WRT150N questions, Please help!

So I just moved into my new House and set up my internet. I used my router before without any problem so far. So my problem is that I have this linksys router and a motorola 2210 dsl modem AT & T Eh well, if I run the Ethernet directly from the modem to the computer internet works fine. But once I added the router I can not get a connection. With the connected router, I have all green in all areas on the modem and the router "I should be connected by saying" my wireless devices are showing my hense network I should be able to connect to it. But it always says connection failed... At one point, I even had my office that I was connected to 54 Mbps but still my home page would not load. I have no idea whats wrong. The internet is coming through, my wirelss peripheral are picking up that I have a network but I can not connect unless I'm jacked right at the source. Please help me understand this. (and Yes, everything is pluged in the right way)

AT & T usually configures their Motorola 2210 to the PPPoE connection for you and use the 192.168.1.x subnet.   With its default settings, your WRT150N also tries to use the 192.168.1.x subnet.  But you can't put the same subnet on the Internet (WAN) and the ports LAN of the WRT150N.  It will be, or does not work at all it will not work properly.

To fix the problem do the following:

(1) put your entire network.

(2) disconnect all other devices WRT150N.

(3) use of an ethernet cable, the son a computer to one of the four ports LAN on the WRT150N.

(4) turn on the WRT150N and your computer.

(5) connect to WRT150N to 192.168.1.1

(6) in the WRT150N, replace the "local IP address" 192.168.2.1

7) click the 'Save Settings' button and then wait for the screen refresh (3 to 60 seconds).  You will be probably disconnected from the WRT150N.  Don't worry about this.

Exit 8) your browser and put your entire network

(9) with an ethernet cable, connect the ethernet port on the Motorola 2210 to the Internet of the WRT150N port.  Leave your computer connected to a LAN of the WRT150N port.

(10) power of your network.  It should work.

Tags: Linksys Routers

Similar Questions

  • My ID apple has been disabled and I can't restore it because I forgot my security question, please help

    My ID apple has been disabled and I can't restore it because I forgot my security question, please help

    I can't update my iphone because it will need for my apple for activation ID. Please help me.

    Contact Apple for assistance with the security of the Apple ID - Apple Support accounts

  • Touch pad questions, please help.

    Laptop HP Pavilion

    Model: 15-n096sa

    Product: F4T58EA #ABU

    OS: Windows 8.1 Home Premium X 64

    I installed Windows 8.1 Home Premium X 64 on my laptop last week, he had originally version 8 is installed when I bought a month ago. Since the upgrade of the OS of my touchpad is no longer allows me to scroll with two fingers or enlarge the pages, use the right click function by tapping with two fingers & also bring up the options in a Sling. All I can do now is to move the pointer and click or double-click with the pad.

    Can someone please help me solve this problem because it drives me crazy?

    Thanks in advance.

    Hello EnergySyndicate,

    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

    I understand that you are having problems with certain features of the touch pad doesn't work does not correctly. I think it's a question of settings. I'm you provide a HP support document: use and troubleshooting of the TouchPad and ClickPad (Windows 8) that will guide you in how to adjust settings and ensure that the common gestures of the Touchpad is correctly configured.

    I think that this will solve your problem of Touchpad and allow you to go back to listening to your computer. Thanks for posting on the HP Forums. Have a great day!

  • Facial recognition technology Optimus for T410 questions - please help

    Hi guys, I bought a T410 with NVS 310 graphics card and built-in webcam. Although the battery 9 cells works really well, I always like to save more power using the integrated graphics card Intel in light load. It's supposed to be done using NVIDIA Optimus but I can't ' find it anywhere or how to activate it. Some have said depends on pilots and I did not try that again. Please help for a long time.

    The next question is the software of face recognition, as my friend's Asus laptop has Smartlogon using face. I really enjoy doing on my T but I searched a lot of places and can't find it. I knew he had formerly VeriFace which seems to have stopped developing for Thinkpad. If anyone has this software, please give me the link.

