WRT610N and ddns

Similar Questions

• WRT610N and Motorola SB6120 DOCSIS 3.0 Cable Modem

  I've upgraded to the modem DOCSIS 3.0 in October due to higher bandwidth offerings of Comcast cable.

  Everything was fine until last week when I had recurring loss of Internet connectivity requires me to reboot/cycle my WRT610N and/or modem.

  I updated the firmware of the currently displayed 1.00.03 B15 and reset the router.  This did not help the situation.

  I also tried the suggestions mentioned here, including the Beacon Interval 75, threshold of Frag 2304, threshold RTS 2307, the wide-40 MHz Radio band.  Reset and cycled the router and modem after all this.  I also tried to power off my computer after each reset, all to nothing does not.

  I'm still losing Internet conncectivity several times per hour.  LELA is unable to repair the connection.  So far, the only solution is to reboot the router.

  Do I have a defective router (still under warranty), or is there a problem to interface with DOCSIS 3.0 modems.  Never had this problem with the old Comcast cable modem.

  My WRT610N is version 1 material.  Wireless encryption is WPA - AES, recommended by Beaver in a previous post in August.  Nothing is connected to the USB port on the router.

  Results of 'ipconfig/all' as follows:

  Microsoft Windows XP [Version 5.1.2600]
  Copyright (C) 1985-2001 Microsoft Corp.

  C:\Documents and parametres\joe > ipconfig/all

  Windows IP configuration

  Name of the host...: jb
  Primary Dns suffix...:
  ... Node type: unknown
  Active... IP routing: Yes
  Proxy WINS active...: Yes

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : hsd1.ca.comcast.net.
  ... Description: NVIDIA nForce Networking Controller
  Physical address.... : 00-14-22-xx-xx-xx
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  IP address...: 192.168.1.107
  ... Subnet mask: 255.255.255.0.
  ... Default gateway. : 192.168.1.1.
  DHCP server...: 192.168.1.1.
  DNS servers...: 192.168.1.1.
  Lease obtained...: Thursday, November 19, 2009 19:04:46
  End of the lease...: Friday, November 20, 2009 19:04:46

  I "x-out" the last 6 digits of my MAC address for security reasons.

  I would be very appreicate suggestions.  I strongly suspect that I would like to order a replacement from Linksys via warranty RMA router.

  Thank you for reading this.

  Sincerely,

  Joe

  Received the replacement router on 22-11-09.  WRT610N rebuilt with firmware v 1.00.03 B15.

  Installed with the current LELA software.  Wireless laptop was runing Vista 32-bit, Wired PC on XP Service Pack 3.

  Everything works normally again.  Replacement router dropped not a (wired or wireless) connection since its installation.

  I find that my original router (bought about 3/09) was defective.

  After replacement of the router, I upgraded my OS to Windows 7 (32-bit on laptop wireless, 64-bit Wired desktop).  No problem at all with the router.

  Hope this helps others.

  Joe

• Quality of Service with WRT610N and Vonage

  I try to get the quality of Service, in collaboration with my WRT610N and my Vonage device.  The WRT is connected directly to a cable modem, and the Vonage device is connected to the Ethernet 1 port.  I have configured the MAC address of the Vonage on the QoS tab as 'High' priority (done by selecting the 'voice device' on the drop-down list category).  In addition, I put my Vonage options (on the my account page of the Vonage site) to use the higher throughput (90 kbps, I think).  Any other setting QoS have been made.

  However, the router seems not to be the QoS application at all.  If I do any kind of surfing at all (dragging around on Google maps to load new pages of satellite is a good test), the quality of voice over a call during Vonage is very choppy.  What I have to do something else to make sure that the Vonage device gets highest priority?

  Follow these connection parameter:

  Modem (DSL/Cable)-> VONAGE-> WRT610N

  Your Modem must be connected to your VONAGE and your VONAGE Ethernet, plug it into the Internet Port of you router LINKSYS. You also check the VONAGE internet connection by connecting your PC to your Ethernet VONAGE before connecting the WRT610N router.

