XP without error UNMOUNTABLE_BOOT_VOLUME Office icons. When the safe boot mode.

Similar Questions

• Blue screen, but can the safe boot mode

  I get the following error

  

  He then gets to my home screen, just before going to my office and then I get the blue screen:

  I am able to boot in safe mode.  I also tried boot of the last good configuration but still knowing the blue screen.

  Please help because I am stuck how to proceed!

  Hello

  Check your cables to the disk hard (on both ends) - remove and replace - do

  not only it to be tight (of course all power first deleting).

  --------------------------------------------------------------------------------------------------------

  Resolution in Windows 7 stop errors (blue screen) - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  We can analyze the minidumps if make you it available from the OneDrive or other
  file -sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  Adding files to your OneDrive
  http://Windows.Microsoft.com/en-us/Windows-8/getting-started-onedrive-tutorial

  A disk - sharing files and folders and change the permissions
  http://Windows.Microsoft.com/en-us/onedrive/share-file-folder

  ZIP or download the content of the C:\Windows\minidump

  Use OneDrive to upload collected files

  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  --------------------------------------------------------------------------------------------------

  BCCode: 50 0 x 00000050

  References to Vista also apply to Windows 7.

  Have you recently added any hardware? Have you updated a driver just before
  These began? (Check control panel - updates of Windows to see if all drivers
  have been updated it there all the time, it started) main likely culprits are video
  pilot, other great drivers, memory and antivirus/antispyware/security products
  could be faulty as well as reader questions.

  Use the troubleshooter below and refer to the following message for pilots and
  memory when you get these sections and then return of the disease.
  game needed.

  BCCode: 50 0 x 00000050

  Bug Check 0 x 50: PAGE_FAULT_IN_NONPAGED_AREA
  https://msdn.Microsoft.com/en-us/library/ff559023%28V=vs.85%29.aspx?f=255&MSPPError=-2147217396

  BCCode: 50 0 x 00000050<-- read="" this="">
  * 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods above
  It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
  Ultimate and Enterprise)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• Windows 7 is the safe boot mode; How can this be repaired?

  Original title: program compatibility Application Applications App Apps game games Legacy Crash crashes Hang hangs

  Why Windows is open in safe mode, can it be fixed.

  You can access the SafeMode normal mode by selecting Start, run, type msconfig and press the ENTER key. Click on the Startup tab and check the box before the secure startup, click apply and then click OK and restart your computer.

  To return to the normal mode, you follow the same procedure except that you uncheck the box before the secure boot.

• When you try to install the------creative cloud without error 1. What is the problem?

  When you try to install the------creative cloud without error 1. What is the problem?

  Error code 1: "unable to install". Creative Cloud Desktop: https://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html

• Bug: Trash does not display 'empty' icon when the Recycle Bin is emptied.

  Bug: Trash does not display 'empty' icon when the Recycle Bin is emptied. This only happens when you use customized for the trash icons. The Recycle Bin appears correctly when office is updated.

  It would be nice if someone could answer this question, as it is 8 months old.

  Click Start, type regedit.exe, and then press ENTER.

  Reach:

  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\CLSID\ {645FF040-5081-101B-9F08-00AA002F954E}

  Export the branch above into a REG file.

  Exit Regedit.exe

  Open the REG file with Notepad, copy the content and include it with your answer.

  Ramesh Srinivasan . The Winhelponline Blog
  Microsoft MVP, Windows desktop experience

• My computer won't allow me to access my files on my portable hard disk without error appear "you must format the E: drive before using it. How can I fix this please!

  My computer won't allow me to access my files on my portable hard disk without error appear "you must format the E: drive before using it. How can I fix this please!

