WRT54G loses connection and will not let me connect again
WIFI at home was great for 2 years, then every sudden in the last 2 weeks I lose my signal on my laptop and iPhone. Then, I can not find the signal, or if the device detects the signal it wont let me connect. He hears no even except my wep key, I get a message saying that I can't connect to the network. Usually, if I unplug my router and the modem I can connect and wifi takes about 24 hours or so I lost. Any help?
Since you have already updated the firmware on your router, you reset your router and re-configured all the settings on your router? If this isn't the case, then press in and hold the reset for 30 seconds button... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...
If your Internet Service is cable follow this link
If your Internet Service is DSL follow this link
When you re - configure all your router settings, you must change some settings under part wireless router...
Set the channel on your router 11-2, 462 GHz Wireless and that the broadcast of the SSID should be activate...
Then click the sub-tab under Wireless 'Advance Wireless Settings' and change the tag to 75 interval... Change the Fragmentation threshold to 2304 change the RTS threshold to 2307... Click 'save settings '...
Now let's see if you can locate your wireless network and try to connect...
Tags: Linksys Routers
I had this problem before on sites Web of VA. How Firefox can not trust a site from the U.S. Government? It indicates that the connection is not approved and will not let me continue. How can I make Firefox let me continue?
This page opens another page in a frame.
In such a case, you cannot make an exception.
This server does not send a certificate chain that ends with a built-in root certificate.
- http://www.Networking4all.com/en/support/tools/site+check/report/?FQDN=vabenefits.VBA.Va.gov & Protocol = https
You can open this page in a tab to make it possible to create an exception if you really need access to the site.
Note that storing a permanent exception should not be.
Open the chrome URI by pasting or typing this URI in the address bar to open the window "Add the Security Exception" and to check the certificate:
In the field location type and paste the URL of the Web site
- retrieve the certificate via the button 'Get certificate '.
- inspect the certificate via the "view..." button. »
Wireless network is displayed with a cross and will not let me connect saying the settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again?
hardware devicemy wireless network is displayed with a cross and will not let me connect saying settings for this network do not match the requirements of the networs and it is a hidden network how to make it visible again :(
What operating system installed on the computer?
Note: Look for errors in the network card device manager.
Method 1: Follow the article mentioned below, if you are using Windows 7 operating system.
Using the troubleshooter from network in Windows 7
He looks at the IP address and other parameters are not set correctly, I suggest you contact your Internet service provider or provider router wireless to help on this.
For more information, follow the below mentioned article:
Set up a wireless router:
Follow the below mentioned articles and see if they help you:
Set up a wireless network:
Wi - Fi and in Windows network connection issues:
Wireless network card: frequently asked questions:
Try to connect to my computer as the administrator, but after I put my login in it goes to check on the page and will not let me connect. The regular connection for the computer works fine. Any ideas?
Try a system restore to a Date before the problem began:
Do Safe Mode system restore, if it is impossible to do in Normal Mode.
Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.
Try a restore of the system once, to choose a Restore Point prior to your problem...
Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.
It is the instance of Vista installation.
Adjust settings, manage user accounts.
Try the Forum above to repost, if necessary.
See you soon.
Mick Murphy - Microsoft partner
This has just begun. When I close firefox it tells me that I am closing multiple tabs. and will not let me save them. the only option is to cancel or OK. When I say OK and restart Firefox all my tabs go :-( This happens every time now. I know how to recover my old tabs but whenever I close Firefox it always warns me that I'm closing multiple tabs.
Tanks for help getting Firefox working properly again
Do not use 'Clear history of Firefox closing' to clear the 'browsing history '.
- Tools > Options > Privacy: history: [X] clear history of Firefox closing > settings
Using the "Show my windows and tabs from last time" is a more reliable way to restore the session data.
- Tools > Options > general > startup: "When Firefox starts": "show my windows and tabs from last time '.
I'm trying to import my IE Favorites and have read the instructions, but the import button in the file in gray and will not let me import. Any ideas?