    And once I found a problem with a device called Lexmark X 422, windows 7 reports that it may not start (code 10), I try the new driver and still no use. I have disable (uninstall) it can restore the entire system and now I can't find it in device manager to try to fix it again. My question is what is this device and how to correct these problems?

    Thank you, T rocks!

    Hi and welcome to the forum!

    To Optimus, take a look:- http://support.lenovo.com/hk/en/HintsandTips/hints_show_12832190176531.html

    Lexmark X 422 was probably your webcam, there is no need to do anything if the machine works fine now.

    Not sure on the recognition of faces, as far as I know there not this feature for ThinkPad.

    I hope this helps.

  • go mini questions please help!

    When I turn on my HP mini computer her talk me to "enter the current password" and after three trys it says "system error fatal vaulted password control failure" with code "CNU9475MH7" Please help me through this form as soon as POSSIBLE. I need the important information on this computer!

    Try to ally.

    e9lovxq4zx

    3rd letter tiny L.

    4th letter lowercase O.

    7th letter lowercase Q.

    Use this code to go into the BIOS.

    Disable all passwords that are enabled.

    IF demand for CURRENT password using this code.

    REQUEST NEW password just press ENTER.

    If asked to hit just to CHECK password to enter.

    Save and exit.

    REO

    I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

  • GANYMEDE + question: Please help

    Dear all,

    It is with regard to Ganymede +. I have configured Ganymede + on switch cisco, but it is local user name and password

    for authentication.

    With below configuration on the other switch, works very well with Ganymede + username and password, but not with

    This switch.

    AAA new-model

    AAA authentication login default group Ganymede + local

    AAA authentication login no_login local

    AAA accounting send stop-record an authentication failure

    AAA accounting exec default start-stop Ganymede group.

    orders accounting AAA 15 by default start-stop Ganymede group.

    Default connection accounting AAA power Ganymede group.

    AAA - the id of the joint session

    RADIUS-server host 10.0.2.193 touches 110A101614425A5E57 7

    RADIUS-server application made

    username admin privilege 15 password *.

    line vty 0 4

    transport input telnet ssh

    by default the authentication of connection

    Also, this switch is configured for intervlan routing, with the following configuration and I added 10.0.6.1 address IP Cisco ACS.

    interface Vlan5

    the IP 10.0.0.1 255.255.255.0

    !

    interface Vlan20

    IP 10.0.2.1 255.255.255.0

    IP helper 10.0.0.7

    !

    interface Vlan60

    IP 10.0.6.1 255.255.255.0

    REFLXIS_PUNCORE #show Ganymede

    GANYMEDE + server: 10.0.2.193/49

    Opening of socket: 33

    Firm grip: 33

    Write-offs of socket: 0

    Socket errors: 0

    Socket timeouts: 0

    Failed connection attempts: 0

    Total packets sent: 33

    Recv packets total: 0

    So please help on the same.

    Hello Eve,.

    the IP address of the server 10.0.2.193 is accessible in 20 Vlan.

    Therefore, the switch will try to connect to the server using the address IP of Vlan20, 10.0.2.1.

    You can fix this in two ways:

    1. change the configuration on the radius server to have an entry with 10.0.2.1 instead of 10.0.6.1.

    or

    2. change the configuration of the switch, adding "ip radius-server source interface vlan 60.

    Please indicate the so useful post

    Marco

  • DELL INSPIRON N4010 WEBCAM QUESTIONS: PLEASE HELP... DELL CUSTOMER... AND ANYONE WHO HAS KNOWLEDGE REGARDING MY PROBLEMS...

    I have a Dell Inspiron N4010. Configuration: 1st generation i5 processor with windows 7 home basic 64-bit.

    3 months after the purchase of my laptop, I have updated my Dell webcam central through the applications update service... Shortly after the update, my integrated webcam has started to show problems.

