WRT54G connection interruptions

Similar Questions

• My Eudora mail then error downloading mails connection interrupted due to timeout waiting or any other breach (10053)

  Original title: error 10053

  My program of email Eudora (Version 7. 1 0. 9 paid mode) has recently stopped downloading mail but always send OK.

  The error message that happens almost instantly, reads "connection interrupted due to timeout or other failure (10053).

  My ISP insists it is my machine (OS = Windows7)

  I tried various trade programs to solve the problem, including the PC Cleaner and ReImage, no avail. Can anyone help?

  Hello

  The question you have posted is related to Eudora electronic mail and would be better suited in the Eudora e-mail community. Please visit the link below to find a community that will support what ask you:

  http://www.Eudora.com/techsupport/online.html

  http://www.Eudora.com/techsupport/win/

• If my connection interrupted by the ISP, my connection broadband (PPPoE) on my windows 7 freeze and it does not cut, and he does not answer to disconnect click.

  If my ADSL connection disconnected by the provider of the connection on my computer freezes instead of disconnect!

  As the title suggests, if my connection interrupted by the ISP (for example: Internet service provider who use dynamic IP automatically disconnects after 24 hours permanent connection), my connection broadband (PPPoE) on my windows 7 freeze and it does not cut, and this isn't answer to disconnect click, even if I uninstall the Ethernet card, keep the connection.

  Everything else works fine, and the only way to connect to the Internet is to restart my pc.

  Also if the connection is disconnected due to a traction cable or ADSL Modem power connection broadband (PPPoE) on my PC disconnect normally without any problems and I can reconnect without any problem.
  any help with this.

  Hello

  PPPOE software th whole arrangement never worked well from the first day more than 10 years regardless of the operating system.

  So most serious DSL carriers actually give free Modem/Router so that authentication would be by the side of the router WAN.

  They give it for free for phone support for this problem cost them more than the $10 adds the router to the Modem

  For example, get a router, simple routers in the United States are sold for less than $15.

  Router solved the problem PPPOE provides, security with NAT firewall, and stream DSL is actually faster than with authentication of software.

• WRT54G connected to a DIR-655

  Hello, I need help because I searched and found nothing. I use my DIR-655 as my main router and that you want to assign only he N. I want to connect my WRT54G for my clients of G. What should I do to the WRT54G, so I do not get with the DIR-655 Router IP address conflicts? Any advice would be greatly appreciated. Thank you.

  Amazing how you 'impossible to find anything' to a question that is probably asked and answered at least twice a day...

  http://homecommunity.Cisco.com/T5/wireless-routers/connecting-two-routers-wired-the-definitive-answe...

• WRT54G - connection works, but problem connecting to some programs

  OK, first I'll explain the game up I have at home.  I use the WRT54G Router, the router is connected to the modem, and I have a desktop computer and a xbox360 both connected by ethernet cables to the router.  I also have a portable computer, which is the computer that has the problem, that connect wirelessly to the router.

  Is OK, the problem ONLY on the laptop.  When I try to go to any kind of big site of videos, such as youtube.com or watch some tv online, video shows only loading a little more, and that they will not play through.  They blow constantly. In addition, just try to load a game like bejeweled, it would probably take about an hour to load up! My computer is only about 2 years old and I had recently tested through company warrantly m and everything on the computer is fine.  He had recently been to the factory settings, so there is not any downloads or whatever it is to slow the computer down, its perfectly clean.

  I tried my computer with a friend, using its settings and internet.  The computer was working fine.  Played videos, responsible games.  Also, I tried the laptop hang until the router also using an ethernet cable and when I did the large working computer then too. This isn't the computer for sure.

  So, if anyone has any recommendations for me, that would be great.  In addition, if you want to know more information made me know...

  I consider myself a little bit more knowledgeable than a beginner, but not a lot... so would you please explain a bit in ordinary English (I know that makes me sound a bit silly, but I'll be honest and need help with this)...

  Please & thank yous.

  As you mentioned that when you connect to your computer directly to the router, you are able to watch the video without any problem, it is only when your computer is wireless to the router.

  Well I think you need to change some settings on your router. When you connect to her Router setup page, click on the Wireless tab and below the first thing you need to do is change the wireless channel: 11-2, 462 GHz and click on save settings... Then you must click the sub-tab under 'Advance Wireless' wireless settings and below change the tag at 50 interval, change the Fragmentation threshold to 2201, change the RTS threshold to 2202 and click on save settings...

  Now on your wireless computer you must disconnect your wireless network and re-connect to your network and check if you are able to play and watch videos without any problem.

  If still the same problem then I think that you need to update the firmware on your router.