Try using the import option in the Bookmark Manager (also known as the name of the library)
- In Firefox, select the bookmarks menu, then "organize bookmarks" open library
- In the library, select "Import and backup" then "Import HTML.
- You should get I hope that the ability to import from Internet Explorer.
help I am trying system restore and it says I have no restore points and will not let me create restore points
* original title - find search indexing index reindex re-indexing research research research service troubleshooting troubleshooting *.
1. what exactly happens when you try to create a system restore point?
2. you receive an error message when you create system restore point?
3. what operating system is installed on the computer?
In the event that you use the Windows 7 operating system you can follow the steps below and check if the problem persists.
Locate the service associated with the restoration of the system or Volume Shadow Copy Service is started after the computer is restarted. This service can be stopped by some viruses as well, so you can try to run a scan of your computer.
To check the service
(a) click Start
(b) in the start search box type Services
(c) click on - RUN as ADMINISTRATOR
Check if the below mentioned services has mentioned State and type start.
Shadow copy volume started Automatic\Manual
Also check the dependency services that are required for the System Restore Service run.
To verify that double-click the service, and click the Dependencies tab.
This service must be started before the restore point is created automatically or manually.
Try disabling the firewall and windows temporarily on the computer security software and then try to create a system restore point and check if that helps.
Follow the articles given below to change the settings for the firewall and security software settings
Understanding Windows Firewall settings
Firewall: Frequently asked questions
Disable the anti-virus software
If you are able to perform the system restore after you disable the security software then you may have to contact the software publisher for the security software by disabling the firewall and security software is a potential threat to the security of the system.
Why can't I send an email from the Explorer, it goes to outlook express and will not let me send e-mail
Hotmail questions need to be asked here: www.windowslivehelp.com
This forum deals only with Windows.
recently, when I turn on my trusty 2410xi all-in-One, it of a mechanical blocker and will not let me perform all tasks. I tried to disconnect the supply of the data lines, nothing helps. Looks like the print head may be stuck? I remember having the same problem a long time ago but don't remember what could be the solution to the problem.
There are a few things that you, and not when this happens. Most of the time it's a very small piece of paper holding things to the top, or the printer just need a reset to zero more deep. The document following the link will take you through all the things you can try. If this does not work, you will need to replace the printer. Let me know what happens.
I just installed Windows 7 Professional 64 bit on a new hard drive on my Dell Studio 540. The PC has a graphics card ATI Radeon HD 3450 and has a Samsung 226bw 22 "monitor on the digital output. This works very well, and has the resolution of 1650 x 4050. When I am running Vista (on the previous hard drive), I got a monitor flat 14 "old on the other out, and it worked fine (although at a lower resolution).
I added a monitor AOC F22s + on the other output, expecting to be able to put this to the recommended 1920 x 1080 resolution. Unfortunately, Windows has developed the driver for this monitor "Generic non - PnP" and will not let me set the correct resolution. To the maximum it will allow is 1600 x 1200, (as well as all other resolutions it allows) do not use the monitor at maximum capacity, which is the ratio of evil anyway, so the display seems tense.
I run Windows Update, so have the latest drivers. I tried to install the other drivers, but nothing helped.
I tried to unplug the Samsung monitor and restart the PC, so that the AOC, one was the only monitor it and he always had as 'Generic non - PnP' with the wrong resolution.
Someone at - it ideas? I'm at my wits end. AOC support did not understand and could only suggest that the monitor was faulty, but the place where I bought it insist that it works very well and so no Exchange or get a refund (no restocking fee, which is a RIP-OFF).
I really want to use both screens and would appreciate greatly any help that anyone can give. I hope I gave enough information. If I didn't, please let me know.
Thanks in advance,
It turned out that my VGA cable was wrong and that it was not send the right signal to the computer. The screen worked fine with a VGA monitor, but the PC has not said that the new monitor is a PnP I tried a different cable and it worked fine.
Thanks again to all who have suggested things.
