WRT160N - V3 Xbox NAT strict issue

Xbox 360 NAT issues resolved! (WRT160N v3).

I followed the instructions in the link above, but also at least 20 other posts, but I always get strict NAT with a unique XBOX.  I think I tried all combinations and I can't understand why my situation is somewhat different.

Question - when I go to the STATUS, under the 'Internet connection', "IP address" tab, I see 192.168.1.64 (internal address).  I read somewhere that in other words, there is an another NAT also beyond my router. What is the problem?

This problem started when I replaced my (default) combination modem/DSL router by an old 2Wire-Homeportal-1000 s, with a brand new Motorola model 2210-02-1022 (modem only) of the AT & T store and combined with a WRT160N V3.

I tried all combinations of UPnP enabled, redirection port, serial port triggering and DMZ range.  I used a DHCP reservation to affect my Xbox a static IP address and checked that works very well.  But even in the DMZ with UPnP off, I get strict NAT.

I think I have to empty the Motorola + 160N and buy the current combo modem/router 2Wire AT & T, but I do not do that when I don't know for sure there will be more.

Others seem to have great success get this cleared up.  Can someone shed light on why none of these techniques work for me?

Thank you

I want to thank you because after endless hours trying to remove the XBOX 360 strict NAT son - your advice finally put me on the right track.

With my particular combination: AT & T DSL, modem Motorola + WRT160N-3 - Bridge mode did not work.  As soon as I put the modem in Bridge mode, the light of the Internet on the front does not to come.  Maybe, if I called AT & T I could find a way around it.  This setting seems to affect the PPOe connection to the router instead of the modem, but some PPOe setting I use (including by providing the user ID and password, etc.) brings me an Internet connection.

What worked was in the modem settings.  There was no obvious parameter to enable/disable NAT, instead, it reads: "Let device LAN share Internet address?   Choice: "No, use the private IP address", "Yes, use the public IP address.  This is the power switch modem NAT and it must be set to Yes (default is NOT which is what created the 2nd NAT).

Even in non bridged mode, with the removed modem NAT, the NAT router and other work now setting.  I could put the Xbox successfully in in the demilitarized zone.  The idea is, in the STATE of the router tab, you see now a public IP address instead of the internal address of the modem.

WOW that was difficult and time consuming to get to this point!

Tags: Linksys Routers

Similar Questions

  • NAT Strict an Xbox will switch to open

    Linksys Model: Linksys EA6350-4 has

    I set up a DMZ with the correct settings, giving both my cable, linksys and xbox, but it is still as strict. When I tried port forwarding, my wiFi is going to *, and my xbox is still strict. I would appreciate some help with what I have already reset my router (that I just bought two days ago) to factory settings about 4 different times already.

    EDIT: It is also on a wired Xbox.

    Your ISP modem has NAT if your in a double NAT condition that is not recommended:

    http://NA.SMC.com/products/residential/voice/smcd3gnv/

    If the modem cannot be filled, then see if the modem has a DMZ option and enter the IP address of the router gets the modem and put it in the DMZ modems. Don't forget to disable all other filters and firewalls on the ISP modem.

    Configure the router to 6350 for release of Port Range:

    https://community.Linksys.com/T5/wireless-routers/open-NAT-problems-with-Xbox-one/TD-p/944929/page/2

    Configure an IP address for the xbox to 192.168.1.199 on the router, and then reboot the router.

    Performs a Factorty network setting reset on the xbox. Turn the xbox off then back on NAT status then chk. You should get OPEN, but if the ISP modem any treatment then you may see moderate...

  • WRT160Nv2 Xbox Live Nat Strict and need to open NAT.

    So I have a WRT160Nv2 and I'm trying to get my nat to become unstrict for xbox live. I tried port forwarding which did not work. I tried this site http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread.id=122065 and who doesn't (I don't have an xbox 360 btw). Nothing has worked for me and whenever I mess with something that it screws to the top of the internet, so I put up the previous default values. I know how to access my router I just need to know what to enable, disable, or add to the router. Any help would be great. Thank you very much.

    Uncheck all options trigger Port and try the Port Range Forwarding...

    Port Range Forwarding-

    Application: xbox

    Start port: 53

    End port: 3074

    Protocol: the two

    IP address: 192.168.1.20.

    Check the enable box and save the settings.

