Z600: computer does not start after the installation of the 5 TB SATA drive

Similar Questions

• computer does not start after the installation of vista updates.

  computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

  Hello

  Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

  Hope that information was useful

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• M127FW MFP: Computer does not start after the installation of the MFP M127FW

  My computer does not start on my hard drive after installation of my new printer MFP M127FW unless I have first of all disconnect the USB cable between the printer and then turn on the computer.  My BIOS is set to boot from my drive hard, not from a USB key, so that makes installing the drivers M127FW MFP and software do on my computer?  I guess it has something to do with the Smart Install feature.

  "On the printer, press Setup, maintenance, Smart Install and stop."

  It worked.  Thank you.

• You can save a broken computer? My computer does NOT start after the blue hp screen.

  In the past months, my computer has been the object of a freezing randomly, and Ctrl + Alt + Delete does not work. I stopped him via the power button. Sometimes, when I start it again, the computer moniter shows nothing but a black screen and the computer sounds different when it starts normally. When this happens, I turn it off again hit the left side of the desktop and turn on again. Whenever I do this, the computer starts normally, and I go on the computer use.

  Yesterday morning, after a break of 2 days, acess my computer and it is random freezing thing once again. I force close down as one normally do, and the computer does not start and displays the same black screen and the same fan/air weird sound. I stopped him and I hit the side RIGHT this time, I think and when I turn on the computer, the usual blue HP screen appears with the establishment, boot, diagnostics and system recovery things. HOWEVER, after this screen, a black screen will appear with this weird blue symbol on the upper left corner, I have never seen this and it looks like a circle with a triangle and a Pentagon below and it remains essentially on this screen forever. When I try to hit the establishment, boot, diagnostics and the shortcuts to system recovery, on the lower left side of the screen, it says "Menu boot loading...". ' or whatever the shortcut of loading represents, but nothing ever happens. When I press the other keys, this tapping noise comes from the computer at each tap of the keyboard.

  I have no idea what to do, and at this point, my first priority is to save important files on the computer. Does anyone know what is the problem? I want her more than a problem of system rather than a virus problem because refusing the boot black screen thing lasts for years. My computer is 3-4 years. I enclose a sketch of what looks like the weird symbol.

  

  MY COMPUTER WORKS NOW!

  With the flash drive, I was able to access the BIOS, which before, I couldn't.

  Eventually my computer was in some strange sort of lockdown setting, I switched it back to activate and now its work! I remember save important things in the future. Thank you very much for your help!

• Computer does not start after the screen goes blank &amp; Compaq.

  Hello

  A few weeks ago, I turned on my PC and it showed at the Compaq screen and then went to a blank screen & would not respond. I held the switch button to turn it off and after 4 attempts, it start fine. Next time, it took 20 attempts to initialize and now it does not start, it will be maybe if I try like 100 times he can do... The problem is when the Compaq screen comes up it comes only for like a second so I know that it does not start, if the Compaq screen stays for a few seconds as 3 + I know it will load windows and start.

  History > the computer originally had XP and has been replaced with VISTA memory was 2 * 512MB, but it was a bit slow and I was advised to upgrade. I bought 2 * 1 GB memory and put it in my PC a few months there may be 5 + had no problem so far.

  I tried the following:

  Remove the memory and replace it. Remove the 2 * 1 GB of memory and its replacement by the Moose 2 * 512MB to check if the memory is at fault.

  Cleaning of the dust around the fan (at this point, I removed the fan over the CPU and cleaned the thermal compound from the CPU to make it nice and shiny, only tried to start one time after that for a few seconds heard blowing fan and turend it took off. Depuis_lors, I realized that it wasn't just muck and had a purpose na derwiche put a little more on)

  Remove the battery of the BIOS for half a day

  Move jumpers CMOS from1, 2 to 2, 3 positions

  I can not get into the same if BIOS start and hold F1 he will show me the BIOS for a second and then go to a black screen.

  Specifications of the computer

  Compaq Presario SR1629UK desktop PC

  Details can be found in the following link

  http://support.HP.com/us-en/document/c00579251

  Your help would me much appreciated...

  Hi guys,.

  Thanks for your help, I wanted to just give you a batch update. After the grueling process of verifying the destop, memory suppression, cleaning it & all the other techo checks. I gave my pc to somone to look to the he tried not to turn on he opened it removed cleaning my thermal paste back on and told me it was working fine.

  When I bought home all happy, I realized that I had the same problem, I borrowed another monitor and found it worked well! So the question is with my monitor, if anyone has the same problem first check another monitor.

