We have tried everything, every variation of his password etc etc and cannot enter into the computer again

  What can we do? our password does not work, and we do not know how to enter a new. Can someone help or advise what we can do? We have even not yet guaranteed. Thanks a lot if you can help.

  Try this first.
  Turn on the laptop and then press and hold F8. A screen should open with different options, using the arrow cursor / keys select "safe mode with networking". I hope that you will get a login with 'Administrator' as one of the users screen and if you select this account, and there will be no password. I suggest that you use "help and Support" of the Start button to see how you reset the password.

  If you now have your machine backward, I suggest that you look at the creation of a password reset disk.

  If you still cannot come back in the machine and then if you create backup discs, then you can restore the machine out of the box with them State

• Question of battery charge on the new Satellite C50t-A-10J

  I have a new Satellite C50t-A-10J that has intermittent load problems. Sometimes it charges ok sometimes it says connected does not support. When no current charging if I click on the battery icon supported starts and continues ok.

  Does anyone know of a more automatic solution? I read on similar problem solved by uninstalling and then reinstalling the Microsoft ACPI battery compatible control method in Device Manager but is reluctant to try because the computer is new.

  I can of course go back to the retailer, but thought I'd post just in case someone had a similar solution.

  Thank you

  Hi Geoff

  I guess this isn't problem in the system.
  It seems that your battery is defective and I recommend to contact the Toshiba authorized service provider in your country to get a battery replacement.

  Welcome them

• WIFI problem with all new Satellite C660

  Hello

  I just bought a new Toshiba Satellite C660-108, I found it won t pick up and hold the wireless, I returned to the store and they replaced, but same thing happened.

  It works when I plug on-line.

  Can you please explain exactly what you mean with he won t pick up and hold the wireless?

  Can you use WLAN or not?
  Have you tested with other wireless LANs?
  Have you tried to reboot your router, check the settings and try again?

• How can I change the language on the news application?

  MY aunt wants to read the news, but she is from Mexico and speaks only Spanish. Is it possible for me to be able to change the language so that it can understand the news?

  I think that it is still only in English.

• refuse to load the new homepage at startup (Windows 7)

  After the recent updates, the browser refuses to load a new homepage at startup. It "remembers" the old address, always. Probably he did not record line after the change even though he seems to have this session. Therefore, when opens again, he returns to the old address of the home page. See you soon.

  Hi yuenct,

  You should take a look at the Knowledge Base How to set the home pagearticle.

  There are the steps in this article to reset your preferences on the default home page. I would try everything first to clear all strangeness. If it works, you can try to set your homepage again to your personal preferences.

  If this does not work, you should look the article How to fix preferences that will not save.

  Hope this helps!

• Only the C partition on the new Satellite C50-B-14Z

  Hello

  I'm not an experienced user, but I'll do my best to explain the problem.

  I bought Toshiba Satellite C50-B-14Z with 8.1 installed Windows, and when starting the system, I noticed that there is only one partition of hard drive, the C partition. When you enter the disk management, I see there are 4 basic partitions already (500 GB disk):

  -Recovery - 1 GB
  -EFI system - 100 MB
  -Recovery - 10.97 GB
  -C (boot, page file, crash dump, primary partition) - 453,57 GB

  They are all primary partitions, and I read on the forums that you can have only 4 those primary, so I can't add one more to the D partition, I would like to have.
  Possibility that I offered in "actions" is to create a virtual hard drive, but I guess that is not the same thing.
  I also read that you can create new partition if you have "unallocated" space (partition), but all 4 before indicated are those primary and not affected.

  Then, the next opportunity that I read on is to do a right-click on C and "reduce volume", and then create new partition from the rest of the space (if I understand it is good), but then I read in Windows Help:
  "When you shrink a partition, all regular files are automatically transferred to the disk to create the new unallocated space. There is no need to reformat the drive to shrink the partition. » ... "If the partition is a raw partition (that is, a lack of a file system) that contains data (for example, a database file)", reducing the partition may destroy the data. ""

  Normally, I have never tested a large part with the C partition, and now I don't know if I would destroy some system files while doing this "shrinkage" and I don't have the CD installation for the system, so I can't fix it if I ruin something.

  Please advise...

  Posted by just
  

  [So the next opportunity I haven't read is to do a right-click on C and "reduce volume", and then create new partition from the rest of the space (if I understand it right), FONTS] [/ COLOR]

  Yes, this is the right way to have more than one partition. You can define what capacity should partition C and any free space can be "convert" to the D partition.

  One last thing: don't forget to create a recovery (DVD or USB) media. It is very important to have recovery image back-up.