    On the Security tab, leave the block anonymous requests disabled and change the MTU in 1452 under the Configuration tab.

    Click the status tab, and take note of DNS1 and DNS2 address...

    Goto the network settings on XBox and IP address settings and select manual IP settings and assign the following operations on your Xbox: P address:-192.168.1.20, subnet mask:-255.255.255.0 default gateway:-192.168.1.1...

    Also assign addresses DNS on Xbox
    Use DNS1 and DNS2 addresses you took note of the primary router as secondary DNS & DNS status tab for the xbox...

    Turn off your modem, router and Xbox... Wait a minute...

    Connect the power supply to the modem first, wait a minute and plug the router power cable, wait another minute and turn on the Xbox and... test it connects...

  • Problems with WRT160N and Xbox 360 - please help

    Hello

    I recently bought a WRT160N router and when I play games online (Halo 3 or Modern Warfare 2) it takes about 10 minutes to find a game then that in the Hall. I didn't put in the door or disconnected from my profile, there's just a lot of time. It says that my NAT type is open. I've isolated the problem is the router because if I plug in an ethernet cable from the 360 to the DSL modem I find games instantly. I examined the port forwarding and open ports on the 360 and specifically for modern warfare 2 and it was actually my NAT type go as strict, ironic. I have spent 5 hours trying to mess with this and can't seem to make it work right. If someone could please help me on the settings or have any other ideas that would be greatly appreciated.

    As your ISP is a provider DSL, most providers DSL has setup their modem in DHCP Mode, so your Modem acts like a router. So, right now, your Setup is NAT behind NAT. So if you try to open the Ports on your Linksys router it does not work as your Modem Hangs only ports.

    So the best way to work is to convert your Modem in Bridge Mode and it will solve all your problems.

  • My problem with the BEFSR41 & Type of NAT Strict

    This has probably been discussed so many times, but I am at my wits end. I have tried almost everything on the web on how to get a NAT for this router and nothing has worked. I try to get an open NAT to connect and join some games that host friends on the LIVE service. There are, I could join their games without a problem. Now, for about 3 months now, I can not join their sessions. She'll tell me that they are reachable, then tell me that the sessions are no longer available if I'm trying to reach. Cannot join their parties either. Strange thing is that, after a while I'll be randomly able to reach just 1 of their lobbies and hear only that person. I'm starting to think that I will always have this question. I changed a lot of things in the router I just reset it to the factory and compatible UPnP settings. Is that what I can do to fix this? I am desperate at this point. Sounds stupid, but it really gets to me. I can't understand for the life of me why I can't change.

    EDIT: I should probably say that the problem is with an Xbox 360. The network settings are now automatic, as manual did not help either.

    Thank you for your time and I look forward to hear what you all have to say.

    David.

    You can follow this link and it will help you set up a static IP address on the XBOX.

  • Open with a Xbox NAT problems.

    When I got my 1900ac I used Media Priortization to get NAT open for Call of Duty Advanced Warfare on my Xbox One. prioritize the Xbox. It worked fine for about 6 months until what I changed my operator of cable/net of Nextech in Ks. This company uses the 1900ac to connect its system to all it's customers (since I already had one they use mine). Unfortunately, I am unable to get an open NAT in this game I tried almost everything, NAT forwarding, triggering, prioritization of the media. Support of NexTech & Xbox Live support, useless. I tried Portforward. com, nothing. Redirect port 53 breaks the connection to the network & making the static ip address change for Xbox has not helped. Almost everything I looked at seem obsolete & I am at my wits end. It would seem by now Linksys should have available solutions, any ideas?

    Chin_pamz13 thank you very much for your answer. I tried to check if my modem had a public or private ip address, but I don't know how to do this; I read on double NAT elsewhere. Nevertheless, I think I finally found a solution that seems to work so far. I went to the website "tech - recipes.» com "& found an article, 'Xbox one open NAT' by Aaron St. Clair.» I tried his first suggestion regarding the port of release, with additional ports I had'nt seen before. Who has not worked for me so I followed his instructions to the Xbox in the demilitarized zone & it works! I think that my problems from before were the result of bad to configure the static ip address for my router & Xbox. The previous instructions had me change the ip in the console with the router. Aaron said does not do in the Xbox, leave the router to do the work, it's supposed to do & make sure the console settings are on automatic. In the router in the DMZ, I was'nt sure how to proceed, but at the bottom is a section called list of reservations DHCP; clicked on this, XboxOne saw, clicked on that & he filled the top for me MAC address. Then I went to network settings Xbox, advanced & clicked settings on "automatic" to the ip address, subnet and DNS. I checked the connections mutiplayer, toured "hold bumper & trigger buttons" & finally got a NAT open; pulled up to cod Advanced Warfare & also got open NAT it. I could have screwed up when I did the port triggering, but given the difficulty of the DMZ seems to work I'll let things alone. Hope this helps anyone else having problems NAT open.

