Yellow triangle with! the wireless network connection in the task bar icon, but ok in Device Manager

I still need help: 11-24-10' uncorrected problem after all

I have a laptop of refurbished HP older Pavilion ze5385US who has recently lost the wireless connection.  Now, I have to leave it plugged in to use, not practical at all.  I did the right click on the icon to open the network connections, left clicked wireless network connections and then clicked "repair this connection.  The uninstaslled of the computer, and then was not able to reinstall.  When I checked D, it was empty.  I thought it was where restoration stuff should have been.  So I downloaded and reinstalled much Express IEEE 802.11 PCI card Lan, until I found the one that the computer would be except.  Now, it appears in device very good Manager, but has theyellow cone with! on the icon in the status bar at the bottom.  When I raised it lights, it is said: 13 of (ANY) wireless network connection, speed: 11.0 Mbps, Signal strength: Excellent, status: limited or no connectivity.  When I choose "View available wireless networks", I get "Windows cannot configure this wireless connection.  Under network without wire/support/details of connections, Iget physical address: 00-02-8A-92-BE-0C, IP address: 169.254.196.112 subnet mask: 255.255.0.0, then the default gateway, DNS server, WINS server & have not enumerated values. I'm afraid to hit the repair again, it could wipe out the only map I've found so far that is accepted by my computer.  When I try to enter the knowledge base for WinXP, I get an error for this page, as well as several other help pages I tried the site of microsoft.com for help.  When I used configurationtool thewireless zero in respect of services & restart earlier, I had a red X on my icon, so I guess I've lost my card after all.  Can I disable this?  The map always shows as OK in Device Manager.  Any ideas anyone?  I need help here please.

Hello

I thank you and wish you the same.

I see that your problem has been solved using the HP driver that you mentioned on Thursday, November 18 in your message and the Express.sys is a problem with Windows install.

I suggest to install the version of Windows install 4.5 on the system from the link below and then update the driver from the link that was attached to your question before and check.

 

Step 1:

Install windows install 4.5

Windows install 4.5 Redistributable

http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

Step 2:

Update the driver from the link you mentioned in your previous post.

I suggest you to check with TP-link if this model is compatible with Windows XP or not.

http://www.TP-link.com/products/ProductList.asp?class=WLAN#S6

Thanks and regards.

Thahaseena M
Microsoft Answers Support Engineer.
Visit ourMicrosoft answers feedback Forum and let us know what you think.

Tags: Windows

Similar Questions

  • Problems with vista wireless network connection.

    Whenever I try to access the internet via unsecured wireless network I have to reset the modem/router.  Only happens with Vista and does occur only on that network.  No problem on other networks (public) wireless and no problem at home with 3 other computers on this router wireless and internet.

    Hi Skip,

    A. when it last work very well?

    B. has been any changes made to your computer recently?

    C. don't you check the network connection?

    D. is in monitor mode wireless network card?

    Try the methods below.

    Method 1

    The tool the Network Diagnostics which is part of Windows Vista is designed to test the network connection to find errors. The Network Diagnostics tool can also be used to determine if the network-related programs are working correctly. To use this tool to resolve network connectivity problems, follow these steps:

    1. Open Internet Explorer and try to access the Web page that causes network connectivity problems.
    2. On the page that displays an Internet Explorer error message, click diagnose connection problems .

    The Network Diagnostics tool will run. When the tool has finished, it will notify if you one of the following results:

    • He was unable to find a problem.
    • It has detected a problem. In addition, the tool will provide guidance on the next steps to take to resolve the problem.

    Method 2

    Open the link below and click the Fixit who can fix most of the issues related to internet explore.

    http://support.Microsoft.com/kb/936211

    Method 3

    Follow the steps in the article.

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

    Hope this has been helpful.

    Thank you
    Bindu S - Microsoft Support
    Visit our Microsoft answers feedback Forum and let us know what you think

  • During an update to Windows Vista, my office has disappeared with the task bar and start menu.

