WRT54GS v7.2 difficulties to install

I just bought a v.7.2 WRT54GS recently to get my PS3 and PSP online. I have two computers connected to the internet through a Linksys network hub and a model TM502G modem from Arris Road Runner cable. I ran the CD-ROM supplied with my new wireless router and carried out step by step instructions. The first time I ran it, it captures that I was using the network hub, so I followed the instructions better I could completely out of the hub and all connect through the router. I got the error telling me that the new router or the gateway could not be found, and then I noticed that he was looking for the router as my Local network connection status screen says "invalid IP address". Given that it did not work, I tried to reset my computer and the router and the others, but to no avail. I watched a few messages on the forums of troubleshooting and tried the method to go to http://192.168.1.1/ to change my LAN 192.168.2.1 address to see if this can help, but it was also a failure. So, I tried the firmware downgrade to a version of work confirmed a sticky to make this work with LELA, but still nothing. I ran the Setup program on the CD several times, with the connected router, the router, with nothing else than my modem, and it doesn't seem to work. He finally detected that I had a router, but it is unclear what the wireless. I tried to access the internet via my PSP and I can find a signal from 100% of it, but I can't go on the internet with it (a little a last hope). Y at - it something I am doing wrong? I'm running on Windows XP Edition family and the firmware I am running on the wireless router is currently 7.50.2. Can someone possibly help me, please? I apologize for the long post, but I have tried to provide as much information as I could. I'm pretty computer savvy, but this left mouth gaping me without end. thanks in advance for any help and here's hoping I am not missing something completely obvious.

I finally solve it by myself, so I'll post what I did to make it work in case someone else has this problem as well. The CD-ROM supplied with the router was completely useless to me and still does not detect that I have everything set up. So if you get errors in the program, plug in the router to your computer with the blue wire, the internet is not required. Set up your browser and type http://192.168.1.1/ in the address bar and a window will appear asking user name and password (if this does not work, a reboot may be necessary). Everything you type is admin as password. Under Configuration of him-> the basic configuration (the default page it will take you to), click on the box which says "Automatic Configuration - DHCP" and select "Static IP". It will bring up a few extra boxes, the IP address of your modem and other I think (I could be wrong, it was similar to mine). The only thing you need to fill out is the DNS, I had already written down to configure my PS3, you may need to trace and find yours. Other than that, although I do believe that it is necessary, I changed the "local IP address" 192.168.2.1 as a precaution (don't forget that if you change the innate IP of the router, the URL address, you must type in the browser to access the configuration page will change with him). I saved the changes and plugged my cable ethernet, and surprisingly enough, my internet as well as the wireless didn't work as he had before. No problems yet, but with just as much trouble I've lived with this thing, I wouldn't be surprised. Good luck everyone and I am happy to help someone who has this problem if needed.

Tags: Linksys Routers

Similar Questions

  • Why is it so difficult to install something on a drive rather than on your C: drive.

    Why is it so difficult to install something on a drive rather than on your C: drive.

    [moderate]

    Change the installation for Applications location - (some content should be on the main drive).

    With the application of CC open, select the gear icon in the upper right, and then choose Preferences.  In the preferences of the screen select creative cloud and then look for the drop-down list installation location

  • Having difficulties to install

    Having difficulties to install

    Hi Rico,

    Please specify the error message and the product.

    What operating system do you use?

    Start with the help below document:

    Download cloud creative to troubleshoot and install questions

    Kind regards

    Sheena

  • A possible solution for people with difficulties to install Flash

    I've read through old discussions to try to refresh my memory on how to install Flash for Firefox. I seem to have the same problems in several threads closed - Flash claims to install, but Firefox still happily using the old version. None of the support helped him, but I don't remember how I fixed it before - the Flash Installer puts files in the right place and you must copy them manually to the Firefox Plugins directory. Until the files are in the right place, useful to use on suggestion: addons will not work. Now, if I could only remember how I figured out where Flash updates its files...