  • WRT54G2 show me customers & xbox 360 lag issue

    I just got a wireless router WRT54G2 about 2 days ago, and after having switched from Netgear, I badly due to find some settings.

    I have 3 computers on my network and 1 Xbox 360. One is one laptop (WiFi), the other 2 desktops (directly connected).

    They do not appear in the DHCP Clients. I get lag issues on my Xbox 360 and I want to see if its using the IP address I posted, since I'm portforwarding. I decided to go ahead and manually configure all computers to have a static IP address.

    If the DHCP Clients cannot be resolved, is there another way to see that if the Xbox is using the IP I assigned it?

    Triple post, oh gosh. I fixed it, well done linksys. I just updated the firmware, I just bought it didn't this necessary update already! But Portforwarding and UPnP are on, if all goes well no conflicts!

    Thanks for your GENEROUS response. :]

  • 8.4 ASA using NAT VPN issue.

    Hello

    I'm working on a customer site and they have a problem with one of their VPN (we have other works well), but it is a major issue and I think it's because we use manual NAT and NAT of the object on the same server for different things.

    Traffic between indoors and outdoors:

    It works with a specific manual NAT rule of source from the server 10.10.10.10 object

    Inside

    SRC-> DST

    10.10.10.10-> 1.1.2.10 1.1.1.10-> 1.1.2.10 SNAT = VPN =-> 1.1.2.10 1.1.1.10 1.1.1.10-> 1.1.2.10 <3rd party="" fw="">

    It works with a specific using the NAT on the server of 10.10.10.10 object

    Remote

    SRC-> DST

    1.1.1.10-> 1.1.2.10 1.1.1.10-> 1.1.2.10 <3rd party="" fw="">= VPN =-> 1.1.2.10 1.1.1.10 1.1.1.10-> DNAT 10.10.10.10

    If we have the manual NAT and NAT object it does anyway.

    So the question is (as I am new to zip code 8.3 ASA) should not mix the 2 types of NAt and look at configuring it all with manual NAT or NAT object?

    With the NAT object out it does not work as it is taken in ouside NAT inside all:

    Dynamic NAT (inside, outside) source no matter what interface (this NAT to 1.1.1.1 then does not match the card encryption for VPN)

    and I tried a no - nat above that, but that does not work either.

    Straws and hugging come to mind try to configure a different config. Any pointers in the right direction would be great.

    Kind regards

    Z

    Hello

    I'm not sure that installing even with the explanation. Each NAT configuration I did for VPN used Section 1 Manual / NAT twice.

    You have configured the rule by default PAT that you use as Section 1 NAT rule. NAT rules in the new software are divided into 3 sections

    • Section 1: Manual / twice by NAT
    • Section 2: Purpose NAT
    • Section 3: Manual / double NAT (moved to section 3 using the setting "auto after")
    • The Sections are passed by from 1 to 2 and 3 in order to find a match.

    You should also notice that the Section 1 and Section 3 NAT has "line number" similar to the ACL parameter type. So if you have a default existing PAT rule configured for Section 1 and just add another Section 1 NAT rule without line/order number (VPN NAT) then it will just fall under the existing rule, making the new useless rule.

    I would advice against the use of the rule by default PAT as Section 1 NAT rule. Finally, this means that you be constantly watch and edit its configuration when you try to configure more specific rules.

    As a general rule 3 of the Section the PAT above default configuration would be the following

    NAT (inside, outside) after the automatic termination of dynamic source no matter what interface

    This would mean that you need to remove the old. That would mean as naturally as the change would temporarily dismantling all the current connections through "inside", "Outside" while you change the NAT rule format.

    If after this configure a NAT twice to the VPN (wihtout the setting "auto after"), it will be the rule in article 1 while the default PAT will be Section 3. Of course, Section 1 will be matched first.