  Try to scan your driver with anti-virus, also try to throw the disc looking for this driver and as you try to run the following tools:

  http://support.Microsoft.com/mats/system_maintenance_for_windows/

  http://support.Microsoft.com/mats/windows_file_and_folder_diag/

• I have an error msg "Unable to connect to the firewall local host control" is displayed when the system boots

  OS - win7 family Basic 64-bit

  anti virus-macfee
   
  Original title: I have an error msg "Unable to connect to the firewall local host control" is displayed when the system boots. MacAfee antivirus, 1 GB Radeon graphic

  McAfee has been updated at the same time as the last batch of updates from Windows 7 and it seems to be the cause of this problem for most, if not all, users.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I got McAfee, but the connection has started working again on its own so I thought I was clear of problems. However, when I checked it says he was doing routine checks the updates in vain when I told it to do a manually. So stick with McAfee you don't follow their procedure of fix would have upgraded my PC at risk by not updated and, like other McAfee ads have since explained, the application did not refer to its database of threats correctly [and this could explain part of the variability of the symptoms of failure but all involved loss of internet connection]. Actually, I removed McAfee then installed Microsoft Security Essentials rather & my answer IE is faster I knew it [even though I had the Add-ons McAfee disabled for centuries].

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• In Safari, I get the error code BSO D 0 X 80060402, error code Windows defender in the available boot device. He told me to contact Microsoft certified technicians. I do not use Microsoft or windows.

  In Safari, I get the error code BSOD 0 X 80060402, error code Windows defender in the available boot device. He told me to contact Microsoft certified technicians. I do not use Microsoft or windows.

  You have utilities installed on the computer antivirus, cleanup, or other third party maintenance?

• Various recurring error messages blue box when the laptop is idle

  I have a new (10 months) HP Pavilion dv7 - 3165dx running windows 7 home premium 64-bit.  After that laptop sitting idle for a while, the screen goes black with a blue box error message.

  01/02/11-02/14/11

  Error message: A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this stop error screen, restart your computer.  If this screen appears again follow these steps:

  Disable or uninstall any antivirus, commercial defragmentation or disk backup.  Check the configuration of the disk hard yoru and check the updated drivers.  Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Call Technical Support HP - a talked to Josh: I was sent to HP.com support site to download software downloads and the pilot.  Said it is known the problem and had me run the CHKDSK command to automatically solve problems.

  02/16/11

  Error message: A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this stop error screen, restart your computer.  If this screen appears again follow these steps:

  Make sure you have enough disk space.  If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates.  Try changing video cards.

  Check with your hardware vendor for updates to the BIOS.  Disable the BIOS memory options such as implementing caching or shading.  If you need to use safe mode or remove or disable components, restart your computer, press F to select the advance boot option, and then select Safe mode.

  Technical information:

  Stop: OX0000007E (OXFFFFFF800032D3905, OXFFFFF88002B97288, OXFFFFFFFFC0000005, OXFFFFF88002B96AFO)

  Data collection for the crashdump...

  Call the HP Technical Support - talking to Matt: check space drive, and said that it was very good.  Updated graphics driver.  Disabled the hard drive protection.  Power options reset of Hibernate to standby mode.  Update BIOS of F.10 F.15.  Ran test drive: Smart check, DST short and long DST all spent.

  02/17/11

  Error message: A problem has been detected and windows has shut down to prevent damage to your computer.

  System_Service_Exception

  If this is the first time you've seen this stop error screen, restart your computer.  If this screen appears again follow these steps:

  Check to make sure any new hardware or software is installed correctly. If it is a new installation, ask your hardware manufacturer or software, the windows updates, you might need.

  If problems continue, disable or remove any newly installed hardware or software.  Disable the BIOS memory options such as implementing caching or shading.  If you need to use safe mode or remove or disable components, restart your computer, press F to select the advance boot option, and then select Safe mode.

  Technical information:

  Stop: OX0000003B (...)

  Data collection for the crashdump...

  I don't ' know what to do at this point.  HP phone support seems unable to solve my problem.  Can someone help me?

  Hi DP - K,.

  Thank you for all the helpful tips.  This weekend when I saw my McAFee scan/security reports, even if the McAfee Security Center shows that viruses and spyware works, he did not run a weekly full scan on my laptop since the end of January.  I don't know if he tried to scan and then breaks down, or it will not start.  When I tried to run a manual scan, windows shut down and I got a blue screen error message after about 5 hours of scanning - 63% digital.  When I ran the HP System Diagnostics report, it showed that my Security Center has not recorded an antivirus product.  "The Security Center cannot identify a current antivirus application.  There is no product protection antivirus installed or it is not recognized. "When I ran the HP reliability and history of problem report, it showed that my error messages started on 01/02/11, which is what I remembered.  I was able to restore my laptop to 23/01/11 when I had no problems and then, I uninstalled McAfee security and re-installed software.  I manually ran a full scan and it took 5 hours to complete, it has completed and reported no problems.  I look today and so far, no problem.  If the problem happens again, I will try the suggestion of Avast below.   Thanks again for all your great suggestions.

