XP Home Edition. Click on "Finish" to complete the backup or Restore Wizard and get the error message "file of the recovery diskette could not be created. The operation has been aborted. "Impossible to correct the error. Any Suggestions?

Follow the instructions in MS, but is unable to perform a backup.

Hello

You can follow this link and check if the problem persists.

An Error Message appears when you try to use the Automated System Recovery Wizard

Hope the helps of information. Please post back and we do know.

Concerning
Joel S
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

Tags: Windows

Similar Questions

  • XP pro sp3 run asr, but didn't start; files for the recovery diskette could not be created

    I had previously asr has been successfully run on the same configuration but have decided to update the recovery data. I tried to restart the asr by clicking Start, all programs, accessories, system, backup tools. The Backup Wizard appears and I clicked on Advanced Mode. Then followed the backup utility page, I clicked on the ASR Wizard. The next page has been the preparation of Recovery Wizard, I clicked next and was presented with the option of backup destination and, after finishing the backup destination, I clicked Next. My page was last option; End of the ASR Wizard, I clicked Finish. Backup went into his usual preamble but almost instantly a warning box came up with the message "files for the recovery diskette can not be created." I am running xp pro sp3 as I had been for the creation of the previously successful GDR.

    I also tried using the Backup Wizard and I clicked on backup all information on this computer (this option automatically provides ASR) and followed the instructions of the wizard through to the end and the failure has been the same.

    I found a solution to my problem of ASR. If I was not able to create an asr backup, I was still able to run Ntbackup. I've saved my OS drive then ran repair with the XP Professional installation cd. Backup ASR works now.

    OK, I had to reinstall all them that updates the Knowledge Base Microsoft and also all the Service Packs. One or two of the plug-and-play applications were a bit annoying, but be as I have all the installation cd, other than being tedious, have all been re-installed and the system is now as good as new.

  • I get the message "files for the recovery diskette could not be created" when you use the backup utility. Why?

    I was using the Backup Wizard, backup all info on the computer to an external hard drive and insert a diskette in the drive.

    Hello

    · What is the edition of windows that you have installed?

    · What is the service pack installed?

    Try the steps listed in the link below: year Error Message is displayed when you try to use the Automated System Recovery Wizard: http://support.microsoft.com/kb/302700

  • "I get,' files for the recovery diskette can not be created ' and I can't save my PC

    When I try to back up my PC, I get "files for the recovery diskette could not be created" how to fix this?

    Hello

    This problem can occur because ASR is not supported in Windows XP Home Edition. However, users of Windows XP Home Edition can access the Recovery Wizard if they install the Ntbackup program in the Windows XP Home Edition CD-ROM Valueadd folder.

    See the steps listed in the article below and check
    An Error Message appears when you try to use the Automated System Recovery Wizard
    http://support.Microsoft.com/kb/302700

    I hope this helps.

    Thank you, and in what concerns:
    Shekhar S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.
    If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

  • How can I get rid of the error of the program could not initialize OXC0000135 framework 4 has been updated help please Mildred w

    Whwn I try to open a program like incredimail also Adobe Reader 9.

    I get the program was unable to initialize OXC0000135 I updated the framework 4

    who has not solved the problem. I can't update or uninstall.

    I tried a restore but who wouldn't let me go to the problem area.

    If I upgrade to windows 7, which would solve the problem?

    I am running Windows Vista. Help, please! Thank you, Mildred W

    Have you tried to uninstall Adobe Reader 9 and Incredimail?  There is an update to Adobe Reader 10.1.0

    http://get.Adobe.com/reader/

    Perform a clean boot.  This document shows you how to determine which third-party application is causing the problem?

    http://support.Microsoft.com/kb/929135

  • I need to install a driver on my computer. When it downloads it automatically is to open with excel and does not demand for correct installation. Any suggestions?

    I need to install a driver on my computer. When it downloads it automatically is to open with excel and does not demand for correct installation. Any suggestions?

    Hello

    1. for which device you are trying to install the drivers?
    2 are you able to install or run any .exe on the computer file?