    I can only access my and other programs through the Task Manager.  I have tried troubleshooting, I restore my computer on the eve of what has happened, but nothing helps.  Any ideas?

    Hi cthodges

    Thank you for using the Microsoft Answers Forums!

    I would like to ask you a few questions to help focus in the right direction:

    Are there other specific details that you can provide that will help us understand and solve your problem?

    We can try a few steps and check if it works:

    Run explorer.exe from the Task Manager > new > task. If the start menu reappears, it would confirm the cause.

    We can now perform the following steps:

    Step 1:

    Run an on-line analysis of your PC of malicious software:

    If you want to scan your computer for malware and potentially unwanted on a Web site, please use the Windows Live OneCare safety scanner.

    Windows Live OneCare safety scanner is an online service that lets scan you your computer to protect yourself, clean and operate at its best. Use our free protection scan to check and remove viruses, spyware and other potentially unwanted software and to find vulnerabilities in your Internet connection.

    You can also run Anti-Malware on your computer. Follow the steps in this link:

    http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/ba80504b-61f1-4D71-960f-b561798b7b42

    Step 2:

    To use a boot option, follow these steps:

    a. restart your computer and start pressing F8 on your keyboard. On a computer that is configured to start to multiple operating systems, you can press the F8 key when the Boot Menu appears.

    b. Select an option when the Windows Advanced Options menu appears, and press ENTER.

    c. when the boot menu appears again, and the words "Safe Mode" appear in the bottom, select the installation that you want to start and then press ENTER.

    If it works fine in safe mode, infer you that all third-party programs are causing the problem.

    Put the computer in a clean boot (namely if any third-party software hinders the process)

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Check with step 1 (run a clean boot):-If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

    Continue with the remaining steps to pin-point on the third party service.

    (Note: after find you the problem causing the program, you will have to perhaps to update or install a newer version of the program and also don't forget to put the computer to a normal startup)

    S tep 3 :

    The SFC utility allows administrators to perform an analysis of all protected resources to make sure they are the correct version. Whether SFC should find all incorrect versions in one of these protected resources, SFC will be replaced by the correct versions.

    You can still run a sfc on the windows vista computer scan. To run a scan suite sfc as follows:

    a. Click Start, in the start search bar type cmd, right-click on the command prompt icon in the box programs and then click Run as administrator.

    b. at the command prompt type sfc/scannow , and then press ENTER.

    See this link for more information:

    http://support.Microsoft.com/kb/936212

    Hope this information was useful.

    Let me know if it worked.

    All the best!

    Thank you and best regards,

    R uma - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • in the right user account after the connection in the task bar icon flashes "windows need your permission to continue".

    I got a virus in my Vista computer cse.exe the so-called fake-AntiVirus. He has changed the file association for exe files. I fixed it and and deleted the program as well as its footprint in the registry. The virus attacks when I was in a non-administrative account. Therefore, any changes made to the registry were in the CURRENT_USER section.
    Still a problem. If I connect as User1 [non-admin] before any other action is taken, I see a tab flashing in the taskbar. It says "Windows needs your permission to continue". If I try to remove it the Explorer window dies and I get a clean screen with wallpaper and I have to restart. Of course if I provided the 'root' password every thing seems OK. I tried to identify any processes that can ask something looking at the tables Task Manager but don't see anything suspicious. If I do not touch the flashing tab I open the other Wndows Explorer since the icons I have on the desktop and NOT additional UAC asks pop up. The computer so that these experiences if offline. There is an another non administrator account on this computer. If I connect you no problem can be observed. Everything happens only in the account where the virus attacked.
    Any idea? Can I find out what program is doing admin type of request?
    Victor

    Hi Victor,


    How to remove the virus from the computer?
    I suggest you to follow the steps and check if it helps.

    Method 1: Scan your computer with Microsoft Safety scanner for viruses and check if that helps.
    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.
     