• I get error-200077 Daqmx Read when the scale should be understood

  I have an application that uses a custom scales and NOR-9215.  The tasks and scales are that all configuration programmatically.  I get an error that GOT it. The min value is out of range, but when I check my graduation, it seems that it should be fine.  I have attached an image with the error message and also the scaling that I use (slope and offset) for each channel.  I calculated the permitted maximum and minimum values for each of the 3 channels based on the range scale and min/max of the 9215 (+/-10 v).  For all channels, I try to put the AI. Min = 0 and AI. Max = 13, but I get the error message even if these values are within the calculated range.  Is there something else I'm missing?

  Thank you
  Dan

  Solved

• How to re-create the show the office icon in the taskbar. Was there but missing

  The desktop icon Show that is usually at the base in the bar spots disappeared.  I tried to put it back, but what I got was an icon with the word Office only which does appear in the list, and does not go to the screen, forcing me to minimize all windows.  How can I get him back?

  The desktop icon Show that is usually at the base in the bar spots disappeared.  I tried to put it back, but what I got was an icon with the word Office only which does appear in the list, and does not go to the screen, forcing me to minimize all windows.  How can I get him back?

  Use this tutorial:

  http://www.Vistax64.com/tutorials/70009-show-desktop.html

  The tutorial is to create a shortcut to show the desktop on the desktop. You can then drag the shortcut in the quick launch area.
  Click on the link that says... How to use quick launch in Vista.

• Desktop icon when the program double clicked States not recognized go to control panel of the value binding

  I have a PC running windows vista. Recently, the desktop icons when double clicked do not work, a message appears telling me that the program was not found and to go to the association Control Panel to fix this value.

  I'm now PC expert so would appreciate any advice in simple terms.

  It happens with all the desktop icons, or only some?  If only some, what are their types of files (extensions - the identifier to three digits after the point in the name of the file)?

  Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates. Then see if you can open your desktop icons.

  There may be something wrong with some extensions (such as .exe files and the .lnk files).  Go to http://www.mydigitallife.info/2008/06/22/reset-and-fix-broken-windows-vista-file-ext-and-type-associations-include-exe-com-sys-zip-lnk-folder-drive/ and run the process for the .exe and the .lnk file types. ;  See if you can open your desktop icons.

  If this does not work, your user profile may be damaged.  To fix this use http://windows.microsoft.com/en-AU/windows-vista/Fix-a-corrupted-user-profile.  If that is the only available Administrator Profile (you need to be an administrator to fix this), enable the Hidden Administrator Account (HAA) using http://www.microsoft.com/communities/newsgroups/en-us/default.aspx?&lang=en&cr=US&guid=&sloc=en-us&dg=microsoft.public.windows.vista.administration_accounts_passwords&p=1&tid=d20f9db4-7b2c-48be-a087-7835dc2a9055&mid=d20f9db4-7b2c-48be-a087-7835dc2a9055.  If you don't remember the password, try nothing because that's probably what you (or seller) did during the installation.  Once that is done, don't forget to disable the HAA to save it in case it is necessary once again and for safety reasons (since people often try to hack into systems using this account).  Do NOT use the HAA as your administrator account because if you lose the only administrator on the system account or it is damaged again, then you're watered.  Then see if you can open your desktop icons.

  If you still have problems, after return and we will try other troubleshooting options.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Popup disble icon when the cut or the variation in volume via keybord on Dell Latitude E6430

  Hello

  Is there a way to disable the icon that appears on the screen when I press the buttons sounds on the keyboard?

  I made a snapshotcompare of the registry when I cut and it shows the path:

  HKLM\SYSTEM\ControlSet001\Control\Class\ {4D36E96C-E325-11CE-BFC1-08002BE10318} \0001\Settings\filter\SpeakerHp\MasterMute: 00
  HKLM\SYSTEM\ControlSet001\Control\Class\ {4D36E96C-E325-11CE-BFC1-08002BE10318} \0001\Settings\filter\SpeakerHp\MasterMute: 01

  But I can't find any key associated with the icon that shows when I cut. And I want just the disabled icon, not the function.