• WRT610N and compatible usb drives

  Hello

  Has someone managed to get a stable connection to the external hard drive USB on the WRT610N?

  I would use a hard drive enclosure that turns down the drive with a sleep mode for reasons of noise and energy.

  With the latest firmware (1.00.02 B10) I tried:

  Vantech Nexstar 3i with a Seagate 1 TB - works very well until the player will power mode how the router to start up export drive even if the USB is on and the management page shows the drive always connected

  Western Digital My Book essential 1 TB - the router is not even mount the external hard drive.  I tried everything... FAT32, NTFS... waited, plugged the USB in and out, power cycled the router...

  Any help would be appreciated, because I spent countless hours trying to get something to work.

  OK, I finally have a system of USB storage to work with a hard drive that goes to sleep.

  Looks like there's a previous WRT610N that does not have a version 1 on the stamp on the underside of the router.  This router did not work well with my hard drives.  I'm a worm 1 WRT610N and use mounts (1.00.00 B18) F/W, The Western Digital My Book essential 1 TB factory delivered and everything works fine.  On the USB data rates are approximately 2.4 MB/s via wireless with security AES .n and 5 MB/s via ethernet cable.  Funny is that more recent (1.00.02 B10) firmware will not mount drive Western Digital My Book.  Interesting that in the version notes it says «enhanced recognition of USB external hard drives»  Well, at least I'm happy with something that works; 4 weeks and many hours.  Unfortunately, Linksys does no more than F/W on their website, so I'll never upgrade in case I lose the ability to connect to my new hard drive.

• WRT610N and WGA600N game help?

  Hey everyone I need help to find the best settings for wrt610n for games and it goes the same for the wga600n. whenever I play a game the connection falls for about 1 minute then I can play again. as he always says something about the strict firewall whenever I play war gear please help. Thank you

  I figured out problem that the triclk is if you play on a console or anything that allows you to take off the firewall, you need to do DMZ is enter the ip address for what you play and BOOM the connection is good. I turned on the 5gz return string and it works perfectly since there is no firewall to slow the connection on my xbox 360

• EA3500 and DDNS

  I'm trying to set up the DVR digital surveillance.

  By education I select dwddns.net, set port 8245 DDNS server and the name of the DVR. I click on check (which I guess see if the name is availble) then I'm supposed to enter dvrname.dwddns.netortnumber in the Internet browser and I'm supposed to be able to access the DVR. Is there some setting that needs to be entered into the EA3500?

  Hi Techcoor. Have you checked if these ports are already open? Go to www.ping.eu and go to check port. Make sure that the firmware of the router is up-to-date. I'm not familiar with the DVR. I suggest that you consult your manufacturer in this regard. I'm sure they can give you workarounds.

• WRT610N and IpV6?

  I have the last update of firmware posted the 1.0 model the WRT610N.  Test - ipv6.com is not reassuring, since pure IpV6 sites do not react, but I don't know if it's my router or some other problem.

  The WRT610N will work correctly once IpV4 disappeared, or am I intended to buy another router?  Except if forced, I'm perfectly happy with this one.

  Thank you...

  The WRT610N does not support IPv6.

  But it doesn't matter. IPv4 has not disappeared. And will not disappear. At least for a very long time.

  And as long as you don't need a site that is only accessible via IPv6 it won't matter anyway. And even in this case, Windows supports different IPv6 tunnels that allow your computer to use IPv6 even if your router is not.

• WRT610N and DMA2100

  I just installed a router to my network, WRT610N, v2.0, its largest number, instead of my WRT350N, whech had even developed a fault. The network seems to work correctly, after letting the configuration, etc.

  However, my Media Center Extender, Linksys DMA 2100, must be re-attached with the computer whenever it is re-powered. As this process takes about 20 minutes and then he's looking for the library. The Media Center Extender has worked well with the old router. There is also a router TPLink Tl-SG1005D, gigabyte router, taking the cable between the router and routing it in three of my boxes of home entertainment with the Extender. As I say, worked perfectly before the change.

