Similar Questions

• time (for wsn 9791) in MAX server configuration

  Hello

  I need to set up a time for my gateway WSN9791 server in order to ger readings with timestamp of remote nodes. How can I do?

  I already checked this forum and other sources of information on this issue and has concluded that the time server is configured by using MAX under "Remote Systems > NOR-WSN9791 > System Settings" but I have not found any arrangement for the NTP server there.

  My system configuration is:

  -Windows 7 Professional

  -LabView 2013

  NOR-WSN 2013

  -MAX 5.5.0f0 of worm.

  -a WSN9791 gateway

  -eight knots of WSN3202

  concerning

  Flavio

  Finally, I asked the technicians support of OR who have come to find a solution.

  I report the message that describes the problem.

  ------

  Why can I not set a time for my NOR-WSN-9791 gateway server?

  It is a known problem in NI MAX 5.5 and 5.6 MAX OR. The time server option was not be displayed due to a change in the backend of the system settings page. Workaround to view the setting of the time server was created. The following steps will allow the option of time server OR 5.5 or 5.6 MAX MAX OR

  1. on your development computer, go to C:\Program NIUninstaller Instruments\MAX\UI Providers\DefaultRemoteUixml\ to C:\Program Files (x 86) and 64-bit windows \National Instruments\MAX\UI Providers\DefaultRemoteUixml\ for 32-bit windows.
  2. in the directory C:\Program Files (x 86) of Providers\DefaultRemoteUixml\ \National Instruments\MAX\UI, make a copy of the original mxrmcfg. DDPSystem.def.xml original-mxrmcfg file. DDPSystem.def.xml. this backup the original file to undo the changes.
  3. open in Notepad the file mxrmcfg. DDPSystem.def.xml

  4 replace the contents of the file with the following:

  
  
   
     
     
   
  
  5 restart NI MAX

  After you follow these steps, you will be able to set the time server on the NOR-WSN-9791 via NI MAX.

  ------

• WSN-9791 frequency selection and interference

  WSN-9791 indicates that it can operate on the 2.4 GHz band channels 11-24 (I'm guessing that USA is limited to 11).  How to avoid multiple interference OR WSN, in the same neighborhood?  Is there a way to set or determine the channels that the network is working in?  For example, with the 802.11 standard common internet hubs can fix them to use one of these 11 channels.

  Thank you

  Garrett

  Hey Garret.

  You are right that channels 25 and 26 are outside the range of 802.11, but they cannot be used for the same reason that you can't go to channel 11 for 802.11 here in the United States.

  Also, for the gateways in the same neighborhood, you must assign different channels.  Gateways running on the same channel in the same vicinity will cause problems for both networks.

  The questions keep coming!

  Kevin

• WSN-9791 Firmware

  I'm trying to update the firmware on my WSN-9791. I see the 9791 in Max and OR network browser. I use MAX version 4.7.7f0. The current version of the firmware 9791 is 1.0.1. I have the ni9791fwROM_LV861_LV2009 file. Once I click on the Firmware update, I click Yes and I see: Check The WSN gateway Firmware consistency... After that a few seconds, an error message appears saying: a communication error occurred during the update the WSN. Reboot and try.

  I tried to restart but it does not work.

  Any help is appreciated to muvh.

  Thank you

  Hi wv,.

  It seems that it is a network connection problem. For the most part, the software installs our hardware restarts in installation mode and trying to reconnect to the computer now to begin the installation of the software. At this stage there may be re-problems connecting to the PC. In practice, this problem manifests exactly as you described.

  Here are a few troubleshooting steps:

  -Drop your firewalls

  -disable the antivirus

  -set your camera to have a static IP (see this kb).

  -turn off wireless on your PC

  If your computer has multiple ethernet ports or several cards it can also cause problems like this.

  I would like to know how they

• My gateway crashed, after using my Dell recovery disk, I can't activate my Windows

  I can't activate my windows now. Is there something I can do? Just a note: I bought two of these computers and carry the product numbers.

  Gateway who told me:
  "I regret to inform you that we are unable to provide a service of this system, given the age of the system and because of the unavailability of parts."