Hello, I have a new Mac, I need help to install adobe photoshop c6 I need to install and pay fees I want. but I've been trying and get no days... I had the version of 30 days and will not let me buy him. I NEED FOR MY WORK PLEASE
Hello, I have a new mac, I need help in installing adobe photoshop cs6, I need to install and to pay the tax. But I've been trying and don't get days, I got 30 days version and will not let me buy it. I need it to work. Please
Hi the isac,
You can download Photoshop CS6 from this link: download Creative Suite 6 applications
You can buy the product from this link: Creative Suite 6
Does anyone know the phone for Customer Service? Im trying to install an app and will not let me
There is no support for this phone.
you could get help if you could explain or you can try to contact support Adobe by clicking here and, when available, click on "still need help," https://helpx.adobe.com/contact.html
Why the application manager said that muse is updated, when it isn't? And will not let me update?
I have the latest version of OS X I opened Muse and he tells me that I have to update. I have check and that's only still v1.1, 960 to build.
There is a promblem I don't know?
Sorry for the confusion and frustration.
Because the Muse is an Air application, there are some limitations in the way that we interact with the Application Manager that can cause these types of States in conflict. We have plans that will address this, but unfortunately, it of a complicated situation and will take time.
I'm working on a document that will address all the various installation questions such as this one and post it on the forum and elsewhere when its done. I apologize that this has not happened before and several people were affected than expected.
See you soon,.
I did a xp pro login password, which was 12 letters long but the connection only takes 11 and won't let me help please
* original title - administrator password *.
Only 11 characters appear on the screen of Windows XP connection at a time, but if the user holds just type the characters will continue to be entered. Please, continue to type the complete password and verify if you are able to connect.
I tested just a password 21 characters who allowed me to log in and out without a problem.
In order to remove online a large number of files in a folder (a folder IMAP?), I deleted the folder and then created a new folder with the same name. The next time I open Thunderbird, all my online except sent and trash folders disappeared, and I could not re - create files that have been deleted. I can't access the files stored in these folders or move files in folders bearing the names of deleted files. I can create files with names not used before. But I can't create a new folder of Junk to hold files that Thunderbird regularly sends to junk. I do not receive e-mail in the process. Local folders are not affected hereby. What can I do? I have Thunderbird 24.5.0. Thanks for any help.
Go to file / subscription and see if you just without subscription to records.
Check folders and make sure EVERYTHING is checked.
Learn how to use several methods of selection and do not delete the records that you want to keep.
control + a = select all
Click heading 1, move upwards or downwards several items and maintain the SHIFT key while clicking the point 2 = selects items 1 and 2, and between the two
Hold down the CTRL key while clicking random objects = selects any element clicked on
Hold down the CTRL key while clicking on a selected item = deselect this item
Original title: OUTLOOK EXPRESS 6 WINDOWS XP
There out wrong and won't let me delete the email. He still receives new e-mail.
no problem viewing or respond.
Anyone know an easy solution?
the error code:
An unknown error has occurred. Account: name, Protocol: POP3, Port: 110, secure (SSL): no, error number: 0x800C0133
Do as I have indicated above, but instead of moving most of the messages in your Inbox, all move them and delete the Inbox.dbx file as well.
If you move all messages from the Inbox for a reason, do the above and then come back and move messages in the Inbox and then delete the Inbox.dbx with OE closed box.
Maybe you are looking for
Hello, I'm in the United States, and one people of Spain want to send me a gift of $ 20, 1 - can it do? 2 and if they do, how can I get? Note: I identifying apple US and I can connect to itunes, but I don't have my password by email! I lost it and I
FN key does not work. .. help me please
I've seen a few posts on here recently, declaring that members have a hard time getting in touch with HP support. Well, I want to address this issue so that members of the community can have this information. If you live in the United States or Canad
Cannot find instructions on adding additional memory in the documentation, even if it does not indicate that there are two memory slots.
I have a Datamax Allegoro printer that uses a USB series converter. The poster converter as installed correctly (in devices and Device Manager) and received COM3. When I go to change the player of the printer to use the COM3 port, it is not in the li