    I'm not quite sure of what your setup of the foregoing have understood.

    You're just source NAT?

    I guess that the configuration you do is something like this?

    network of the LAN-REAL object

    10.10.10.0 subnet 255.255.255.0

    purpose of the MAPPED in LAN network

    1.1.1.0 subnet 255.255.255.0

    being REMOTE-LAN network

    1.1.2.0 subnet 255.255.255.0

    NAT static destination of LAN LAN-REAL-MAPPED Shared source (indoor, outdoor) REMOTE - LAN LAN

    If the network 1.1.1.0/24 is supposed to be one that is connected directly to your "external" to the format interface may need to be anything else.

    -Jouni

  • Design site to Site VPN w/NAT traversal issue

    Hi, I have a number of site to site VPN that end on a PIX. I intend to migrate these VPN to a router that sits on a demilitarized zone connected to the PIX. Before doing that I'm going to set up a private network new virtual to end on the router but I also need than VPNS that end on the PIX to be not affected.

    If I configure NAT traversal on the PIX, affected my other VPN?

    Thanks in advance

    DOM

    Hi Dom,

    Why do you want to configure NAT-Traversal on PIX, if you wish to terminate your VPN router (which is on the DMZ).

    Do you do any NAT on PIX thru the router?

    If you want to configure NAT-Traversal, it must be configured on the end (on the router in your case) devices.

    Example:

    When a user with Cisco client or Cisco router behind NAT wants to connect to another device (such as PIX, ASA, or router) NAT - T must be configured on the machine (which will be the PIX or ASA)

    Hope that helps.

    * Please indicate the post

  • 8 of Windows and Xbox 360 connectivity issues

    Since the update to Windows 8, I'm having problems with streaming of media to my Xbox 360.

    Previously, I had windows 7 and has been able to stream multimedia content (movies and music), or via the Media Center windows, or by connecting to my PC via the Xbox drive and folder navigation.
    Since the update to Windows 8 Media Center not connecting, he used even together upwards. I enter the 7 digit code set up and my computer says it cannot establish a connection. I tried to connect to my PC through the Xbox and when it can not connect.
    In the list of devices, the Xbox is displayed and even so capricious it shows that the Xbox is online and I am able to stream on my 360 using the video app and selecting "send to device" and selecting the 360. Unfortunately, this will randomly cut everything playing and yesterday would not work?
    I am running windows 8 Pro 64-bit with media center installed. I am connected via WIFI to my router, but my Xbox 360 has a wired connection
    Please help, I'm getting so frustrated that I spent a fortune on upgrading my PC and OS lose all the features, I already had
    Thank you very much

    Copy and beyond music in your cloud files, this makes select all your music and right click on the files you want to play or your xbox. Scroll down and select the option 'include in the library', and then click music.

    As says Peteanon go to windows medial player and make sure that the name of your xbox is checked, and then click Next until you get a password to get into your local network share there are three pages. When you reach the last click on print password and instructions. Follow the instructions on how to configure a password sharing between your xbox and pc.

    for the last two days that I had a connection problem after that I followed this method my music perfectly.

    Note: I have an xbox 360 and I am sure that it will work with the xbox one, but it should make note.

  • NAT on Xbox problems

    NAT strict rest type no matter what I try.
    I gave up on the phone and chat support live if I'm hoping someone on the forum can help out me. After spending 2 days with support from netgear and nothing...
    (Oh you will love this. The last support person I spoke with told me to change the settings and firmware update and guess what! My download speed is below 0.6mbps now)

    ISP: Comcast (xfinity)
    Brand modem: Arris
    Router: Netgear Nighthawk AC1900
    Firmware version: V1.0.2.194_1.0.15

    Address reservation is configured for an Xbox (192.168.1.3)
    Filtering NAT: open
    SIP ALG: disabled
    QoS upstream: on
    Port forwarding: (all listed ports use the same range of ports for internal)

      Yes, all ports are using my IP xbox

      UPnP: on
      DMZ server: Default 192.168.1.0

      Any ideas?

    Do not use the DMZ and port forwarding at the same time on one device

  • Strict NAT with a BEFSR41 router

    So I play frequently on my xbox 360 and I like to browse my computer when I'm waiting for a match. With my old router, same brand and model, all I had to do was do port forwarding with the ports recommended on xbox.com and enable upnp and I had no problems to connect to games, joining friend games or assembling them mine.