  I'm now running Windows 7, I've been on beforre Vista.

  I deleted all traces of the Extender to my system and re-installed. No change, must still be reconfigured each time.

  Can someone tell me what to do?

  Philip283

  the link has been wired throughout. Thank you very much, I'll try security coding.

  I think that the problem may be with tha Protection network supplied with the machine (try it for 2 to 4 weeks). There is no intructions on how to disable. I already have a security program installed.

  Philippe

  .

• compatibility issues with WRT610N and WMP300N security mode

  Greetings from the experts out there. I have adsl AM300 + WRT610N pulled upward at home my receiving office on WMP300N wireless broadcasting (only 2.4 GHz wireless signal that I have disabled 5.0 GHz for troubleshooting). Get the best connection with the configuration below (WEP without authentication). I tested with WPA, WPA2, WEP with shared authentication. All these 3 combinations security mode does not allow my office to connect to my WRT610N router, which leads me to assume that there might be a problem with a pilot of the aircraft. The only link that almost succeeded was with WPA2 because I managed to get the LAN connected but not being is not able to connect to internet via AM300 so I have concluded that it is another problem too.

  AM300

  Software version: 1.19.04

  ===================================

  WRT610N-SG
  Firmware version: 1.00.00 B17
  ===================================
  Security mode: WEP
  Encryption: 104 / 128-bit (26hex)
  TX key: 1
  Authentication type: Auto

  WMP300N
  Driver version: 4.150.22.0 6/21/2007
  ===================================
  Security type: no authentication (Open)
  Encryption type: WEP
  Key index: 1

  (1) are you able to get a good market condition the Internet connection, using a computer that is connected to the WRT610N?

  (2) are you able to get a good market condition the Internet connection, using a computer which is connected wireless to the WRT610N, when no encryption is used?

  If the answer 1 and 2 is Yes, then:

  First of all, give your network a unique SSID. Do not use "linksys". If you use "linksys", you can try to connect the router to your neighbor. Also set 'SSID Broadcast' to 'active '. This will help your computer to find and lock on the signal from your router.

  In addition, in the computer, go to your wireless software and go to 'Favorite networks' (sometimes called 'Profiles'). There are probably a few listed networks. Remove any network called "linksys". Also remove any network that you don't recognize or that you no longer use.  Delete your current network (this will remove all old settings.)  Restart the computer.  Return to "Preferred networks" and re-enter your current info from the network (SSID, encryption (if any) and key (if any)). Select your current network and make your network by default, then set it to auto login. You may need to go to 'settings' to do this, or you may need to right click on your network and select 'Properties' or 'settings '.  Restart the computer.  The computer should automatically connect to your router (this may take up to 2 minutes).  If you're still having problems, temporarily disable your software firewall computer, then try again.

  Note: For WEP, enter 'key WEP 1' (found in the router) in your computer, not the WEP password or passphrase.

  If the above does not solve your problem, download and install the latest driver for your computer's wireless network adapter.

• WRT610N and iTunes home sharing

  The router works fine in all aspects except that some computers on the network lose their iTunes home sharing connection to other PC... in this case the wired PC and see each other and wireless computers can see each other... but all lose the ability to see everyone.

  I solve this in each time by going to the configuration of the router and clicking on 'save settings' on page of the same configuration if I havn't made no changes. A minute or two after the recording of all host actions in iTunes reappear and will stay for a certain period of time.

  Anyone know if it's a question of iTunes or something that I can put it on the router?

  Thanks in advance for your comments.

  B Smith

  Problem solved with frimware update 2.00.00 B05.

• Link WRT610N and storage

  Really wish that I had read about the storage link does not, as being able to access it from Windows. I can see it in the online interface, but not from windows. Anyone have any idea when Linksys will be solving it. PnP my * beep *.