  Can I do this?

  / Alfred

  I have a Latitude E5420. Mine came with "Dell System Manager' installed - it's in the start menu > all programs. If I click on it, then on 'system and Device Manager. "

  Open 'Display settings', then 'Notifications' uncheck 'Volume', the display of the volume no longer appears when I press the volume buttons.

  If you don't have it but you want to try, go to the E6430 download page, select Windows 7 64 bit operating system and then expand the category of Control Point. I don't think that there is a version for Windows 8.

• Error 907 invalid cod when the OTA

  Hello

  I have a problem with OTA Download on
  v4.1.0.268 (Platform 2.2.0.112).  BB 7250 on cdma network.
  It says Error 907 invalid cod

  the jar/jad/cod are created with JDE 4.6

  However, I can do OTA using BB 9000 download emulator with the same files / same url.

  I followed the diagnosis mentioned in
  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800708/800646/support...

  all sizes are correct in the jad file. I so should something specific to older devices BB when I deploy the applications of OTA?

  Here are the jad:

  Manifest-Version: 1.0
  RIM-COD-Module-name: TestSpeed
  RIM-COD-Module-dependencies: net_rim_cldc
  MIDlet-Jar-Size: 30100
  MIDlet-1:.
  RIM-COD-creation-Time: 1224023296
  MIDlet-Jar-URL: TestSpeed.jar
  RIM-COD-URL: TestSpeed.cod
  RIM-COD-SHA1: ef 3 b 05 31 and 21 a5 a7 9 d 3 c 4 c 6 c ed 6 d a6 bf 1B d3 a8 3f e0
  RIM-COD-size: 26200
  Microedition-Configuration: CLDC-1. 1
  MIDlet-Version: 0.0
  MIDlet-name: TestSpeed
  MIDlet-vendor:
  Microedition-profile: MIDP-2. 0
  RIM-MIDlet-flags-1: 0

  It's okay that APIs are used (the cod itself file format has changed along the way).  Please visit the following link.

  What is - an appropriate version of the BlackBerry JDE
  Article number: DB-00537

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800901/What_Is_-_Appr...

• Vista desk top of page monitor screen remains black when the computer wakes mode standby

  Windows Vista Edition Home Premium

  Dell desktop

  Intel Q8200 @2.33 GHz processor

  6.00 GB RAM

  32-bit operating system

  Type of card ATI Radeon HD 3450

  Driver update has been installed without any problems.

  When my desk top comes out of fashion 'sleep' (using the mouse click), I hear my computer turns (beeps once and can hear the hard drive and fan), but can not get the screen on the monitor to display (rest is black). Can only crash the system to get everything back to normal. I searched in internet and microsoft forums but didn't find a solution. Please help, it seems that many others also have this problem without solution. I like to use "sleep" mode and do not want to resort to turning off the sleep mode option.

  Hello

  Please provide information for a better understanding of the issue.

  1. what was the recent change in hardware or software performed on the computer before the question?

  2. are you having the same problem when you Hibernate the computer?

  Check the display driver for power management problems.

  Method 1

  Check if allow this device to wake the computer is checked in the Device Manager.

  a. click Start, type Device Manager in the start search box and press ENTER.

  b. Select graphics cards, it will display your display driver, right click and select Properties.

  c. Select the power management tab.

  d. check the allow this device to wake the computer check box.

  e. repeat these steps for the network adapters and the mouse as well.

  If the problem is not solved then continue to.

  Method 2

  Remove both power on your computer and check to see if that fixes the problem.

  Reference:

  Change, create, or delete a power plan (scheme)

  Try to create another plan of the power of your computer and check if the problem persists.

  Power plans: frequently asked questions

  See also (additional links for more information),

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/blank-screen-after-Vista-went-on-sleep-mode/b5e5693a-28a6-4391-b9ac-36d345d6a3b9?msgId=a464f2ec-0651-4E2F-8CB0-f546b09b0989

  Hope this helps