    DESCRIPTION OF THE PROBLEM:

    Shortly after the update of my installed factory Dell webcam central, my integrated webcam has begun to show the problem. webcam was able to start with any application such as Skype or dell central webcam himself. Instead, webcam LED flashes for flicker of a second, and then goes away without any streaming video.  Trying to open it, an error message is displayed: "your webcam can be used by another application. Close the application to launch streaming video".» Initially, the problem was temporary, that is occasionally the webcam began video streaming without any problem, but as the time passed, webcam stopped working almost completely.

    TRIED SOLUTIONS:

    I tried all the solutions mentioned below:

    • I uninstalled the Dell webcam software and reinstalled with the version installed in the factory, supplied on CD with laptop. Uninstalled the webcam via the Device Manager and reinstalled, but without success.
    • I heard that there is a conflict between the Dell face recognition software and dell webcam central. So, I uninstalled the dell face recognition software. After that, the webcam worked for a few days, and there still rebooted problem.
    • I went through various forums online, dell community, customer service, etc. and everything suggested tried but without success. I heard several times that this is not a hardware fault but driver error. Even in a few forums, its says that Creative Technology Limited have not been able to supply webcam drivers compatible with windows 7 64-bit.
    • I even did factory restore my laptop twice, but could not do my webcam works.
    • Then, I decided to format my system and installed windows7 again with the disc that came with my laptop. During this process, I have kept the recovery drive and the untouched OEM disk untouched. I have reinstalled all the drivers in such order as advised by Dell. Despite puts everything in order, I couldn't do my built-in webcam work. More... now I can't even access the Dell factory restore option despite the fact that my recovery disk is intact and it is to have all the files into it!
    • I tried the utility dell online Diagnostics. He could not detect any error webcam!
    • Few days back, I used the dell startup screen diagnostic utility and scanned the built-in webcam to find errors, and my webcam failed in all tests! Here are the screenshots of the tests:

    I GUESS I GAVE ENOUGH INFORMATION THAT CAN HELP TO DIAGNOSE THE PROBLEM WITH MY DELL INTEGRATED WEBCAM... I ASKED DELL CUSTOMER SERVICE TO HELP ME SOLVE MY PROBLEM OF WEBCAM... AND ALSO THE FACTORY RESTORE INACCESSIBILITY PROBLEM... PLEASE HELP ME...

    AFTER AN ENTIRE WEEK OF UNINSTALLING - REINSTALLING VARIOUS DRIVERS & SOFTWARE FOUND IN THESE FORUMS, SUGGESTIONS INCLUDING REINSTALLING WINDOWS FROM DELL DATA SECURE BACKUP.  THIS IS WHAT I LEARNED.

    My problem was. No supported webcam not connected when I ran dell webcam central. No program could access the webcam. Device Manager showed SPECIFIC DEVICE. Camera suddenly stopped working! I had a little more hair when this problem started.

    I have Inspiron N4010 windows 7 Home premium. Are the drivers for the webcam in windows 7, there is no separate drivers available anywhere. with the exception of some XPS models.

    A post in these forums suggests to abolish the plastic around the display bezel. It's simple. Just carefully go around and remove. It is clipped without screws on my system. This gives access to the webcam hardware. I got dell webcam central on-board. (showing no supported webcam connected!). Gently, I tried to disconnect the connector of the webcam. My intention was to disconnect and reconnect. I barely touched and the fire came and windows immediately started to install device drivers. A beep and an icon in the notification bar popped up. A few minutes, I saw my beautiful mug on the screen to my absolute delight.

    Guys, if you have a problem where Device Manager does not recognize your webcam for most probably, this is a hardware problem. The small rectangular plate on which is mounted the webcam is not properly secured by DEll. It is a DESIGN PROBLEM. The Board is located in place on two small round plastic holders without any screws. It can move easily. The bezel plastic when it is installed itself that holds it in place, but not very effective. When you open and close the lid of the screen, especially if you are taking in the middle where the camera you finally loose connector. That's why some messages will tell you what they camera has stopped working suddenly and then started working by himself all of a sudden. When I put the bezel plastic, it snaps into place, I was able to move the camera, and it stopped working again. A little gentle jiggle got running again and its been since.