    Try to run the fix to the article below and check if this help.
    When you run an .exe on a Windows Vista-based or Windows 7 computer file, the file may start another program
    http://support.Microsoft.com/kb/950505

  • I have an old iMac for 5 year with El Capitan and need to upgrade to Pages 5.6.1.to be able to open docs on my iPad. Everytime I try and open it on the Apple Store it just shows my old docs pages on the iMac. any suggestions?

    I have an old iMac for 5 year with El Capitan and need to upgrade to Pages 5.6.1.to be able to open docs on my iPad. Everytime I try and open it on the Apple Store it just shows my old docs pages on the iMac. any suggestions?

    The App Store has to do with your documents?

    The App Store allows you to buy and download Apps, as its name suggests.

    Peter

  • I tried to run Check Disk and get an error message on the completion of the phase 2

    I tried to run Check Disk and get an error message on the completion of the phase 2. If I try to run a defrag without having completed verification of the disc it comes up with error message Disk Defragmenter has detected Chkdsk is scheduled to run on the Volume: c. Please run f / dskchk. I tried to run it and nothing seems to happen. I checked that I have no other programs running and she thinks that this is the case.

    * original title - I check disk / defrag problems *.

    Kevin.

    How old is the hard drive? It is still under warranty? The easiest way forward is to replace the drive.

  • Impossible to follow all the links, get the error message "this operation has been cancelled due to restrictions on this computor"

    I get the message "this operation has been cancelled due to restrictions on this computor" any time that I try to follow a link.

    No idea comes the restriction and how can I turn it off?

    Hi P Coyne,

    1 does happen with all hyperlinks?

    2. did you of recent changes on the computer?

    3. what web browser do you use to open hyperlinks?

    Try the steps in the Microsoft article if you have a problem with hyperlinks in Microsoft outlook.

    You receive an error message when you click a hyperlink in Outlook

    http://support.Microsoft.com/kb/310049

  • The backup has failed. An error has occurred. The following information can help you resolve the error: the request has been aborted. (0x80099704D3)

    Hello, I am running Windows Vista Home Premium and trying to make Windows backup on DVD, I was able to cross 5 DVDs then it asked me to insert the DVD successfully n ° 6 I did and he never finished and I got this error:

    The backup has failed. An error has occurred. The following information can help you resolve the error: the request has been aborted. (0x80099704D3)

    The DVD I have are DVD so I can't rewrite over and over again. Can I somehow he pick up where it left off to complete my backup?

    Help! Thank you

    Lisa

    Hello

    -No, I don't have third-party backup programs installed.
    -J' tried using another disk backup, but it started it count once again as "disk 1" yet I had left off to "drive 6"and I couldn't tell if he has taken over where I left off or starting on even once, I don't want to do because I can't rewrite on my DVD. , because they are disposable.
    Because I needed to achieve this, I advanced and bought more DVD and will continue to backup even if I do not know where she had stopped. I think I can say that it not continue starting above and to the right.
    I think that the problem might have been that DVD #6 was bad, as he had a scratch on her, even if it was new out of the envelope.
    Software AV is not the issue, I am able to do backup, I wanted to just be able to pick up where I left off, as opposed to duty again since the beginning of my documents again. I just wish that Windows backup has been a little easier to use, in particular the fact that it is not "tag" my files to show who we are it is already saved, just like other software, (ex Mozy), which is very useful. And be able to choose what files I need backup rather than being limited to simply choose the 'file type '...
  • Try to install the patch KB943729 and get this error. __

    Try to install the patch KB943729 and get this error.

    The upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded is may be missing, or the upgrade patch may update a different version of the program. Verify that the program to be upgraded exists on your computer and that you have the correct upgrade patch.

    Any help with this error.

    I've always found the icon on my Start button that indicates that an update is ready to be loaded and I have to restart my computer

    Open Internet Explore (only) to http://support.microsoft.com/kb/971058 & re-run the difficulty in AGGRESSIVE mode. [1]

    Reboot once more & test.

    ~~~~~~~~~~~~~~~~~~~~~~~~
    [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not the list of installed updates.

    ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

  • Restore error 'file \minint\System32\kdcom.dll could not be loaded. The error code is 4 "

    Hello...