    So when I got my replacement router I have activated the same options as before but kept getting the strict NAT message when I start a game and none of my friends could join my game and I couldn't join them. So I enabled the DMZ and clone the MAC address of xbox 360. He got rid of the NAT strict message but I noticed a significant drop in the speed of the internet, yet none of my friend could join my game and I couldn't reach them.

    So I had to unplug the router and connect the xbox directly on the modem I have while waiting for the replacement router and I could do all the things as before. So it leads me to believe that there is a problem with the router. I have a linksys BEFSR41 v. 4.3 router and modem motorola with a DSL connection.

    Any advice or ideas would be greatly appreciated.

    Yes, you are right that if the modem acts as a router, it should be filled if you want to connect to another router... If your modem is full you will not get the internet light on your modem (it will remain off)...

    Once you configure the modem in Bridge mode full you must configure the type of internet connection of your router in PPPoE and enter the correct user name and password provided by your Internet Service Providor (ISP)... Once done, click on save settings...

    Click the status tab and search for an IP address, if you get 0.0.0.0 for the IP address click on the Connect button and weait... Power Cycle your modem and your roputer for a minute and see if you can go online... Once you are online, you can make the settings as shown in the previous post for your X - Box and it should connect...

  • WRT160N V.2 / disorders of the Xbox360

    I have zero chance to get my Xbox360 NAT change out of NAT Strict.

    I tried all the methods that I could find, some of whom have been stupid probibly.

    I'm using a WRT160N V2 router with no modem.

    Everything here is for v1 and v3 and I doubt im the only one with this problem.

    Help! (please)


  • access to the xbox live

    my email account parental xbox live is inactive because the person has changed his name and it closed so I can't accept the new conditions. Please you can reactivate this account of * address email is removed from the privacy * by changing the name of the mother to * address email is removed from the privacy * please?

    It is a forum for peer-to-peer of users. We cannot reactivate whatever it is. You work with Xbox on this issue.

    FOR ANY XBOX PROBLEM:

    XBox - Support
    http://support.Xbox.com/en-us/pages/default.aspx

    XBox - Contact us (support)
    http://support.Xbox.com/en-us/contact-us

    XBox - Support Forums - and my XBox (top-right)
    http://forums.Xbox.com/

  • What is my email for my account xbox live so I can download on my xbox.

    the gamer tag is LBC THUGZTA 187

    It is a peer-to-peer forum. We do not have this information. In all cases, you will need to work with Xbox on this issue.

    FOR ANY XBOX PROBLEM:

    XBox - Support
    http://support.Xbox.com/en-us/pages/default.aspx

    XBox - Contact us (support)
    http://support.Xbox.com/en-us/contact-us

    XBox - Support Forums - and my XBox (top-right)
    http://forums.Xbox.com/

Maybe you are looking for

  • sharing two iphones

    Hello :) Please bare with me and I apologize if this is a stupid question, but I'm not very irritable. I have an old iphone that I gave to my foreign friend. If we use the same Apple ID which will be exactly connected between our two phones? How do I

  • New laptop and receive an error message that the D drive is full. What can delete off of it?

    I try to understand what I can remove drive D, so that it is more complete. I know it's for the restoration of my computer or something like that, so I don't know what I can remove it. I looked on the player, and most seem to be what I have on it. Ho

  • HP Pavilion dv7 no sound

    Hello recently I hv plugged a mini speaker for my dv7 and afterthat no sound, even I delete the mini speaker of my laptop. What can I do with it? Here are some details on my laptop: model: hp Pavilion dv7 window version: vista 32-bit hope that this p

  • iTunes error message R6034 C:\Program Files (x 86) iTunes\iTunes.exe

    I'm unable to access iTunes. I get runtime error! As above. It says ' an application has made an attempt to load the C runtime incorrectly library. I moved all the dll files to desktop as suggested and uninstalled and reinstalled iTunes, but I always

  • Sony Motion Eye Driver

    I have a problem with finding the driver for a Sony VAIO VPC - y216GX Motion Eye Camera. I used the Automated Troubleshooting Services Fix - It Utility, but it cannot find the driver. Sony has said that it is a Windows problem. What gives?