    Method 2: Run check file system (CFS) analyses and checks to see if it helps.
    http://support.Microsoft.com/kb/929833

    Note: SFC system gives an administrator the ability to scan the files all protected to check their versions. If the System File Checker detects that a protected file has been replaced, it retrieves the correct version of the file in the folder cache (% Systemroot%\System32\Dllcache) or the Windows installation source files and then replaces the incorrect file. System File Checker verifies and repopulates the cache folder also. You must be logged in as an administrator or as a member of the Administrators group to run the System File Checker. If the cache folder is damaged or unusable, you can use the sfc/scannow, sfc /scanonce or commands sfc /scanboot to repair its contents.
     
    Method 3: To fix an account corrupted, please follow the steps in the link and check if that helps.
     
    Method 4: To find out which program makes admin request type, check Event Viewer and check if that helps.
    Open event viewer
  • Several months ago the button, if that's what it's called, the task bar that displays hidden icons has stopped working.

    Original title: the task bar icons

    Several months ago the button, if that's what it's called, the task bar that displays hidden icons has stopped working. Can I get a virtual device driver format in the registry is incorrect when you use a disk with the drivers on this subject. I found information on how to correct this problem and now the botton of task bar work again although it works until the computer is used for a while. How is the hidden icon button suppose to work or it should be visible all the time? Also the virtual device driver registry entry has something to do with it? I think that the problem of the DMV has installed a Norton program antivirus software that was on a disc that came with the computer.

    Hello

    1 have had any changes made to your computer before this problem?

    I suggest you try the methods mentioned below and check if it helps:

     

    Method 1:

    You can also scan your computer the Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

    The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

    http://www.Microsoft.com/security/scanner/en-us/default.aspx

    Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

    Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

    Hope this information is useful.

     

  • My Windows XP home edition with service pack 3 now displays the status of my absorbing as "State of the network" wireless network connection but never connects to the network.

    My Windows XP home edition with service pack 3 now displays the status of my absorbing as "State of the network" wireless network connection but never connects to the network. This started after my last Microsoft update has been installed. .

    original title: status: network address acquisition
    Hi BKlap,
     
    Try these methods in the order.
     
    Method 1: Repair the network connection to solve the problem.
    For more information, see:
     
    Note: The information in the article applies to Windows XP Home Edition as well.
     
    Method 2: Follow the steps listed in this article to resolve the problem:
  • my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card

    connection network card

    my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card... I'm not sure how to solve the problem of the dat

    Hello

    Did you change your computer?

    I suggest you to follow the links and check out them.

    The problems of Internet connection

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

    Solve problems, find wireless networks

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

    Windows wireless and wired network connection problems

    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    Tips for solving common driver problems

    http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems

  • A yellow triangle with an exclamation point indicates no Internet connection

    Hi, I have a 2nd computer in my attic and never had any problems with a Wi - Fi connection... So far! I just got this yellow triangle with a point of exclamation and no Internet connection. My laptop is fine with the WiFi... So I'm puzzled... Any ideas would be accepted with gratitude... John was soon

    Original title: wireless connection

    Take a look at this example of configuration of wireless network card, hope might give you more ideas.

    I hope this helps.

  • NJR, I have installed connectify on mn pc connection sharing software 2000 computer hp laptop, but it displays a yellow triangle with AP not supported. What do I do?

    Hi I have installed connectify on mn pc connection sharing software 2000 computer hp laptop, but it shows me a yellow triangle with Ap not supported, what to do?

    Hello

    You asked your question in the text of the Microsoft Community. Please could you click on the globe icon to the world (change region) at the bottom left of the screen and then choose your preferred language. Now ask you question once again.

    Thank you.