    It does not matter what version of central webcam you have in windows 7. It runs on windows Vista service pack 2 compatibility mode. (Find WEBCAMDELL2. EXE file under programs x 86-dellwebcam-dellwebcam Central-dell webcam central. Right-click on the file name. Select Properties. Select the Compatibility tab and run this program in compatibility select windows vista service pack 2).

    If in your case even though there might be a software problem. always try this simple 2 minute solution b4 safe spending frustrating days find the drivers and software. Hope this post helps someone. May work on other systems too! Good luck! and thank you to the guy who led me down this path and misery!

  • fusion of forms in question please help


    issue.jpgI have a problem: when I tried to merge forms into one with pathfinder, I lost part of the mountain... Please help me. How can I merge without losing?

    Make transparent traces on the forms of mountain before using 'unit '.

  • Layer Mask question, please help.

    Hello

    My layer mask does not work, do not know what is happening. I use 4 CS. I want to use the blend effect so I put the photos on a white background. I click on the layer mask on each photo, select the tool brush on the picture but does not work, is either appear black or white when I use the brush paint on it. So not bad, the foreground color should be gray & white based on layer mask, but it appears black & white instead. Please see the screenshot below. Please help, thanks

    Untitled-2.jpg

    Hi, I'm going to try explain your problem.

    In your posted example we see that you have three layers in the layers panel.

    On each layer, we can see, on the left side, there is the thumbnail of the layer, it is a display of the actual image of your layer, then a thumbnail of the layer mask (the white rectangle on the right side).

    A layer mask works as follows: you tell Photoshop to show or hide the actual parts (pixels) of the layer with the grayscale values. Indicates a white pixel on the layer masks Photoshop to display the area of the image with a (non-transparent) full opacity, while tells a black pixel on the Photoshop layer mask to hide the layer completely (0% opacity.) Gray values will therefore partially show the image data.

    But you paint on the document, and you must specify Photoshop if you want to paint on the image (what you did in your example, and you don't want to) or if you want to paint on the layer mask (what you want to do). This indication is called targeting. It is simply done by clicking on the thumbnail of the layer or the layer of your layer mask thumbnail. (By clicking on different areas of a layer in the palette layers are different orders, you give to the program). For example, if you want to move the layer that you hide to another, in order to paint on his mask, sure to click on the layer of the other layer mask thumbnail in the layers panel.

    In Photoshop CS5.5 and earlier versions, you'll see that a layer or its mask is targeted because there will be three contours around her: a black, a white and a black once again, as the actual layer data in the highlight 0928 your image layer. You should see these three contours around the layer mask to paint over it.

    CS6 the target indicator is different, look in my image, we can see that the layer mask is targeted with white corners: I then have the part of the black layer mask by targeting the layer mask in the layer panel and then paint on the image where I want to hide the layer.

    If you want to change the layer (photos, in your case), just click on the thumbnail, and you're ready to go!

    I hope this helps.

    See these help documents: laquerbe Basics: http://help.adobe.com/en_US/photoshop/cs/using/WSfd1234e1c4b69f30ea53e41001031ab64-78e3a.h tml

    Layer masks: http://helpx.adobe.com/photoshop/using/masking-layers.html

    Some the search results for "Masks fundamental layer" in Photoshop help: http://community.adobe.com/help/search.html?q=layer+mask+basics&x=0&y=0&lbl=photoshop_prod uct_adobelr & hl = en_US & lr = en_US & auto = 0 & area = 0

    (It is one of the best ways to search for files of tutorials or help)

    Stone

  • Z51 - initial set-up configuration question - please help

    This seems to be c reallysillyquetion b I'm nowhere fast.

    I tried to start using my new Lenovo Z51 but I can't go beyond where it says "help us to protect your information.

    I selected a different email for a security code to send to account.

    Then he said: "to verify that this is your email address enter below and click 'next' to receive your code.

    So I got my windows account email address - you click on "next" and get to the next screen

    The next screen has message saying "enter the code you received - if * is the address of e-mail on your account, we will send you a code."

