WSN-3202 sensor supply voltage

I want to know the amount of voltage that provides power to the sensor of WSN-3202. In the datasheet, it is written that it provides 12.6V. But if I operate the WSN-3202 battery, then to the maximum node, it can get 6 v battery of four. then, how it may be able to give where driven by battery 6V 12V sensor? Help, please.

I have another question, with regard to my knowledge, the node not send data continuously, when gateway will call it, send it and so it will save battery by making it on after call from bridge - this idea is good? If it so, then when the node is in mode 'sleep' (do not send all data, connection) will give no voltage sensor - it should be? is it? then when the gateway do call, connection, gives power to the sensor. but he will do a delay to give power to the sensor and collect sensor data right? will this affect?

Hello, KJV,.

Must have lost this reply in my email. My apologies that I answer all the time!

The sampling interval is when the wake of nodes of samples, the front-end (IA and DIO) and transmits that data back to the gateway. This is done on the sampling interval, so if your sampling interval is 5 seconds is how many times it happens. The node is in standby the rest of the time. Sampling and sought takes ms.

The time setting power sensor is for you to specify if you want to than the power to allow line. If, for example, if your setting is 250ms for sensor supply and our sampling interval is 5 seconds:

1 start time = 0

2. the sensor works in 4.75 seconds

3 example of front end and transmit data to 5 seconds

4 node falls asleep to ~5.1 seconds

Let me know if this clears things up for you.

Again sorry for the late reply.

Corby

Support Engineer produces WSN R & D

Tags: NI Products

Similar Questions

  • WSN-3212 or NI WSN 3202 when loaded with VI target with

    WSN-3212 or NI WSN 3202 when loaded with a new firmware using option "Add LABView WSN target", cannot re connect with the gateway ethernet OR WSN - 9791. In MAX, the quality of the link state is "lost Signal".

    Basically, I tried to change the sampling in the sample interval ""case structure, then built the VI and deployed on two WSN nodes. " They show the status of the download of the firmware and the LABView also shows the message 'successfully deployed", but then, knots just to start scanning and never connect again.

    Please help in this regard.

    Hello binarystar105,

    When you have downloaded the new firmware, did you follow the steps described in this article?

    How to upgrade the Firmware on my NI WSN gateway?

    http://digital.NI.com/public.nsf/allkb/CF6241F5F849FC7086257909008327C5?OpenDocument

    Also, what version of firmware you currently have?

    What version of the LabVIEW WSN Module work?

    If you look at the properties of the node of your window from the LabVIEW Project Explorer, can set you the tab node sampling interval?

    You may already familiar with this material, but I found the following white paper to be extremely useful when I started working with WSN:

    Getting started with wireless sensor networks of NOR

    http://www.NI.com/white-paper/8890/en/

  • How to make connections on the outputs of the letter of wsn 3202?

    GOOG morning engineers,

    How to make connections on the outputs of the letter of wsn 3202?

    Sorry, I'm very confused by your response.

    You must not something on the power set by program, just connect a power supply to DIO power and mass of DIO.  Then your DIO lines should be able to output values.

    In addition, I think that you may need to configure the output line.  This would be by the project.  I don't remember what it is, but it should be in some menu properties (probably for the specific line of DIO).

  • Write the name of shared variable wsn-3202 the string of the action file name

    I use the output of several nodes Variable shared, assigned to an analog WSN-3202, as input in writing to measurement file Express VI. They are merged before entering write it as file Express VI using merge signals. I write data to a file text (VLM). In the output text file the columns containing data from the analog channels WSN-3202 are titled "Untitled", "Untitled 1", "Untitled 2" and so on. " I want that these titles to be based on the WSN-3202 node name and the channel they represent. How this is done? I've attached the output text file.

    Hello

    There is a VI called to set Dynamic Data attributes where you set your signal name.

    I hope this helps!

  • Problem using the Keithley 6487 pAmmeter with supply voltage.

    I try to use a Kiethley 6487 to bias a photon detector in my lab and I am new to LabVIEW. So far, I've been able to get current the ammeter readings, but I can't increase the supply voltage. The code I came up with so far is able to start communication over distance with the device but returns an error when you use the vi ramp. Here is the error I get:

    1074135024 error has occurred in KE6485 configure Source Ramp.vi

    Possible reasons:

    Driver status: (Hex 0xBFFA0010) invalid value for the parameter or property.

    I removed the piece of code related to the drafting of my main block diagram and changed my global variables to the constants. Any help on this would be highly appreciated.

    Thank you
    Cameron


  • Help me choose a memory supply voltage.