  • Said connections wireless network connection are available, but the networks to connect to are no longer visible in the connection

    I got a new laptop from work and have connected a couple of times on our network.  Now, he does not connect through the wireless network connection.  He said that the connections are available, but there is no connection available more in the list.  If you have to manage wireless networks, it is in the list... but you can not log in via this page.  Any help would be grateful.

    Thank you!

    Hello

    1. what operating system you are using?

    2. how many computers is connected to the network?

    3 - is a domain network?

    4. What is the exact error code or error message you received?

    5 have have there been recent changes made on the computer before the show?

    Follow the steps mentioned below and check if that helps.

    Method 1: Troubleshooting run Network.

     

    http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

     

    Method 2: Wi - Fi and in Windows network connection issues.

    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

    If you cannot connect to a network, it could be a problem with your network adapter. You can try to use the network adapter troubleshooting utility to automatically find and fix some common problems.

    How can I troubleshoot network card?

    http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems

    Method 3: Disable the security software and check.

     

    You can also temporarily disable the security software and check if the problem persists. Be sure to enable this security software on the computer after checking.

    http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

    http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

    If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

    Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

     

    For more information, please see the following links:

    http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-a-network

    http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

    http://Windows.Microsoft.com/en-us/Windows7/add-a-device-or-computer-to-a-network

    http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions

    I hope that helps!

  • Get rid of the current wireless network connection so that I can set up a new connection using the same IP address.

    Here's my problem: I got a new computer and a wireless network connection has been set up and I could get on the internet. My daughter then wanted to try her new computer and somehow his computer is defined as the network and I can no longer connect to the internet via my computer.

    The second part of my problem is that when I try to configure my computer, I get the message that I need to go to the Micro knowledge base and article 871122.
    I did it.  By following the instructions for Windows configure my wireless, I get as far as the stage of network connections - go to change the settings for this network connection.  It is said that I had to go to the wireless network tab.  There is no tab wireless network I can say to use Windows to configure my network connections...

    I know it is long, but can someone help.  I use Windows XP Prof 2002 with service pack 3 version. Thank you adpotate

    (1) make sure that u run "NET START WZCSVC" on the command-line as soon as u Ouvrezunesession WINDOWS XP (START, RUN, NET START WZCSVC (command line)).

    (2) START, CONNECT, WIRELESS INTERNET CONNECTION

    --> under the 'GÉNÉRAL' tab: (1) right click on the wireless Internet connection; (2) click on properties; (3) make sure that all THE ELEMENTS under the title "THIS CONNECTION USES THE FOLLOWING ITEMS" are COMPLETELY FUNCTIONAL, i.e. UNCHECK THE ONES THAT DO ARE NOT ACTIVE ~!  (I recently turned off AVG and that this item has been inadvertently clicked on ~!) ;

    --> on the 'ADVANCED' tab: run the NETWORK CONFIGURATION WIZARD to reset your network

    3) http://support.microsoft.com/kb/871122 --> RUN 'DIFFICULTY CE PROBLEM' (ms - fix 50469)

  • Problems with wireless USB adapter. Icon missing "Wireless network connection".

    I recently got a laptop HD malfunction cause me to start my PC from 2004. I bought a Belkin N150 Wireless USB adapter to connect to the internet connectivity. During the installation, I do not get a "Wireless network connection" icon I am running Windows XP SP3. I installed the same USB adapter on a computer running Windows XP SP2 and it works fine. I plugged it in my desktop PC and it just doesn't work! Even with my router disconnected I should still be able to see other networks WiFi available in the range (I live in a community of apartment) as he worked on the other computer it elsewhere too. I double checked the drivers, reboot the cable modem, so that appropriate services were activated and still no dice. I have read forums and I'm almost at the point of paying MS for technical support services, but it's really just my last step before I shell out money for professional help. Notice to lovers? =)

    Hello

    Well, at this point, you should make an executive decision.

    If you think that someone will take just guilt because it's comfortable, it is not going to happen.

    If a new card that is known to work does not work, then you can try to re - install Windows.

