WRT160N: Getting dynamic IP address 169

Similar Questions

• Linksys WRT160n v3 and dynamic IP address

  Welcome,
  I use TImeWarner cable to internet.
  These days tw uses dynamic IP addresses.
  So my "WRT160n v3" breaks down, when this change takes place.
  Is it possible to configure the "WRT160n v3" to handle this?

  I have networkMagicBasic.

  If not, can a Belkin 'N750 DB' manage dynamic addressing?

  Thanks for your help... Vernon

  It has already provided a working solution. Click here.

• Satellite Pro L300 - 12 H did not get the IP address of the DHCP router via cable

  My Vista Premium SP1 laptop is connected via a wireless connection to a modem/router ADSL Buffalo WBMR-G54 model that works very well. However, I tried the other day to connect the NIC via a RJ45 cable to the router and it won't work! I get the message "limited connectivity" and an IP of 169.254.xxx.xxx that suggests he does not get an IP address from the router.

  I was on various websites and tried all sorts of things as uncheck ipv6 on the properties of LAN card, put off the power of the DHCP Broadcast flag in the registry (according to the number of micrsoft) etc but nothing works.

  Anyone have any suggestions to make it work?
  NB: I took the laptop in work and plugged into the Windows 2003 Server network and got a DHCP IP immediately!

  You asked for help by your Internet provider?

• Registry files have been deleted via a Norton 360 3.0 registry clean up - can't get an ip address from the router

  I'm running Vista Ultimate, -connection (Ethernet) with Verizon FIOS I ran a Norton registry clean and foolishly trust what he says to remove.

  At first, all of my USB cards have been screwed up (noted in the Device Manager with exclamation next to each one points)
  I did a system restore and that corrects this problem, but now I'm having a problem with my network card.
  , All diagnostic tests, etc. show that the material is very good. My router is also fine the problem is that windows can't get an IP address from the router and then assigns his own
  (a # 169 instead of a # 192)
  In the network connection properties, it says that the device is functioning correctly, and the driver is up-to-date.
  'Connection speed' tab: a window of diagnosstics is: I ran testto test adapters connect to connect to the network.
  Results: connection Test
  Test details:

  I have "this card is configured to obtain an IP address automatically. No DHCP server is present on the network. Windows selected an IP address by using the alternative private IP addressing. »

  X "Ping 0.0.0.0 Gateway: failure.
  !  "No DNS server is available for this connection.
  ! "No WINS server is available for this computer.
  X "Ping 0.0.0.0 network: failure.
  ------------------- -------------------------------------------------------------------------------------------------------------
  In this same window of diagnostics under the "LinksTab".
  Link current test status: (what is determine the current connection speed of the adapter and link partner)
  Results:
  ! The adapter is configured to negotiate the speed with the link partner, but 1000 Mbps was chosen as one of the possible speeds.

  The best link options-results of the speed test:
  ! Could not detect way reliable speed and duplex settings. Possible speed/duplex settings are 100 Mbps Full Duplex and Half Duplex 100.
  (Note that these link tests are online and I can't online)

  Also in the Diagnostics window-under the 'Cable' link cable - past-polarity is normal.
  Depending on the tab is the Hardware tab
  Hardware diagnostics check for I/O conflicts...
  Results: all the tests:
  EEPROM test
  FIFO test
  Test register
  Interruption of the tests
  Loopback test

  I also went in the prompt type in IPCONFIG... c which shows:
  Ethernet connection to the Local network card:
  ConnectionSpecific DNS suffix: (it's completely empty here)
  Link-local IPv6 address: fe80::bda9:951 d: 619f:a0dc 9%
  Autoconfiguration IPv4 address: 169.254.160.220
  Subnet mask: 255.255.0.0
  Default Gateway: 0.0.0.0

  I also have a sort of ping command here-cant remember the command, but the results were in the CBS... I didn't know how to reach. He however escape from something on the registry files.

  I went throughD-Link Tech router (router) support is good, Fios Tech support everything set up right, - Norton support(Norton denies that the files were not to be touched-although their report shows these registry files were deleted)-Dell Tech support because my warranty missed 3 weeks ago - although I still have the "your Tech Support team until 2013 - which is valid only if you have a hardware warranty-made no sense sold me the car without. the engine - directed the FTC to bring a complaint about it - after I get this fixed number.

  I hope someone can help... by the way I get perfectly in line with my laptop - I know this isn't my router. I'm sure it's due to some registry files being moved-(j'ai eu deles de messages d'erreur indiquant que les fichiers de Registre ont été endommagées ou manquantes) what do I do now? No system restore to restore this part of the register - I also installed the drivers from the dell drivers and Utilities disc - but maybe I've done that correctly? I put the disc - extract files-(he says they have been unpacked) was a new step for me to do after that? Help, please!
  Thank you!

