WRT1900AC cannot see Wireless Bridge

Similar Questions

• Satellite P300 and Win7 - cannot see wireless networks

  Hello

  I have Toshiba Satellite with Win7x64 and I bought on eBay an AR5008.

  If I boot Linux I can connect to wireless networks.
  However if I boot in win7 that I can't even see wireless networks. If I run diagnostics I get the radio is turned off.
  Even with ConfigFree I get the same message, even if the switch on the front of the laptop is on.

  What can I do? I tried all the drivers!

  Hello

  Normally, you can enable or disable the WLAN connectivity by using the equipment and the FN + F8 key combination switch.
  Did you check that?

  I guess for the FN + F8 key combination you need value-added package. You can download it on the Toshiba site.

  Last but not least, works WLAN with preinstalled OS from Toshiba?

• Cannot see wireless LAN available on Tecra A5 but ok with Tecra M5

  Hello
  I have the following problem:
  I have an access point (DWL-3200AP) DLink wireless set up in my office.
  On my laptop, I can see my WLAN and I'm able to connect with my Tecra M5.
  I can see the WLAN on the tool graph configfree.
  Now the problem... I bougth a Tecra A5 for my boss, everything works well... The radio is active...
  OK wireless card... BUT I don't see the WLAN... can't find it...
  I've checked everything but I do not know why...
  Is someone can help me?
  THX
  Math.

  I suggest you check the settings of the router.
  To my knowledge a lot of WLan routers supports a WLan option cache.
  In this case, the WiFi network is not visible and you must know the name of the WLan to search.
  I think you know the name of the WLan so I recommend entering the wireless network connection properties, and then selecting the wireless networks tab.
  There you can add preferred networks. You must enter the WLan name and encryption.

• Equium A200-15i: cannot see wireless network adapter

  Hi all.

  I tried to install the drivers on my laptop wireless without a bit of luck.
  My network card works, and I can connect to the internet via ethernet. But wireless doesn't work at all.

  I checked under network adapters and Device Manager, it shows realtek fast ethernet nic and 1394 network adapter.
  In the other devices section, it shows Ethernet controller... I tried to score for the drivers that I downloaded but it says "no new pilots could be detected.

  I hope someone can help
  (also - wlan is enabled in the laptop, but nothing happens - and it only shows my connection to the local network in network connections)

  I see that your wireless network card is not mentioned under network adapters in the Device Manager and so I m 1005 sure that Wlan card driver was not installed.

  I think that you were unable to install it because you used all just a bad driver!
  Equium A200-15I belongs to the * PSAE2E * series.

  Please check that you have chosen the right notebook series and downloaded the correct driver.
  As far as I know this unit should support the card of XB63L Wlan Atheros 11 b/g (13ch).

  Good luck buddy

• Cannot see wireless networks

  Hello

  I have checked through some of the forums, but couldn't find an answer that helps me, so I post here.

  I am running Vista Home Premium SP2.

  Until this morning, my wireless worked fine. Today, my laptop is unable to connect to any wireless network. I make sure that my router works fine (I am connected via my phone), my device driver is showing no problem in device manager, and my wireless switch is turned on. All other configurable in Control Panel Network is set to automatic.

  Any help is appreciated.

  Thank you.

  Hello

  Maybe this can help.

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  If all the foregoing is OK and it does not connect to the wireless router. Journal from any computer that is or may be connected to the wireless router with a wire, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security .

  When the work turns on the Wireless security.

  * Note, people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  ---------------------

  Stack TCP/IP work should look like.

  TCP/IP and its variables usually look like this.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  --------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Vista: Cannot see wireless networks - I know they are there.

  I'm contracting at Microsoft and just installed the company issued IT Vista. Everything works fine: I joined the appropriate domain and can access all internal servers and the Internet with the ethernet cable is plugged.

  However, I don't know how to jump on the wireless network. My host OSX (10.5.6), I see the Microsoft WLAN airport is accelerating. Connection to the WLAN MS requires that I am connected to the correct field in Vista (I am), but I do not see the wireless networks - as if there is no such thing as a wireless NETWORK card.