    One of the differences between computer enthusiasts and regular users is the availability of the material. I have a set of wireless router, network cards, etc. that are known to be good.

    The components are used for the sole purpose of trying them temporarily on the troubled computers to rule out hardware problems.

    -------------------------------
    My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.

  • I lose the internet connection randomly but never lose my wireless network connection.

    I use a hp pavilion dv9500 with 64-bit vista sp2 and built in a wireless adapter that will fall randomly my internet wireless connection, but maintains my wireless network connection with an excellent signal strength.

    My (non-permanent) fixed
    I know how to reconnect to the internet, but it forces me to diagnose a repair my connection. It then displays "cannot connect to Server primary dns (75.75.75.75)"after which it gives "things to try" who never work and a button 'Reset the ip address' that I click. " repair bar will fill up to half way and go to a new screen solution that shows more 'solutions' and a "reset wireless adapter" button which I click. the remedy bar will fill and then display windows can not solve the problem and go for help. I then manually disconnect from the wireless network and my computer will automatically reconnect to the network and to the internet. It takes about five minutes to fix, but it happens so often that it is getting boring. The process will not work if I only to reset the ip address and then disconnect from the network, only to reset the wireless adapter and then disconnect, or just disconnect from the network and reconnect. I have to reset the ip address and the wireless adapter and then disconnect from the network.

    The internet connection will tend to disconnect when I watch a lot of youtube videos, when I download large files like a game on steam, or just just randomly when I use it. I'll use it for a long time and he can't let it go, but sometimes it will go down to ten minutes after I had just reconnected in a drop-down list. It happens randomly without another warning that download time will increase from 2 mb to 50 k in two seconds all about or stop the loading of a youtube video when I look at it.
    I searched everywhere for an answer, but it's as if it were a new problem for all humanity or just im the only person who does not know how to solve this problem, because there are no forums or FAQ not related to my problem. It is not so much a serious problem such as an irritating problem that appears at inconvenient times or when I just want to relax and watch a video. It takes some time to reconnect and even though I know how it would be better if my connection would just stay connected to the internet at any time.
    I have no idea what the problem could be that whenever I have find I never get related problems. all advice or solution would be great.
    I also share this modem with other three commonly used computers: a wired office and two other laptops that the two are connected wirelessly. both other laptops do not have the same problem as mine. My router is a linksys e3000 wireless router.

    Hi DustinMoor3,

    Follow the troubleshooting steps posted by Shekhar (marked as the answer) in this thread to solve the problem with no connection to the primary DNS server, in particular the method 2 worked for other users.

    * These steps should also work for Vista *.

  • No Internet access, the 'Connect to the Local network' and 'Wireless network connection' are "Local only".

    I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:

    Deactivation and reactivation of these two connections: FAIL.

    "Diagnose and repair" on the two connections: FAIL.

    Under dynamic I.P. type to static/static to the dynamic: FAIL.

    Uninstalled all network via Device Manager devices, then restart: FAIL.

    Manually uninstalled all the drivers and utility and installed the latest versions: FAIL

    The command ipconfig/all text follows:

    ----------------------------------------------
    Microsoft Windows [Version 6.0.6002]
    Copyright (c) 2006 Microsoft Corporation. All rights reserved.

    C:\Users\Brooklyn's>ipconfig/all

    Windows IP configuration

    Name of the host...: Brooklyns-PC
    Primary Dns suffix...:
    Node... type: broadcast
    Active... IP routing: No.
    Active... proxy WINS: No.

