WRT160N urgent help
I have a speedtouch ST516 and a WRT160N router (on the back of the modem, he said WRT160N, I guess that's the v1). While I have this scenario a year ago I once again because I have reset the configurations.
I have the following scenarios:
1.I can connect to the ip address of the modem without the router linksys
2.i can connect to the ip of the router with the router and the modem connected.
3.I remember having DHCP disabled last year, because the ST516 speedtouch can also assign IP addresses and ports.
4.I use PPPoE on my modem.
Basically I want the router must be disabled for the assignment of ip addresses (I think this removes the problem of Dual router network. However, I want the router to send signals wireless for my laptop and other devices (I can configure it myself once everything works).
Other info:
My linksys router uses 192.168.1.1 subnet
My speedtouch 516 use 192.168.1.254
I believe that they should be presented in the same subnet to do port forwarding?...
I think I'm looking for something in the knowledge base with the name of "Setting up a Linksys router with DSL Internet" with a speedtouch516 or a double router
You said that the speed you're paying for "up to 6 Mbps (megabits per second)", but you get 250 Kbps to 300 Kbps (300 kilobytes per second = approximately 3000 kilobits per second = about 3 Mbit/s). 300 kb/s = approximately 3000 Kbps, because although there are 8 bits in a byte, the 300 kb/s is a download speed of data, and the 3000 Kbps is the speed of the line needed to download that amount of data. This 10-bit transmission, per byte of data received, occurs because of the protocol above, occasional transmissions, etc. So it seems that your network is working properly, but your ISP provides only half the speed that you pay.
This lower speed may be because (1) you live a distance away from the nearest train station from your phone company (this problem is can be corrected by moving) or (2) your telephone company (ISP) set their switches 3 Mbps instead of 6 Mbps of service (it's can be corrected by a phone call to your telephone company more strong emphasis on your part!) or (3) for a reason any your computer a gets bogged down (to solve this problem clean your computer to optimize its speed).
To find out if your computer is performed by (3) above, test your modem with a known fast computer.
Please also indicate the serial number and model of the computer you are using.
*************************************
Oops. I see that I make a mistake in my last post. When I said:
"If your P2P software (utorrent) requires that you transfer a port on your computer, then you need to give your computer a static LAN IP address." Note that any fixed LAN IP address must be outside your range of DHCP server, and it may not end in 0, 1, or 254. »
This information applies to Linksys routers. Because your network is controlled by your ST516 router, I don't know if this info even applies to you. So you should not give your computer a static LAN IP address, and you should not put this address outside your range of DHCP server. Note that some routers are exactly the opposite of Linksys, which is with some routers, you must put the fixed LAN IP addresses within the range of the DHCP server.
Tags: Linksys Routers
Similar Questions
-
Unable to open gmail and other google account services. Need urgent help. Firefox version is 29.0.1. Deleted all cache and history + wiped without addons. Urgent help please. Same problem in other browsers ie opera/IE. Other Internet sites without problem.
Personally, I've never had problems with ABP, but questions about ABP would be better answered in the AdBlock Plus forum where there are people more suited to respond as we only deal with technical support from Mozilla (e.. g the Fx of Firefox, Thunderbird, for Android)
-
How can I reset my password bios compaq mini CNU0092ZTQ please urgent help
How can I reset my bios password for compaq mini cq10
Need urgent help CNU0092ZTQ
Hello
Enter: e9l11o70a5 (3rd character is a lowercase L and the 8th sucks)
Kind regards
DP - K
-
URGENT HELP NEEDED: How to reset the Editor window title?
Hello
I managed to screw up my title window. First he attached somehow itself as a 'inserted window' (such as preview windows and the edition of the effect) and I lost all the tools. I managed to detach other windows, but I still can't tools in his place. So I can't change my titles. I'm very far behind on a project that I'm trying, and I can't take more problems like this at the moment. Please help me solve this problem!
Here you can see the problem illustrated with some screenshots: https://linustechtips.com/main/topic/645257-urgent-help-how-to-get-my-title-editor-back-in - first-pro-cc /
Help, please!
Reset your workspace in the window menu.
-
Please, I need urgent help. I can not install applications, the site says I have not produced, but I pay every month!