  Download the Firmware on your router from the site Web of Linksys. Once you download the firmware on your router, you must follow the instructions below to upgrade the firmware of your router...

  Open a page in Internet Explorer browser on a computer hard wired to the router... In the address bar type - 192.168.1.1... Leave name empty username & password admin lowercase usage...
  Click the 'Administration' tab - then click on the 'Upgrade Firmware' under the tab-here, click on 'Browse' and navigate the .bin firmware file and click on "Upgrade"...
  Wait a few seconds until it shows that "the update is successful," after the upgrade of the firmware, click on "Reboot" and you will be returned to the same page OR it will say 'cannot display the Page.

  Now reset your router:
  Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

• WRT54GS & connectivity ADSL2MUE

  My Modem (Adsl2mue) is set up and works great, I have access to the internet. When I go to connect to my router wireless internet (Wrt54gs) my connection is lost. How can I configure them so they both work together.

  Thanks a lot for the replies

  Gas

  Thanks for the help, that the problem has been resolved. Because they were the two linksys default ip address is the same for each of them. So I had to change the ip address of the router for them set up.

• WRT54GS connection, access to the settings

  
  

  Check what specific model number is your wrt54gs. Look under your router, it's a small lil, but it's there.

  Right-click the wireless network connection / network connection icon and go to status. You should see a gateway IP address... it's the ip address of your router (which is the one that you type on your browser to access. Go to the download pages and download the firmware for the model number and the version of your router. Transfer it to your router so that on a wired computer, reset your router on the back for 30 seconds and reconfigure for your Internet connection. You should be fine after that.

• Computer HP won't sleep when wrt54g connected

  My HP Pavilion m9340f equipped of Vista 64 bit will not enter a standby on its own mode and wakes up unexpectedly when connected to my firmware 4.21.1 wrt54g version 10/17/2005.

  If I disconnect the router and connect your computer directly to the cable modem, the mode "sleep" works very well. Does anyone know how to fix this?

  The problem is an advanced setting in the power management that I used. The default value for the balance and power savings plan is to 'prevent the idling to sleep' when sharing media and I had allowed media sharing on my pc.

  I went to Control Panel > power options > change plan settings > change advanced power settings > appliance settings > what media sharing - and select allow the computer to sleep

  Can I restore default settings when I'm actually share media

• WRT54G connection dropouts

  Hi, I gave connection of the router on a specific scnerio. Hope you guys can help me with a solution.

  Here's the scenario. I have 2 laptops (one is XP, the other is Vista). Whenever I start the laptop Vista, it automatically connects to the WRT54G Router. But at the same time, the connection is getting abandoned in XP laptop and it automatically logs in a few seconds.

  Here is a my router config.

  DHCP server: enabled

  Firmware Version: v1.00.9, may. 12, 2006

  Connection type: Automatic Configuration - DHCP

  UPnP: enable

  Wireless security: WEP

  Thank you

  The Firmware on your router is very old... Update the Firmware on your router...

• Satellite C660 - 1440 Wireless connection interruption on battery

  My satellite seems to suffer from an unstable WiFi connection. It seems to be worse when operating on battery. I read a few comments in the FAQ, indicating that it might be an old driver or my settings for energy savings.

  I installed a newer driver and also tried to change the energy settings on my adapter (not allowing to close), but without satisfying the result. Other options I could try. I find it rather annoying, especially because my I - pod works great on WiFi...

  Thank you!

  And Satellite you need exactly?
  Are you using the original pre-installed OS that you got with your laptop (factory settings)?

• WRT54GS connection problem

  Disconnected last night and everything was fine...  Could not connect to the Internet today...  If I bypass the router, I can connect via my cable modem.

  When going through the router, I get an IP address, an address of a default gateway and DNS1 and address DNS1.  I can't ping the default gateway, DNS1 and DNS2.  The default gateway is a different address when I bypass the router.  When I bypassed the router, I can ping the two default gateway addresses.

  Any ideas?

  Who is your Internet service provider...?

  Do you get the problem on the computer by cable or wireless computer...?

  If you found the problem on the wireless computer, try to disconnect and reconnect the network wireless on the computer. Now, check the ip address and try to make a ping to the gateway & DNS.

  If you have found the issue with the connected computer, then try to reset the router for 30 seconds, power cycle the router and then try to ping the gateway.

• WRT54G connection to an existing network.

  When my daughter goes to the colege this fall, his dorm room has an ethernet port.  In order to share academic network with her roommate, I want to bring my old router and plug.  I have to do something special in the configuration of routers to make it work?  The University Web site has only instructions for switches/hubs.

  You did all that just to have wireless. the way I've done it before is simply connect the LAN ports to the Ethernet connection of the University which is bypassing the DHCP on the router. The only thing you have to install is the wireless and I did so I know it works.