  Is there something I can do?

  Original title: my gateway crashed, he even out recovery and I lost my recovery disc. I have a Dell and the recovery disc to install windows xp on it.

  Hello
   
  System which comes preinstalled with the operating system are the unique product key and it is recommended that get you in touch with the manufacturer to get the product key or a recovery disc.
  Note:
  You would need a gateway disk or a System Builder copy/retail copy and use the product key provided with the computer to turn on.
  Explanation of SLP
  Used by equipment manufacturers (OEM), SLP (Locked) preinstallation system uses the information stored in the computer's BIOS to protect each installation from casual copying. No communication by the end customer to Microsoft is necessary. At the start of the system, the operating system compares the computer BIOS to the SLP information. If it matches, no activation is required.

• WSN-9791, management to the 3202 errors

  I have setup a 9791with 3202 and attached to a 250 Ohm resistor to measure a 4-20mA signal to the 3202 AI0. I'm always out of measing the input voltage and I also check the voltage of battery, link quality, external power supply and error messages with the management of simple mistakes. Everything seems to work properly. Now I disconnect to the 3202 and remove the batteries. Surprisingly, the voltage to AI0 remains its value, the battery voltage remains the same, it shows as external is present and the error handling will not display any errors. After 3 minutes MAX will show that the signal was lost. The VI shows that the external power supply has been disconnected. All other values remain the same

  I'm using LabVIEW 2009FDS and I don't have a Pioneer or any additional software. I have updated the firmware of the 9791 and 3202 to the latest revision.

  How can I display in my VI that the signal has been lost? MAX seems to be able to do so, but only after 3 minutes. Why the management of errors never poster no matter what? Why is the quality of the binding the same when the signal is lost?

  Thank you

  Hi wv,.

  I'm sorry that you are not satisfied with the features of the WSN material.

  You need not actually a time accurate system to check if your data is obsolete.  What you need to do is check compared to the timestamp of the last time read you.  In this case, it matters really very little whether the internal clock is 1903 or 2011.  You check just to see if the data was updated to say the past 3 minutes.

  As far as the quality of the connection goes, it's also a common variable and therefore likely to be the same phenomena as the other values of nodes.

  Have a great day,

  Chris V

• Windows Server configured as the gateway crashes with referee interface

  I'm running the Active Directory to Windows 2008 R2 servers multiple infrastructure test lab. One of the functions as a gateway server, configured with routing and remote access. Each time, after a few hours, the network to public internet traffic stops. One way to solve is, is to restart the gateway server. When network stops, same gateway itself cannot connect to the public network, the DNS servers of the ISP ping with the IP addresses is answer. Ipconfig/release and / renew buy do a thing and disabling WAN network interface freezes. After that, try to stop and restart the server will be fallow with blue screen and cold reboot.

  WAN interface uses the pilot VMNET3 and Intel LAN interface 1000 (something like that). VMtools has been installed from the console of the last version of ESXi.

  Familiar with this problem to anyone?

  Try to change the external NETWORK adapter to E1000.

  ---

  MCITP: SA, MCTS Hyper-V, VMware vExpert, VCP 3/4

  http://blog.vadmin.ru

• connect to 9791 WSN gateway on different domain

  RE: gateway WSN-9791

  I want to collect data from a WSN without going through a computer at the location of very distant field.  For 1 beat per minute, we don't need the power and the cost of a RIO, or even a laptop computer in the remote location.

  I want to use a gateway 9791 (with some WSN-3202 devices) in a place of far field, directly connected to the internet via a satellite link.  I want to run a LabVIEW program on a computer at the location of the head office.  I intend to collect remote data locally on a LabVIEW VI without a computer in the remote location.

  Since the 9791 won't be on my same network back to the home office domain, how MAX to find the 9791?

  I've only used the 9791 on a local network, where MAX auto-detection is, well, automatic.

  William Reed

  Double Post.

• remote connection to 9791 WSN gateway

  RE: gateway WSN-9791

  I want to collect data from a WSN without going through a computer at the location of very distant field.  For 1 beat per minute, we don't need the power and the cost of a RIO, or even a laptop computer in the remote location.