Hi Jose % 20Dieciseis,
I checked your account via email that you used to register on the support Forum, it shows not all subscription registered on your Adobe account.
could be a possibility that you used an e-mail to subscribe to the composition.
If there is no trouble finding that-
Please contact Adobe customer care http://helpx.adobe.com/contact.html
- Remember that you are logged on the page with your Adobe ID.
- Select your product and what you need help with
- Click on the blue box "still need help? Contact us. "
-
Hi, I paid the subscription to muse, received confirmation 7 hours ago, but the subscription is only showing on the site not on the creaitve cloud. I need urgent help for a period
Hi Se80799442,
Adobe trial and purchased applications are same, if you are showing that the trial has expired it would be a mistake to solve this, you can check the link below:
( Make sure you use the same Adobe ID / Email ID that you used to purchase the subscription )
Download the creative application of cloud from here: Download Adobe Creative Cloud apps | Adobe Creative Cloud free trial
Connect and disconnect activate Cloud Creative applications
If it does not help him follow the link below
Adobe Creative Cloud apps back in test mode after 2015 set CC to update
* NOTE: Make sure that your firewall of your computer or security software firewall does not block Adobe, if you are not sure of it then just turn off the firewall for awhile disconnect you and you connect on the creative application of cloud and check.
Let us know if that helps.
-
Need urgent help with the startup of the database
Hi all
I use oracle 10g on 32 bits of windower server.
I try to start my database today and it gives me error, and that's my production database.
I need very urgent help you. (I have no rman backup, and data are not n6cessoires so, since it is the practice of the student).
Kind regards.SQL> startup open ORACLE instance started. Total System Global Area 524288000 bytes Fixed Size 790180 bytes Variable Size 250343772 bytes Database Buffers 272629760 bytes Redo Buffers 524288 bytes Database mounted. ORA-01110: data file 34: 'G:\ORACLE\DATAFILES_ACADEMY\ACADEMY' ORA-01115: IO error reading block from file 34 (block # 1) ORA-27070: async read/write failed OSD-04016: Error queuing an asynchronous I/O request. O/S-Error: (OS 23) Data error (cyclic redundancy check).Maahjoor wrote:
Hi dear,I need further assistance on your side, I restarted the server, but the same problem.
as there is a way to drop and re-create a system tablespace? given that the 34 file belong to the tablesapce system.concerning
N °
So just create a new database. Who will have every ten minutes. And to say that your students to create new storage spaces. Who will be the two minutes. -
Loading XML into the intranet? urgent help please...
Dear friends, I need urgent help: I have a screen CAYIN (which allows me to display the evetns, etc.) and gives me the possibility of loading / displaying a FLASH (SWF) file, well, I need this SWF to load data XML ("texto.xml") but seems when the CAYIN programme that is running flash, does not the SWF find the XML code in the same folder...
Then I tried many ways to load the XML file without success up to now. Some tests are:
obj_xml. Load("\\192.168.0.100\media\texto.xml")
obj_xml. Load("\media\texto.xml")
obj_xml. Load ("texto.xml")
obj_xml. Load("..) ("/ media/texto.xml")
obj_xml. Load("\\media\texto.xml")
obj_xml. Load("file:\\192.168.0.100\media\texto.xml")
obj_xml. Load("..) \\192.168.0.100\media\texto. XML")
I guess I write something wrong or forget something. Could someone help me please? because these files are in a '192.168.0.100' internal server (intranet).
Emergency help please, thanks in advance,
If the swf file is in a directory with subdirectory media that contains texto.xml, use:
obj_xml. Load("Media/texto.xml")
-
Dashboard guest - need urgent help
When I want to create guest of dashboard with two guests on the same column, it will not work. I use the variables of presentation for filtering.
Example:
in a command prompt
I use equal to a x 1 presentation variable hire_date, and
also equal to a variable presentation x 2 hire_date,
and then I send you this variables in some report when I filter on column and say x 1 < = hire_date < = x 2.
But this line does not work... may not work if you use a single column and want to equal this column with the two variables of presentation...
I really need urgent help... I right here...When you create the first instance of rapid change (code) fx go hiredate as below
cases where 1 = 1 then hiredate otherwise hiredate end
then assign it to the variable.
Now you can add hiredate again and assign it to another variable.