• WRT54GS connected but can't find internet

  Hi I have a wag200g modem witch I connet via cable with a wrt54gs and I connet my laptop wireless with wrt54gs. I have tested several parameter but the internet cannot be found. Is there a framework are what I should do?

  Then, you try to WRT54G cascading on the WAG200G router... Check out this link for both the router cascaded together.

• Push the connection interrupted by device - using eclipse of the bb Simulator

  Using BlackBerry plugin for Eclipse

  For OS 6

  After taking two weeks to try and correct an error "not close until you have finished" simple with SQLite, I now have a bit of a configuration issue with the Eclipse software.

  When I push a message to the Simulator, I get the following error.

  <2012-04-18 15:39:15.471 EDT>:[378]:::http://172.17.111.35:[email protected]&priority=2&besurl=192.168.1... pushId = -62be8811:136c6f71d73:-7ff576188, destination = [email protected], result code = 400 net.rim.protocol.iplayer.push.b: Push connection aborted by device>
  

  According to the knowledge base, a 400 error is 'invalid Push to the format.

  Mobile data service 3.7 and earlier versions: the email address or the personal identification number (PIN) used in the Push was not recognized as a user of BlackBerry Enterprise Server enabled for Mobile Data Service. »

  I'm sure it's something with the configuration in the rim.property file.  Something probably must be on or off, I can't understand.

  [MonitorAgent]
  MonitorAgent.listen.port=8070
  
  [WebServer]
  WebServer.Tomcat.transcoding= false
  WebServer.listen.host=localhost
  WebServer.listen.port=8080
  WebServer.listen.sslport=8443
  WebServer.servlet.monitor.port=8070
  WebServer.servlet.monitor.host=localhost
  WebServer.servlet.push.port=81
  WebServer.servlet.push.host=localhost
  WebServer.servlet.push.ssl=false
  
  [SRP]
  SRP.UID= please get one
  SRP.AuthenticationString= Please get one
  SRP.InetAddress= Please get one
  SRP.Port=3101
  SRP.logging=true
  
  [IPPP]
  IPPP.push.listen.tcp.port=81
  IPPP.connection.MaxNumberOfKBytesToSend=128
  IPPP.queue.flowcontrol.window.size=-1
  IPPP.queue.flowcontrol.timeout=600000
  IPPP.logging=true
  
  [UDP]
  UDP.receive.port=19781
  UDP.send.default=19780
  UDP.init=initialization_packet
  UDP.logging=true
  
  [HTTP HANDLER]
  application.handler.http.logging = true
  application.handler.http.CookieSupport = true
  application.handler.http.AuthenticationSupport = true
  application.handler.http.AuthenticationTimeout = 3600000
  application.handler.http.device.connection.timeout = 140000
  application.handler.http.server.connection.timeout = 150000
  application.handler.http.device.credentialTimeout = 60000
  application.handler.http.authentication.mechName2oid = Negotiate=1.2.840.113554.1.2.2, NTLM=1.3.6.1.4.1.311.2.2.10, Basic=1.3.6.1.4.1.88888.1.2
  
  [Security]
  net.rim.security.auth.DefaultDomain = rim.net
  
  [HTTPS HANDLER]
  application.handler.https.allowUntrustedServer = false
  application.handler.https.logging = true
  
  [TLS HANDLER]
  application.handler.tls.allowUntrustedServer = false
  application.handler.tls.logging = true
  
  [OCSP HANDLER]
  application.handler.ocsp.StatusProviders = net.rim.protocol.iplayer.connection.handler.device.ocsp.OCSPProvider
  application.handler.StatusProviders.OCSP.PrimaryResponderRank   = Default
  application.handler.StatusProviders.OCSP.Responder.Default      = http://dhobbs-wnt.rim.net/ocsp
  application.handler.StatusProviders.OCSP.UseDeviceResponders    = yes
  application.handler.StatusProviders.OCSP.UseCertResponders      = yes
  application.handler.ocsp.DebugLogging = no
  
  [LDAP HANDLER]
  application.handler.ldap.DEFAULT_SERVER = dhobbs-wnt
  application.handler.ldap.DEFAULT_PORT   = 389
  application.handler.ldap.DEFAULT_QUERY  = ou=people, o=rim.net
  application.handler.ldap.DEFAULT_LIMIT  = 20
  application.handler.ldap.COMPRESSION    = true
  application.handler.ldap.logging        = false
  
  [Database]
  Database.shouldConnect=false
  BESName=DAISY1
  Database.Driver=sun.jdbc.odbc.JdbcOdbcDriver
  Database.URL=jdbc:odbc:BESMgmt
  Database.DBCycleTimer=5
  
  [ACL]
  ACL.Authorization.Datastore=net.rim.shared.service.authorization.JDBCAuthorizationDatastore
  ACL.Enabled=false
  
  [ESS]
  ESS.helpfile    = help/Using_the_Email_Server_Simulator.html
  ESS.launcher    = bin/launcher.exe
  
  [Email]
  Email.deviceId      =2100000A
  Email.pop3Server    =pop3.server
  Email.smtpServer    =smtp.server
  Email.personal      =Dean Logan
  Email.address       [email protected]
  Email.smtpPort      =25
  Email.pop3Port      =110
  

  Any suggestions?