  You must map the drive connected to the router network.

  1. connect to the router interface web and create a share for the storage drive.

  2. create a user with admin rights.

  3. map the drive on your windows computer.

  Start > Search > computer network search > enter the IP address of your router: press ENTER.

  You will find a folder in your player - double-click on it - he would invite for username & password - enter the user information that you created and it will display the content.

  4. now click on tools and select map network drive.

  It is will the drive in my computer.

  Try this and let me know if it works.

• WRT610N and twonky media server PROBLEM

  Hi, I finally had some time to install my network wireless at home, everything works well except the media server, im trying to connect an xbox 360 and ps3, they see in the media server and I can access the problem is that the only file that they see is "trial expired, please visit http://twonkyvision.com.

  I already tried to go and found a topic on it (link ) and it helped me to access the media server settings, I tried the solution posted, but it didn't work; I looked in the options and found that over my registration key number is bright red the following words: "this key is already used by another instance of the server." and here it is a counter with 0 days for the trial.

  Anyone know how I could solve this problem or what it exactly means and how to solve this problem, my router is new, but it has been sitting on my desk almost three months because I don't have the time to install it.

  Any help would be appreciated, thanks.

  OK, I have a major update and a possible solution, I was buggin the twonky people until they gave a new key number who worked and solved my problem, on the other hand, they have told me that, with the next firmware, updated the router doesn't ask for the key more could operate freely, so you can either go to the twonky´s customer service or wait for the next update. good luck to all

• NETGEAR wnr1000-N and WRT610N AP

  Hello

  I have a WRT610N and Netgear WNR1000N just got Comcast, and I want to use WNR1000N as a wired router and use WRT610N as an Wireless Access Point. Is this possible? Thank you

  Thanks for the quick response. Oh it's not good to hear. I don't want to launch a hundres of feet of cable through the walls and the attic. Everything can chance I reverse using Netgear WNR-1000 as a wireless network access (WAP) instead point the WRT610N? Thank you

• Help on the portable computer connection on the desktop and router WRT610N

  I just bought a WRT610N and have loaded in my office which is not wireless and connected to my cable modem and the router on the desktop so that I can get the Wi - Fi of my wireless control internal Laptop Dell Insperion 1501.  My laptop shows my network I have install on the desk top and there are 4 bars green connection excellent, but it does NOT connect to the INTERNET.  How can I fix it?    Please help me sooooooonnnnnnnn.   Thank you very much.

  Try this,

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER...
  Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab

  2.4 GHz wireless settings:

  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect... Make sure your wireless connection is st to obtain the IP address automatically.

• Degradation in speed WRT610N

  IT pro with a new router WRT610N - Firmware Version: 2.00.00 B05

  Connection Internet is a cable modem of 30 MB and I have connections wired two gigabit for the WRT610N and two 100 MB wired connections and multiple wireless devices.  I use WPA-2 on both bands and MAC address filtering.  I have NO problem with the wireless, in fact, that it runs better than I expected.

  HOWEVER, my internet connection the router's wireless AND wired connections is deteriorating in the speed of 25-30 MB up to about 5 MB on a daily basis.  If I just restart the WRT610N, back right connection speed shoots up to 30 MB each time - this leads me to believe that the WRT610N is the culprit here.  I don't have any special settings other than a few forwarded ports to my desktop and I don't see any wandering TCP connection when these speed degradations occur.  Even a restart of the computer has no effect.  Apparently, it is in the router.

  I would like any suggestions you all have in this case - as I can hardly believe that I am the only person with these symptoms.  I have been using Linksys and Cisco equipment for many years and have never had a problem.

  Please, let me repeat - this is NOT a problem with my wireless, so don't suggest things like disable MAC filtering and others - this is specific to the overall speed of connection to internet via the WRT610N Wi-wired connections AND.

  Thanks in advance!

  Brian

  Contempt, people... I found the culprit!

  This stupid "Home Network Defender' is apparently ONE by default.

  Problem solved.