  VMWare Tools are installed, and Device Manager shows my NIC is "Intel Pro/1000 MT Network Connection. I use the connection of NAT in Fusion. Diagnosis of the problem in Vista, he said: it is not an installed wireless device.

  Connection to the WLAN MS requires that I am connected to the correct field in Vista (I am), but I do not see the wireless networks - as if there is no such thing as a wireless NETWORK card.

  It does not exist. Take a look at: VMware Fusion (menu bar) > help > VMware Fusion help > Machine virtual Basics > virtual hardware specifications

  If you need to post by connecting to WiFi since in Vista then you will need to install a 3rd party USB WiFi NETWORK adapter in the Virtual Machine in Vista.

• Satellite Pro L40 with realtek card: cannot see wlan Vista networks

  Hey

  You just bought the L40 (Realtek card) and it cannot see wireless networks. The diagnosis of Vista, is that the wireless adapter must be turned on. Then, it will fail to start. Function key and F8 (wireless on/off switch) does nothing.

  The wireless router is well - connected to an XP machine. I can connect to the router without a problem by using an ethernet cable.

  Running on the latest Microsoft drivers.

  Pointers much appreciated.

  Thank you
  Frank

  Hello

  you turned on the wireless the case switch on "ON"? Maybe you forgot this one, and this is perhaps the reason why it won´t work.

  Please check and make sure that you then use the FN + F8 switch.

  Would appreciate your comments on this...

  Welcome them

• Intel WiFi Link 5100 network card - cannot detect wireless networks

  I have a HP Pavilion dv7-1270us. My wireless card is an Intel WiFi Link 5100.

  Running Windows Vista 64 bit, Ubuntu Linux, Linux Mint and Fedora Linux (various versions, all), the wireless works fine. My desktop computers to work with wireless cards to connect to the network work very well, and all computers (except mine) to connect to my home network very well; which means that it is not a problem with wireless networks, or with my network card. I try to manually connect to the network, but it can't find it. Diagnosis requires that the card is disabled, and that I should turn it on via the switch on my laptop running: fact.

  During the installation of Windows 7 64 bit, I cannot see wireless networks (and therefore unable to connect). Re-formated and reinstalled again, check the wireless connectivity between each batch of Windows Update, but it has never worked.

  I downloaded the latest drivers from Intel, via Microsoft Compatibility Center (version 15.2.0 driver).

  There is no system restore option because he has never worked as a first step, except in all other OS, I got on the computer. Microsoft Compatibility says the map is compatible, then Device Manager shows no problems. The network adapter is active via switch on my laptop.

  Happy that you guessed it sorted!

• WiFi AR5007 802. 11 b / g adapter cannot talk about bridge WET11 Wireless on the same subnet

  Hello

  My HP Compaq Presario C700 VISTA laptop (a AR5007 802. 11 b / g WiFi adapter) and the printer are on the same subnet. The laptop is WiFi connected to my WRT54G2 router/switch and the printer is connected to the workgroup switch that connects to the router via the LinkSys WET11 Wireless Bridge.

  The installer works fine for over a year until he was there when my VISTA does not see any PC on the Working Group 3 weeks pass including the printer. However, the WAN access is not affected.

  I did the filming of following problems (in order):

  1. check the network settings on the laptop VISTA (x.x.x.29) and (x.x.x.201) printer and all look kosher.    (All my PC including notebook computer and printer have IP STATIC)

  2. check the router and the parameters of bridge and fines all eyes (router - XXX1, bridge - x.x.x.140).

  3 Ping printer, bridge, and other PC and received messages "Destination Unreachable Host" or "Request timed out". Although all are on the same subnet. Pingée router is OK.

  4 remove and re-add the wireless profile and tried to connect again. Same problem, no joy!

  5 started VISTA in safe MODE with NETWORK. Once again, the problem has persisted but at least eliminated applications as a potential source of problems.

  6. recycled power switch/router/workgroup bridge. No joy!