    HP p6-2000ru H0B97EA #ACB

    Hi guys!
    I have a question.
    My system supports the following memory types:

    • PC3 10600 (1333 MHz)
    • PC3 12800 (1600 MHz)
    • PC3 14400 (1866 MHz)

    But not the specific 1.35/1.50/1.55/1.65/1.90V voltage

    Here, we have sold in the region, these pairs of modules (they differ only by the supply - grey voltage: 1.5V Blue: 1.65)
    Who is better suited in my system?

    Now, I have installed a module Hynix HP 4 GB 2Rx8 PC3-10600U-9-11-B1 HMT351U6CFR8C-H9 NOT AA 1201
    I don't know what to buy a game - blue or gray?

    Thanks for the links. The prices are good. (Today Black Friday)

    First store will not send to the Russia.
    * Second store has not sent abroad:

    Newegg.com is not delivered at the international level. We ship to the United States and Puerto Rico and APO/FPO addresses only

    Thank you for your help.

  • 36 wsn-3202

    Hello, dear OR engineers!

    There is a task to build net wsn with 36 x 3202 modules on a COMPACT territory and 9791gtw ~ 70x70meters, is it possible?
    (All documents are read, please visit)

    Problem is that all modules can 'see' radio signal each other in the small territory while it produces interferences and there is no possibility of separate wsn-routers.
    All modules are distributed on a square regular. WSN-9791 is one side of the square on a height of 8 m.

    Someone at-ideas? Or maybe sombody can convince me that such system is incorrect? Plan in attachments.
    Thanks for any help!


  • 2 power supply: voltage increment on one when the current research on the other?

    OK, so I work with 2 power supplies E364X Agilent. I have a unit with a door and drain that I do apply power. With the door I am applying 1.5V & .3a current limit, the drain I do a request 9.5V & 1 has current limit. What I'm trying to do, is to increase the tension of the door while controlling the current Drain and have the increments to stop when the Drain current comes down to .5A +/-50mA. I guess I kind of two questions. I use a state machine, the first iteratino defines the PS for the desired parameters (works fine), the next two iteration is supposed to accelerate the Power Supply Gate Voltate with small increments, check the current reading of power drains to see if it falls in the interval given, otherwise the increase continue, check again and so on... I'm having a problem with the part of increment as well as checking for the current game. I was thinking maybe I need to use a flat sequence or something along that line. Any help would greatly be apprecaited

    For #1 supply, you should just have the voltage itself inside the loop.    It would probably not hurt thanks to additional error checking just in case (you can then give up if there is an error).  The rest can probably not stay outside the loop.

  • I can measure analog USB supply voltage using Labview?

    I'm basically feeding a (nominal) 5V USB power sensor, but the output of full scale depends on the real for a particular measure input voltage - what I want to do is to get labview to measure the voltage at the USB port at the same time it samples the voltage of the output sensor and then that of full scale output for that instant in time can be calculated and thus give a measure more accurate. Is this possible in labview? Thank you very much.

    Haydn Barker

    Makes a lot of sense, actually - probably would see a few mV dropped from the point of measurement of the sensor point... then you work with equations/remedies just to work with an inaccurate level anyway. Okay well I'll write that off as a bad idea then and just stick to the system, because it isn't now - I don't know that it will be enough. Thank you for your answers and help.

  • Unable to set my HP6632B supply voltage of 12 v with the hp66xxbc

    Hello:

    I use the IVI hp66xxbc driver to control a power supply DC HP6632B, and I get an error when I try to set the voltage of 12V.  I can adjust the tension manually on the front panel and using the option "Contact instrument" in the tool "Measure and Automation", but not with the driver of the IVI.  Any help would be greatly appreciated.

    I tried to set the ÖVP at 20, but the pilot didn't like either.  And I could do it manually. This part is not included in the attached report.

    Here is my configuration:

    LabVIEW: 7.1

    hp66xxbc driver: not sure.

    Just run "HP6632B-Init-and-Set - voltage.vi.

    Here is the error I get:

    "Error 1074135024 occurred to hp66xxbc configuration OVP.vi.

    Possible reasons:
    Driver status: (Hex 0xBFFA0010) invalid value for the parameter or property.

    Secondary error: (Hex 0xBFFC0004) parameter 4 out of reach, or an error occurred when setting setting 4.

    "Development: OVP limit"

    Hello Mike,.