    He has got to work! After installing Flash, I had to manually copy ShockwaveFlash.class, NPSWF32.dll, FlashUtil11f_Plugin.exe and C:\Windows\SysWOW64\Macromed\Flash flashplayer.xpt to the Plugins of Firefox directory. Your file names can be a bit different, of course, if you use a different version or a BONE.

    To further complicate things, Flash seems to have dropped support for older versions of Firefox. Install the last Flash in this way causes my browser (Firefox 9) crash when you try to play Flash. Adobe offers no help on what version of Flash is going with what version of Firefox, just to watch the release dates and to make a reasonable estimate. Decommissioning of a published Flash version shortly after Firefox 9 fixed the problem completely.

  • Having difficulties to install El Capitan on my MacBook Pro

    I can't get to El Capitan to install on my MacBook Pro 2012. I tried to remove and re - download several times, tried both Safe Mode. All I get is the following:

    with the Rainbow wheel for 20 seconds, and then nothing happens. I was not able to find anything online to help. Does anyone have a suggestion?

    Here's a tip to user you can follow: basic steps for the OS X upgrade.

  • Conquor first decade and command. Difficult to install

    I have windows vista and I can't install C & C first decade.

    Enter CD - key is successful but when InstallShield reaches the installation process it stops, if I leave my system unatended and back, after 5 minutes of fighting, I get the following error:

    Feature: Command and Conquor (including the add-on pack)
    Component: CnC
    File: D:\Data2.cab
    Error: The request cannot be performed because of an i/o device error

    This error States of the internet that I maybe need to change the way the camera bed programs from DMA to PIO. How can I do this? (remember I am on Vista).
    --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
    Y at - it another way to fix this error?

    Bravo!.

    Hello 70f9,.

    Thank you for visiting the website of Microsoft Windows Vista Community.

    In this article he explains how to change your DMA setting.  You can try these steps.

    Let us know if these steps solve your problem.  I hope the information is useful.

    Kind regards

    Anthony
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Difficult to install a program, I get a setup.exe not one application 32 valid win pop up when I try to install a serif

    I am trying to install a Serif program to create web pages. I get the pop mentioned above to the top. All patches for me. I have a Dell Vostro 1400 laptop with xp on it. I downloaded driver manager thinking it could solve the problem. I think it may just be a domestic framework, I need to adjust, all suggestions will be appreciated. Thank you.

    Hello
     
    Do you get this error message during the installation of the application of Serif only?
     
    How you try to install the application? It's from a disc or downloaded file?
     
    Method 1:
    Empty the Temp folder
    To empty the Temp folder and the Temporary Internet Files folder, use the disk cleanup tool. To do this, follow the steps for the operating system you are using.
    Click Start, point to programs, point to Accessories, point to system tools and then click on disk cleanup.
    C: click or click the drive where Windows XP is installed, and then click OK.
    Click to select the temporary files check box.
    Click OK and then click Yes to confirm the deletion.
     
    Method 2:
    Perform a clean boot and try to install the program, check out the link:
     
    How to configure Windows XP to start in a "clean boot" State
     
    Method 3:
    You can see the following article from Serif to solve this problem: http://support.serif.com/KB/a323/troubleshooting-install-fails-with-windows-installer.aspx
     
    If you're still having problems with enforcement Serif, contact Serif technical support at the following link for further assistance:
     
  • Difficult to install windows xp on my hp mini 110-3012 you

    IWAS, try to install windows XP on my hp mini 110-3012 tu.but unfortunatelly cant. so I need help of pizza I Press f9 at startup and file loading but choose what time drive it couldn't find my drive.so I try change the bios sata setting, but I could find the system sata in bios Setup. So what is the best method I do.i tried nlite but stil not work.somewan please help.

    Hello:

    Please read this link below, and you will need to integrate the DCIS Intel NM10 controller.

    All the info/drivers you need is there.

    http://h30434.www3.HP.com/T5/notebook-operating-systems-and/SATA-drivers-for-XP-solution-on-0x0000007B-BSOD/TD-p/114120

    Paul

  • Difficulties to install automated help desk

    Original title: install the service of automated troubleshooting

    Hello. I am trying to install CARPETS to diagnose a problem with my dvd - rom drive. It will not install and gives the error message "automated troubleshooting service will not install at this time."