    Wireless network connection Wireless LAN adapter:

    The connection-specific DNS suffix. :
    ... Description: Intel (r) Wireless WiFi Link 4965AGN
    Physical address.... : 00-21-5C-31-87-95
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes
    Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
    ... Subnet mask: 255.255.0.0.
    ... Default gateway. :
    NetBIOS over TCP/IP...: enabled

    Ethernet connection to the Local network card:

    The connection-specific DNS suffix. :
    Description...: Realtek RTL8102E Family PCI - E Fast Ethern
    and NIC (NDIS 6.0)
    Physical address.... : 00-1E-33-4E-2E-F7
    DHCP active...: Yes
    Autoconfiguration enabled...: Yes
    Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
    ... Subnet mask: 255.255.0.0.
    ... Default gateway. :
    NetBIOS over TCP/IP...: enabled

    Card tunnel Local Area Connection * 6:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
    B4B}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 11:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
    0FA}
    Physical address.... : 00-00-00-00-00-00-00-E0
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    Card tunnel Local Area Connection * 14:

    State of the media...: Media disconnected
    The connection-specific DNS suffix. :
    ... Description: Teredo Tunneling Pseudo-Interface
    Physical address.... : 02-00-54-55-4E-01
    DHCP active...: No.
    Autoconfiguration enabled...: Yes

    C:\Users\Brooklyn's >
    --------------------------------------------------

    Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!

    I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.

  • The 'Wireless Network Connection 3' network card is not properly configured to use the IP protocol

    I can't connect to any internet. I'm trying to connect to wireless hotspots, but it tells me that I am connected with limited access

    Hi idkmyname

     

    1. What is the exact error message displayed when you try to go online?
    2. do you have updated the network card drivers installed?
    3. What is the brand and model of the computer?

     

    Method 1:
    You can check the links below and check out them if the steps to help you resolve the issue-
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

    You can also check the help links below-
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks
    http://Windows.Microsoft.com/en-us/Windows/help/wireless-network-connection-problems-in-Windows

    Method 2:
    You can follow the steps below to check the NIC in Device Manager. I suggest you to uninstall and reinstall the NIC drivers and check:

    a. click Startand then click Control Panel.

    b. click system and Maintenance, click Systemand then click on Device Manager.
    Note If Control Panel is in Classic view, double-click System, and then click Device Manager.
    If you are prompted for an administrator password or a confirmation, type the password, or click allow.
    Check if you have any exclamation point beside the devices listed. If you have, then there is problem with the card is installed.

    c. in the NIC, expand adapter, right click on the devices listed and then click Uninstall.
    When you are prompted to confirm that you want to remove the device, click OK.

    d. restart the computer.

    After the computer restarts, the drivers will be installed automatically. Check after this procedure if you are able to get access to the network.

     

    If you get all the drivers related errors, you can check if you have the latest drivers updated, installed for the network card. See the help link - below
    http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly


    I hope this helps.

Maybe you are looking for

  • 10.11.6 updating crippled my Mac Pro

    Problems after update 10.11.6 - system preferences will not open the shutters, can't seem to find any application that opens - reports of damaged applications, including disk utility, console, etc. Reboot and shutdown / reboot erase it. Are here look

  • Newly created images will be displayed in Firefox 8 for Mac. Same images appear in other browsers. Why?

    1. the new images are uploaded, but will not appear in Firefox on my Mac with OS 10.6.8 8. (Does not appear in other browsers, for example, Chrome, and Opera and appears on 8 Firefox for PC). In addition, other images of the display of the page. 2. I

  • HP Envy 17-184na and Envy 17-141na

    I was comparing prices from different stores on a laptop computer called the HP Envy 17-j184na and found one called the HP Envy 17-j141na. Both laptops I found have model names different but seem exactly the same for me, so my question is: What is th

  • Lock/unlock blackBerry smartphones the BB 9700

    Recently, I improve my OS and fails on my phone. Before upgrading the operating system, by pressing the upper left locked the phone. Also by pressing [A] locked the phone. Now, these functions do not work. Help, please. Thank you

  • What is the preferred means of creating group policies?

    What is the preferred means of creating group policies? For example policy of GP1 for wallpaper and GP2 political mapping of drive and printer. or to combine politics both GP1 and GP2 in unique group as GPDOMAIN policy.