    It seems that the problem is possibly due to the deactivation of the query ID in any of your folders.  In many cases the specific driver IVI uses by default the model with the minimum of features and smaller beaches.  Do you have errors if you try to set the ÖVP to 2 volts?  If you still have a problem after activation ID query and try a smaller value of the ÖVP, please post an example with a minimum of code that reproduces the issue and doesn't use the wrapper to live and also include a capture OR the spy of the occurrence of the error.

    See you soon,.

    NathanT

  • Deployment error - NI WSN 3202

    Salvation OR engineers,

    We will continue our conversation. Please see the message erro in the attached file.


  • I can adjust the paper supply voltage

    When I print a project my HP Deskjet 6540 will sometimes spring from 2 pages at a time and then that ruin my numbered pages as I print on both sides of the paper?

    Thank you.

    Hi cleo44,

    I understand that you sometimes have a problem with several pages at once feeding through the printer. I'll try my best to help you solve this problem.

    In this document of Several Pages feeding through the printer are steps may resolve this problem.

    I hope that this helps, please let me know how it goes.

    Thank you

  • power supply for hall sensor

    Hello!!

    I ordered NI DAQ 6008, now my question is what do I need external power for my hall sensor or the hall sensor is powered by data acquisition itself?

    thanq

    In the datasheet, page 4 shows the supply voltage 5V, as 5.6mA power supply

    So yes, you should be able to connect directly.

    + 5V - pin 31--> + Vcc

    GND - pin 32--> GND

    Vout accesses one of the digital input pins.

  • I can acquire a signal of 2 wire vibration or accelerometer sensor with a NEITHER-9208

    Hello

    I have a vibration of 2-wire sensor, this sensor gives me a 4-20mA signal, 4 my = 0 ips or any vibrations present and 20 my shows the beach from the tip of vibration is present, my ips for this sensor range is 0 - 2.0 ips, initially, I had chosen the 9218 OR to set a connection IEPE, but this module have only 2 channels , so the NI 9208 has 16 channels, so my question is, can the NI 9208 acquire this signal without problem?

    The 9208 is the correct unit to use. See the manual (fig3)?  How to connect the two sensor wire (loop). Need for an external power supply for this unit. For the min/max of the supply voltage, see the technical details of your sensor. (24V power is common, but it must meet the requirements of your sensor!)

  • fiber optical sensor su19 110 115 a 126 vs nor usb 6008

    Hi expert... I am looking for idea or help on my project. I try to get the measure of mention nor USB 6008 sensor output. In fact, I'm new with nor peripheral usb n still study n the search on internet or n. forums I found an idea to connect the sensor by aoi, but I can't seem to get a measurement any. Is the sensor can connect directly to the device usb or need some custom wire diagram between them. Thanks in advance

    First of all, it is useful if you name the manufacturer of the sensor. A single part number means nothing to most of us.  You use the sensor fiber-optic Pepperl + Fuchs? Even better is to display the technical/manual plug of the sensor or links to them.

    The data sheet that I found for the sensor to Pepperl + Fuchs is not very well written, in my opinion. It seems that the outputs are impulses with dependent amplitudes of the voltage and the frequency or the timetable set by the mode of operation.

    If it's the device you use, the only way you have any possibility to decode the outputs with the USB-6008 box is to measure with an analog input and then process the data in the software. According to the supply voltage, you will probably need a voltage divider to reduce the output voltage of the sensor to a level compatible with the DAQ hardware.  You also won't be able to use the high speed of the probe because the heart rate exceeds the Nyquist limit. In standard mode, you mighte be OK, but you can use a single channel of the USB-6008 to stay in the Nyquist limit.

    Lynn

Maybe you are looking for

  • having problem reading pdf files

    Hello world! My name is HP slate 7 HD 3403ea. I'm having some trouble reading PDF files. That day, after that I bought my tab, I transferred about 25 PDF files from my handset to this tab. I could open all the files then. But a few hours later, when

  • HP pavilion h8-1230: how to access the bios pls help

    How to access the bios and I got windows 7 but to give birth to windos 10 with the thing free upgrade I got Pls Help

  • Snap away

    UH... My function to grab imaq disappeared, thoughts?

  • HP Pavilion G6-1242ee: Configure switchable graphics button is missing!

    Hello. I went to my device manager and click with the right button on my graphics card to day. The update succeeded without any problem. 2 pilots that I displayed view: AMD Radeon HD 6470 M and Intel HD graphics Family. These are the drivers that I h

  • ERROR 0 X 00000015

    Hello! I have the problem with HP LJ 3052! I directly HP connected to my PC with Win7, all functions except scanning work. When I am trying to scan from win7 in indicates the error code 0 x 00000015, get I try to scan from the printer, it displays "w