  Hello
   
  We recommend that you install the router (see its manual) and the pilot of NIC once more and check the difference. In the first post, you mentioned that you decompressed or extracted files. Once the files are extracted, you will be asked to install the driver. However if you do not receive any prompts for the driver, then you will need to locate the destination folder where the files are checked to find the configuration file.
  
  Open the destination folder where the files are extracted and run the Setup file to complete the installation.
   
  To download and install the latest network card driver, visit the site Web of the manufacturer of the device or system.
   
  For more information on downloading and installing the drivers, visit this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/the-hunt-for-drivers-how-to-find-Windows-Vista-drivers-for-all-your-hardware
   
  I hope this helps.
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• How to change (dynamic) IP address in Windows 7 or Vista?

  Had the same problem on Vista, upgrade to Win7 and the question remains.

  I have a dynamic IP address from ISP, but it remains as if it was static, what allows to work in XP and previous versions of Windows no longer works in Vista or 7. I talked to my ISP (3 times, 3 different Tech), they said that my IP is dynamic and confirmed he is not defined by them as static. They charge more for a static IP, it would just give me this free 'upgrade'. They had "no idea" how to force/change a new IP address in Vista or 7.

  Please! Don't bother suggesting to run ipconfig/flushdns / release / renew at the prompt to as suggested by each internet search, this DOES NOT WORK. This was done with the prompt window of cmd under "Run As Administrator".

  Please! Read everything I've done here before suggesting something, I have tried or have tested and proven to work/not work.

  Here are other things that I've tried, WHO ALSO DO NOT WORK:

  (NOTE: no router is used, directly connected, CAT5, NIC the modem PC broadband)
  -Modem unplugged 72 hours left. No change
  -A the ISP send me a new modem. No change
  -Uninstalled NIC. No change
  -Change IP4 settings to "Obtain automatically" to a forced IP made-up, rebooted, then changed back to auto. No change

  So, with all this 'old school' stuff already tried and failed, that changed in Vista and 7 which seems to keep the same dynamic IP static? When Windows is put in cache or store this information, so I can delete it, none of the traditional methods of work. I absolutely can't stand having a static IP address on my computer at home.

  If you search on the internet this exact question you will find what I have, everyone is suggesting to the methods of work time I tried already above, but people using Vista or 7 are several times to find it no longer works.

  Here is some information, which confirms the IP address is not stored in my modem, or assigned to the MAC address of my NIC...

  If I start this same PC with a LINUX Live CD, type using the same MAC address and the NIC, he gets another IP address whenever it restarts. The question clearly has nothing to do with my ISP, modem or PC in general.

  If I get hot swap my modem to another PC, the other PC Gets a fresh (different) IP address. If this another PC using XP I can force the ipconfig/release / renew to change its IP address.

  If the other PC running Vista, the IP address remains static, no matter what I try, unless the hard drive is wiped and Vista is re-installed, then he gets a new IP on the PC with the pure install, but it can not be changed after what is happening.

  If clear, Windows Vista and Windows 7 have somewhere IP configuration information and re-use of this information when it detects that you are using the same internet provider, WHERE is it stored so I can delete it?

  I thank you much if you have a working solution and actually know the answer, instead of reading everything that can already be found by a search engine and repost info which is no longer valid, as all the world on the internet is doing in trying to answer this question.

  I think I found a solution. It has worked for me so I guess it could work for you.

  1. find your IP address for example to go to a site such as http://www.whatismyip.com/ it will show you your IP address.
  2 copy.
  3. open network & sharing Center
  4. open the network properties you what your IP to change. In my case, it's an EVDO modem.
  5. on the network tab, double-click TCP/IPv4, which will open a window to change the IP and DNS IP address.
  6. in this window click on "use following IP address" and paste this IP address you copied in step 2.
  7 change the last digit of the IP address to any value above him for example if its 192.168.23.123 change the last digit to something like 122 so that the IP address becomes 192.168.23.122.
  8. click on OK until that close all windows.
  9 disconnect from this network.
  10 reconnect to this network and if it goes as planned the ISP should force a dynamic IP address. Check http://www.whatismyip.com/ if it has changed. If you can not browse, go to step 6, and then select "Obtain an IP address automatically" and then disconnect-> reconnect to the network.
  It worked for me so I don't know if it will work for you. Your comments will be greatly appreciated.

• Windows 7 - cannot get the IP address of the DHCP Linux server

  I have several desktop computers and portable computers that have the Windows 7 operating system.  Some have Windows 7 Starter, Windows 7 Home and Windows 7 Professional.

  My network is configured like this:

  Desktop computers > switch > DHCP Linux server > router > Internet

  Laptops > wireless bridge > DHCP Linux server > router > Internet

  Windows 7 Professional does not appear to have a problem with my set up.  It can enter an address IPv4 automatically, wired or wireless.

  Windows 7 Starter and Home cannot obtain address IPv4 correctly, wired or wireless.  If I give the static addresses of these computers, they can access the internet.  If I let them as dynamic, they will constantly try to connect and try to Identifingtwork.