    I have a DELL D830 with XP and I get the message:

    File \minint\System32\kdcom.dll could not be loaded. The error code is 4.

    Everytime I try and restore my computer...

    What can I do to fix this, that does not cost a lot of money?
    The only cost of $180 (refurbished) computer... I really don't want to pay that much to fix this...

    It sucks, virus SUCK!  Why do people do the virus? (it seems lame)

    Help, please!

    I had installed security trend, however apparently the virus that caused this exceeded the trend...

    Hi NickRider,

    Follow these methods.

    Method 1: Performs a search using the Microsoft safety scanner.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

    Method 2: Disconnect all external devices and try to start the computer.

    Method 3: Follow these steps:

    Step 1: Start the computer in safe mode and check if the problem persists.

    A description of the options to start in Windows XP Mode

    http://support.Microsoft.com/kb/315222

    Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

    How to configure Windows XP to start in a "clean boot" State

    http://support.Microsoft.com/kb/310353

    Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

    After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

    (a) click Start, run.

    (b) type msconfigand click OK.

    (c) the System Configuration Utility dialog box appears.

    (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

    (e) when you are prompted, click on restart to restart the computer.

    Method 4: Follow the steps in the article to check the drive for errors.

    How to perform disk error checking in Windows XP

    http://support.Microsoft.com/kb/315265

    Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

  • Error.' c:\docume~'\earl\locals~1\temp. A temporary file needed for initialization could not be created or cannot be written in ' when try to run 16-bit programs in windows xp computer at home.

    original title: 16-bit windows subsystem error

    I was able to run 16-bit programs on my computer with windows xp home edition. now when I try to open the program I get a 16-bit windows subsystem error. c:\DOCUME~'\earl\locals~1\Temp. a temporary file needed for initialization could not be created or cannot be written to. Make sure that the path exists, and the space is 'close' to teminate the application available.choose

    Hi EarlBettencourt,

    You can follow this link & check if the problem persists:

    Error message when you install or start an MS-DOS-based program or 16 - bit Windows based

    Hope the helps of information.

  • When you try to schedule a task in XP, make a mistake "the new task could not be created the specific error is 0x80070005: access is denied."

    My

    System Type X 86-based PC
    Processor x 86 Family 6 Model 23 Stepping 10 GenuineIntel ~ 3324 Mhz
    A05 BIOS Version/Date Dell Inc., 07-31-2009
    SMBIOS 2.5 version

    I'm trying to schedule a new task I get this error

    The new task could not be created specific error is 0x80070005: access is denied

    I am an administrator for this computer and I am connected to the office network.

    I downloaded a patch KB904423, but it tells me that the installer has detected that the SP of the system version is newer the updte I am applying, I did not need to install this update

    Is there any fix for this?

    Thank you

    Hi dgxp64,

    ·         The computer is on a domain network?

    Method 1: Temporarily disable the antivirus on the computer program and check if it helps. If it works, you may need to check the settings of the program.

    Note: Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.

    Method 2: Check to see if this article helps you.

    How to solve the scheduled tasks in Windows XP and Windows Server 2003

    Method 3: We will grant permission for the C:\Users folder and check if it helps.

    How to set, view, change, or remove special permissions for files and folders in Windows XP

    If the computer is on a domain network you can post your query on the TechNet Forums.

    Windows XP IT Pro category

  • Vista error "this operation has been cancelled due to restrictions in effect on this computer. Contact the administrator of the system to you. When you try to open Avira Antivirus and Windows Defender".

    Whenever I try to open Avira Antivrus and Windows Defender, I get this message: "this operation has been cancelled due to restrictions in effect on this computer.  Please contact your system administrator. "I am the administrator and I have not set restrictions.  It worked, but started recently and I can't find answers.  All solutions?

    Hi I_GHall

     

    It seems that you receive the message you want to software conflicts. I suggest you try to disable either the Avira antivirus and windows defender and then check if the problem resolves.

     

    If you disable any security software for troubleshooting temporarily, so don't forget to activate after troubleshooting is completed that your computer will be at risk.

    See the help link - below
    http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

     

    I hope this helps.

Maybe you are looking for