    Hello
     
    How Microsoft Automated Troubleshooting Services (MATS) you are trying to install?
     
    I suggest that you put your computer in a clean boot State, and then try to install carpet and check if he moved very well. I suspect there is a conflict of third party software and the clean boot helps eliminate conflicts of third party software.
     
    Note : follow step 7 to your computer as usual.
     
    Aziz Nadeem - Microsoft Support

    [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

  • Having difficulties to install from a CD

    I try to install medical dictionary of Stedman for the Health Professions and nursing care of a CD.  The instructions say do not use the automatic menu because I have Vista.  But whenever I go to my computer and click the drive... I get "Windows Explorer is not working".  Then it closes the program and I can't list the files on the CD so I can run the right one.

    Any help would be greatly appreciated.

    http://www.Microsoft.com/Windows/compatibility/Windows-Vista/default.aspx

    Windows Vista Compatibility Center

    First thing to do is to check its Vista compatibility at the link above, and if not to see what patches/solutions are available from its manufacturer...

    http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-compatibility-mode/

    If this is not Vista compatible, read the info on the link above.
    It works for some programs, but not all.

    This applies to software programs, NOT hardware drivers.

    If it's Vista compatible > right-click on the setup.exe > run as admin.

    See you soon.

    Mick Murphy - Microsoft partner

  • Having difficulties to install printer Brother MFC-J470DW.

    I called brother Support and after two hours of trying everything they could think of, the tech told me I should call Microsoft, that the problem was with them.  When I start the installation disc, it goes only so far and then it stops.  Gets to the extent where "connect cable" and turn on your machine.  And then it just sits there doing nothing.  I tried the system recovery and it did not help.  How to get this problem fixed?

    Moved Windows 7 installation, set at level and activate Forum.

    I called brother Support and after two hours of trying everything they could think of, the tech told me I should call Microsoft, that the problem was with them.  When I start the installation disc, it goes only so far and then it stops.  Gets to the extent where "connect cable" and turn on your machine.  And then it just sits there doing nothing.  I tried the system recovery and it did not help.  How to get this problem fixed?

    It sounds like a problem to brother or one you won't easily resolved in a forum like this one and the first tip that you're going to get:

    Restoration of the machine to factory default (probably an OEM, not Microsoft, method) after the backup of your important data and collect your keys/serial installation media and product numbers.  Then install latest drivers from device hardware and all updates from Microsoft including the printer after you have restored to the factory settings (probably an OEM, not Microsoft, method) and then install all the other stuff.

    Why this review here?  If the people who made and take over the device (alone, you declare having questioned) could not fix things - and you gave NO DETAILS on what they had you try - you could lose your time here discussing the same things again without the expertise of those who intimately know their own device, wrote the software you are trying to install and tested on the operating system you try to install it on--or you could start from a State of CLEANLINESS and last KNOWN GOOD configuration and if it fails, then - be able to solve problems with those to the brother or simply return the product as a failure.

    Now - if you really think it sounds like a pain - provide details on what is and was not considered, etc..

    Other suggestions:

    If you use this:
    Full driver & software package
    ... as your starting point (this is for your device), we'll simplify and get the printer installed first.

    Simply download the driver (assuming that Windows 7 64-bit, another bit of information to provide):Printer Scanner Driver & driver for local connections

    ... chill out, go to the folder where you unzipped it so you can find the full path and...

    1. Open devices and printers, click Start , and then, on the start menu, click devices and printers.

    2. Click Add a printer.

    3. In the Add Printer Wizard, click Add a local printer.

    4. Choose a printer port page, make sure you use a button existing port and the recommended printer port are selected and then click Next.

    5. On the installation of the printer driver page, select the model and manufacturer of the printer, and then click Next.

      • Click on disk, and then navigate to the folder where the printer driver (see above).