  I want to use a gateway 9791 (with some WSN-3202 devices) in a place of far field, directly connected to the internet via a satellite link.  I want to run a LabVIEW program on a computer at the location of the head office.  I intend to collect remote data locally on a LabVIEW VI without a computer in the remote location.

  Since the 9791 won't be on my same network back to the home office domain, how MAX to find the 9791?

  I've only used the 9791 on a local network, where MAX auto-detection is, well, automatic.

  William Reed

  Thank you very much - that really help.

• WSN-3212 or NI WSN 3202 when loaded with VI target with

  WSN-3212 or NI WSN 3202 when loaded with a new firmware using option "Add LABView WSN target", cannot re connect with the gateway ethernet OR WSN - 9791. In MAX, the quality of the link state is "lost Signal".

  Basically, I tried to change the sampling in the sample interval ""case structure, then built the VI and deployed on two WSN nodes. " They show the status of the download of the firmware and the LABView also shows the message 'successfully deployed", but then, knots just to start scanning and never connect again.

  Please help in this regard.

  Hello binarystar105,

  When you have downloaded the new firmware, did you follow the steps described in this article?

  How to upgrade the Firmware on my NI WSN gateway?

  http://digital.NI.com/public.nsf/allkb/CF6241F5F849FC7086257909008327C5?OpenDocument

  Also, what version of firmware you currently have?

  What version of the LabVIEW WSN Module work?

  If you look at the properties of the node of your window from the LabVIEW Project Explorer, can set you the tab node sampling interval?

  You may already familiar with this material, but I found the following white paper to be extremely useful when I started working with WSN:

  Getting started with wireless sensor networks of NOR

  http://www.NI.com/white-paper/8890/en/

• How can I configure a port Ethernet NI9792 gateway to communicate with a cRIO CAP?

  Salvation OR engineers,

  I intend to use my gateway NI9792 in the following way:

  1. a single Ethernet port for network connection. That's how I'm developing, download the software and monitor my request through my PC in my office.

  2. the other port to communicate with a cRIO device? If so, how can I do it?

  It seems to be a stupid question, but I really couldn't work this!

  Thanks in advance,

  Luiz

  Good afternoon, Luiz

  Follow the first link to guide the module which can be used and other links to the best part of bore configuration CRIO. For any question, please contact us.

  How to set my time on the NI WSN-9791 or NI 9792 gateway server?

  http://digital.NI.com/public.nsf/allkb/44FA322FAFF8D58D862575BD00591A54?OpenDocument

  Configuration and NI WSN product guide
  http://zone.NI.com/DevZone/CDA/tut/p/ID/8710

  Configure the Ports of double Ethernet on real-time controllers

  http://digital.NI.com/public.nsf/allkb/67F94BB93BCE32CF86257367006B3659?OpenDocument

  video installation and installation CRIO

  http://www.NI.com/SWF/demos/us/cRIO/outofbox/

  Automatic configuration of network for the cRIO-9073 and cRIO-9074 CompactRIO controllers

  http://digital.NI.com/public.nsf/allkb/37C790309A210A748625757000570938?OpenDocument

  Sincerely,

  Mauro Vera.

• 36 wsn-3202

  Hello, dear OR engineers!

  There is a task to build net wsn with 36 x 3202 modules on a COMPACT territory and 9791gtw ~ 70x70meters, is it possible?
  (All documents are read, please visit)

  Problem is that all modules can 'see' radio signal each other in the small territory while it produces interferences and there is no possibility of separate wsn-routers.
  All modules are distributed on a square regular. WSN-9791 is one side of the square on a height of 8 m.

  Someone at-ideas? Or maybe sombody can convince me that such system is incorrect? Plan in attachments.
  Thanks for any help!

  
  

• WSN-9791troubleshoot erratic readings

  We have a WSN-9791 with four WSN - 3212 s. All 3212 s have power supplies OR (don't not running off battery).