-
Need urgent help! (combine invites and formula)
Hello
I use Oracle Business Intelligence 10.1.3.3.2 and create reports of responses. I desperately need to combine
Invites and formula on a column.
I need to use guest in my formula on a column.
Need urgent help!You can use the presentation variables to pass the value of the command prompt in the report or any formula in the column.
In the dash prompt, you see an option called 'Set the Variable' where, and you must give a name to the variable. (Say Var_value)
Now, the value of the variable can be referenced simply by using the syntax @{name} {10}. Here '10' being the default is optional you can simply reference using the @{Name} and you value invited past.
Hope this works
Thank you
Prash -
Hi guys,.
I just ordered two WRT160N and I have some doubts. I will use one of the routers connected by cable to my modem and my PC.
I wanted to use it as a "wireless adapter" for my tank Multimedia Networking (PopCorn Hour A - 110). My question is: can the WRT-160N to work in client mode?
If you know, please answer as soon as possible so I can later cancel the order.
Thank you.
Gotenks
Hello gotenks, Nope it won't work because the WRT160N device you have does not have capacity to receive the wireless signal, it can send wireless signals. If you want to get your fill of wireless network media, then get a WGA600N! This wireless device will be the adapter wireless for your media tank network and you can receive the signal from your wireless router wireless. I hope this helps...
-
Use 2 excerpts, he worked throughout the process pump & replicate data but just one hour back, he wasn't the replication...
I could see the State of extracts, data pumps and replicates as running. In the machine 1, I 2 extracts & datapumps of 2 data running in the machine 2, I 2 replicates are running.
When I do the ext lhrdev1 stats he showed the no. of records inserted, updated, deleted while that for the same snippet of lhrdev1 nothing displayed when I do rhrdev1 (replicat) stats in the target machine.
Can someone help me solve this upward.
================================================================================
Source system
================================================================================
EXTRACT LHRDEV1
ID USER, PASSWORD GGS GGS
EXTTRAIL E:\Oracle_GoldenGate\V22232-01\dirdat\L1
DDL ARE MAPPED
-DDLOPTIONS REPORT
DDLOPTIONS ADDTRANDATA
-This report
-REPORT AT 08:00
-REPORTCOUNT ALL 60 MINUTES, PRICE
-REPORTROLLOVER AT 08:00 ON MONDAY
-file of rejection is to follow the error
DISCARDFILE E:\Oracle_Goldengate\V22232-01\dirchk\OGGdiscard1.dsc, APPEND, MO 50
TABLE HR. REGIONS;
TABLE HR. COUNTRY;
TABLE HR. LOCATIONS;
TABLE HR. DEPARTMENTS;
EXTRACT LHRDEV2
ID USER, PASSWORD GGS GGS
EXTTRAIL E:\Oracle_GoldenGate\V22232-01\dirdat\E2
DDL ARE MAPPED
-DDLOPTIONS REPORT
DDLOPTIONS ADDTRANDATA
DISCARDFILE E:\Oracle_Goldengate\V22232-01\dirchk\OGGdiscardE2.dsc, APPEND, MO 50
TABLE HR.JOBS;
TABLE HR. JOB_HISTORY;
TABLE HR. EMPLOYEES;
Data Pump - two pumps data configured
===========================================
-Data pump
EXTRACT PHRDEV1
-below passthru parameter to GG it would just move the data it
-are without required transformations
EXTRACT PHRDEV1
PASSTHRU
RMTHOST Alexander-PC, MGRPORT 7809
-RMTHOST 192.168.1.2, MGRPORT 7809
RMTTRAIL E:\GoldenGate\V22232-01\dirdat\P1,MEGABYTES 100
TABLE HR. REGIONS;
TABLE HR. COUNTRY;
TABLE HR. LOCATIONS;
TABLE HR. DEPARTMENTS;
-Data pump 2
EXTRACT PHRDEV2
GGS ID USER, PASSWORD ggs
-below passthru parameter to GG it would just move the data it
-are without required transformations
RMTHOST Alexander-PC, MGRPORT 7809
-RMTHOST 192.168.1.2, MGRPORT 7809
RMTTRAIL E:\GoldenGate\V22232-01\dirdat\P2, 100 MB
TABLE HR.JOBS;
TABLE HR. JOB_HISTORY;
TABLE HR. EMPLOYEES;
GGSCI (Françoise-PC) 18 > stats ext lhrdev1
Send request for STATS to LHRDEV1 EXTRACT...