    6. Perform the steps in the wizard and then click Finish.

    What he did add a printer to your printer list?  Can you print?

    In addition, in all their troubleshooting, they you save the driver Package & complete software and do a right click on it and run as administrator?

  • Difficulties to install Age of Empires III, help please?

    I try to install Age of Empires III on my laptop HP G62 under Windows 7 Home Premium, but it keeps stuck a blob in to C:\Program Files (x 86) \Microsoft Games\Age of Empires III\art\art3.bar

    Does anyone else have this problem? How can I solve this problem? I really don't want to have to buy another copy of the game.
    Thank you
    Tristan

    There should be no problem install AOE3 without using the compatibility settings.
    Worked for me on Win7 64 bit.

    If she remains stuck at the same point is could be a disk failure. You can try to copy the contents of the disc to a folder on your desktop and install from there. If the files do not complete the copy on the desktop of the disc is probably wrong.

    I do not install all the games in the default location - Program Files (x 86), for several reasons.
    I used separate partition or HARD drive, but a new folder in the c: / drive is good enough. Name it what you like. You can install all your games in subfolders within that.

    Do you have other games that are installed with the specifications of the similar system of the same vintage (2005)? It is possible that the game ends to install if it does not recognize the Intel HD integrated graphics card.

  • Having paid account but with difficulties to install more free trial - only on a pc

    Hi guys,.

    I had to uninstall stuff, and then now I can not install more than one trial, despite having to pay a Sub and have it installed and working on another device...

    I tried uninstalling and reinstalling adobe clean is not, so I am at a loss!

    Your subscription to cloud shows correctly on your account page?

    https://www.adobe.com/account.html for subscriptions on your page from Adobe

    If you have more than one email, you will be sure that you use the right Adobe ID?

    .

    If Yes

    Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

    -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

    -http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

    -http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

    -http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

    -ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp

    -http://helpx.adobe.com/creative-cloud/kb/license-this-software.html

    .

    If no

    This is an open forum, Adobe support... you need Adobe personnel to help

    Adobe contact information - http://helpx.adobe.com/contact.html

    Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

    -Select your product and what you need help with

    -Click on the blue box "still need help? Contact us. "

  • Help, please! Add difficulties to install mode on which I just bought

    Try to install this action with the adobe extension manager, I do somethind wrong, I get the following message: "this extension cannot be installed, it requires the version of photoshop to inclusively between 13.0 and 16.99" How can I solve this problem?

    Thank you

    Adobe Exchange

    Please find the answer in the resource above.

  • having difficulties to install on a desktop 2


    I'm having a hard time installing on my 2nd desktop computer. I have my serial number and go to download, etc, but then he won't "run" so I can complete the process. I get downloaded and then click on him and it "thinks" just but does not open.

    Thanks in advance!

    Mindy

    Please contact the Support from Adobe on the Customer Contact

    Hope this will help you.

    Kind regards

    Hervé Khare

Maybe you are looking for

  • How to share a photo slideshow with Mac &amp; PC people

    I developed a slide show on my iMac from Photos. How to share the slideshow with friends, some with Apple devices and some with PC devices?

  • Speed for Wndr4500v2 wifi problem

    Bye to all I'm new and I hope you can help me.I have a connection fttc 100/10.So far, I couldn't test the speed of wifi, cause peripheral material limits.I bought a Samsung s7 and I did test speed.All my devices supports the 802.11n at 2.4 ghz and 5

  • Office blocking my screen.

    How can I get rid of some of my blue office to block my screen? It's 1/3 from the bottom.

  • Can not unlock my laptop Vista C: drive

    Hello I blocked my C drive week last on my laptop using properties > Security tab so that no one could access it in my house. Now I can't unlock it. I can't access anything on the C:\ even aid and support, or if the user accounts. I tried eveyrthing

  • BB - hosts.cfg definition group-compress

    I have a list of locations that is interrupted by the State. I can then compress so that it shows as separate folders under the main tab. What I don't seem to be able to do is when I break it down to individual States the main screen Sho vice Pages g