  Three of the four 3212 s give erratic readings. For example, the following was recorded today to a piece that should be around 70F:

  17/10/2012-15:38:20 187,8
  17/10/2012-15:39:20 148.9
  17/10/2012-15:40:20 139,0
  17/10/2012 15:41:20 - 1548.9
  17/10/2012-15:42:20 37.2
  17/10/2012-15:43:20 158.8
  17/10/2012-15:44:20 39.5
  17/10/2012-15:45:20 111.5
  17/10/2012-15:46:20 206,4
  17/10/2012-15:47:20 - 6.6
  17/10/2012-15:48:20 188,6
  17/10/2012-15:49:20 262.5
  17/10/2012-15:50:20 74.1
  17/10/2012-15:51:20 102.0

  Location appears to play a role - so far two 3212 s different that give erratic readings have been very stable (with reasonable readings, too) when they sit on my desk, but become erratic when moved elsewhere in the building. In addition, one of the erratic nodes goes stable days, then several erratic days, then back to stable. When a node is erratic, all four thermocouples of this node are erratic.

  Thinking that this might be a problem with the electrical noise, I put one of the 3212 s on a UPS - no difference. I also changed the channel without wire used for a couple of different parameters, without modification. I moved the 9791 at different locations in the building, again no difference. Thermocouple type parameters have been triple checked.

  Any ideas on how to solve this?

  Hi James,

  WSN-3212 is sensitive to analog loops mass and power supply noise and maybe it's what you see. To determine if this is the problem, try the following.

  1. electrically isolate environmental thermocpule probes

  2. connect the ground terminal GND D of the WSN-3212 (PIN 10, 12, 14 or 16)

  See you soon,.

  Brian has

  R & D Product Support Engineer | WSN/network DAQ/University

  National Instruments

• change the node id error/bug

  I have a gateway WSN-9791 and 6 knots

  4 x 3226

  1 x 3202

  1 x 3212

  I sat the system at the office to test, I got the 3212 as ID1, and I gave all the nodes a name. Now, I moved the elements of the site where they work, but until the 3212 is no longer necessary. So now, I connect from a new computer to the gateway to implement my system of 5 knots. but now I have chaned the id of node of nr 5 to nr 1, but whenever I add, it appears like the 3226; added it comes with my old name of node and the old type :-(if I change it to a node id I never used then his work. does anyone know hoe to fix it?

  I tried to restart the bridge, droped the nodeds, added again... nothing helps.

  Hi Sivsko,

  Can manually add you the correct node type in the project?

  1 remove the tagged 3226 as 3212

  2. click right bridge in the Project Explorer and select new > targets and devices

  3. Select new target or device in the window add targets and devices

  4. Select the WSN node > NI WSN-3226

  5. give him a node ID 1

  You can also see if the creation of a new project solves the problem.

  1. close LabVIEW completely (to remove information in RAM)

  2 reopen LabVIEW

  3. open a new project.

  4. right click the project in the Project Explorer, and then select New > targets and devices

  5. Select WSN gateway > "your door."

  See you soon,.

  Brian has

  R & D Product Support Engineer | WSN/network DAQ/University

  National Instruments

• USRP can be used as a gateway for NOR-WSN nodes

  Hello world

  I use NEITHER-WSN kIT includes a gateway (9792) and of the NODES(3202,3212,3226 all programmable) NOR-WSN and I also try experiments with NOR-USRP 2921, so I thought to replace NOR-USRP 2921 of GATEWAY ETHERNET of NOR-9792 TIME REAL as it also works on the same 2.4 GHz.

  USRP 2921 can act as a bridge or not? This is possible, please suggest.

  Best regards,

  Afonso Sharma

  The short answer is no.

  The longer answer is that a WSN node uses a radio of fixed function with a full protocol stack.  The USRP is a generalist radio which covers a set of common frequencies, but there is no such thing as a fully functional turnkey battery.  It could be designed?  Maybe during many years-men targeted development.

  The USRP is mainly used as a search feature.  Most of the research implements a small aspect of a Protocol, ususally focus on the physical or the MAC layer, then it customizes and evaluates the results.

  The right solution for WSN is a WSN gateway.

  Erik