• H8 - 1280t - QC461AV #ABA: desktop HP - computer does not start after the installation (Windows 10) video card

  So, I just bought a new video card an XFX R9-390 and a new HX1200i POWER supply corsair (overkill ik ) that I put on a card mother IPIWB-PB for my 3 years old HP PC, and the new stupid video card is not working. the PC just does not start, I see is a black screen. My monitor is an HP 2311gt and I can't use my computer with the old video card no probs, BUT whenever I have to install the new card does not detect my monitor just and I only see a blank screen. I HAVE NO IDEA HOW I'M DOING. Help, please

  PS. I have RMA the new power supply and the video card and they got to check and send back to me, so I know that the two pieces of equipment are working very well AND of course I am currently using my PC with the old video card

  Wiraqocha, here is the link to start safe for HPs with Win 10 and instructions to enter the BIOS. It may be useful:

  HP PC - secure boot (Windows 10)

• Computer does not start after the installation of Win XP SP3

  original title: ServicePack 3 does not work

  After loading service pack 3 my computer does not upwards, unless I use safe mode. It restores not to any restore point. I uninstall and go back to service pack two and get constant reminders to update three when it won't work. After saying it works fine if a little slow in two so is there any point of update.

  Recently, I reset my computer to factory settings to erase the disc from loads of unwanted waste and programs. Reloaded ServicePack two, he wouldn't go back with gel. After reading the old posts, I found a link to Jespers blog. It contained a small tool that intelPPM problems detected and then given the option to turn off the setting. http://msinfluentials.com/blogs/jesper/archive/2008/05/08/does-your-amd-based-computer-boot-after-installing-xp-sp3.aspx.

  This fixes the problem and service pack three charges and now works fine. The tool is loaded in seconds.

• computer does not start after the installation of updates

  Just click on the button "installs the update and the computer shuts down."  When the computer turns off automatically, I pushed the power button and now it is frozen the computer in start mode.  What should I do now?  Can I power off and try again (or which will mess up the configuration of the update that he just installed.

  Note: There are 21 updates installed last night without problem; then 1 update again (that set up correctly when I restarted this morning).  After a successful this morning launch, I noticed there was an another update to install, which is what made me at this point.

  Single computer at home (I use my work computer to submit this application).

  Wait awhile and see if, during the initialization of the problem to be solved or not. It is NOT a good idea to unplug the laptop.

  If this does not work, then try to press F8 and choose last known good configration, but you may need to reinstall the update again.

• computer does not start after the BIOS screen

  My computer froze when I was able to do it after a few minutes I turned off the computer.  My mistake, now I can not get windows to load. The monitor

  becomes black after the dell logo appears.  The only options I have are F2 and F12.  What other options I have to troubleshoot? Thanks in advance

  for all the answers

  Hello

  see if you can run the dell Diagnostics

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?c=us&CS=19&l=en&s=DHS&docid=DSN_A9E3A15597A04AFBB02EE16785D39C5C&isLegacy=true

  and use step 3 it if it finds an error

• Inspiron 13-5323 does not start after the new installed hard drive

  Fall of my Inspiron and Geek Squad said she needed a new hard drive.  I installed a new identical to the former myself blue WD.  When activated, it immediately passes to "Phoenix Securecore Tiano Setup.  Pre-launch tests indicate that the new hard drive works fine.  I tried to start in safe mode UEFI and in the boot Legacy mode, but no boot.  I get a message "Not found operating system".  It is my understanding that this computer has an operating system embedded on the motherboard.  I previously had it improved Windows 8.1 to 10.  When I tried to boot mode safe mode using F8, I had the same operating system not found message.  The F2 and F4 keys on commissioning do nothing different, either.  Am I missing a step in the window settings of Phoenix?  Suggestions while in Phoenix window bringing me could happen to start the system would be appreciated.

  In fact you have reloaded the operating system?  If not, the new drive is empty - it's why you see the message you see.

  You will need all the recovery media, as you did when you received the system - or, if you do not prepare a set, you will need to call Dell to buy a flash drive with the media today.  The alternative is to download Windows 10 TH2, of the same version (standard, pro) that has been installed and activated previously.  You can then reload the operating system.

• XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

  Original title: xp does not start after the installation of avira

  I have a HP Slimline s7410
  XP Home Edition SP3
  I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
  I have a cd/dvd drive of work.
  I don't have an XP bootable installation CD

  My system worked well until: I installed the free version of Avira

  Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
  I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

  Here's what my BSOD looks like:

  Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

  Any help is greatly appreciated! :)

  My first suggestion is to do a system restore at this time point.

  second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

  third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

  Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

  so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

  fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.