    But I do not get anything - so when it asks me to enter my e-mail address means enter the same address that I chose to have the sent code, rather than my windows email account?

    Please can someone help save my sanity?

    Helen

    Mod edit: System model added to the subject line to improve visibility / clarity

    Ignore my question - after trying both options again, I actually sent the code, able to move to the next step. Hoping that there are no more problems.

  • Simple Data Acquisition question please Help!

    I have problems with a simple LabVIEW program.

    I'm analyzing two inputs voltage and at the moment I have the VI work so that both are analyzed at 10 k Hz simultaneously and displayed in two tables of waveform.  What I would do, it is write values for them at 1 Hz in an excel spreadsheet or a text file with the time, the value of the first and the second value.  So I would create an array of [value1, value2] and export that to a line in a text file, I can analyze and then later in excellent.  I want to keep it that way for the duration of the program. In addition, it is possible to have the LabVIEW to generate such a table statistics once the user closes the loop, it would be even better.

    I can only assume that it is not too complicated, but I've never done any export data and just a quick explanation probably will save me a lot of time.  Any help would be great, even if it's just to say "use this feature.  Thank you very much.

    Pieter

    Pieter,

    Please post on the Forums of NOR. I could take an example that was similar to yours and organize data in the format you want. I've included a photo as well as saved for LabVIEW 8.6 VI. I took the data from the berries that were from the channel to read and handle while he was in the format of time, channel 0 channel 1. Hope this helps and let me know if you have any questions. Thank you!

  • ESX 3.5 license NOW QUESTION Please HELP!

    After the bottom of 4 ESX 3.5 are connected to the ESX VC server on the host. After reboot ESX * do not start going that no licens is on this host running VC server. So I can not start server VC. I think that all licenses filen is based on

    the VC server.

    Help, please!

    Unfortunately, ESX 3.5 uses a license server that is installed on the server vCenter Server. In order to avoid the question, you are probably experiencing there is a period of 14 days, which however does not always work as expected. What you need to do in this case, is to generate a "hosted" the portal of My VMware license (I hope, it's still possible) to the ESX host on which vCenter Server is currently registered. After assigning the license to the host you should be able to turn to vCenter again.

    André

  • Drag - move the question, please help.

    I can no longer drag and drop photos into photoshop elements 12.  When you work with a layer, I want to move a layer in a different existing file and no longer have the faculty.  The only way I solved the problem in the past is to uninstall and reinstall the program.  I have read the other posts of the forum and followed the instructions by resetting the preferences and it does not work.

    Someone at - it solutions to this problem?  Help, please!

    With the two files open, simpler to tiles side by side, you should be able to drag the layer from the source file in the target file. Measure where it shows the "gripping hand" you can release the mouse and you have to add the layer to the target.

    So what happens on your system now? When you drag the layer to the target which icon is displayed - "gripping hand", "no entry", something else?

    See you soon,.
    --
    Neale
    Insanity is hereditary, get you your children

    If this post or by post from another user solves the original problem, please mark as correct and/or useful messages accordingly. This helps other users with similar trouble getting answers to their questions more quickly. Thank you.

  • Acer Aspire One Internet questions (Please HELP)

    Hey guys!

    I recently bought an Acer Aspire One netbook for school. The computer is just amazing in every way, shape and form - outside the horribly slow and buggy internet. Regardless of my connection or the browser, I have problems such as limited connections insane, usually internet slow speed and all disconnections that occur without reason. If I disconnect and reconnect to the network even after a question given, however, it works very well for the next thirty-or-so minutes, and I encounter the problem again. I noticed that if I closed the computer at a given time, open it and use the internet, these issues seem to be more important. Restarting the computer seems to temporarily solve the problem for a decent time period, but I have to restart the computer several times during a period of use, which is very inconvenient and frustrating. Due to the fact that my school is entirely internet-based, these issues (that occur whenever I use the computer, by the way) become ridiculously boring. Anyone who suffers these problems? Is it possible to fix this?