Beginning of statistics to 2013-07-02 21:14:41.
DDL replication (for all tracks) statistics:
Lag time since Chkpt program status group
MANAGER RUNNING
EXCERPT FROM RUNNING LHRDEV1 00:00:00 00:00:00
EXCERPT FROM RUNNING LHRDEV2 00:00:00 00:00:00
EXCERPT FROM RUNNING PHRDEV1 00:00:00 00:00:00
EXCERPT FROM RUNNING PHRDEV2 00:00:00 00:00:02
Total statistics since startup extracted *.
Operations 0.00
Mapped operations 0.00
Unmapped operations 0.00
Other operations 0.00
Excluded transactions 0.00
E:\Oracle_GoldenGate\V22232-01\dirdat\L1 output:
Extraction of human resources. AREAS of HR. REGIONS:
Total statistics since 2013-07-02 21:02:05 *.
Total of 1.00 inserts
0.00 total updates
Total of 1.00 deletions
Total 0.00 releases
Total operations 2.00
Daily statistics for 2013-07-02 21:02:05 *.
Total of 1.00 inserts
0.00 total updates
Total of 1.00 deletions
Total 0.00 releases
Total operations 2.00
Hourly statistics for 2013-07-02 21:02:05 *.
Total of 1.00 inserts
0.00 total updates
Total of 1.00 deletions
Total 0.00 releases
Total operations 2.00
The most recent statistics from 2013-07-02 21:02:05 *.
Total of 1.00 inserts
0.00 total updates
Total of 1.00 deletions
Total 0.00 releases
Total operations 2.00
End of the statistics.
================================================================================
TARGET SYSTEM
================================================================================
REPLICAT RHRDEV1
ID USER, PASSWORD GGS GGS
-NOHANDLECOLLISIONS
AssumeTargetDefs
DDL INCLUDE ALL
DISCARDFILE E:\Goldengate\V22232-01\dirchk\OGGdiscardR1.dsc, APPEND, MO 50
Map of HR. REGIONS, target CF. REGIONS;
Map of HR. Target COUNTRY, CF. COUNTRY;
Map of HR. PLACES, target CF. LOCATIONS;
Map of HR. DEPARTMENTS, target CF. DEPARTMENTS;
REPLICAT RHRDEV2
ID USER, PASSWORD GGS GGS
AssumeTargetDefs
NOHANDLECOLLISIONS
DDL INCLUDE ALL
DEFAULT DDLERROR IGNORES RETRYOP
DISCARDFILE E:\Goldengate\V22232-01\dirchk\OGGdiscardR2.dsc, APPEND, MO 50
Map HR.JOBS, target HR.JOBS;
Map of HR. JOB_HISTORY, target CF. JOB_HISTORY;
Map of HR. EMPLOYEES, target HR. EMPLOYEES;
Lag time since Chkpt program status group
MANAGER RUNNING
REPLICAT RUNNING RHRDEV1 00:00:00 00:00:01
REPLICAT RUNNING RHRDEV2 00:00:00 00:00:06
GGSCI (Alexandre-PC) 16 > stats rhrdev1
Send request for STATS to REPLICAT RHRDEV1...
No cards active replication
DDL replication statistics:
GGSCI (Françoise-PC) 19 > all the news
Total statistics since replicat started *.
Operations 0.00
Mapped operations 0.00
Unmapped operations 0.00
Other operations 0.00
Excluded transactions 0.00
Errors 0.00
Retries 0.00 errors
Discarded 0.00 errors
0.00 ignored errors
GGSCI (Alexandre-PC) 17 >
Action of the host:
This message has been moved from the General Questions of the database space,
the location of GoldenGate, for better alignment of the section.
Tips:
There is no "Urgent" in these community user forums.
People will respond if they choose to.
There is no obligation that there is always a response to the request of a person.
If you have a problem in a critical business need, use your credentials to service contract and contact the company directly connect a support request ticket.
-
Photoshop CS5 crashing when trying to save and open files (need urgent help)
Hello
Recently, my photoshop CS5 played upward and often when I try to save files it will freeze to the point of crash and clicking on ok. Today too it crashed when I tried to open a photoshop file.