  I want to get my Windows 7 start and home computers to enter dynamic IPv4 addresses of my Linux DHCP server.  Note, I have never had any problem with Windows XP Home or Pro.

  Hello
  
  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.
  Please post your question in the TechNet Windows 7 networking forum.
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• "Error: failed to get the IP address of the destination virtual machine running the converter to assistance server." with a static IP address

  Hi all

  I'm trying to p2v linux 6.4. It fails with the following message is displayed:

  Error: Cannot get the IP address of the virtual destination machine running the converter assistance server.

  I have seen discussions on this message, but they all refer to dynamic IP address, taken from DHCP, as in my case, I use static IP address.

  In the meantime the p2v (which then breaks down...) I open console support machine and saw a message:

  
  

  eth0 is not a recognized interface.

  Can someone tell me what is happening?

  Hello

  I assume you are using converter 5.5. There is a new feature that allows the selection of the network card. However, it works well in the case of Linux P2V. If you have changed the type of adapter, use 'e1000' or 'auto' and try again.

  HTH

  Plamen

• I have two email addresses, how do I get my second address

  I have two email addresses, how do I get my second address

  Just add the two addresses of Thunderbird. The first time you run it, it will ask you to create an account.

  Later, you can go via file | New | Existing account Mail and add another.

  Or tools | Accounts settings | Accountable for the Actions and add a Mail account.

  Or Application Menu. New Message | Add an existing account.

  "application Menu" means that the button with the three lines! Looks like a hamburger.

• (Get Mail, write, address book etc) buttons disappeared

  All the top buttons disappeared (like getting mail, write, address book etc). How can I get back them?

  In the main menu bar:
  
  Display - toolbars
  
  Check "Mail Toolbar.

  In the case where the menu bar is hidden so press Alt or F10 to bring it back.

• I forgot my security question answer on my account and I get lost email address of relief

  I forgot my security question answer on my account and I get lost rescue address, how do I get my new security question?

  Contact Apple for assistance with the security of the Apple ID - Apple Support accounts

• How to get the IP address of the client when TCP connect on the server

  How to get the IP address of the client when TCP connect on the server.

  The only parameter obtained the login is the login ID.

  I assume you are using "Wait of TCP on the listening port" on the server. This returns the remote address and port (like out in option).

• How can I get an IP address from an Xbox 360 that was stolen from me?

  My Xbox 360 was stolen recently, and I've never written the IP address for it. Is it possible to get the IP address just to have an online account? also, is it possible to trace the IP address the next time she signs online to get a physical address for info from police?

  You can go to www.xbox.com and login to your account then go to payment options manage then that should show your credit card information, then click on delete and who must take care of your card being removed. If for any reason, you are having disconnected you can call support and they can remove it for you. You can also check your local wages as well, and if you had saved your console, support will be your serial number on the registration and then you can get your Xbox if you find at a pawn shop. Hope that helps some.

• My email account has been hacked and changed the password. I'm trying to get a contact address for hotmail get this account deleted

  E-mail address of hotmail

  My email account has been hacked and changed the password. I'm trying to get a contact address for hotmail get this account deleted

  Unfortunately, this forum is not for Hotmail. They have a dedicated forum for any questions.

  If your account has been hacked:

  Compromised account - unauthorized account access:

  http://windowslivehelp.com/solution.aspx?SolutionID=6ea0c7b3-1473-4176-b03f-145b951dcb41

  Hotmail support:

  http://windowslivehelp.com/product.aspx?ProductID=1

• Updates of Windows cannot open in the start menu, but I can't go to her Parderogationauparagraphe (help & support), but I get error (incorrect address)

  IMPOSSIBLE TO OPEN WINDOWS UPDATES IN THE MENU START, I CAN HELP N & SUPPORT. I GET AN INCORRECT ADDRESS

  Hi 1319bigdon,

  ·         You did changes to the computer before the show?

  Follow the steps in the article.

  You may be unable to access the site Web Windows Update in Windows XP, Windows 2000, or Windows Server 2003 if these versions of Windows are not updated with the latest Service Pack

  http://support.Microsoft.com/kb/2497281

  Cannot install Windows updates

  http://support.Microsoft.com/kb/555461

• Batch file to get the IP address of a spesific adapter

  I found the following code to get the IP address.

  : GetIP
  : IP for the main map
  setlocal
  for /f "delims =: tokens = 1-2 ' %% in (' ipconfig / all ^ | find" IP address "'" ") set GetIP = % d
  ENDLOCAL & GetIP value = % GetIP: ~ 1%
  Goto: EOF

  but as noted only give to the main Board. I want to be able to specify which adapter

  but I struggle to decode this script.

  Hello

  The question you have posted will be well suited in the MSDN Community. Click on the link below.

  http://social.msdn.Microsoft.com/forums/en/categories/

   

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.