  7 WiFi connected other laptops to the same router (WRT54G2) and can ping other PC and printer END.    This means that the problem is limited to my VISTA laptop.

  8 given that the problem is on my VISTA and applications are not the source (see #5) of the problem, then probably the AR5007 802.11b.g wireless network card driver is original so I downloaded driver at HP and installed with version 7.3.201.25.  Problem is persistent...  Arhhh!

  Could there be something else that I missed? Can someone please help.

  Thank you

  You are the very welcome, John.

  Yes this driver will work fine on Vista Home Premium.

  According to the notes on the driver, it can just be run without uninstalling the current pilot you have on there now.

  After executing, you can confirm it 'takes' by going into Device Manager, expand network adapters, click the atheros wireless card, click the driver tab and you should see the installed version 2011.

• wireless client cannot see wired - WAG320N

  Hello

  my modem/router WAG320N works fine but the wireless client cannot see wired and vice versa. they are in the same network (192.168.0.), using the same 255.255.255.0 mask, same workgroup firewall and Yes to enable all packages in and out. IP addresses are DHCP form.

  Internet sharing works fine, but when im trying to play any game on LAN wireless clients peuvent see their car but not wired. when im trying to client ping wireless from a wired machine it does not either.

  What is intresting in a DHCP reservation or the ARP table (in router configuration) I can see cable and wireless customers. but still they do not see each other.

  help pls!

  Hi again,

  I went to PC World and they exchanged this WAG320N to another. but this time I went to ASUS RT - N16 and so far all is working correctly. I know its missing adsl modem but got usb 2 and a print server.

  Sorry cisco...

  thx for your help guys!

• WRT1900ac - has no Config - error unexpected 2117 wireless bridge

  I'm having a problem connecting 2 routers together in Wireless Bridge mode WRT1900AC.  I followed the instructions here to step 7 (Clicked "Yes" to the "Warning" screen), and then I get this error:

  Unexpected Error
  
  2117
  
  We've encountered an unexpected error. If the issue continues, please visit our Technical Support site.
  
  Details
  
  /jnap/router/InitiateWirelessConnection -- Status: 200 OK Date: Sat, 18 Apr 2015 05:22:03 GMT Server: lighttpd/1.4.34 Connection: close Content-Length: 87 Content-Type: application/json; charset=utf-8
  

  

  This router is brand new.  The only things I've done are:

  1. Perform a router unboxing conversion
  2. Ignored configuration wizard
  3. Try to configure wireless bridge mode
  4. Received the error saying I need to reset the router to the factory settings
  5. Reset the router to the factory with the red button settings
  6. Router connected directly to the link upstream (cable Modem)
  7. Through the Installation Wizard
  8. Update the Firmware to the official version: 1.1.8.164461
  9. Has crossed the Bridge wireless installation Instructions here
  10. Got to step 7
  11. EU 'unexpected error 2117.

  I retried again and got a different error:

  

  I thought I would add another update here, given that the issue has been isolated and fixed:

  It turns out that plugging in the Comcast cable on the floor was very old, had a longer cable length, and was also on a split bar.  Called Comcast to help solve our problem, and they were able to test the intensity of the signal on the line.  Signal was not reliable on the cable on the floor, so we moved the modem more near the source of moving the cable (don't run, no separator, the best signal of shorter cable).  Upstream of the modem connection was immediately more reliable, moving router downstairs gives the best WiFi coverage for the rest of the House.  I have decided at this time that the extra router was not necessary and referred.  So, Detective Conan... problem was double: bad signal on the incoming line from Comcast and bad location for WiFi router upstairs.

• Network Magic cannot discover a "BEFSR41" router behind a "WET610N" wireless bridge

  Just upgraded to a WRT610N 2 version in my office.  He pulls an IP address from my cable router and distributes IP addresses (this is setup for DHCP) without problem.  I need to extend the home network to another part of the House so I took 2 x WET610N wireless bridges.  Since many devices will have to use the bridge I'll recycle my BEFSR41 as a switch.  I have the router configuration and bridge; the bridge connects to the port "uplink" on the router, and the DHCP has been disabled on the router.  But when I run Network Magic BEFSR41 router cannot find the other side of the bridge.  Any ideas?