    (Disclaimer: I studied the problem and saw that there was a 'feature' that slows down the speed of the internet to save the battery, which can be disabled in the settings.) However, after doing this, these issues continue to persist.)

    ~ JF

    Thanks for the help, everyone.

  • typeof == 'movieclip'... .the weird question (please help)

    My clips (mc1, mc2, mc3, mc4, mc5 to click) are present (mainMap.map.pan) of depth. so when I set my movieclips I! = "click on" that is to say, should not be "click on" movieclip inside the mainMap.map.pan, but when I'm followed on turnover, it output "click on" movieclip, please someone help me pick up all other movieclips other than 'click' in my mainMap.map.pan

    (all I'm trying to do is, when a turning on any of the mc1, mc2, etc. in my toolTipMC should display information according to XML elements).

    MC = mainMap.map.pan;

    for {(i-mc)

    If (typeof (mc [i]) == 'movieclip' & & I! = "click") {}

    myBtn = mc [i];
    myBtn._alpha = 100;
    this.useHandCursor = false;

    myBtn.txt = titles [i];
    details [i] = myBtn.txt2;
    myBtn.img = images [i];

    myBtn.onRollOver = function() {}

    If {(miniMap._visible)
    this.useHandCursor = false;

    toolTipMC._x = point.x;
    toolTipMC._y = point.y;

    toolTipMC._visible = true;

    trace (i); for some reason, it always gives me 'click '.

    toolTipMC.img.imgHolder.loadMovie (this.img);
    toolTipMC.tip.text = [this.txt2] titles;
    toolTipMC.detail.text = details [this.txt];
    } else {}
    this.useHandCursor = false;
    }
    myBtn._alpha = 100;
    myBtn.setRGB (0 x 003366);

    };

    your record shows you the last value of i in your loop.  It has nothing to do with the movieclip in reversal.

    It would be more informative you can use:

    MC = mainMap.map.pan;

    for {(i-mc)
       
    If (typeof (mc [i]) == "movieclip" & I! = "click") {}
           
    myBtn = mc [i];
    myBtn._alpha = 100;
    this.useHandCursor = false;
           
    myBtn.txt = titles [i];
    details [i] = myBtn.txt2;
    myBtn.img = images [i];
           
           
    myBtn.onRollOver = function() {}
               
               
    If {(miniMap._visible)
    this.useHandCursor = false;
           
    toolTipMC._x = point.x;
    toolTipMC._y = point.y;

    toolTipMC._visible = true;

    trace (this._name);

    or even more useful:

    trace (this);

    toolTipMC.img.imgHolder.loadMovie (this.img);
    toolTipMC.tip.text = [this.txt2] titles;


    toolTipMC.detail.text = details [this.txt];
    } else {}
    this.useHandCursor = false;
    }
    myBtn._alpha = 100;
    myBtn.setRGB (0 x 003366);
               
    };

Maybe you are looking for

  • 4th gen Apple TV... can he take over 480 resolution or 1080i?

    Yes, I have an old CRT 60 inch TV that has just 480 p and 1080i and I love it!  Apple TV 3rd generation, I did currently 480... so can the most recent Apple at least 480 too?

  • HP 8600 goes to sleep, disappears from the network

    I have a new HP 8600, Windows 7, AT & T router.  Everything works fine except the printer goes to sleep and the router can't find it.  The façade is dark and when he woke up shows that it is connected to an intense sound signal.  It is not!  I have t

  • 646 and 80070652 error codes

    My computer has tried and failed to install 6 upgrades for several days. I get the code 646 and previously obtained code 80070652.  any suggestions?

  • Cancel the problems caused by Windows 7 updates

    It's new, the standard operating system of Microsoft for Windows 7 to 45 minutes to work out its kinks and be functional?  From the Auto Update April 30, that's my experience.  My new laptop Toshiba with preinstalled Windows 7 worked beautifully.  Be

  • How to get an update for Gigabyte 77TA-UD 3/F2

    Original title: Bios updates Can someone advise me how to get an update if there is one for: Gigabyte 77TA-UD 3 / F2