  Figured it out.

  When you set the port of the unit, I had the wrong port

  _notify = (StreamConnectionNotifier) Connector.open (appAttributes.devicePort + appAttributes.deviceSide);

  My company uses a Test port and a port of Prod, so that we can have 2 versions of the application on the device at the same time.  Then, chaning the listening port of 1315 to 1313 authorized service push push to the appropriate port and the app was able to read the data.

• Temporary internet connection interruption and error msg

  I am trying to download some PDF forms from a Web site, and whenever I click on the appropriate button to open the form page, the current page

  Gets closed their doors and the internet connection gets temporarily broken causing me to have to re - open up a new window.

  I have this experience also with trying to access government sites as well, but only occasionally, not all the time.

  My question is this:

  Do I have to download some sort of update to the software to allow me to download the necessary forms.

  And if so, which? and can you please provide me the link?

  Thank you.

  Hello
  Please follow the instructions below:

  When you install Acrobat or Adobe Reader on a system that includes a browser, you automatically configure the browser to open PDF files in the browser window. Acrobat and Adobe Reader install the ActiveX plugin files allow you to use Internet Explorer or AOL to open PDF files. If an application is installed, but do not open the PDF files in the browser window, then work through the following steps to configure the browser:

  Acrobat may not work correctly if the system does not meet the following requirements:

  • Intel Pentium III processor or equivalent
  • Microsoft Windows 2000 with Service Pack 4, Windows XP Professional, home edition or Edition Tablet PC with Service Pack 2
  • Microsoft Internet Explorer 6.0
  • 256 MB RAM (512 MB recommended)
  • 860 MB of available disk space; cache for optional installation files (recommended) requires 460 MB of additional free disk space.
  • screen resolution 1 024 x 768

  To open PDF files in a browser window, the ActiveX folder should contain the following files: AcroPDF.dll, AcroIEHelper.dll and pdfshell.dll.

  ActiveX controls must be in: program files Files\Adobe\Acrobat\ActiveX

  If one of these files is missing, then repair Acrobat or Adobe Reader by choosing Help > repair Acrobat Installation or reinstall the application.

  Make sure that you use a version of your web browser, Acrobat and Adobe Reader supports, such as Internet Explorer 6. Supported for Adobe Acrobat 8, Adobe Reader 8 browsers are Internet Explorer 6.0, 6.0 SP1, Internet Explorer 7.0, Firefox 1.5 or later, Mozilla 1.7 and AOL 9.

  To make sure that the Windows registry provides the information that your web browser should display PDF files, restart Windows. If the Windows registry is not updated after the installation of Acrobat, then the web browser can not find the references it needs to access the PDF files on the web.

  If you have an older version of Acrobat or Adobe Reader is installed on the system, and then use the Add / Remove programs in Windows to remove it.

  If you use Acrobat, and then repair or replace the damaged or missing files by using the repair feature the Installation of Acrobat or the dialog box add or remove programs.

  To repair Acrobat:

  1. Choose Start > Control Panel.
  2. Double-click Add or remove programs.
  3. Select Acrobat and then click on edit.
  4. Follow the on-screen instructions to repair the Acrobat.

  7 reinstall Acrobat or Adobe Reader.

  To ensure that the correct information of the plug-in is added to the Windows registry, reinstall Acrobat or Adobe Reader.

  If you want the browser to open PDFs in a separate Acrobat window, then configure the browser to use Acrobat or Adobe Reader as a helper application. Then, when you select a PDF file in Internet Explorer or AOL, the browser opens the PDF file in an Acrobat window instead of the browser window.

  To configure the browser to use Acrobat or Adobe Reader to open PDF files:

  1. Close your web browser.
  2. Start Acrobat or Adobe Reader.
  3. Choose Edition > Preferences.
  4. Select Internet from the list on the left.
  5. Deselect Display PDF in browser, and then click OK.
  6. Restart Internet Explorer or AOL.

  Note: The next time you select a link to a file PDF, the browser may ask you to open or save the file. If you choose to open the file, then the browser opens the file in the support application that you specified. If you choose to save the file, the browser downloads the file to the hard drive.