  You need this post in the section Network Magic from this forum.  If the router acts as a switch, it will be transparent and not e seen.

• Received my brother in laws laptop cannot connect wireless, although I can of my own laptop. Trying to connect through the new laptop, I do not see even my own network.

  Received my brother in laws laptop cannot connect wireless, although I can of my own laptop. Trying to connect through the new laptop, I do not see even my own network! What I'm missing here? I'm sure it's maybe something simple, but for the life of me! (When my brother-in-law used this computer, he only uses it through dialup (!), he lives in a remote area). With the help of Vista, and when 'Management of connections' I see my network...

  original title: cannot connect wireless

  Hello

  ·         You get the error message?

  Method 1:

  I suggest you update the drivers for hardware connected to your computer on the Web site of the manufacturer check if it works.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Also, follow the steps in troubleshooting section and check if that helps:

  In the Windows wireless network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wireless-network-connection-problems-in-Windows

  Check out these links and check if that helps

  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-wireless-network

  See also:

  Solve problems with computers not appearing is not in the network map

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-computers-not-appearing-on-the-network-map

  Hope this helps

• Unable to join a homegroup Windows 7 with a network that spans a wireless bridge

  I have two Windows 7 machines that are at the ends of the face of a wired LAN network which connects via a wireless bridge and I am unable to get Windows 7 machines on each side of the brdige to connect to a homegroup created across the bridge.  Perhaps to better illustrate what I mean, here's my network configuration:

  Wireless router:
  Machine from Windows 7 1 (LAN wired to the router)
  Windows XP machine (for LAN cable to the router)

  Wireless Bridge (connect wirelessly to the wireless router):
  Computer Windows 7 2 (LAN wired to the bridge)
  PS3 (wired LAN to the bridge)
  TV (cable LAN to the bridge)

  I use the bridge wireless set up so that I can connect LAN devices wired to the wireless bridge so that they appear to be on the same local network as all other devices on the wireless router (stops to have at home and the bridge wire wireless allows me to expand the scope of all wireless devices I might have).  While all the machines can meet without a problem and I can't even set Windows Media Player to stream video to the PS3 and the TV through its capabilities of DLNA, Windows 7 network mapping server shows not the systems connected to the other end of the gateway wireless as being on the same network (although it shows them); so Windows 7 Homegroup does not see other machines as being on the same network.

  The only thing I can think to do with limitations in TCP/IP regarding a wireless bridge, from the perspective of wireless router all connected to the wireless gateway devices appear to be a device (they all appear under the same physical MAC address as the device only "wireless" that connects to the network is the wireless bridge - who just happens to have three other devices connected to it) even if they are assigned to different (numbers) IP that are in the same subnet, etc.).  So I guess what I'm wondering Windows 7 has a limiation to recognise the devices connected via a wireless bridge?  Has anyone else encountered this problem and found a work around?

  Thank you.

  I had this same problem (unable to connect to a Windows 7 homegroup) on Windows 7 (64-bit) PC behind a wireless bridge using a D-Link DAP-1522 to a D - Link DIR-655 residing on the main network.

  The solution that worked for me was to allow for the "'wireless MAC CLONING ' with 'Source MAC = Auto" on the DAP-1522. "  It also had the beneficial effect of the side to fix a problem on PC behind the bridge where control Panel\All Control Panel Items\Network card cannot display all the network devices.

• S75-b7218 Windows 8.1 satellite cannot see the bluetooth headset

  Satellite 8.1 Windows cannot see the Philips SHB5500 bluetooth headset.

  Driver: Intel (r) wireless Bluetooth (r)
  2014 08-12
  Version: 17.1.14342

  Help! Please, I beg you!

  Laptop certainly supports BT 4.0
  The question is: have you enabled the BT correctly in 8.1 parameters to win?

  Another question: have you tested the BT headset as part of another device?
  I mean, it is possible that the helmet is not working properly.