It's very frustrating because I'm a graphic designer and trying to complete an urgent task, but I suck because anything I do is save and I have to keep starting over. It is literally broke down about 40 when the day is over and I lose so many hours that I just haven't.
Please help me, it came out not the case and needs to be repaired emergency.
My as mentioned version is CS5 and I've updated yesterday with nothing doesn't.
My laptop is a Mac
If necessary info:
Model name: MacBook Pro Model identifier: MacBookPro7, 1 Processor name: Intel Core 2 Duo Processor speed: 2.4 GHz Number of processors: 1 Total number of cores: 2 L2 Cache Memory: 3 MB Memory: 4 GB Bus speed: 1.07 GHz Boot ROM version: MBP71.0039.B0B Version of the SCM (System): 1.62f6 Serial number (System): WQ0422P1ATM Material UUID: 92320237-011A-5454-96B7-28704CE335C0 Motion sensor sudden:
State: Activated Any help much appreciated.
I don't think I did something for it to start to happen, is it just came out of nowhere... I usually just do the same thing a few things with the program and also havn't changed files or even the computer.
Thank you.
Yes, you're crashing on a good bug known to MacOS.
Apple is still working on a fix.
But in the meantime, go run disk utility and repair your disks - which must repair the disk of the data structures and avoid the bug.
-
Urgent - help merged HTML projects - display in the same window
Hi all
As a result of the recent windows updates, I have all sorts of problems. My most urgent problems is as follows:
First of all it's in RH8 and yes I have updated to version 8.0.2 and project is ready to re - build cpd each time.
So I have a project of mergers as follows:
Parent project
project of the child 1
Draft 2 Collard, etc.
When I compile a project to help html with table of contents, and the parameters of source window unique default, if I click on a child of the project it is diaplyued in a separate window. If I then select another project in the parent TOC project, it is also displayed in a different window, but the window still has the legend of the previously opened file.
What I need that the end result is for my project output help HTML al display in the window even if I click on an element of the parent project, or a project of child item.
Please can someone advise dem how do I close a date limit and as usual, it seems that RH8 has let me down again...
Thank you
The author care
Hello
It seems to me that Colum needs more coffee, because the options cited have nothing to do with other windows. They have to do with the question of whether the displayed topic synchronizes with the table of contents and if table of contents entry is highlighted.
I think it has to do with creating a window of 'Global '. You change the names of the windows so that they understand Global.
The link below has more:
See you soon... Rick
Useful and practical links
Captivate wish form/Bug report form
-
Need urgent help - rtf Table boarders.
Hi, I have an urgent need.
I have a table, for which I'll put borders. Everythings works fine, with the exception of a single cell, where borders are repeat in a loop for each... I need that will be not be displayed each time. For all the other cells of the same requirement, it works fine. with the exception of this cell. I have to submit this report now and his rellllyy an emergency.
I can drop the xml model if you need. I got to understand the problem. Please help me.
I tried everything I could do.You sent the updated files
Maybe you are looking for
-
Best battery for Satellite U500 PSU9MA?
My PSU9MA satellite U500 - 00K 013 currently uses a battery of 3410mAh DC10.8V (model No.: PA3634U-1BRS) gives me a max of 2 hrs use before you have to plug it into the power outlet. I was wondering if I can buy a longer life for Satellite U500 batte
-
How to increase the folders (remembered) from 400 to 1000?
My PC don't remember size of folder settings. I understand that XP is set to remember 400 files by default, and then again, sometimes XP don't remember folder settings more. It is supposed to be a way to increase the niumber of record of 400 to 4000,
-
When you read an article on the web I have a circle with the 4 arrows to pop up on the page and it will be auto-faites scroll down? original title: auto-scroll
-
Firewall is blocking spotify error 101.
I can not connect on spotify. It says that I need to update a firewall like this it can block or, I need to change my proxy settings. What should I do and how I do it?
-
Reinstall Windows 7 after upgrading to Vista?
I have my old watch office that I've upgraded from Vista to Windows 7, and after 4 years I want to reinstall Windows 7 to start fresh. The Vista that was on it, I have the disc Version of OEMs and for Windows 7, I have the disk that was given to me b